Plasmonic‐Induced Photon Recycling in Metal Halide Perovskite Solar Cells

Organic–inorganic metal halide perovskite solar cells have emerged in the past few years to promise highly efficient photovoltaic devices at low costs. Here, temperature‐sensitive core–shell Ag@TiO₂ nanoparticles are successfully incorporated into perovskite solar cells through a low‐temperature processing route, boosting the measured device efficiencies up to 16.3%. Experimental evidence is shown and a theoretical model is developed which predicts that the presence of highly polarizable nanoparticles enhances the radiative decay of excitons and increases the reabsorption of emitted radiation, representing a novel photon recycling scheme. The work elucidates the complicated subtle interactions between light and matter in plasmonic photovoltaic composites. Photonic and plasmonic schemes such as this may help to move highly efficient perovskite solar cells closer to the theoretical limiting efficiencies.     

Double‐Sided Surface Passivation of 3D Perovskite Film for High‐Efficiency Mixed‐Dimensional Perovskite Solar Cells

Defect‐mediated carrier recombination at the interfaces between perovskite and neighboring charge transport layers limits the efficiency of most state‐of‐the‐art perovskite solar cells. Passivation of interfacial defects is thus essential for attaining cell efficiencies close to the theoretical limit. In this work, a novel double‐sided passivation of 3D perovskite films is demonstrated with thin surface layers of bulky organic cation–based halide compound forming 2D layered perovskite. Highly efficient (22.77%) mixed‐dimensional perovskite devices with a remarkable open‐circuit voltage of 1.2 V are reported for a perovskite film having an optical bandgap of ≈1.6 eV. Using a combination of experimental and numerical analyses, it is shown that the double‐sided surface layers provide effective defect passivation at both the electron and hole transport layer interfaces, suppressing surface recombination on both sides of the active layer. Despite the semi‐insulating nature of the passivation layers, an increase in the fill factor of optimized cells is observed. The efficient carrier extraction is explained by incomplete surface coverage of the 2D perovskite layer, allowing charge transport through localized unpassivated regions, similar to tunnel‐oxide passivation layers used in silicon photovoltaics. Optimization of the defect passivation properties of these films has the potential to further increase cell efficiencies.     

Synthesis of Core–Shell Inorganic Nanotubes

New materials and techniques pertaining to the synthesis of inorganic nanotubes have been ever increasing since the initiation of the field in 1992. Recently, WS₂ nanotubes, which are produced now in large amounts, were filled with molten lead iodide salt by a capillary wetting process, resulting in PbI₂@WS₂ core–shell nanotubes. This work features progress in the synthesis of new core–shell nanotubes, including BiI₃@WS₂ nanotubes produced in a similar same manner. In addition, two new techniques for obtaining core–shell nanotubes are presented. The first is via electron‐beam irradiation, i.e., in situ synthesis within a transmission electron microscope. This synthesis results in SbI₃ nanotubes, observed either in a hollow core of WS₂ ones (SbI₃@WS₂ nanotubes), or atop of them (WS₂@SbI₃ nanotubes). The second technique involves a gaseous phase reaction, where the layered product employs WS₂ nanotubes as nucleation sites. In this case, the MoS₂ layers most often cover the WS₂ nanotube, resulting in WS₂@MoS₂ core–shell nanotubes. Notably, superstructures of the form MoS₂@WS₂@MoS₂ are occasionally obtained. Using a semi‐empirical model, it is shown that the PbI₂ nanotubes become stable within the core of MoS₂ nanotubes only above a critical core diameter of the host (>12 nm); below this diameter the PbI₂ crystallizes as nanowires. These model calculations are in agreement with the current experimental observations, providing further support to the growth mechanism of such core–shell nanotubes.     

Integrated Quasi-2D Perovskite/Organic Solar Cells with Efficiency over 19% Promoted by Interface Passivation

Integrated perovskite/organic solar cells (IPOSCs) have shown great potential in broadening the light absorption range and improving the photovoltaic performance. However, the severe interface charge recombination and unmatched energy levels between perovskite and organic photoactive layers hinder their performance improvement. Here, an efficient interface passivation strategy for IPOSCs based on a layered Ruddlesden–Popper (RP) perovskite and high photovoltaic performance is successfully demonstrated. It is found that an ultrathin conjugated polymer (PM6) layer could passivate the surface defects of perovskite film, tuning the energy level and suppress the nonradiative recombination loss, leading to efficient interface contact between RP perovskite and organic photoactive layers, boosting the open-circuit voltage from 1.06 to 1.12 V and the efficiency from 17.23% to 19.15%. Importantly, the optimized device shows extended photocurrent response to 930 nm with a peak intensity close to 50% from 800 to 931 nm. The results indicate that interface passivation using a functionalized polymer could be an efficient strategy to improve the photovoltaic performance of integrated devices.     

