Rubrene薄层的位置对器件发光性能的影响及器件内激子复合区域的分析

通过在主体材料上蒸镀一层荧光染料超薄层的方法,研究了有机小分子5,6,11,12-tetraphenyl-naphthacene(rubrene)薄层在器件中不同位置时,有机电致发光器件(OLED)的电致发光光谱及发光性能.实验发现当rubrene薄层位于NPB/AlQ界面处时,器件的发光几乎都来自rubrene的发光...     

有机/有机界面污染对有机电致发光器件稳定性的影响(英文)

有机电致发光器件的稳定性是其实用化面临的主要难题之一。为了研究有机/有机界面性质对有机电致发光器件稳定性的影响,采用溶液旋涂的NPB(NPBSC)作为器件的空穴传输层制备了两种异质结电致发光器件:ITO/NPBSC/Alq3/LiF/Al和ITO/NPBSC/NPB/Alq3/LiF/Al,对比研究了器件的发光性能和工作稳定性。研究结果表明:完全使用NPBSC作为空穴传输层的器件性能和稳定性都较差,这归因于不稳定的NPBSC/Alq3界面,在空气中旋涂制备NPB层时,空气中的水蒸气和氧气分子会粘附在空穴传输层表面,这样就会引起界面处Alq3分子的发光猝灭。插入10 nm真空蒸镀的NPB层可以显著地提高器件的发光性能和稳定性,10 nm的NPB层把污染界面与激子复合区界面分开,避免了水蒸气和氧气分子对Alq3分子的发光猝灭,器件的效率增加了1.15 cd/A,半衰期寿命提高了4倍。     

一种提高有机电致发光器件发光效率的新方法:金属超薄层

在有机电致发光器件中插入金属超薄层常会带来一些意想不到的作用。在无机材料MoQ_3与有机材料TPD之间插入5 nm金属层Au,制备了结构为ITO/MoO_3(5 nm)/Au(5 nm)/TPD/AlQ/LiF/Al的OLED器件。相对于没有金属层Au的器件,发光效率得到了提高。通过分析认为Au在TPD和MoO_3之间形成一个小的空穴陷阱,在降低了器件中的电流密度的同时,由于5nm的Au对AlQ绿光的光透过率大于80%,发光亮度未受明显影响,是发光效率提高的原因。本文为提高OLED器件发光效率提供了新的思路和实验依据。     

掺杂型红色有机电致发光显示器件

全色显示是有机电致发光显示(OLED)器件发展的目标,而高性能红色发光器件一直是制约全彩色OLED器件实用化的瓶颈,也是目前有机电致发光显示研究的热点。制作了掺杂DCJTB和不同浓度的rubrene两种荧光染料的红色有机电致发光显示器件,以NPB和Alq₃分别作为空穴传输层和电子传输层,发现器件性能与只掺杂DCJTB的器件相比有明显提高,发光效率提高到2～3倍。通过Frster理论和能带理论分析了器件的能量转移机理,研究发现Frster能量转移不是掺杂器件能量转移的主要形式,载流子俘获机制才是器件效率提高的主要原因;rubrene的引入使得能量能够更有效地从Alq₃转移到DCJTB,从而显著地提高了器件的发光效率和性能。     

利用有机层间互相掺杂提高有机电致发光器件的效率

提高器件的发光效率是实现有机电致发光器件实用化的一个关键因素。通过对器件结构和制作工艺的优化设计，将有机电致发光器件的各个功能层进行互相掺杂，在层间形成互掺过渡层达到平衡载流子的注入，使得注入的电子和空穴有效地限制在互掺的有源区内，增加了载流子相遇复合的几率，进而提高器件的发光效率。器件的最大电流效率在外加电压10．5V时达到7．9cd／A，最大发光亮度在35V时达到49000cd／m^2。和一般掺杂器件相比效率提高2倍以上。同时有机层间的互相掺杂也在一定程度上消除了层问的界面，减少了有机层问的缺陷，与没有过渡层的器件相比，器件老化性能有了明显改善。     

