Improvement of impact noise in a passenger car utilizing sound metric based on wavelet transform

A new sound metric for impact sound is developed based on the continuous wavelet transform (CWT), a useful tool for the analysis of non-stationary signals such as impact noise. Together with new metric, two other conventional sound metrics related to sound modulation and fluctuation are also considered. In all, three sound metrics are employed to develop impact sound quality indexes for several specific impact courses on the road. Impact sounds are evaluated subjectively by 25 jurors. The indexes are verified by comparing the correlation between the index output and results of a subjective evaluation based on a jury test. These indexes are successfully applied to an objective evaluation for improvement of the impact sound quality for cases where some parts of the suspension system of the test car are modified.     

Radiation characteristics of multiple and single sound hole vihuelas and a classical guitar

Two recently built vihuelas, quasi-replicas of the Spanish Renaissance guitar, one with a small body and one sound hole and one with a large body with five sound holes, together with a classical guitar are investigated. Frequency dependent radiation strengths are measured using a 128 microphone array, back-propagating the frequency dependent sound field upon the body surface. All three instruments have a strong sound hole radiation within the low frequency range. Here the five tone holes vihuela has a much wider frequency region of strong sound hole radiation up to about 500 Hz, whereas the single hole instruments only have strong sound hole radiations up to about 300 Hz due to the enlarged radiation area of the sound holes. The strong broadband radiation of the five sound hole vihuela up to about 500 Hz is also caused by the sound hole phases, showing very consistent in-phase relations up to this frequency range. Also the radiation strength of the sound holes placed nearer to the center of the sound box are much stronger than those near the ribs, pointing to a strong position dependency of sound hole to radiation strength. The Helmholtz resonance frequency of the five sound hole vihuela is influenced by this difference in radiation strength but not by the rosettas, which only have a slight effect on the Helmholtz frequency.     

双声源位置和强度识别的三维声强方法

目前在远场识别声源空间位置和强度缺乏行之有效的方法。针对此问题,提出采用四传声器进行三维声强测量,从而构建出声强、声源坐标和声功率的非车线性方程组,求解方程得出声源空间坐标和强度的方法。以3个三维声强探头对两个同频率单极子声源的识别为例,分别利用数值仿真和半消声室内的实验进行方法验证,并对声源的识别空间分辨率做了测试,得出角度识别最大误差为3.83°,为真实值的8.5%,距离识别最大误差0.1 m,为真实距离的10%。结果表明采用该方法空间坐标和声功率识别均具有很高的准确度,双声源的空间位置分辨力也优于远场声全息方法。      

A method to predict the transmission of sound through corridors

This paper describes research carried out to provide a method by means of which sound levels in rooms adjacent to a corridor, produced by the transmission of sound through the corridor from another room, can be predicted. This has been done by using an acoustic scale model to show how the physical parameters of the corridor affect the transmission of sound into, out of and along the corridor. From analysis of the experimental results, empirical formulae are obtained to predict: (1) sound levels along a corridor produced by a sound source in the corridor or an adjacent room, (2) sound levels along a side corridor produced by a sound source in the main corridor and (3) sound levels in rooms adjacent to the corridor produced by a sound source in another room.     

环境因素对海-气界面低频异常声透射的影响研究

针对海中声源在海-气界面低频异常声透射问题, 根据两层媒质声传输模型, 分析了大气声速和密度与气压、气温、湿度及海水中声速和密度与海温、盐度间的关系, 研究了低频声透射和传输受温度、气压、盐度、湿度等因素的影响, 分析了各因素对声透射和传输的影响程度. 结果表明: 1) 声透射到大气中的声功率与气温、湿度负相关, 与海温、盐度、气压正相关; 2) 单极子与水平偶极子声源辐射到海中的声功率与海温、盐度负相关, 而垂直偶极子声源辐射到海中的声功率与海温、盐度正相关; 3) 声透射指向性与海温正相关, 与气温负相关; 4) 低频声透射受温度影响最大, 其次是盐度, 受气压和湿度影响较小, 垂直偶极子声源的声透射受温度影响大于水平偶极子和单极子声源.     

有限长线声源斜面声场分析

为了进一步研究有限长线声源的声场特性,完善有限长线声源声场理论,建立了有限长线声源斜面声场的模型,提出了其理论计算方法。基于仿真结果和数据分析,探讨并得到了有限长线声源斜面声场特性的三个参数与斜面声场特性之间的关系。通过调整斜面倾角α、交点的位置r0以及有限长线声源的长度L,可以有效改善斜面声场的分布。     