Conjugated Polymer–Assisted Grain Boundary Passivation for Efficient Inverted Planar Perovskite Solar Cells

Grain boundaries in lead halide perovskite films lead to increased recombination losses and decreased device stability under illumination due to defect‐mediated ion migration. The effect of a conjugated polymer additive, poly(bithiophene imide) (PBTI), is investigated in the antisolvent treatment step in the perovskite film deposition by comprehensive characterization of perovskite film properties and the performance of inverted planar perovskite solar cells (PSCs). PBTI is found to be incorporated within grain boundaries, which results in an improvement in perovskite film crystallinity and reduced defects. The successful defect passivation by PBTI yields reduces recombination losses and consequently increases power conversion efficiency (PCE). In addition, it gives rise to improved photoluminescence stability and improved PSC stability under illumination which can be attributed to reduced ion migration. The optimal devices exhibit a PCE of 20.67% compared to 18.89% of control devices without PBTI, while they retain over 70% of the initial efficiency after 600 h under 1 sun illumination compared to 56% for the control devices.     

Field‐Tuneable Diamagnetism in Ferromagnetic–Superconducting Core–Shell Structures

Three dimensional ferromagnet–superconductor core–shell structures are realized by electrocrystallisation and their magnetic properties investigated. We observe fully re‐entrant core superconductivity in increasing fields that survives well above the bulk critical field due to compensation effects. The net measured magnetization of optimized structures could be switched from absolute para(ferro‐)magnetic to diamagnetic by tuning the external magnetic field. Micromagnetic simulations of the structures are in good qualitative agreement with our results.     

Ultralong CdTe Nanowires: Catalyst‐Free Synthesis and High‐Yield Transformation into Core–Shell Heterostructures

A novel catalyst‐free synthetic strategy for producing high‐quality CdTe nanowires in solution is proposed. A special reaction condition is intentionally constructed in the reaction system to induce the formation of nanowires through oriented in situ assembly of tiny particles. To establish such special synthetic conditions in the CdTe system, not only are its typical features and possible solutions deeply analyzed, but also related factors, such as the ligand environment, injection and growth temperature, and Cd‐to‐Te precursor ratio, are systemically investigated. High‐quality ultralong (up to 10 μm) and ultrathin (less than 10 nm) CdTe nanowires are produced in solution under optimal reaction conditions. Morphological, spectral, and compositional analyses are performed to examine the products formed at different reaction stages in order to clarify the formation mechanism of the CdTe nanowires. Furthermore, the transformation of the CdTe nanowires into CdTe/CdSe core–shell heterostructures is intensively explored, and the CdSe epitaxial growth process is specially tracked by morphological and spectral characterization techniques. Finally, CdTe nanowires coated with a continuous and dense CdSe shell are successfully fabricated by using a proper coating protocol.     

Interface Dipole Induced Field-Effect Passivation for Achieving 21.7% Efficiency and Stable Perovskite Solar Cells

Organolead halide hybrid perovskite solar cells (PSCs) have become a shining star in the renewable devices field due to the sharp growth of power conversion efficiency; however, interfacial recombination and carrier-extraction losses at heterointerfaces between the perovskite active layer and the carrier transport layers remain the two main obstacles to further improve the power conversion efficiency. Here, novel field-effect passivation has been successfully induced to effectively suppress the interfacial recombination and improve interfacial charge transfer by incorporating interfacial polarization via inserting a high work function interlayer between perovskite and holes transport layer. The charge dynamics within the device and the mechanism of the field-effect passivation are elucidated in detail. The unique interfacial dipoles reinforce the built-in field and prevent the photogenerated charges from recombining, resulting in power conversion efficiency up to 21.7% with negligible hysteresis. Furthermore, the hydrophobic interlayer also suppresses the perovskite decomposition by preventing the moisture penetration, thereby improving the humidity stability of the PSCs (>91% of the initial power conversion efficiency (PCE) after 30 d in 65 ± 5% humidity). Finally, several promising research perspectives based on field-effect passivation are also suggested for further conversion efficiency improvements and photovoltaic applications.     

