Dielectric properties of the composite system polyurethane — sodium chloride

Summary The dielectric properties of the composite system polyurethane-sodium chloride have been measured at frequencies between 10^–4 Hz and 3 · 10⁵ Hz in the temperature range from –150 °C up to +90 dgC. Three dielectric loss mechanisms have been found; they are indicated by ₁, ₂ and. The activation energy of the ₁-transition is 35 kcal/mole, that of the-transition 6.7 kcal/mole. The ₂-loss peak was only observed at frequencies of 10³ Hz and higher, forming one broad peak with the ₁-loss peak at lower frequencies. In the composite materials, the- and ₂-loss peaks measured at fixed frequencies were found at the same temperature. The ₂-loss peak, however, was shifted to a lower temperature, due to the sodium chloride filler. Comparison of experimental data of and tan with theoretical predictions concerning the dielectric properties of composite systems showed only partial agreement. The difference mainly consisted in. the temperature shift in the tan-peak of the ₁-transition.

---

Zusammenfassung Die dielektrischen Eigenschaften des Verbundssystems Kochsalz-Polyurethankautschuk wurden im Frequenzgebiet zwischen 10^–4 Hz und 3.10⁵ Hz und im Temperaturbereich von –150 °C bis +90 °C gemessen. Es wurden drei dielektrische Verlustmaxima gefunden, die mit ₁, ₂ und angedeutet werden. Die Aktivierungsenergie des ₁-Überganges beträgt 35 kcal/Mol, die des-Überganges 6.7 kcal/Mol. Das ₂-Maximum konnte nur bei Frequenzen höher als 10³Hz vom ₁-Maximum gesondert erfaßt werden. Die Lage der ₂- und-Maxima war vom Füllgrad unabhängig. Das ₁-Maximum verschiebt sich mit steigendem Füllgrad zu niedrigeren Temperaturen. Die gemessenen Werte von und tan stimmen nur teilweise mit den Aussagen einer Theorie der dielektrischen Eigenschaften von Mischkörpern überein.

     

Gasdynamics of a plasma in a multiple-mirror magnetic trap with “point” mirrors

Equations are derived for the gasdynamics of a dense plasma confined by a multiple-mirror magnetic field. The limiting cases of large and small mean free paths have been analyzed earlier: ₀ and k, where is the length of an individual mirror machine, ₀ is the size of the mirror, and k is the mirror ratio. The present work is devoted to a study of the intermediate range of mean free paths ₀ k. It is shown that in this region of the parameters the process of expansion of the plasma has a diffusional nature, and the coefficients of transfer of the plasma along the magnetic field are calculated.Translated from Zhurnal Prikladnoi Mekhaniki i Tekhnicheskoi Fiziki, No. 6, pp. 14–19, November–December, 1974.The authors thank D. D. Ryutov for the statement of the problem and interest in the work.     

On the measurement of normal stress differences in steady shear flow

Summary Compared to the similar pressure-distribution cone-and-plate apparatus of Adams and Lodge (4), the new apparatus' improvements include: temperature control of the cone (as well as the plate); increased stiffening of the frame; four (not three) pressuremeasuring holes in the cone/plate region; inclusion of a pressure-measuring hole on the axis under the cone truncation; exclusive use of a vertical free liquid boundary at the cone rim (without a sea of liquid). Temperature control of the rotating cone and of the fixed plate leads to acceptable temperature uniformity in the test liquid for working temperatures within 10°C or 20°C of ambient; the corresponding interval is about 1°C if the cone temperature control is abandoned. Pressure gradients measured using a Newtonian liquid agree with those calculated using Walters' eq. (3). For a viscoelastic liquid, after subtracting inertial contributions, pressure distributions measured at a given shear rate in the cone/plate region do not change when the gap angle is changed from 2° to 3°, showing that the effects of secondary flow are negligible. Values ofN ₃ =N ₁ + 2N ₂ obtained from the gradients of these distributions are believed to be in error by not more than ±1 Pa, in favorable cases. The present most useful ranges are: 10 to 5000 Pa forN ₃; 0.1 to 200 sec^–1 for shear rate; up to 5 Pa s for viscosity; and 5 to 40°C for temperature. As an application, it is shown that adding 0.1% of a high molecular weight polyisobutylene to a 2% polyisobutylene solution doublesN ₃ and has no detectable effect on the viscosity measured at low shear rates with a Ferranti-Shirley viscometer.