马铁菊头蝠声道声学特性的数值分析

采用有限元数值计算得到了马铁菊头蝠声道内部的声场分布,给出了马铁菊头蝠声道内几种特殊的腔体结构在蝙蝠发声过程中的作用。通过微型CT扫描并经过三维重构得到了马铁菊头蝠声道的三维立体模型用于有限元数值计算,通过在声门处放置单位声源计算得到了整个声道内部以及鼻孔周围的声压分布。结果表明,马铁菊头蝠声道包含了鼻腔结构后声波在声门上方的声压幅度明显大于不含鼻腔结构的情况,从传输曲线来看,声门上方鼻腔的存在使得系统对声波传输在二次谐波频率处呈现低阻抗效果,同时鼻腔的改变还可影响二次谐波的位置。而声门下方的气管空腔主要影响声波的背向转播,声门下方的气管空腔的存在可明显降低蝙蝠发声时声场在声道声门下方的声压幅度,同时抑制声音背向传播时二次谐波成分的强度。      

Illumination of the shadow zone in a two-channel oceanic waveguide with a fine structure of sound speed inhomogeneities

The experimental data on the sound field structure, which were obtained by emitting a continuous pseudonoise signal (a midfrequency of 3.2 kHz) in a two-channel oceanic waveguide, are compared with the calculations performed by the wave program with allowance for the fine structure of the sound speed inhomogeneities. A considerable increase in the intensity of the sound field with a definite angular spectrum is observed in the upper channel in the first shadow zone, and, in the experiment, the increase begins nearer to the sound source than predicted by the wave and ray calculations for a smooth sound speed profile. These features of the field structure are explained by the illumination of the shadow zone by the regular scattering of signals from highly anisotropic fine-structure inhomogeneities of the sound speed profile, which are clearly pronounced in the region of the given oceanic experiment.     

Experimental study of the influence of annular nozzle on acoustic characteristics of detonation sound wave generated by pulse detonation engine

Acoustic characteristics of the detonation sound wave generated by a pulse detonation engine with an annular nozzle, including peak sound pressure, directivity, and A duration, are experimentally investigated while utilizing gasoline as fuel and oxygen-enriched air as oxidizer. Three annular nozzle geometries are evaluated by varying the ratio of inner cone diameter to detonation tube exit diameter from 0.36 to 0.68. The experimental results show that the annular nozzles have a significant effect on the acoustic characteristics of the detonation sound wave. The annular nozzles can amplify the peak sound pressure of the detonation sound wave at 90° while reducing it at 0° and 30°. The directivity angle of the detonation sound wave is changed by annular nozzles from 30° to 90°. The A duration of the detonation sound wave at 90° is also increased by the annular nozzles. These changes indicate that the annular nozzles have an important influence on the acoustic energy distribution of the detonation sound wave, which amplify the acoustic energy in a direction perpendicular to the tube axis and weaken it along the direction of the tube axis.     

Vertical variability of sound fields produced by underwater explosions at difference distances from the source

To determine the spatial variability of sound fields in the Black Sea, correlation of multipath signals received by vertically separated hydrophones is investigated. The signals are produced by underwater explosions of trinitrotoluene charges. Dependence of the sound field variability on the distance to the source of sound is analyzed for the case of the corresponding points positioned near the sound channel axis. Conditions necessary for estimating the distance to the pulsed sound source are considered. Results of full-scale experiments in the Black Sea are presented and compared with the data obtained from the experiments in the Pacific Ocean near Kamchatka.     

虚拟声技术及其应用(上)

本文综述了虚拟声技术及其应用。在简单回顾了有关虚拟声的心理声学基础后，论述和分析了耳机和扬声器重发虚拟声的基本原理和基本的缺陷，总结了近年所提出的虚拟声的改进方法，最后探讨了虚拟声在科学研究、工程技术和消费电子领域的各种应用。     

管束穿孔板的管腔耦合共振吸声机理研究

为了揭示管束穿孔板共振吸声结构的吸声机理,利用热黏性条件下基于有限元算法的管束穿孔板仿真模型,研究了平面声波正入射条件下,管束穿孔板内部声场分布特征,并利用阻抗管对吸声系数的理论仿真结果进行了试验验证.结果表明,管束穿孔板在低频主要靠腔体共振吸声,在高频主要靠管共振吸声,管束穿孔板整体呈现出较为明显的管腔耦合共振吸声特征。管束穿孔板共振时管中声强和质点法向振速较大,高频次吸声峰频点处管中和腔中均有驻波形成,频率越高驻波数量越多.管束穿孔板的耦合共振受到管长、腔深、穿孔率和管内径等参数变化的影响,管长对高频耦合共振的影响最大,管长增大使高频主吸声峰频点移向低频,并使相邻主吸声峰之间的间距减小.      

Sound field separating on arbitrary surfaces enclosing a sound scatterer based on combined integral equations

To eliminate the limitations of the conventional sound field separation methods which are only applicable to regular surfaces, a sound field separation method based on combined integral equations is proposed to separate sound fields directly in the spatial domain. In virtue of the Helmholtz integral equations for the incident and scattering fields outside a sound scatterer, combined integral equations are derived for sound field separation, which build the quantitative relationship between the sound fields on two arbitrary separation surfaces enclosing the sound scatterer. Through boundary element discretization of the two surfaces, corresponding systems of linear equations are obtained for practical application. Numerical simulations are performed for sound field separation on different shaped surfaces. The influences induced by the aspect ratio of the separation surfaces and the signal noise in the measurement data are also investigated. The separated incident and scattering sound fields agree well with the original corresponding fields described by analytical expressions, which validates the effectiveness and accuracy of the combined integral equations based separation method.     