Triplex Au–Ag–C Core–Shell Nanoparticles as a Novel Raman Label

Monodispersed, readily‐grafted, and biocompatible surface‐enhanced Raman spectroscopic (SERS) tagging materials are developed; they are composed of bimetallic Au@Ag nanoparticles (NPs) for optical enhancement, a reporter molecule for spectroscopic signature, and a carbon shell for protection and bioconjugation. A controllable and convenient hydrothermal synthetic route is presented to synthesize the layer‐by‐layer triplex Au–Ag–C core–shell NPs, which can incorporate the Raman‐active label 4‐mercapto benzoic acid (4‐MBA). The obtained gold seed–silver coated particles can be coated further with a thickness‐controlled carbon shell to form colloidal carbon‐encapsulated Au_core/Ag_shell spheres with a monodisperse size distribution. Furthermore, these SERS‐active spheres demonstrated interesting properties as a novel Raman tag for quantitative immunoassays. The results suggest such SERS tags can be used for multiplex and ultrasensitive detection of biomolecules as well as nontoxic, in vivo molecular imaging of animal or plant tissues.     

Passivated Perovskite Crystallization via g‐C3N4 for High‐Performance Solar Cells

Organometallic halide perovskite films with good surface morphology and large grain size are desirable for obtaining high‐performance photovoltaic devices. However, defects and related trap sites are generated inevitably at grain boundaries and on surfaces of solution‐processed polycrystalline perovskite films. Seeking facial and efficient methods to passivate the perovskite film for minimizing defect density is necessary for further improving the photovoltaic performance. Here, a convenient strategy is developed to improve perovskite crystallization by incorporating a 2D polymeric material of graphitic carbon nitride (g‐C₃N₄) into the perovskite layer. The addition of g‐C₃N₄ results in improved crystalline quality of perovskite film with large grain size by retarding the crystallization rate, and reduced intrinsic defect density by passivating charge recombination centers around the grain boundaries. In addition, g‐C₃N₄ doping increases the film conductivity of perovskite layer, which is beneficial for charge transport in perovskite light‐absorption layer. Consequently, a champion device with a maximum power conversion efficiency of 19.49% is approached owing to a remarkable improvement in fill factor from 0.65 to 0.74. This finding demonstrates a simple method to passivate the perovskite film by controlling the crystallization and reducing the defect density.     

Core–Shell Nanoparticles: Characterizing Multifunctional Materials beyond Imaging—Distinguishing and Quantifying Perfect and Broken Shells

Core–shell nanoparticles (NPs) are amongst the most promising candidates in the development of new functional materials. Their fabrication and characterization are challenging, in particular when thin and intact shells are needed. To date no technique has been available that differentiates between intact and broken or cracked shells. Here a method is presented to distinguish and quantify these types of shells in a single cyclic voltammetry experiment by using the different electrochemical reactivities of the core and the shell material. A simple comparison of the charge measured during the stripping of the core material before and after the removal of the shell makes it possible to determine the quality of the shells and to estimate their thickness. As a proof‐of‐concept two multifunctional examples of core–shell NPs, Fe₃O₄@Au and Au@SnO₂, are used. This general and original method can be applied whenever core and shell materials show different redox properties. Because billions of NPs are probed simultaneously and at a low cost, this method is a convenient new screening tool for the development of new multifunctional core–shell materials and is hence a powerful complementary technique or even an alternative to the state‐of‐the‐art characterization of core–shell NPs by TEM.     

High‐Performance Sodium‐Ion Hybrid Supercapacitor Based on Nb2O5@Carbon Core–Shell Nanoparticles and Reduced Graphene Oxide Nanocomposites

Sodium‐ion hybrid supercapacitors (Na‐HSCs) have potential for mid‐ to large‐scale energy storage applications because of their high energy/power densities, long cycle life, and the low cost of sodium. However, one of the obstacles to developing Na‐HSCs is the imbalance of kinetics from different charge storage mechanisms between the sluggish faradaic anode and the rapid non‐faradaic capacitive cathode. Thus, to develop high‐power Na‐HSC anode materials, this paper presents the facile synthesis of nanocomposites comprising Nb₂O₅@Carbon core–shell nanoparticles (Nb₂O₅@C NPs) and reduced graphene oxide (rGO), and an analysis of their electrochemical performance with respect to various weight ratios of Nb₂O₅@C NPs to rGO (e.g., Nb₂O₅@C, Nb₂O₅@C/rGO‐70, ‐50, and ‐30). In a Na half‐cell configuration, the Nb₂O₅@C/rGO‐50 shows highly reversible capacity of ≈285 mA h g^?1 at 0.025 A g^?1 in the potential range of 0.01–3.0 V (vs Na/Na⁺). In addition, the Na‐HSC using the Nb₂O₅@C/rGO‐50 anode and activated carbon (MSP‐20) cathode delivers high energy/power densities (≈76 W h kg^?1 and ≈20 800 W kg^?1) with a stable cycle life in the potential range of 1.0–4.3 V. The energy and power densities of the Na‐HSC developed in this study are higher than those of similar Li‐ and Na‐HSCs previously reported.     

