Linear and nonlinear optical properties of Au/SiO2 nanocomposite prepared by P123

Mesoporous silica thin films loaded with gold nanoparticles are synthesized in the presence of EO20PO70EO20（P123）.Transmission electron microscope images show that the matrix of the nanocomposite is an ordered porous structure with a two-dimensional hexagonal phase.The wide-angle X-ray diffraction pattern implies that the nanocomposite contains gold crystals.These metallic nanoparticleembedded solid thin films show some linear and nonlinear optical properties due to their special structure and composition.Gold nanoparticles bring about surface plasmon resonance,and an absorption peak stemming from this effect has been observed.The linear absorption property is analyzed by a quantum mechanism,and the results show that it is influenced by the size and volume fraction of gold nanoparticles. Furthermore,it shows an obviously clear nonlinear optical property measured by the z-scan technique.The magnitude of the nonlinear refractive index of the nanocomposite is estimated to be about 10？ 10 cm 2 /W.     

Rapid microwave-assisted synthesis and electrochemical characterization of gold/carbon nanotube composites

Hybrid nanostructures composed of gold nanoparticles (NPs) and carbon nanotubes (CNTs) have been prepared by a microwave-assisted method in the mixed solvents of oleylamine and oleic. The morphology, structure and composition of as-obtained Au/CNT composites are characterized by transmission electron microscopy (TEM), energy dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD). The composites show characteristic plasmon absorption of Au NPs in the Ultraviolet–visual spectrum. Fourier transform infrared spectrum shows the successful introduction of functional groups on the surface of CNTs, which are crucial factors to assist the nucleation in situ of Au NPs on the surface of CNTs. Electrochemical measurements show the enhancement electrochemical response for the gold electrode modified with Au/CNT composites.     

Synthesis and characterization of cobalt/gold bimetallic nanoparticles

Cobalt/gold (Co/Au) bimetallic nanoparticles are prepared by chemically reducing gold (III) chloride to gold in the presence of pre-synthesized Co nanoparticles. Transmission electron microscopy (TEM), ultraviolet-visible (UV-vis) absorption spectrometry, and a superconducting quantum interference device (SQUID) magnetometer have been used to characterize as-prepared bimetallic nanoparticles. Our findings demonstrate Au not only grows onto Co nanoparticles, forming a surface coating, but also diffuses into Co nanoparticles. The introduction of Au alters the crystalline structure of Co nanoparticles and changes their magnetic properties. Dodecanethiols induce a reorganization of as-prepared Co/Au bimetallic nanoparticles.     

磁控溅射法制备金团簇纳米颗粒及性能表征

 采用磁控溅射法制备金团簇纳米颗粒,用透射电镜(TEM)、X射线衍射(XRD)、紫外可见光分光光度计(UV-Vis)和X射线光电子能谱(XPS)等分析手段对其表征,研究了金团簇纳米颗粒的形貌、颗粒度、结构、光吸收性质及物质成份。研究结果表明：制备的金团簇纳米颗粒呈球形,平均粒径在10 nm左右,粒径分布均匀,无团聚、氧化现象,颗粒的结构为面心立方。在519 nm处出现团簇颗粒的表面等离子共振吸收峰,测试得到Au(4f_7/2)和Au(4f_5/2)电子的结合能分别为83.3 eV和86.9 eV,并且没有出现金的氧化产物。     

Structural change of mesoporous silica with sonochemically prepared gold nanoparticles in its pores

Ultrasonic irradiation of mesoporous silica soaked in a mixture of chloroauric acid and isopropanol for 120 min in Ar atmosphere at room temperature yielded Au/SiO₂ mesoporous composite, which was characterized by high resolution transmission electron microscopy and optical absorption measurement. The structure of mesoporous silica after sonochemical preparation of gold (Au) nanoparticles within its pores was studied by nitrogen adsorption technique. It has been shown that the structural parameters, such as specific surface area (SSA), porosity (P), the mean pore diameter (l_p) were increased significantly after ultrasonic irradiation. It is suggested that the collision of Au nanoparticles with pore walls and localized erosion induced by the asymmetric implosive collapse of cavities on the extensive liquid–solid interface that are responsible for the structural change in the mesoporous solid.     

