Double‐Wall Carbon Nanotube–Porphyrin Supramolecular Hybrid: Synthesis and Photophysical Studies

Double‐wall carbon nanotubes (DWCNTs) with pyridyl units covalently attached to the external wall through isoxazolino linkers and carboxylic groups that have been esterified by pentyl chains are synthesized. The properties of these modified DWCNTs are then compared with an analogous sample based on single‐wall carbon nanotubes (SWCNTs). Raman spectroscopy shows the presence of characteristic radial breathing mode vibrations, confirming that the samples partly retain the integrity of the nanotubes in the case of DWCNTs, including the internal and external nanotubes. Quantification of the pyridyl content for both samples (DWCNT and SWCNT derivatives) is based on X‐ray photoelectron spectroscopy and thermogravimetric profiles, showing very similar substituent load. Both pyridyl‐containing nanotubes (DWCNTs and SWCNTs) form a complex with zinc porphyrin (ZnP), as evidenced by the presence of two isosbestic points in the absorption spectra of the porphyrin upon addition of the pyridyl‐functionalized nanotubes. Supramolecular complexes based on pyridyl‐substituted DWCNTs and SWCNTs quench the emission and the triplet excited state identically, through an energy‐transfer mechanism based on pre‐assembly of the ground state. Thus, the presence of the intact inner wall in DWCNTs does not influence the quenching behavior, with respect to SWCNTs, for energy‐transfer quenching with excited ZnP. These results sharply contrast with previous ones referring to electron‐transfer quenching, in which the double‐wall morphology of the nanotubes has been shown to considerably reduce the lifetime of charge separation, owing to faster electron mobility in DWCNTs compared to SWCNTs.     

Electrochemistry of polystyrene intercalated vertically aligned single- and double-walled carbon nanotubes on gold electrodes

Electrochemical electrodes incorporating double- and single-walled carbon nanotubes (CNTs) were fabricated on cysteamine modified flat gold substrates. Through covalent coupling of the amine end groups with carboxyl functionalized CNTs, a dense forest of vertically aligned CNTs was produced. To these a 30 nm thick insulating polystyrene layer was spin coated, resulting in exposure of the uppermost carbon nanotube ends. The electrochemical performance of each electrode was then determined using the redox probe ruthenium hexaamine. Once surrounded by polymer, the double-walled CNTs (DWCNTs) showed an improved electron transfer rate, compared to the single-walled electrode. This improvement was attributed to the protection of the electronic properties of the inner wall of the DWCNT during the chemical modification and suggests that DWCNTs may offer a useful alternative to SWCNTs in future electrochemical sensors and biosensors.     

Electrochemical reduction of oxygen on double-walled carbon nanotube modified glassy carbon electrodes in acid and alkaline solutions

The oxygen reduction reaction has been investigated on double-walled carbon nanotube (DWCNT) modified glassy carbon (GC) electrodes in acid and alkaline media using the rotating disk electrode (RDE) method. The surface morphology and composition of DWCNT samples was examined by transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS). Aqueous suspensions of DWCNTs were prepared using Nafion and non-ionic surfactant Triton X-100 as dispersing agents. The RDE results indicated that the DWCNT modified GC electrodes are active catalysts for oxygen reduction in alkaline solution. In acid media DWCNT/GC electrodes possess poor electrocatalytic properties for O₂ reduction which indicates lack of metal catalyst impurities in the DWCNT material studied. The oxygen reduction behaviour of DWCNTs was similar to that of multi-walled carbon nanotubes (MWCNTs) observed in our previous studies.     

Field-effect characteristics and screening in double-walled carbon nanotube field-effect transistors

Field-effect transistors (FETs) have been fabricated using double-walled carbon nanotubes (DWCNTs), and electrical transport measurements have been carried out on 125 DWCNT FETs. Among these devices, 52 were found to show basically semiconducting field-effect characteristics, 44 show metallic characteristics, and 29 show neither pure semiconducting nor metallic characteristics. These 3 distinct types of field-effect characteristics were identified as resulting from the semiconducting (S)-S, metallic (M)-M or M-S, and S-M combinations of the two shells of the DWCNT. While the S-S and M-M or M-S DWCNT devices exhibit similar field-effect characteristics to those by single-walled carbon nanotube (SWCNT) devices, the S-M device responds uniquely to the external gate voltage. In particular, it was found that free charges in the inner metallic shell may screen the outer semiconducting shell from the gate effect and that the screening is directly related to the intershell interaction, which increases with increasing temperature and tube diameter. The screening is disadvantageous to the performance of DWCNT FETs, and a similar effect is expected to occur in MWCNTs.     