---

Zusammenfassung Im Vergleich zu dem ähnlichen Kegel-Platte-Gerät von Adams und Lodge (4) zur Messung der Druckverteilung wurden an dem neuen Gerät die folgenden Verbesserungen vorgenommen: Temperaturregelung an Kegel und Platte, Versteifung des Rahmens, vier (anstatt drei) Druckmeßlöcher im Kegel-Platte-Bereich, ein zusätzliches Druckmeßloch auf der Achse unter der Kegelstumpf-Deckfläche, ausschließliche Verwendung einer vertikalen freien Grenzfläche der Flüssigkeit am Kegelrand (ohne umgebenden Flüssigkeitssee). Die Temperaturregelung des rotierenden Kegels und der festen Platte führt zu einer ausreichenden Temperaturgleichförmigkeit in der Testflüssigkeit für Betriebstemperaturen, die höchstens um 10–20°C von der Umgebungstemperatur abweichen. Dieses Intervall beträgt dagegen nur etwa 1°C, wenn auf die Temperaturregelung am Kegel verzichtet wird. Für newtonsche Flüssigkeiten entsprechen die gemessenen Druckgradienten den mittels der Gleichung von Walters (3) berechneten. Für viskoelastische Flüssigkeiten zeigen sich bei der Änderung des Spaltwinkels von 2° auf 3° nach Abzug der Trägheitsbeiträge keine Änderungen der bei einer bestimmten Schergeschwindigkeit gemessenen Druckverteilung. Dies zeigt, daß Sekundärströmungseffekte vernachlässigbar sind. Es darf angenommen werden, daß die Werte vonN ₃ =N ₁ + 2N ₂, die man aus den Gradienten dieser Verteilungen erhält, unter günstigen Umständen mit einem Fehler von nicht mehr als ±1 Pa behaftet sind. Gegenwärtig liegen die günstigsten Bereiche bei 10 bis 5000 Pa fürN ₃, 0,1 bis 200 s^–1 für die Schergeschwindigkeit, unterhalb von 5 Pa s für die Viskosität und 5 bis 40°C für die Temperatur. Als Anwendung wird gezeigt, daß ein Zusatz von 0,1% hochmolekularen Polyisobutylens zu einer 2%igen Polyisobutylenlösung den Wert vonN ₃ verdoppelt, aber keinen erkennbaren Einfluß auf die (bei geringen Schergeschwindigkeiten mit einem Ferranti-Shirley-Viskosimeter gemessen) Viskosität hat.

---

udsf unidirectional shear flow - TCP truncated-cone and plate - N ₁,N ₂ 1st and 2nd normal stress differences in udsf - N ₃ N ₁ + 2N ₂ - : = A is defined by the equationA := B - P ^* hole pressurePw – Pm; Pw, Pm = pressures measured by flush transducer and by hole-mounted transducer - t time - , strain rate, shear rate - (P,t) covariant body metric tensor at particleP and timet - ⁱ , _i covariant and contravariant udsf body base vectors (i = 1, 2, 3) - ^–1 inverse of - R, plate radius, cone/plate gap angle - r ₀,h ₀ radius and height of cone truncation - r,, spherical polar coordinates; cone axis = 0; plate surface = /2 - physical components of stress; for a tensile component - cone angular velocity - p on the plate = /2 - ,T, density, absolute temperature, viscosity - P 0.15 ²(r ² –R ²) (inertial contribution) [2.7] - P _ve contribution [2.8] from flow perturbations of viscoelastic origin - r _i i = 1,2,3,4; values ofr at centers of holes in cone/plate region - P _i () pressure change recorded by transducerTi when cone angular velocity goes from zero to - 1/2 {P _i ()+ P _i (–)} (average for 2 senses of rotation) - rim pressure, from least-squares line through four points - Re Reynolds' number:R ²/ - (P,t)/t With 11 figures and 2 tables     

