钙黄绿素-Al3+荧光光谱法测定F-

报道了F-的荧光光谱测定法.在pH=8.9的缓冲液中,加入Al3 与荧光试剂钙黄绿素反应导致荧光猝灭,而再加入F-后,则F-与Al3 形成比钙黄绿素-Al3 更稳定的配合物,从而使钙黄绿素游离出来而使体系荧光增强,其荧光的增强与F-浓度在1.0×10-4-1.0×10-3mol/L范围内有较好的线性关系,据此可间接测定F-含量.     

盐酸川芎嗪的荧光光谱研究及应用

在 p H6— 10的水溶液中 ,盐酸川芎嗪产生稳定的荧光。最佳激发波长与发射波长分别为 2 95nm和335nm,当盐酸川芎嗪浓度为 5.0× 10 -6— 5.0× 10 -5mol/ L时 ,荧光强度与浓度有良好的线性关系。据此建立了荧光光度法直接测定盐酸川芎嗪注射液中盐酸川芎嗪含量的方法 ,该方法的相对标准偏差为3.51% ,检出下限为 1.0× 10 -6mol/ L。     

Meso-5,10,15,20-四(4-甲氧基苯基)卟啉荧光熄灭法测定铅

基于铅对荧光试剂 Meso- 5 ,10 ,15 ,2 0 -四 (4 -甲氧基苯基 )卟啉 (TMOPP)的荧光熄灭 ,建立了测定微量铅的荧光分析方法。在 p H9.5的 Tris- HCl缓冲体系中 ,最大激发波长和发射波长分别为 4 2 4 nm和6 5 7nm,测定铅浓度的线性范围为 5 .5 0× 10 -7— 7.5 0× 10 -5mol/ L,检出限为 8.5 0× 10 -8mol/ L。用于环境水样中铅含量的分析 ,结果满意。     

用EDTP进行微量Ce3+离子的荧光光度测定

Ce3+离子在pH 7～8的溶液中,与乙二胺四亚甲基膦酸(EDTP)形成1∶1的配合物时,Ce3+离子的自身荧光得到的明显的增强.本文研究了这种荧光增强作用用于溶液中微量Ce3+荧光分析的方法.结果表明,用该配合物体系进行Ce3+的荧光分析时,配合物的最大激发和发射波长分别在313 nm和397 nm,工作曲线在1×10-8 mol.L-1～1×10-4 mol·L-1的范围内呈很好的直线,在灵敏度和线性范围方面接近已知的最好的荧光分析方法,而由于Ce3+与EDTP形成非常稳定的配合物,同时使Ce3+离子的发光有较大的红移,因此在消除干扰离子的影响特别是Pr3+和PO3-4的干扰方面明显优于其他方法.     

微量元素对B族维生素同步荧光分析法影响的研究

本文探讨了钙、镁、铜等 7种微量元素对维生素 B1、B2 、B6的同步荧光光谱的影响。实验结果表明 ,当Ca2 + 的浓度为 1.0× 10 -3mol/ L时 ,VB2 、VB6的同步荧光光谱有显著的增强作用 ;而其他微量元素对VB1、VB2 、VB6的同步荧光有不同程度的猝灭或增强作用。利用 Ca2 + 对 3种维生素荧光强度的增敏作用 ,可以有效地提高同步荧光分析法同时测定 VB1、VB2 、VB6的灵敏度 ,VB1、VB2 、VB6的校准曲线的线性范围分别为 2 .4× 10 -7— 9.0× 10 -6、1.1× 10 -7— 4 .6× 10 -6、7.1× 10 -7— 2 .0× 10 -6mol/ L。采用本方法测定混合样品 ,样品不需分离 ,操作简便、快速     

配合物Eu(C5H8NO3)2(C3H5N2)2Cl3·3H2O光致发光性能

利用OPO激光激发光谱和三维荧光光谱研究了配合物Eu(C5H8NO3)2(C3H5N2)2Cl3·3H2O固体粉末在不同激发光源下的荧光特性,测试了不同浓度配合物水溶液的荧光光谱.固体荧光结果显示该配合物具有很好的荧光性能,当激发光波长为320-400nm时,产生波长分别为400-500nm、580-620nm及690-710nm的三个荧光区;当激发光波长为700-880nm时产生峰值为450nm升频转换荧光,激发光波长为700-800nm时产生峰值分别为590nm和615nm的升频转换荧光.溶液荧光结果表明在10-4-10-2mol/L浓度范围内荧光强度与溶液浓度呈正相关.对其可能的发光机制进行了探讨.     