Bulk synthesis of linear carbon chains confined inside single-wall carbon nanotubes by vacuum discharge

Carbyne, an infinite carbon chain, has attracted much interest and induced significant controversy for many decades. Recently, the presence of linear carbon chains (LCCs), which were confined stably inside double-wall carbon nanotubes (DWCNTs) and multiwall carbon nanotubes (MWCNTs), has been reported. In this study, we present a novel method to produce LCCs in a film of carbon nanotubes (CNTs). Our transmission electron microscopy and Raman spectroscopy revealed the formation of a bulk amount of LCCs after electric discharge of CNT films, which were used as field emission cathodes. The LCCs were confined inside single-wall CNTs as well as DWCNTs. Furthermore, two or three LCCs in parallel with each other are encapsulated when the inner diameter of CNT is larger than approximately 1.1 nm.     

一种经氟化和热处理在双壁碳纳米管上生成缺陷的方法(英文)

Nanoscale defects in the outer tube to preserve the electrical and optical features of the inner tube can be engineered to exploit the intrinsic properties of double walled carbon nanotubes (DWCNTs) for various promising applications. We demonstrated a selective way to make defects in the outer tube by the fluorination of DWCNTs followed by the thermal detachment of the F atoms at 1000 °C in argon. Fluorinated DWCNTs with different amounts of F atoms were prepared by reacting with fluorine gas at 25, 200, and 400 °C that gave the stoichiometry of CF0.20, CF0.30, and CF0.43, respectively. At the three different temperatures used, we observed preservation of the coaxial morphology in the fluorinated DWCNTs. For the DWCNTs fluorinated at 25 and 200 °C, the strong radial breathing modes (RBMs) of the inner tube and weakened RBMs of the outer tube indicated selective fluorine attachment onto the outer tube. However, the disappearance of the RBMs in the Raman spectrum of the DWCNTs fluorinated at 400 °C showed the introduction of F atoms onto both inner and outer tubes. There was no significant change in the morphology and optical properties when the DWCNTs fluorinated at 25 and 200 °C were thermally treated at 1000 °C in argon. However, in the case of the DWCNTs fluorinated at 400 °C, the recovery of strong RBMs from the inner tube and weakened RBMs from the outer tube indicated the selective introduction of substantial defects on the outer tube while preserving the original tubular shape. The thermal detachment of F atoms from fluorinated DWCNTs is an efficient way to make highly defective outer tubes for preserving the electrical conduction and optical activity of the inner tubes.     

Molecular dynamics study of carbon nanotube oscillators revisited

We performed molecular dynamics simulation of double walled carbon nanotube (DWCNT) oscillators under constant energy and constant temperatures with various commensurations and nanotube lengths. We clarify and resolve questions and differences raised by previous simulation results of similar systems. At constant energy, sustained oscillation is available for a wide range of initial temperatures. But low initial temperature is advantageous for DWCNTs to sustain oscillation under constant energy. We observed sustained oscillation at constant energy for both commensurate and incommensurate DWCNTs. On the other hand, under constant temperatures, both high and low temperatures are disadvantageous to sustain DWCNT oscillations. At constant low temperature, neither commensurate nor incommensurate DWCNTs can maintain oscillation. At appropriate constant temperatures, the oscillatory behavior of incommensurate nanotubes is much more sustained than that of commensurate tubes. The oscillatory frequency of DWCNTs depends significantly on the length of tubes. The initial oscillatory frequency is inversely proportional to the DWCNT lengths. The oscillation frequency of DWCNTs is insensitive to the initial temperatures at constant energy, but slightly dependent on the temperature at constant temperatures.     