Unsteady forced convection heat/mass transfer from a flat plate

Numerical methods are used to investigate the transient, forced convection heat/mass transfer from a finite flat plate to a steady stream of viscous, incompressible fluid. The temperature/concentration inside the plate is considered uniform. The heat/mass balance equations were solved in elliptic cylindrical coordinates by a finite difference implicit ADI method. These solutions span the parameter ranges 10 Re 400 and 0.1 Pr 10. The computations were focused on the influence of the product (aspect ratio) × (volume heat capacity ratio/Henry number) on the heat/mass transfer rate. The occurrence on the plates surface of heat/mass wake phenomena was also studied.     

Die Temperaturabhängigkeit der Oberflächenspannung von reinen Kältemitteln vom Tripelpunkt bis zum kritischen Punkt

Zusammenfassung Die Oberflächenspannung von sechs reinen Substanzen — SF₆, CCl₃F, CCl₂F₂, CClF₃, CBrF₃ und CHClF₂ — wurde mit Hilfe einer modifizierten Kapillarmethode gemessen. Die zur Berechnung der Oberflächenspannung erforderlichen Sättigungsdichten und wurden teils aus vorhandenen Zustandsgleichungen, teils aus ebenfalls gemessenen Brechungsindizes bestimmt. Die Temperaturabhängigkeit der Oberflächenspannung läßt sich durch einen erweiterten Ansatz nach van der Waals =_O (T_c-T)(1+...) darstellen, wobei bei einfachen Stoffen ein eingliedriger, bei polaren und assoziierenden Stoffen ein zweigliedriger Ansatz notwendig und ausreichend ist. Für den kritischen Exponenten der Oberflächenspannung wurde ein von der molekularen Substanz weitgehend unabhängiger Wert von =1.284±0.005 gefunden.

---

Temperature dependence of surface tension of pure refrigerants from triple point up to the critical point

The surface tension of six fluids (SF₆, CCl₃F, CCl₂F₂, CClF₃, CBrF₃, CHClF₂) have been measured by means of a modified capillary rise method. The liquid vapor densities, which are needed to calculate the surface tension, have partly been determined by means of refractive indices simultaneously measured in the same apparatus. The temperature dependence of the surface tension is described by an extended van der Waals power law =_O(T_c-T)(1+...). For simple fluids one term and for polar and associating fluids two terms are necessary and sufficient. The critical exponent is found to be 1.284 ± 0.005 and nearly independent of the molecular structure.

---

Formelzeichen a² Laplace-Koeffizient - a Parameter - B_O, B_on Koeffizient der Koexistenzkurve - g Erdbeschleunigung - H Höhe, kapillare Steighöhe - LL Lorentz-Lorenz-Funktion oder Refraktionskonstante - M molare Masse - M Zahl der Meßwerte - N Zahl der unbekannten Parameter - n Brechungsindex - p Druck - R,r Radius - s Entropie - SD Standardabweichung - T, t Temperatur - u innere Energie Griechische Formelzeichen Exponent des Laplace-Koeffizienten - Exponent der Koexistenzkurve - 2. Exponent der Oberflächenspannung - Wellenlänge des Lichts - Exponent der Oberflächenspannung - _D Dipolmoment - , Dichte der Flüssigkeit bzw. des Dampfes - Oberflächenspannung - reduzierte Temperatur (1-T/T_c) - ² gewichtete Varianz Indizes c kritischer Zustand - D Differenz - m Mittelwert - T Isotherme - t Zustand am Tripelpunkt - S Zustand am Schmelzpunkt - bezogen auf Oberfläche     