TiO2@Layered Double Hydroxide Core–Shell Nanospheres with Largely Enhanced Photocatalytic Activity Toward O2 Generation

TiO₂@CoAl‐layered double hydroxide (LDH) core–shell nanospheres are fabricated via hydrothermal synthesis of TiO₂ hollow nanospheres followed by in situ growth of CoAl‐LDH shell, which exhibit an extraordinarily high photocatalytic activity toward oxygen evolution from water oxidation. The O₂ generation rates of 2.34 and 2.24 mmol h^?1 g^?1 are achieved under full sunlight (>200 nm) and visible light (>420 nm), respectively, which are among the highest photocatalytic activities for oxygen production to date. The reason is attributed to the desirable incorporation of visible‐ light‐active LDH shell with UV light‐responsive TiO₂ core for promoted solar energy utilization. Most importantly, the combined experimental results and computational simulations reveal that the strong donor–acceptor coupling and suitable band matching between TiO₂ core and LDH shell facilitate the separation of photoinduced electron‐hole pairs, accounting for the highly efficient photocatalytic performance. Therefore, this work provides a facile and cost‐effective strategy for the design and fabrication of hierarchical semiconductor materials, which can be applied as photocatalyst toward water splitting and solar energy conversion.     

Nickel@Nickel Oxide Core–Shell Electrode with Significantly Boosted Reactivity for Ultrahigh‐Energy and Stable Aqueous Ni–Zn Battery

The main bottlenecks of aqueous rechargeable Ni–Zn batteries are their relatively low energy density and poor cycling stability, mainly arising from the low capacity and inferior reversibility of the current Ni‐based cathodes. Additionally, the complicated and difficult‐to‐scale preparation procedures of these cathodes are not promising for large‐scale energy storage. Here, a facile and cost‐effective ultrasonic‐assisted strategy is developed to efficiently activate commercial Ni foam as a robust cathode for a high‐energy and stable aqueous rechargeable Ni–Zn battery. 3D Ni@NiO core–shell electrode with remarkably boosted reactivity and an area of 300 cm² is readily obtained by this ultrasonic‐assisted activation method (denoted as SANF). Benefiting from the in situ formation of electrochemically active NiO and porous 3D structure with a large surface area, the as‐fabricated SANF//Zn battery presents ultrahigh capacity (0.422 mA h cm^?2) and excellent cycling durability (92.5% after 1800 cycles). Moreover, this aqueous rechargeable SANF//Zn battery achieves an impressive energy density of 15.1 mW h cm^?3 (0.754 mW h cm^?2) and a peak power density of 1392 mW cm^?3, outperforming most reported aqueous rechargeable energy‐storage devices. These findings may provide valuable insights into designing large‐scale and high‐performance 3D electrodes for aqueous rechargeable batteries.     

Formation Mechanism of Epitaxial Palladium–Platinum Core–Shell Nanocatalysts in a One‐Step Supercritical Synthesis

The scarcity of platinum group metals provides a strong incentive to optimize the catalytic activity and stability, e.g., through nanoalloys or core–shell nanoparticles. Here, time‐resolved X‐ray total scattering and transmission electron microscopy characterization are used to study the formation of palladium–platinum core–shell nanoparticles under solvothermal conditions. It is shown that Pd rapidly forms small (5–10 nm), disordered primary particles, which agglomerate and crystallize when reaching 20–25 nm. The primary Pd particles provide nucleation sites for Pt, and, with extended reaction time, the Pd cores become fully covered with Pt shells. The observed core–shell material is surprising when considering the Pt–Pd phase diagram and relative surface energies, but it can be rationalized through the kinetics of precursor conversion. To bridge the gap between scientific studies and industrial demand for large‐scale production, the synthesis process is successfully transferred to a continuous flow supercritical reactor providing a simple scalable and green process for production of bimetallic nanocatalysts.     