微穿孔板吸声结构水下应用研究

马大猷教授提出的微穿孔板吸声结构在空气噪声降低和隔离方面得到了广泛的应用,但未见水下应用的相关研究和报道。本文将空气中微穿孔板理论应用到水中,得到了水下微穿孔板吸声结构的吸声公式。通过理论分析,得出了微穿孔板结构直接应用于水中无法获得宽频吸收的结论。提出了通过匹配液将微穿孔板间接应用到水下的设想。设计了单层板和双层板吸声结构,并对它们的吸声特性进行了理论分析与仿真。结果表明,本文设计的微穿孔板吸声结构在水中能够获得优于空气中的宽频带吸声效果。实验测量了自制的微穿孔板吸声结构,吸声系数的测量值与理论曲线基本吻合,从而验证了理论分析的正确性。     

线阵波束形成声强缩放方法估算声源的辐射声功率

为了解决波束形成声源识别过程中声源辐射声功率定量计算的问题,给出了阵型简洁、便于组合的线阵声强缩放模型。通过推导线阵的声强缩放系数,建立起线阵波束输出结果与声源辐射声功率之间的换算关系。无论是线阵还是平面阵的声强缩放方法,对于偏离阵列中心位置较远处的声源进行辐射声功率估算时都存在较为明显的误差。通过理论推导和仿真模拟计算,研究了同一单极子点声源在不同位置处的声功率估算偏差随频率、幅度的变化规律,发现该估算偏差只与声源偏离位置有关,而与声源自身的强度信息无关的结论,据此给出了相应的声功率估算修正方法。半消声室实验结果和声压法测量结果对比表明:修正后的线阵声强缩放方法用于中高频声源的辐射声功率计算时,单频声源的估算误差不超过1.0 dB,宽带声源的估算误差不超过1.8 dB。      

热疗用环形平面换能器声场特性的研究

引入负声源，导出了环形平面换能器声场的简洁表示式，计算了单个圆环、多个同心圆环同时激励及环阵相控聚焦声源产生的声场，分析了环的宽度、环数及聚焦点位置等因素对声场特征的影响。提出根据各阵元在声场中某点产生的声压的相位来确定各阵元电激励信号的延时，此方法较根据各阵元到该点的平均声程确定各阵元电激励信号的延时，能更难确地在该点实现聚焦。     

水下隔声结构设计及评价方法

为使用混响法快捷地测量水下结构物的辐射噪声,需基于港口或海岸建造海上混响水池。针对内外都是水情况下的海上混响水池壁面隔声问题,设计了一种带梁空气夹层板水下隔声结构,通过仿真比较了不同参数的空气夹层板的隔声性能。为评价声波无规入射情况下水下大尺寸隔声结构隔声性能,提出了一种混响评价方法,通过隔声实验比较了混响法与脉冲法的不同。结果表明：带梁空气夹层板的水下隔声性能优异,声波无规入射情况下,面板厚度0.015 m、空气层厚度0.020 m的带梁空气夹层板在2～10 kHz频段插入损失大于20 dB;混响法可以有效评价大尺寸水下隔声结构的平均隔声性能,其反映的声波无规入射的平均隔声性能更接近于实际应用情况。     

On the metrology of the speed of sound in liquids

Decentralization of the standards base in measuring the speed of sound in liquids by expressing the speed of sound in fractions of the speed of light in vacuum is considered. A method to take into account the diffraction effects by measuring the speed of sound in the case of a constant acoustic wavelength and binding the absolute speed of sound values to the calculated thermodynamic values obtained by the nonacoustical method when the adiabatic compressibility is equal to the isothermal one is proposed. Errors of the reproducibility of the unit of the speed of sound in water using the proposed method are estimated.     

Contribution to the nonlinear theory of sound and hydrodynamic turbulence of a compressible liquid

The interaction of sound with hydrodynamic turbulence has been studied in detail. The sound absorption decrement, the correlation time and length and the frequency diffusion coefficient for the acoustic wave packet are calculated. The spectral composition of the sound radiated by a unit, turbulent volume and the spectral energy density of sound in equilibrium with the turbulence are studied. The region of applicability of the kinetic equation for sound with a linear dispersion low is found.     

Sound pressure minimization by adjusting the active source parameters with the use of a hybrid genetic algorithm

Results of computer experiments on the propagation and interaction of sound waves with the aim to minimize the sound pressure in a given zone of a rectangular region are presented. The sound pressure is minimized by the active action of additional sound sources positioned within the region of computation. The optimum parameters of active sources and their positions are determined by solving the minimization problem for the integral functional that expresses the average sound pressure in the given zone of the rectangular region. The problem is solved using a hybrid genetic algorithm.