一种新型有机电致微腔结构的双模发射

采用结构Glass／DBR／ITO／NPB／NPB：Alq／Alq／Al制作了有机微腔电致发光器件。将空穴传输材料与发光材料以一定比例混合作为发光层，为了便于对比，在不改变有机层的膜厚的情况下同时制作了传统的异质结微腔器件，发现两种器件的发光光谱有很大不同，器件的复合效率与传统的异质结器件相比也得到了很大提高，这是因为将两种有机材料混合能消除界面势垒，提高器件的复合效率，从而提高了器件的发光性能，实现了微腔双模发射，且两个模式的半峰全宽分别为8nm和12nm。通过进一步优化器件结构可以实现微腔白光发射。     

金属/有机界面势垒对单层有机电致发光器件发光效率的影响

基于高场下电荷的注入过程及激子的解离和复合过程,建立了单层有机发光器件电致发光(EL)效率的理论模型。计算表明：(1)当金属／有机界面势垒高度大于0．3eV时,器件的EL效率很低,降低金属／有机界面势垒可以显著提高器件的EL效率;(2)在较低偏压下,注入过程对器件的电致发光效率起主要作用,但在高偏压下复合过程起支配作用。这一模型可以阐明注入和复合过程对有机发光器件EL效率的影响,对选择发光材料、优化器件结构和提高器件EL效率具有指导意义。     

纳米ZnO薄膜对有机电致发光器件性能的影响

由于有机电致发光器件(Organic light-emitting devices,OLEDs)的主动发光、高亮度等优点,在显示和照明领域有极大的应用前景。报道了纳米ZnO薄膜对这种发光器件性能的影响。在普通有机电致发光器件空穴传输层和发光层之间直接蒸镀一层纳米ZnO薄膜,当纳米ZnO薄膜的厚度为1nm时,器件的电流效率可达3.26cd/A,是没有纳米ZnO薄膜同类器件的1.24倍。适当厚度的纳米ZnO薄膜降低了发光层空穴的浓度,提高了电子和空穴的平衡,从而提高了器件的效率。     

一种高电流密度下效率不降低的绿光有机电致发光器件

为了提高有机电致发光器件(OLED)在高电流密度下的发光效率, 在以C545T掺杂Alq₃为发光层的有机小分子绿光器件中的发光层与电子传输层之间插入超薄LiF绝缘层.结果表明, 器件的外量子效率随着电流密度的增加始终没有降低, 直至600 mA/cm²时达到最大值 4.79%, 是相同电流密度下的参考器件的外量子效率的7倍.     

利用电子传输层掺杂改善有机发光器件的效率

利用BCP掺杂到电子传输层Alq中,在掺杂层中阻挡了空穴的迁移,调整了空穴和电子的平衡,将激子有效地限制在发光层中发光,从而增加有机电致发光器件的效率.器件的最大电流效率在外加电压9 V时达到4.1 cd/A(掺杂浓度8%时),与一般未掺杂器件相比效率提高了2倍多.同时也减少空穴到达阴极,而减少发光淬灭.     

互混型有机电致发光器件

通过共蒸镀空穴传输材料TPD和电子传输材料Alq₃,在普通双层器件的异质结界面引入了均匀互混层,并研究了互混层的厚度变化对器件光电性能的影响。互混层的引入在一定程度上改善了普通双层器件的异质结界面由于高浓度载流子积聚导致的高电场和界面缺陷对器件主要性能(效率和寿命)的负面影响。我们发现一定厚度的互混层使器件的性能有所提高。     

High efficiency rubrene based inverted top-emission organic light emitting devices with a mixed single layer

Inverted top-emission organic light emitting devices (TEOLEDs) with a mixed single layer by mixing of electron transport materials (PyPySPyPy and Alq₃), hole transport material (α-NPD) and dope material (rubrene) were investigated. Maximum power efficiency of 3.5 lm/W and maximum luminance of 7000 cd/m² were obtained by optimizing the mixing ratio of PyPySPyPy:Alq₃:α-NPD:rubrene=25:50:25:1. Luminance and power efficiency of mixed single layer device were two times improved compared to bi-layer heterojunction device and tri-layer heterojunction device. Lifetime test also shows that the mixed single layer device exhibits longer operational lifetimes of 343 h, which is three times longer than the 109 h for tri-layer device, and two times longer than the 158 h for bi-layer device. In addition, the maximum luminance and power efficiency were obtained at 20,000 cd/m² and 7.5 lm/W, respectively, when a TPD layer of 45 nm was capped onto the top metal electrode.     