(Au,Si)/SiO2复合纳米颗粒薄膜的光谱特性

采用复合靶共溅射法制备了(Au，Si)／SiO2复合纳米颗粒薄膜样品，并对其荧光谱作了测量．在理论上分别计算了在强限域效应下和弱限域效应下Si纳晶吸收光谱的峰值位置与晶粒尺寸之间的关系，并采用Drude理论计算了Au／SiO2复合体系的吸收峰的峰值位置与微粒尺寸的关系．给出了(Au，Si)／SiO2体系复合薄膜共振吸收峰的位置随Au和Si的掺杂浓度比和微粒尺寸的相关特征．     

One-step synthesis of silica-coated magnetite nanoparticles by electrooxidation of iron in sodium silicate solution

In the present study, solid-solution gold?Cplatinum (Au?CPt) nanoparticles with controllable compositions were fabricated by high-intensity femtosecond laser irradiation of an aqueous solution of gold and platinum ions without any chemicals and complicated processes. Transmittance electron microscopy revealed that the single nanometer-sized particles were fabricated by femtosecond laser irradiation of mixed aqueous solutions of gold and platinum ions. The crystalline structure of nanoparticles was characterized by electron and X-ray diffractions. Contrary to the bulk Au?CPt binary systems, which commonly contain a pair of diffraction peaks between pure gold and platinum peaks because of its large miscibility gap in phase diagram, or mixture of Au and Pt, the diffraction peaks of Au?CPt nanoparticles fabricated in the experiment showed a characteristic of the fcc-type lattice. Moreover, the diffraction patterns shifted monotonically from the peak position of pure gold to that of pure platinum as the fractions of platinum ions in the solution were increased. These observations strongly imply that the Au?CPt nanoparticles were solid solution with intended compositions. This technique is not only simple and environmentally friendly, but also applicable to other binary and ternary systems.     

Nanocomposite ZnO/Au formation by pulsed laser irradiation

The ZnO/Au nanocomposite formation involves synthesis of Au and ZnO colloidal solutions by 532 nm pulse laser ablation of metal targets in deionized water followed by laser irradiation of the mixed colloidal solution. The transmission electron microscope (TEM) and high-resolution transmission electron microscope (HRTEM) images show evolution of spherical particles into ZnO/Au nanonetworks with irradiation time. The formation mechanism of the nanonetwork can be explained on the basis of near resonance absorption of 532 nm irradiation by gold nanoparticles which can cause selective melting and fusion of gold nanoparticles to form network. The ZnO/Au nanocomposites show blue shift in the ZnO exciton absorption and red shift in the Au plasmon resonance absorption due to interfacial charge transfer.     

Size control synthesis of starch capped-gold nanoparticles

Metallic gold nanoparticles have been synthesized by the reduction of chloroaurate anions [AuCl₄]⁻ solution with hydrazine in the aqueous starch and ethylene glycol solution at room temperature and at atmospheric pressure. The characterization of synthesized gold nanoparticles by UV–vis spectroscopy, high resolution transmission electron microscopy (HRTEM), electron diffraction analysis, X-ray diffraction (XRD), and X-rays photoelectron spectroscopy (XPS) indicate that average size of pure gold nanoparticles is 3.5 nm, they are spherical in shape and are pure metallic gold. The concentration effects of [AuCl₄]⁻ anions, starch, ethylene glycol, and hydrazine, on particle size, were investigated, and the stabilization mechanism of Au nanoparticles by starch polymer molecules was also studied by FT-IR and thermogravimetric analysis (TGA). FT-IR and TGA analysis shows that hydroxyl groups of starch are responsible of capping and stabilizing gold nanoparticles. The UV–vis spectrum of these samples shows that there is blue shift in surface plasmon resonance peak with decrease in particle size due to the quantum confinement effect, a supporting evidence of formation of gold nanoparticles and this shift remains stable even after 3 months.     

Ambient effect on optical absorption of Au nanoparticles dispersed within pores of mesoporous SiO2

A gold nanoparticles/monolithic mesoporous silica assembly was synthesized by ultrasonic irradiation of monolithic porous silica presoaked with precursor solution. Subsequent exposure to ambient air (ageing) and then drying at 120°C induce a new optical absorption peak around 470?nm (falling into the range from 460 to 475?nm) which is stable at room temperature, in addition to the normal surface plasmon resonance (SPR) of Au nanoparticles. Further drying results in the decline and disappearance of this peak, accompanied by increase of the normal SPR. If the sample, in which the new peak has disappeared due to long drying at 120°C, is exposed to the ambience once more, this peak will appear again after subsequent drying at 120°C, showing reversibility. Further experiments indicate that ambient ageing for a certain time plays a crucial role in the appearance of the new peak after subsequent drying at 120°C. Increased ageing time increases this peak. In addition, the ambient relative humidity and temperature during exposure are also important to the appearance of this peak. This peak may be associated with Au clusters with a size less than 1.5?nm. Based on the porous structure of the assembly and hydrophilicity of its pore wall, a nanodroplet formation and evaporation model is presented which can well explain all evolution behaviours of this peak. The model predicts the existence of the peak at 470?nm in the Au/silica assembly prepared by methods other than ultrasonic irradiation, which has also been confirmed by further experiments.     