The effect of surface mass transfer on buoyancy induced flow in a variable porosity medium adjacent to a vertical heated plate

The effect of surface mass transfer on buoyancy induced flow in a variable porosity medium adjacent to a heated vertical plate is studied for high Rayleigh numbers. Similarity solutions are obtained within the frame work of boundary layer theory for a power law variation in surface temperature,T _Wx and surface injectionv _Wx(–1/2). The analysis incorporates the expression connecting porosity and permeability and also the expression connecting porosity and effective thermal diffusivity. The influence of thermal dispersion on the flow and heat transfer characteristics are also analysed in detail. The results of the present analysis document the fact that variable porosity enhances heat transfer rate and the magnitude of velocity near the wall. The governing equations are solved using an implicit finite difference scheme for both the Darcy flow model and Forchheimer flow model, the latter analysis being confined to an isothermal surface and an impermeable vertical plate. The influence of the intertial terms in the Forchheimer model is to decrease the heat transfer and flow rates and the influence of thermal dispersion is to increase the heat transfer rate.

---

Der Effekt des Oberflächenstoffaustausches bei auftriebsinduzierter Strömung in einem variablen porösen Medium, das an eine vertikale, beheizte Platte angrenzt

Zusammenfassung Es wird der Effekt des Oberflächenstoffaustausches in auftriebsinduzierter Strömung in einem variablen porösen Medium, das an eine vertikale, beheizte Platte angrenzt, für große Reynoldszahlen untersucht. Ähnliche Lösungen werden im Rahmen der Grenzschicht-Theorie, durch Variation des Potenzansatzes der Oberflächentemperatur,T _Wx , und der Oberflächengeschwindigkeit,v _Wx(–1/2), erreicht. Die Analyse vereinigt sowohl den Ausdruck, der Porösität und Permeabilität verbindet, als auch den Ausdruck, der Porösität und Wärmeleitfähigkeit miteinander verbindet. Der Einfluß der Temperaturverteilung auf Strömung und Wärmeübergangskennzahlen wird ebenfalls im Detail analysiert. Als Ergebnis der vorliegenden Untersuchung ergibt sich die Tatsache, daß variable Porösität Wärmeübertragungsrate und Betrag der Geschwindigkeit in Wandnähe steigert. Die bestimmenden Gleichungen, sowohl für das Darcysche Strömungsmodell als auch für das Forchheimersche Strömungsmodell, werden mit Hilfe eines implizierten Differenzenschemas gelöst. Die Berechnung wird für die beiden Fälle, isotherme Oberfläche und undurchlässige vertikale Platte, angewandt. Der Einfluß der Terme für die Trägheitskräfte im Forchheimerschen Modell senkt Wärmeübergangs- und Durchgangsrate, wogegen die Wärmeübergangsrate durch den Einfluß der Temperaturverteilung erhöht wird.