荧光光度法测定胰腺肿瘤细胞膜上的潘生丁

测定了胰腺肿瘤细胞膜上的潘生丁在乙腈 -水溶液中的荧光光谱和强度 ,并推算出胰腺肿瘤细胞膜上核苷载体的数量。潘生丁的浓度与其荧光强度在 1.0× 10 -12 — 5 .0× 10 -5mol/ L范围内呈线性关系 ,检出限为 2 .8× 10 -13 mol/ L(1.4× 10 -4ng/ m L) ,相对标准偏差为 2 .7%。     

邻苯二甲醛的荧光光度法测定

在 p H11.0的缓冲介质中 ,邻苯二甲醛与 l-组氨酸形成的复合物在 5 4 0 nm处发射出强烈荧光 ,由此建立了邻苯二甲醛的荧光光度分析新方法 ,并系统的研究了邻苯二甲醛与 l-组氨酸结合的反应条件。本法检出限为 1.2× 10 -8mol/ L,荧光强度与浓度在 4 .0× 10 -8— 4 .0× 10 -6 mol/ L范围内呈良好的线性关系。将该法用于消毒剂中邻苯二甲醛的测定 ,回收率为 95 .8%— 10 6.5 %。     

DBC-偶氮胂分光光度法测定水样中钙

在 p H10 .9H3 BO3 - H3 PO4- HAc缓冲介质中 ,Ca2 +与 DBC-偶氮胂生成 1∶ 2蓝色络合物 ,最大吸收波长位于 6 2 0 nm处 ,表观摩尔吸光系数ε62 4nm=1.86× 10 4L· mol-1· cm-1,钙量在 0— 1.4μg/ m L范围内遵守比耳定律。本法用于水样中钙的测定 ,结果令人满意。     

2-(1,3,4-三氮唑偶氮)-5-二乙氨基苯甲酸光度法测定铜的研究

本文研究了新显色剂 2 - ( 1,3,4 -三氮唑偶氮 ) - 5 -二乙氨基苯甲酸 ( TZDBA)与铜显色反应的条件。在0 .1mol/L的 HCl介质中 ,TZDBA与 Cu2 +形成稳定的紫红色络合物。其最大吸收波长在 5 78nm处 ,表观摩尔吸光系数为 4 .0× 10 4 L· mol-1·cm-1,Cu2 +质量浓度在 0— 10 μg/2 5 m L范围内符合比耳定律。所拟方法可不经分离直接测定镁合金和铝合金标样中的微量铜 ,加标回收率为 10 1.0 %— 10 1.4 % ,RSD( n=6)为 2 .0 %— 3.9% ,结果令人满意     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Research on beamforming method for dual-line array with space mismatch between the two line arrays

The performance of port/starboard discrimination of dual-line array will be seriously degraded when the space between the two line arrays of the dual-line array is mismatched. The directivity function of the delay-sum and delay-subtract beamforming is deduced and the port/starboard discrimination of the delay-sum and delay-subtract beamforming is also studied both under the ideal status and the status under which the space between the two line arrays of the dual-line array is mismatched. Analysis results show the delay-subtract beamforming has better performance of port/starboard discrimination. At last, the sea trial results demonstrate the theoretical results.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Retrieval of ultraviolet skylight radiances and O3 slant column densities from balloon-borne limb spectrometer

With a novel light-weight and absolutely calibrated ultraviolet （UV） spectrometer, UV skylight radiances and O3 slant column densities are measured by balloon-borne limb measurements in Xinjiang area, China. UV skylight radiances measured at the height of 31 km are compared with the results from Modtran in the wavelength range from 290 to 420 nm. O3 slant column densities are derived from radiance spectra in the Huggins bands （320 - 335 nm） using differential optical absorption spectroscopy method. And the parameter exhibits a good correlation with the same value simulated by radiative transfer model （Tracy）. The O3 profile simultaneously measured by an O3 sonde is used as input in Tracy calculations. The O3 sonde is launched on the same balloon.     

Design optimization of highly sensitive LSPR enhanced surface plasmon resonance biosensors with nanoholes

For breaking through the sensitivity limitation of conventional surface plasmon resonance (SPR) biosensors, novel highly sensitive SPR biosensors with Au nanoparticles and nanogratings enhancement have been proposed recently.But in practice, these structures have obvious disadvantages.In this study, a nanohole based sensitivity enhancement SPR biosensor is proposed and the influence of different structural parameters on the performance is investigated by using rigorous coupled wave analysis (RCWA).Electromagnetic field distributions around the nanohole are also given out to directly explain the performance difference for various structural parameters.The results indicate that significant sensitivity increase is associated with localized surface plasmons (LSPs) excitation mediated by nanoholes.Except to outcome the weakness of other LSP based biosensors, larger resonance angle shift, reflectance amplitude, and sharper SPR curves' width are obtained simultaneously under optimized structural parameters.     

Polymer gratings based on photopolymerization for low-order distributed feedback polymer lasers

Novel polymer distributed feedback(DFB)gratings are fabricated based on photopolymerization to reduce lasing threshold of polymer lasers.A photopolymer formulation sensitive to 355-nm ultraviolet(UV)light is proposed for the fabrication of polymer gratings and it can be used to form polymer films by spin-coating process.A very low surface-relief depth ranging from 12.5 to about 1.0 nm has been demonstrated with a refractive-index modulation of about 0.012.The experimental results indicate that such polymer gratings have promising potentials for the fabrication of low-order DFB organic semiconductor lasers.     

A novel methodology for photometric compensation of projection display on patterned screen

We propose a novel methodology based on the projector-camera (ProCam) system to address the photometric compensation issue for the projection display on the patterned screen.The patterned screen is treated as the combination of a perfect white screen and a color modulator.The perfect white screen is used to automatically and accurately characterize the ProCam system offline using the polynomial model,and the parameters of the color modulator can be efficiently recovered by employing only two gray images based on the linear reflectance model.The experimental results show that the color artifacts of the display image can be greatly improved with this methodology,which demonstrates its feasibility and validity in the photometric compensation.