采用热处理方法提高MEH-PPV单层聚合物有机发光二极管发光性能的研究

对以MEH－PPV为发光层的单层聚合物有机发光二极管（OLED）器件在最佳条件下进行真空热处理，并用金相显微镜观察施加电压后器件的阴极表面形貌。发现处理后的器件阴极表面的气泡及黑斑明显减少。器件的发光性能显著提高。与未经处理的器件相比，最大相对发光强度提高了一个数量级、启亮电压降低了2．0V，半寿命提高了12．7倍。初步分析表明热处理方法提高器件发光性能的主要原因在于有效地减少了器件在工作过程中由于焦耳热产生的某些气体，从而减少阴极表面气泡及黑斑的出现，另一方面，热处理方法也增强了有机发光层与阴极接触界面的结合力，提高电子注入水平。     

通过插入Au薄膜改善绿光OLED器件的发光色纯度

在一些有机电致发光器件中,Au常被用作阳极,研究者希望Au在导电的同时兼具半透明可出光的属性,这要求Au在能导电的同时厚度要尽量薄。因此制备两种金属共同组成电极成为了选择。将半透明Au/Al层插入阳极一侧,制备了结构为ITO/Al(16 nm)/Au(10 nm)/TPD(30 nm)/AlQ(30 nm)/LiF(0.5 nm)/Al的OLED器件,相对于器件ITO/TPD(30 nm)/AlQ(30 nm)/LiF(0.5 nm)/Al在长波方向出现了光谱窄化现象,通过分析和实验判断该现象是Au薄膜特有的对光的选择透过性造成,而并非微腔效应。阳极一侧加入了Au/Al的器件保持了广视角无角度依赖的优点,同时可以输出滤掉部分红光的纯度更高的发光,发光色纯度得到了改善。     

Enhanced power efficiency for white OLED with MoO3 as hole injection layer and optimized charge balance

White OLEDs with a different hole injection layer (MoO₃ or m-MTDATA), and a different electron transport layer (Alq₃ or Bphen) have been investigated. With 9,10-bis (2-naphthyl)-2-t-butylanthracene (TBADN) doped with 3% P-bis (P-N, N-diphenyl-aminostyryl) benzene (DSA-ph) and 0.05% 4-(dicyanomethylene)-2-t-butyl-6-(1,1,7,7,-tetramethyl-julolidy-9-enyl)-4H-pyran (DCJTB) as white emitting layer, the MoO₃/ /Bphen based device shows the lowest driving voltage and highest power efficiency among the referenced devices. At the current density of 20 mA/cm², its driving voltage and power efficiency are 5.43 V and 4.54 lm/W respectively, which is independently reduced 40% and improved 57% compared with those of the m-MTDATA/ / Alq₃ based one, respectively. The energy level diagram of the devices and single-carrier devices are studied to explain the reasons for the improvement. The results strongly indicate that carrier injection ability and balance shows a key significance in OLED performance.     

Performance improvement of rubrene-based organic light emitting devices with a mixed single layer

We have investigated the performance of organic light-emitting devices (OLEDs) with a rubrene-doped mixed single layer by using 4,4′-bis[N-(1-napthyl)-N-phenyl- amion] biphenyl (α-NPD) as hole transport layer. Comparing to a conventional heterostructure OLED, equal luminance vs. current density characteristics were obtained. In addition, maximum power efficiency was threefold improved, and the achieved value was 5.90 lm/W by optimizing a mixing ratio of hole and electron transport materials. By evaluating the temperature dependence of the J – V characteristics for electron-injection dominated device, the electron injection from Al/LiF to mixed organic layer is attributed to Schottky thermal emission model. And the barrier height of the electron injection from Al/LiF into mixed single layer was obtained to be 0.62 eV, which is lower than Al/Alq₃ interface. Meanwhile, the mixed single-layer device exhibited superior operational durability at a half-luminance of 2,250 h under a constant current operation mode. The reliability was improved with a factor of two compared to the heterostructure device due to the improvement of stability in mixed organic molecules and removal of the heterojunction interface in the mixed single-layer device.     