One-pot synthesis of gold/poly(3,4-ethylendioxythiophene) nanocomposite

In this paper, we report the preparation of highly stable gold nanoparticles/poly(3,4-ethylendioxythiophene) nanocomposites by a one-pot chemical route in aqueous medium without surfactants to increase the solubility of the monomer (3,4-ethylendioxythiophene, EDOT) or to stabilize gold nanoparticles (Au NPs). The generation of the nanocomposite was followed by UV–Visible transmission spectroscopy combined with multivariate curve resolution alternating least squares analysis to deconvolute the individual spectra of the different species generated in the synthesis: oligomers, polymer and gold nanoparticles. The plasmon band observed at 530 nm during the synthesis step indicates the generation of gold nanoparticles. The influence of monomer and metal precursor concentration and their concentration ratios on Au NP size were analyzed. The electrochromic properties of the composite were investigated by UV–Visible absorption spectroelectrochemistry, being mainly related to polymer oxidation and reduction. The main difference observed is the hypsochromic shift of the polymer spectra due to the gold nanoparticles inside the polymer. Multicyclic spectroelectrochemical experiments evidence a high stability and adhesion of the nanocomposite.     

A novel method to prepare Au nanocage@SiO_2 nanoparticle

Gold （Au） nanocage@SiO2 nanoparticles are prepared by a novel approach. The silver （Ag） nanocube@SiO2 structure is synthetized firstly. Next, the method of etching a SiO2 shell by boiling water is adopted to change the penetration rate of AuCl4- through the SiO2 shell. AuCl4- can penetrate through silica shells of different thickness values to react with the Ag nanocube core by changing the incubation time. The surface plasma resonance （SPR） peak of synthetic Au nanocage@SiO2 can be easily tuned into the near-infrared region. Besides, CdTeS quantum dots （QDs） are successfully connected to the surface of Au nanocage@SiO2, which testifies that the incubation process does not change the property of silica.     

磁控溅射法制备金团簇纳米颗粒及性能表征

采用磁控溅射法制备金团簇纳米颗粒,用透射电镜(TEM)、X射线衍射(XRD)、紫外可见光分光光度计(UV-Vis)和X射线光电子能谱(XPS)等分析手段对其表征,研究了金团簇纳米颗粒的形貌、颗粒度、结构、光吸收性质及物质成份。研究结果表明：制备的金团簇纳米颗粒呈球形,平均粒径在10 nm左右,粒径分布均匀,无团聚、氧化现象,颗粒的结构为面心立方。在519 nm处出现团簇颗粒的表面等离子共振吸收峰,测试得到Au(4f7/2)和Au(4f5/2)电子的结合能分别为83.3 eV和86.9 eV,并且没有出现金的氧化产物。     

Synthesis and characterization of composite Au/TiO2 nanoparticles by laser irradiation

Composite Au/TiO₂ nanoparticles were synthesized by laser ablation of gold plate in TiO₂ sol. The nanoparticles were characterized by UV-visible spectroscopy, transmission electron microscopy, X-ray diffraction, and atomic force microscopy. The peak of surface plasmon is at 550 nm with a red shift of 30 nm compared with that of Au nanoparticles in water. Monolayers of composite Au/TiO₂ nanoparticles were obtained by dip-coating technique. The XRD pattern of Au/TiO₂ powders resembles a mixture of anatase TiO₂ and gold.     

Fabrication and characterization of Au/SiO2 nanocomposite films grown by radio-frequency cosputtering

Au/SiO₂ nanocomposite films were prepared on Si wafers by cosputtering of SiO₂ and gold wires. Au/Si atomic ratios in Au/SiO₂ nanocomposite films were varied from 0.53 to 0.92 by controlling the length of gold wire to study the evolution of the crystallization of gold, the size of Au/SiO₂ nanocomposite particles, and the optical properties of as-deposited Au/SiO₂ nanocomposite films. An X-ray photoelectron spectroscopy reveals that Au exists as a metallic phase in the bulk of SiO₂ matrix. Dome-shaped Au/SiO₂ nanocomposite particles and both Au (1 1 1) and (2 0 0) planes were observed in a field-emission scanning electron microscopy and X-ray diffraction studies respectively. With an ultraviolet-visible, absorption peaks of Au/SiO₂ nanocomposite films were observed at 525 nm.     