---

Nomenclature a constant defined by Eq. (12) - A constant defined by Eq. (12) - B constant defined by Eq. (3) - b _s/_f ratio of thermal conductivities - C constant defined by Eq. (1) - C _P specific heat of the convective fluid - d particle diameter - f dimensionless function defined by Eq. (14) - f _w lateral mass flux parameter - g acceleration due to gravity - k ₀ mean permeability of the mediumk ₀= ₀ ³ d ²/150 (1– ₀)² k ₀=1.75d/(1– ₀) 150 (Inertia parameter) - L length of the source or sink - m mass transfer - n constant defined in Eq. (12) - k (y) permeability of the porous medium - k (y) interial coefficient in the Ergun expression - Gr modified Grashof numberGr=(g k ₀ k ₀ (T _w–))/ ² - R _a Rayleigh number (g k ₀ x T _w–)/ - R _ad modified Rayleigh number (g k ₀ d|T _w–|)/ - N _u Nusselt number - s x/d - Q overall heat transfer rate - T temperature - T _w surface temperature - T ambient fluid temperature - u velocity in vertical direction - v velocity in horizontal direction - x vertical coordinate - y horizontal coordinate Greek symbols ₀ mean thermal diffusivity _f/ C_p - coefficient of thermal expansion - constant defined in Eq. (4) - ratio of particle to bed diameter - _e effective thermal conductivity - f thermal conductivity of fluid - _s thermal conductivity of solid - dimensionless similarity variable in Eq. (13) - value of at the edge of the boundary layer - constant defined in Eq. (1) - _e effective molecular thermal diffusivity - (y) porosity of the medium - ₀ mean porosity of the medium - viscosity of the fluid - ₀ density of the convective fluid - stream function - w condition at the wall - condition at infinity     

Minimum-drag cascade design for an “impeller-directing vanes-unchoked convergent nozzle” system

The variational problem of designing the slender airfoils of the plane cascade of an impeller-directing vanes-unchoked convergent nozzle system in a supersonic ideal (inviscid and non-heat-conducting) gas flow with a subsonic normal velocity component is solved in the linear approximation. The minimized functional is the axial component of the force acting on the system. The conditions to be met by the optimized airfoils include the specification of the projection of the force applied to the cascade onto the axis running parallel to its front, and the free stream condition. Flows past rather sparse cascades, whose discontinuous characteristics departing from the lower surface of an airfoil, do not impinge on the upper surface of the adjacent airfoil are considered.By analogy with an isolated cascade [1], the upper and lower generators of the optimum airfoils are constructed of straight-line segments. In the calculated example the quadrangular airfoils whose generator segments are inclined in accordance with the double-sided extremum conditions are shown to be optimum.Moscow. Translated from Izvestiya Rossiiskoi Akademii Nauk, Mekhanika Zhidkosti i Gaza, No. 3, pp. 162–165, May–June, 1996.     

Two-dimensional transonic vortex flows of an ideal gas

Equations are obtained for two-dimensional transonic adiabatic (nonisoenergetic and nonisoentropic) vortex flows of an ideal gas, using the natural coordinates (=const is the family of streamlines, and =const is the family of lines orthogonal to them). It is not required that the transonic gas flow be close to a uniform sonic flow (the derivation is given without estimates). Solutions are found for equations describing vortex flows inside a Laval nozzle and near the sonic boundary of a free stream.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 5, pp. 105–109, September–October, 1973.     

Calculation of the pressure on the side surface of bodies consisting of a spherical segment joined to an inverted cone in a supersonic stream

The results of investigations of inviscid flow over inverted cones with nose consisting of a spherical segment were published for the first time in Soviet literature in [1–4]. In the present paper, a numerical solution to this problem is obtained using the improved algorithms of [5, 6], which have proved themselves well in problems of exterior flow over surfaces with positive angles of inclination to the oncoming flow. It is shown that the Mach number 2 M , equilibrium and nonequilibrium physicochemical transformations in air (H = 60 km, V = 7.4 km/sec, R₀ = 1 m), and the angle of attack 0 40° influence the investigated pressure distributions. A comparison of the results of the calculations with drainage experiments for M = 6, = 0-25° confirms the extended region of applicability of the developed numerical methods. Also proposed is a simple correlation of the dependence on the Mach number in the range 1.5 M of the shape of the shock wave near a sphere in a stream of ideal gas with adiabatic exponent = 1.4.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 1, pp. 178–183, January–February, 1981.     