Theoretical study on the electronic structure nature of single and double walled carbon nanotubes and its role on the electron transport

Density functional theory and molecular dynamics (MD) calculations were used to evaluate electronic structure properties in a series of nanotubes with smallest possible diameters (both types: armchair and zigzag), and the corresponding chiral nanotubes (8,m) for 0 ≤ m ≤ 8. The calculations were performed considering a length of 16.5 Å. We evaluated a set of 26 combinations of dual nanotubes (armchair/armchair, zigzag/zigzag, armchair/zigzag, and zigzag/armchair), where the first label corresponds to the outer tube. We extended our study with nine additional systems of double-walled carbon nanotubes (DWCNT) with semiconductor nature. In this regard, we gave insight into the semiconductive or metallic nature inherited to the dual tubes. DWCNT systems were possible to construct by maintaining a radial distance of 3.392 Å for the armchair/armchair arrangement and 3.526 Å for the zigzag/zigzag type. It was considered as a reference, the interplanar distance of graphite (3.350 Å). Electronic transport calculations were also performed on selected DWCNT systems in order to understand the role played by the different symmetries under study. It was evidenced that the electronic structure nature of the systems rules the ability to transport electrons through the DWCNT interface.     

Fabrication of double-walled carbon nanotube counter electrodes for dye-sensitized solar sells

Double-walled carbon nanotubes (DWCNTs) have been studied for counter-electrode application in dye-sensitized solar cells (DSCs). Mesoporous TiO2 films are prepared from the commercial TiO2 nanopowders by screen-printing technique on optically transparent-conducting glasses. A metal-free organic dye (indoline dye D102) is used as a sensitizer. DWCNTs are applied to substitute for platinum as counter-electrode materials. Morphological and electrochemical properties of the formed counter electrodes are investigated by scanning electronic microscopy and electrochemical impedance spectroscopy, respectively. The electronic and ionic processes in platinum and DWCNT-based DSCs are analyzed and discussed. The catalytic activity and DSC performance of DWCNTs and Pt are compared. A conversion efficiency of 6.07% has been obtained for DWCNT counter-electrode DSCs. This efficiency is comparable to that of platinum counter-electrode-based devices.     

Enhanced photoluminescence from very thin double-wall carbon nanotubes synthesized by the zeolite-CCVD method

Photoluminescence (PL) from purified (>90%) double-wall carbon nanotubes (DWNTs), which have been synthesized by zeolite catalyst-supported chemical vapor deposition (zeolite-CCVD), of very small diameters (0.8-nm average inner tube) is reported. The PL contour mappings for various ratios (1-90%) of double- versus single-wall carbon nanotubes by thermal oxidation have enabled us to unambiguously identify the chirality of inner tubes for the DWNTs synthesized. After the extensive high-temperature oxidation at 700 degrees C, high-purity (>90%) DWNTs of approximately 0.8 nm inner diameter are obtained, and most of these correspond to the DWNTs having inner tubes with chiralities of (7,5), (7,6), and (9,4).     

Oxygen gas-induced lip-lip interactions on a double-walled carbon nanotube edge

We have investigated adsorption of an O(2) molecule on a double-walled carbon nanotube (DWCNT) edge using density functional theory calculations. An O(2) molecule adsorbs exothermally without an adsorption barrier at open nanotube edges that are energetically favorable with a large adsorption energy of about -9 eV in most cases. Dissociative adsorption of an O(2) molecule induces various spontaneous lip-lip interactions via the bridged carbon atoms, generating the closed tube ends. This explains why the DWCNTs are chemically more stable than the single-walled nanotubes during observed field emission experiments. The field emission takes place via the localized states of the bridged carbon atoms, not via those of the adsorbed oxygen atoms particularly in the armchair nanotubes. We also find that some O(2) precursor states exist as a bridge between tube edges.     

SiOx纳米管的制备及其发光特性

Amorphous SiOx nanotubes with homogeneous diameters were fabricated in large-scale on silicon substrate by thermal evaporation method, with liquid gallium as medium. The average diameter of tubes is about 80 nm and the length is more than 10 1m, with small ratio between the inner and outer diameter of the tube. The silicon element in the substrate and the residual oxygen element in reaction chamber were first dissolved into liquid Ga. Then the SiOx precipitated from the surface of gallium droplet, forming the nanotube structure with Ga droplet being the center. The room temperature photoluminescence measurements under excitation at 260 nm show that the SiOx nanotubes has a strong blue emission at 453 nm with two shoulders at 410 and 480 nm respectively, which may be related to oxygen defects. The preparation method improved the traditional complicated method and also provided a new way to fabricate SiOx nanotubes in large quantity.     