A facile strategy to synthesize bimetallic Au/Ag nanocomposite film by layer-by-layer assembly technique

A facile strategy has been developed for the preparation of bimetallic gold–silver (Au–Ag) nanocomposite films by alternating absorption of poly-(ethyleneimine)–silver ions and Au onto substrates and subsequent reduction of the silver ions. The composition, micro-structure and properties of the {PEI–Ag/Au}_n nanocomposite films were characterized by ultraviolet visible spectroscopy (UV–vis), transmisson electron microscopy (TEM), field emission scanning electron microscopy (FESEM), X-ray photoelectron spectroscopy (XPS), surface enhanced Raman scattering (SERS) and cyclic voltammetry (CV). The UV–vis characteristic absorbances of {PEI–Ag/Au}_n nanocomposite thin film increase almost linear with the number of bilayers, which indicates a process of uniform assembling. Appearance of a double plasmon bands in the visible region and the lack of apparent core–shell structures in the TEM images confirm the formation of bimetallic Au–Ag nanoparticles. The result of XPS also demonstrates the existence of Ag and Au nanoparticles in the nanocomposite films. TEM and FESEM images show that these Ag and Au nanoparticles in the films possess sphere structure with the size of 20–25 nm. The resulting {PEI–Ag/Au}_n films inherit the properties from both the metal Ag and Au, which exhibits a unique performance in SERS and electrocatalytic activities to the oxidation of dopamine. As a result, the {PEI–Ag/Au}_n films are more attractive compared to {PEI–Ag/PSS}_n and {PEI/Au}_n films.     

不同粒径、超均匀球形金纳米粒子合成及其表面增强拉曼散射效应研究

以氯金酸为原料,抗坏血酸为还原剂,柠檬酸钠为保护剂,用化学还原(种子生长)法制备了不同粒径、超均匀的球形金纳米粒子溶胶,并通过紫外可见吸收光谱(UV-Vis)和扫描电子显微镜(SEM)进行表征。结果表明,随着金纳米粒子粒径的增大,其UV-Vis光谱中的吸收峰发生红移并出现四极峰。为进一步研究金纳米粒子表面增强拉曼散射(SERS)效应的作用机理并优化其灵敏度,我们以罗丹明6G(R6G)为探针分子,对不同粒径的金纳米粒子进行SERS表征,发现R6G的SERS信号随着金纳米粒子的增大先增强后减弱。当金纳米粒子的平均粒径达到120 nm时,产生最强SERS信号增强,增强因子约为1.1×107。三维时域有限差分法(3D-FDTD)理论模拟纳米粒子阵列电磁场分布结果与实验数据的趋势一致。     

Au@碳球复合结构中Au颗粒位置调控光吸收

采用时域有限差分（FDTD）法研究Au纳米颗粒@碳球（AuNPs@CS）复合结构的光吸收控制。发现Au纳米颗粒@碳球复合结构中Au颗粒的位置可以控制复合结构光吸收。模型计算中选取两粒Au纳米颗粒以最佳深度（0 nm）嵌入碳球表面。当两粒Au颗粒球心与碳球球心夹角为22.5°和45°时,复合结构光吸收较单一碳球光吸收明显增强;当夹角为315°、270°、180°、90°时,光吸收增量逐渐减小;当夹角为337.5°时,光吸收量低于单一碳球。这一结果主要归因于Au纳米颗粒位置变化可引起表面等离子体光强度和光散射方向的变化。改变碳球表面Au纳米颗粒的数量和位置,可以进一步调节AuNPs@CS复合结构的光吸收。     

A simple and effective route for the preparation of poly(vinylalcohol) (PVA) nanofibers containing gold nanoparticles by electrospinning method

Poly(vinylalcohol) (PVA) nanofibers containing gold nanoparticles have been simply obtained by electrospinning a solution containing gold nanoparticles without the additional step of introducing other stabilizing agents. The optical property of gold nanoparticles in PVA aqueous solution was observed by UV-visible absorption spectra. Morphology of the Au/PVA nanofibers and distribution of the gold nanoparticles were characterized by transmission electron microscopy (TEM). The structure transformation was characterized from PVA to PVA/Au composite by Fourier transform infrared spectroscopy (FTIR).     

The characteristics of Au:VO2 nanocomposite thin film for photo-electricity applications

Au nanoparticles have been fabricated on normal glass substrates using nanosphere lithography (NSL) method. Vanadium dioxide has been deposited on Au/glass by reactive radio frequency (rf) magnetron sputtering. The structure and composition were determined by X-ray diffraction and X-ray photoelectron spectroscope. Electrical and optical properties of bare VO₂ and Au:VO₂ nanocomposite thin films were measured. Typical hysteresis behavior and sharp phase transition were observed. Nanopartical Au could effectively reduce the transition temperature to 40 °C. The transmittance spectrum for both Au:VO₂ nanocomposite thin film shows high transmittance under transition temperature and low transmittance above transition temperature. The characteristics present the Au:VO₂ nanocomposite thin film can be used for applications, such as “smart window” or “laser protector”.