Viscoelastic swirling flow with free surface in cylindrical chambers

The flow of a viscoelastic liquid driven by the steadily rotating bottom cover of a cylindrical cup is investigated. The flow field and the shape of the free surface are determined at the lowest significant orders of the regular domain perturbation in terms of the angular velocity of the bottom cap. The meridional field superposed on a primary azimuthal field shows a structure of multiple cells. The velocity field and the shape of the free surface are strongly effected by the cylinder aspect ratio and the elasticity of the liquid. The use of this flow configuration as a free surface rheometer to determine the first two Rivlin-Ericksen constants is shown to be promising.Nomenclature R, ,Z Coordinates in the physical domain D - , , Coordinates in the rest stateD ₀ - r, ,z Dimensionless coordinates in the rest stateD ₀ - Angular velocity - Zero shear viscosity - Surface tension coefficient - Density - Dimensionless surface tension parameter - ₁, ₂ The first two Rivlin-Ericksen constants - Stream function - Dimensionless second order meridional stream function - ^* Dimensionless second normal stress function - 2 Dimensionless sum of the first and second normal stress functions - N ₁,N ₂ The first and second normal stress functions - n Unit normal vector - D Stretching tensor - A _n nth order Rivlin-Ericksen tensor - S Extra-stress - u Velocity field - U Dimensionless second order meridional velocity field - V Dimensionless first order azimuthal velocity field - p Pressure - Modified pressure field - P Dimensionless second order pressure field - J Mean curvature - a Cylinder radius - d Liquid depth at rest - D Dimensionless liquid depth at rest - h Free surface height - H Dimensionless free surface height at the second order     

Application of the Chapman-Enskog method to the case of a binary two-temperature gas mixture

An interesting property of the flows of a binary mixture of neutral gases for which the molecular mass ratio =m/M1 is that within the limits of the applicability of continuum mechanics the components of the mixture may have different temperatures. The process of establishing the Maxwellian equilibrium state in such a mixture divides into several stages, which are characterized by relaxation times _i which differ in order of magnitude. First the state of the light component reaches equilibrium, then the heavy component, after which equilibrium between the components is established [1]. In the simplest case the relaxation times differ from one another by a factor of ^*.Here the mixture component temperature difference relaxation time _T /, where is the relaxation time for the light component. If 1, 1, so that _T ~1, then for the characteristic hydrodynamic time scale t~1 the relative temperature difference will be of order unity. In the absence of strong external force fields the component velocity difference is negligibly small, since its relaxation time _vt1.In the case of a fully ionized plasma the Chapman-Enskog method is quite easily extended to the case of the two-temperature mixture [3], since the Landau collision integral is used, which decomposes directly with respect to . In the Boltzmann cross collision integral, the quantity appears in the formulas relating the velocities before and after collision, which hinders the decomposition of this integral with respect to , which is necessary for calculating the relaxation terms in the equations for temperatures differing from zero in the Euler approximation [4] (the transport coefficients are calculated considerably more simply, since for their determination it is sufficient to account for only the first (Lorentzian [5]) terms of the decomposition of the cross collision integrals with respect to ). This led to the use in [4] for obtaining the equations of the considered continuum mixture of a specially constructed model kinetic equation (of the Bhatnagar-Krook type) which has an undetermined degree of accuracy.In the following we use the Boltzmann equations to obtain the equations of motion of a two-temperature binary gas mixture in an approximation analogous to that of Navier-Stokes (for convenience we shall term this approximation the Navier-Stokes approximation) to determine the transport coefficients and the relaxation terms of the equations for the temperatures. The equations in the Burnett approximation, and so on, may be obtained similarly, although this derivation is not useful in practice.     

Some problems concerning nonstationary currents in dense plasma systems confined by walls

Nonstationary currents are examined in a dense magnetized plasma with 1, in which energy release and heat loss by thermal conduction and radiation are possible. Solutions are found in two limiting cases: ¦f¦ ¦ div (T)¦ and ¦f¦ ¦ div(T)¦ (f is the radiation intensity, is the coefficient of heat conduction, and T is the temperature). In the first case a solution was obtained of some problems of the cooling and heating of a plasma illustrated in part by the evolution in time of the temperature profile in the boundary layer. In the second case an isomorphic solution was found for an arbitrary dependence of the coefficient of heat conduction on the temperature, pressure, and magnetic field.Translated from Zhurnal Prikladnoi Mekhaniki i Tekhnicheskoi Fiziki, No. 1, pp. 3–8, January–February, 1972.The author is grateful to G. I. Budker for formulating the problem.     