Probing charge transfer between shells of double-walled carbon nanotubes sorted by outer-wall electronic type

Double-walled carbon nanotubes (DWCNTs) with outer metallic (M) or semiconducting (S) shells were sorted by density-gradient ultracentrifugation and examined by Raman spectroscopy and in situ Raman spectroelectrochemistry. The combination of sorting and the selection of appropriate laser excitation energies allowed the disentanglement of the effects of different variations of the electronic type (M or S) of the inner and outer tubes in DWCNTs on the doping behavior and charge transfer between the inner and outer walls. Charge transfer from the outer tube to the inner tube occurs only if the electronic states of the outer tube are filled with electrons or holes, and if these filled states are higher in energy than those of the inner tube. Therefore, each combination of inner and outer tube (i.e., inner@outer: M@M, M@S, S@M, and S@S) exhibits a distinct behavior. The potential needed to observe the effects of charge transfer between the inner and outer tubes is found to increase in the following order: M@M < S@M < M@S < S@S.     

反渗透过程中双壁碳纳米管通水阻盐性能的分子动力学模拟

采用分子动力学模拟方法, 探究了非常规双壁碳纳米管(DWCNT)在反渗透过程中, 不同内外管间距对管道内水分子与盐离子运动行为的影响. 本文采用0.5 mol·L^-1氯化钠水溶液模拟海水, 内管始终采用CNT(8,8)型, 并对盐水层施加恒力模拟反渗透压. 重点考察盐离子数量分布与通水情况, 计算水分子平均力势, 并分析水分子氢键寿命与偶极矩分布. 结果表明, 管间距不仅影响上述各项性质, 还会改变盐离子与水分子在碳管中的渗透特性. 模拟结果显示, 小尺寸DWCNT可以有效实现盐水分离但水通量较小, 大尺寸DWCNT的水容量较大但阻盐效率不高, 而中尺寸DWCNT (即: 管间距为0.815 nm)则具有最佳的通水阻盐性能. 本文试图从分子层面揭示了DWCNT通水阻盐机理, 并为人们设计新型海水淡化渗透膜提供理论指导.     

The intermediate frequency modes of single- and double-walled carbon nanotubes: a Raman spectroscopic and in situ Raman spectroelectrochemical study

The intermediate frequency modes (IFM) of single-walled carbon nanotubes (SWCNTs) and double-walled carbon nanotubes (DWCNTs) were analyzed by Raman spectroscopy and in situ Raman spectroelectrochemistry. The inner and outer tubes of DWCNTs manifested themselves as distinct bands in the IFM region. This confirmed the diameter dependence of IFM frequencies. Furthermore, the analysis of inner tubes of DWCNTs allowed a more-precise assignment of the bands in the IFM region to features intrinsic for carbon nanotubes. Although the inner tubes in DWCNTs are assumed to be structurally perfect, the role of defects on IFM was discussed. The dependence of IFM on electrochemical charging was also studied. In situ spectroelectrochemical data provide a means to distinguish the bands of the outer and inner tubes.     

Optical and field emission properties of thin single-crystalline GaN nanowires

Thin high-quality gallium nitride (GaN) nanowires were synthesized by a catalytic chemical vapor deposition method. The synthesized GaN nanowires with hexagonal single-crystalline structure had thin diameters of 10-50 nm and lengths of tens of micrometers. The thin GaN nanowires revealed UV bands at 3.481 and 3.285 eV in low-temperature PL measurements due to the recombination of donor-bound excitons and donor-acceptor pairs, respectively. The blue shifts of UV bands in the low-temperature PL measurement were observed, indicating quantum confinement effects in the thin GaN nanowires which have smaller diameters than the exciton Bohr radius, 11 nm. For field emission properties of GaN nanowires, the turn-on field of GaN nanowires was 8.5 V/microm and the current density was about 0.2 mA/cm(2) at 17.5 V/microm, which is sufficient for the applications of field emission displays and vacuum microelectronic devices. Moreover, the GaN nanowires indicated stronger emission stability compared with carbon nanotubes.     