Synthesis of Au–CdS Core–Shell Hetero‐Nanorods with Efficient Exciton–Plasmon Interactions

The synthesis of large lattice mismatch metal‐semiconductor core–shell hetero‐nanostructures remains challenging, and thus the corresponding optical properties are seldom discussed. Here, we report the gold‐nanorod‐seeded growth of Au–CdS core–shell hetero‐nanorods by employing Ag₂S as an interim layer that favors CdS shell formation through a cation‐exchange process, and the subsequent CdS growth, which can form complete core–shell structures with controllable shell thickness. Exciton–plasmon interactions observed in the Au–CdS nanorods induce shell thickness‐tailored and red‐shifted longitudinal surface plasmon resonance and quenched CdS luminescence under ultraviolet light excitation. Furthermore, the Au–CdS nanorods demonstrate an enhanced and plasmon‐governed two‐photon luminescence under near‐infrared pulsed laser excitation. The approach has potential for the preparation of other metal‐semiconductor hetero‐nanomaterials with complete core–shell structures, and these Au–CdS nanorods may open up intriguing new possibilities at the interface of optics and electronics.     

π‐Extended Spiro Core‐Based Nonfullerene Electron‐Transporting Material for High‐Performance Perovskite Solar Cells

Electron transport materials (ETMs) play a significant role in perovskite solar cells (PSCs). However, conventional solution processable organic ETMs are mainly restricted to fullerene derivatives and it is challenging to obtain nonfullerene ETMs with satisfactory properties. In this work, a new organic semiconductor SPS‐4F is synthesized by utilizing the classical spiro[fluorine‐9′9‐thioxanthene] unit to construct a π‐extended core. Although spiro is normally used in hole transport materials, the new spiro derivative SPS‐4F is successfully used as an ETM in inverted PSCs with power conversion efficiency over 20%. In addition, SPS‐4F can strongly coordinate with MAPbI₃ perovskite and lead to efficient surface trap passivation. The resultant PSCs exhibit excellent stability in air because of the hydrophobic property of SPS‐4F. This work opens up opportunities to obtain a new family of ETMs based on spiro and paves a way to the fabrication of high‐performance PSCs with low cost.     

One‐Step All‐Solution‐Based Au–GO Core–Shell Nanosphere Active Layers in Nonvolatile ReRAM Devices

Nonvolatile resistive random‐access memory devices based on graphene‐oxide‐wrapped gold nanospheres (AuNS@GO) are fabricated following a one‐step room‐temperature solution‐process approach reported herein for the first time. The effect of the thickness of the GO layer (2, 5, and 7 nm) and the size of the synthesized AuNS (15 and 55 nm) are inspected. Reliable bistable switching is observed in the devices made from a flexible substrate and incorporating 5 and 7 nm thick GO‐wrapped AuNS, sandwiched between two metal electrodes. Current–voltage measurements show bipolar switching behavior with an ON/OFF ratio of 10³ and relatively low operating voltage (?2.5 V). The aforementioned devices unveil remarkable robustness over 100 endurance cycles and a retention of 10³ s. Conversely, a 2 nm thick GO layer is shown to be insufficient to allow current passage from the bottom to the top electrodes. The resistive switching mechanism is demonstrated by space charge trapped limited current due to the AuNS in AuNS@GO matrix. The proposed device and methodology herein applied are expected to be attractive candidates for future generation flexible memory devices.     

Organometal Halide Perovskite Solar Cells with Improved Thermal Stability via Grain Boundary Passivation Using a Molecular Additive

Organometal halide perovskite solar cells (PeSCs) are regarded as promising photovoltaics due to their outstanding power conversion efficiencies (PCEs). However, even though their PCEs are achieved over 20%, their intrinsically poor stability is a big bottleneck for their practical uses. Here, a simple method is reported using phenyl‐C₆₁‐butyric acid methyl ester as a molecular additive to improve thermal stability of organometal halide perovskite crystals, which also improves the PCEs of the associated PeSCs. Moreover, by varying the grain size of perovskite crystals up to ≈150 µm, it is demonstrated that grain boundary plays a significant role in their thermal stability. Cells with smaller grain interface area (i.e., larger grain size) have higher thermal stability. The additive is located at grain boundaries and found to induce electron transfer reactions with halogens in the perovskite. The reaction products chemically passivate perovskite crystals and strongly bind halogen atoms at grain boundaries to their crystal lattice, preventing them from exiting from the crystal lattice, which improves thermal stability of perovskite crystals. This study offers a simple method for improving thermal stability of perovskite without any loss and opens up the possibility of the use of various molecular additives to achieve highly stable PeSCs.