复合阴极缓冲层Alq_3∶CsF对CuPc/C_(60)电池性能的影响

通过Alq_3∶CsF复合阴极缓冲层来优化CuPc/C_(60)有机小分子太阳能电池的性能。当Alq_3∶CsF厚度为5nm,CsF的掺杂比例为4%时,加入复合阴极缓冲层器件较Alq_3阴极缓冲层器件的能量转化效率提高了49%,到达0.76%,并且在室温、大气的条件下,器件的稳定性也得到了保持,与未加阴极缓冲层的器件相比,半衰期提高了6倍,达到9.8h。通过紫外-可见吸收、外量子效率和单载流子传输器件等研究了器件效率改善的主要原因是掺入CsF后,调节界面能级,改善了Alq_3的电子传输特性,提高了器件的短路电流和填充因子。比较分析复合阴极缓冲层器件于空气中放置不同的时间的电流电压曲线,表明Alq_3∶CsF可以保持Alq_3的良好稳定性,可以很好地阻挡氧气与水分的扩散,提高器件的寿命。     

Improved blue quantum dot light-emitting diodes via chlorine passivated ZnO nanoparticle layer

In blue quantum dot light emitting diodes (QLEDs), electron injection is insufficient, which would degrade device efficiency and stability. Herein, we employ chlorine passivated ZnO nanoparticles as electron transport layer to facilitate electron injection into QDs effectively. Moreover, it suppresses exciton quenching at the QD/ZnO interface by blocking charge transfer channel. As a result, the maximum external quantum efficiency of blue QLED was increased from 2.55% to 4.60%, and the operation lifetime of blue QLED was nearly 4 times longer than that of the control device. Our work indicates that election injection plays an important role in blue QLED efficiency and stability.     

有机微腔绿色发光二极管

光学微腔是指尺寸在光波长量级的光学微型谐振腔。微腔结构可以使腔内物质和光场的相互作用与体材料相比发生很大变化,出现了自发辐射谱线窄化和增强等腔效应。利用这些腔效应,可以改善有机发光器件的性能。采用微腔结构,优化设计并研制了有机微腔绿色发光二极管,器件结构为Glass/DBR/ITO/NPB/Alq∶Rubrene/Alq/MgAg,获得了最大亮度40100 cd/m2、最大发光效率为6.44 cd/A、半峰全宽为28 nm的纯绿色有机微腔电致发光器件。而与之比较的无腔器件最大亮度为22580 cd/m2、最大发光效率为2.98 cd/A、半峰全宽为120 nm。相同电流密度下微腔电致发光谱的峰值发射强度是无腔器件的4.2倍。结果表明将微腔结构引入有机电致发光器件中,不但改善了发光的色纯度,而且使器件的发光效率和亮度都得到明显增强。     

Optically controlled SiCGe/SiC heterojunction transistor with charge-compensation layer

A novel optically controlled SiCGe/SiC heterojunction transistor with charge-compensation technique has been simulated by using commercial simulator.This paper discusses the electric field distribution,spectral response and transient response of the device.Due to utilizing p-SiCGe charge-compensation layer,the responsivity increases nearly two times and breakdown voltage increases 33%.The switching characteristic illustrates that the device is latch-free and its fall time is much longer than the rise time.With an increase of the light power density and wavelength,the rise time and fall time will become shorter and longer,respectively.In terms of carrier lifetime,a compromise should be made between the responsivity and switching speed,the ratio of them reaches maximum value when the minority carrier lifetime equals 90 ns.