Self-Assembly of a Pyridine-Based Amphiphile Complexed with Regioisomeric Dihydroxy Naphthalenes into Supramolecular Nanotubes with Different Inner Diameters

A pyridine-based amphiphile complexed with 1,5-, 1,6-, 2,6-, or 2,7-dihydroxy naphthalene self-assembled in water to form nanotubes with inner diameters of 46, 38, 24, 18, and 11 nm in which the naphthalene molecules formed J-type aggregates. In contrast, the amphiphile complexed with 1,2-, 1,3-, 1,4-, 1,7-, 1,8-, or 2,3-dihydroxy naphthalene formed nanofibers in which the naphthalene molecules formed H-type aggregates. The inner diameter of the nanotubes strongly depended on the regioisomeric dihydroxy naphthalene. UV–vis, fluorescence, infrared spectroscopy, X-ray diffraction analysis, and differential scanning calorimetry showed that nanotubes with smaller inner diameters had weaker intermolecular hydrogen bonds between the tilted amphiphiles complexed with the naphthalene molecules within the membrane walls and showed larger Stokes shifts in the excimer fluorescence of the naphthalene moiety. These findings should be useful not only for fine-tuning the inner diameters of supramolecular nanotubes but also for controlling the aggregation states of functional aromatic molecules to generate nanostructures with useful optical and electronic properties in water.     

多壁碳纳米管储氢的物理吸附特性

The physisorption of hydrogen stored in armchair multi-walled carbon nanotubes (MWCNTs) is simulated by the grand canonical Monte Carlo (GCMC) method on the condition of 10 MPa at normalt emperature. Hydrogen-hydrogen and hydrogen-carbon interactions are both modeled with Lennard-Jones potential. The hydrogen storage in double-walled carbon-nanotubes (DWCNTs) has been investigated on the condition that the internal or external radius is changed while the other radius remains constant. The results show that hydrogen molecules are mostly absorbed near the tube walls, and the hydrogens to rage capacityisim proved effectively when the difference between the internal radius and the external radius increases from 0.34 to 0.61 or 0.88 nm. Its simple theoretic explanation also is given. Further more, the capacity of hydrogen physisorbed in there-walled carbon nanotubes (TWCNTs) is calculated when the wall-wall distance is 0.34, 0.61 and 0.88 nm respectively. Then its hydrogen storage capacity is compared with that of single-walled carbon nanotubes (SWCNTs) and DWCNTs, and it is discovered that the capacity of hydrogen physisorbed in MWCNTs decreases as the number of wall increases.     

Performance of dye-sensitized solar cells with various carbon nanotube counter electrodes

Double-wall carbon nanotubes (DWCNTs), single-wall carbon nanotubes (SWCNTs), and multi-wall carbon nanotubes (MWCNTs) were investigated as an alternative for platinum in counter-electrodes for dye-sensitized solar cells. The counter-electrodes were prepared on fluorine-doped tin oxide glass substrates by the screen printing technique from pastes of carbon nanotubes and organic binder. The solar cells were assembled from carbon nanotubes counter-electrodes and screen printed anodes made from titanium dioxide. The cells produced with DWCNTs, SWCNTs or MWCNTs have overall conversion efficiencies of 8.0%, 7.6% and 7.1%, respectively. Electrochemical impedance spectroscopy measurements revealed that DWCNTs displayed the highest catalytic activity for the reduction of tri-iodide ions. The large surface area and superior chemical stability of the DWCNTs facilitated the electron-transfer kinetics at the interface between counter-electrode and electrolyte and yielded the lowest transfer resistance, thereby improving the photovoltaic activity. A short-term stability test at moderate conditions confirmed the robustness of solar cells based on the use of DWCNTs, SWCNTs or MWCNTs.

Noncovalent functionalization of multiwalled and double‐walled carbon nanotubes: Positive effect of the filler functionalization on high glass transition temperature epoxy resins

Double‐walled carbon nanotubes (DWCNTs) and multiwalled carbon nanotubes (MWCNTs) were modified using melamine to attach ? NH₂ to the surface of these fillers, without previous oxidation of their graphene layers. FT‐Raman, elemental (chemical) and thermogravimetric analysis, confirmed the modification, which was more extensive for DWCNTs. The potential of this modification was evaluated by adding the melamin‐modified nanotubes to thermosets based on diglycidyl ether of bisphenol A (resin) and polycyclic amine (hardener). Broadening of the glass transition interval and an increase between 7 and 8 °C of the glass transition temperatures show better filler/matrix interaction for the nanocomposites based on melamine‐modified nanotubes. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1860–1868, 2009