Der Spannungs- und Verschiebungszustand drehsymmetrischer Membrane mit beliebig gekrümmter Meridiankurve

Zusammenfassung Die Einführung von Zylinderkoordinaten (x, r, ) in die Gleichgewichtsbedingungen der Schnittkräfte bzw. in die Beziehungen zwischen Verzerrung und Verschiebungen am differentialen Schalenabschnitt ermöglicht die Berechnung des Spannungs- und Verschiebungszustandes von drehsymmetrischen Membranen mit beliebig gekrümmter Meridiankurve auf die Integration einer einfachen, linearen partiellen Differentialgleichung zweiter Ordnung für eine charakteristische FunktionF bzw. zurückzuführen. Eine geschlossene Lösung und damit eine Darstellung der Schnittkräfte und Verschiebungen durch explizite Formeln ist bei harmonischer Belastung cosn für zwei Funktionsgruppen=x ² und=x ^–3 möglich. Im Sonderfall der drehsymmetrischen und der antimetrischen Belastung mitn=0 undn=1 gelten die Gleichungen der Schnitt- und Verschiebungsgrößen für eine beliebige Meridianfunktion=(). Die Betrachtungen der Randbedingungen offener Schalen bei harmonischer Belastung geben über die infinitesimalen Deformationen einer drehsymmetrischen Membran mit überall negativer Krümmung Aufschluß.     

The problems of nonlinear bending for orthotropic rectangular plate with four clamped edges

（黄家寅）（秦圣立）ＴＨＥＰＲＯＢＬＥＭＳＯＦＮＯＮＬＩＮＥＡＲＢＥＮＤＩＮＧＦＯＲＯＲＴＨＯＴＲＯＰＩＣＲＥＣＴＡＮＧＵＬＡＲＰＬＡＴＥＷＩＴＨＦＯＵＲＣＬＡＭＰＥＤＥＤＧＥＳ￥ＨｕａｎｇＪｉａｙｉｎ;ＱｉｎＳｈｅｎｇｌｉ（ＱｕｆｕＮｏｒｍａｌＵｎ...     

Lp-estimates for the nonlinear spatially homogeneous Boltzmann equation

This paper studies L^p-estimates for solutions of the nonlinear, spatially homogeneous Boltzmann equation. The molecular forces considered include inverse k^th-power forces with k > 5 and angular cut-off.The main conclusions are the following. Let f be the unique solution of the Boltzmann equation with f(v,t)(1 + ¦v²¦)^(s ₁ ^{+ /p)/2} L¹, when the initial value f ₀ satisfies f ₀(v) 0, f ₀(v) (1 + ¦v¦²)^(s ₁ ^{+ /p)/2} L¹, for some s₁ 2 + /p, and f ₀(v) (1 + ¦v¦²)^s/2 L^p. If s 2/p and 1 < p < , then f(v, t)(1 + ¦v¦²)^{(s s} ₁)^/2 L^p, t > 0. If s >2 and 3/(1+ ) < p < , thenf(v,t) (1 + ¦v¦²)^(s(s ₁ ^{+ 3/p))/2} L^p, t > 0. If s >2 + 2C₀/C₁ and 3/(l + ) < p < , then f(v,t)(1 + ¦v¦²)^s/2 L^p, t > 0. Here 1/p + 1/p = 1, x y = min (x, y), and C₀, C₁, 0 < 1, are positive constants related to the molecular forces under consideration; = (k – 5)/ (k – 1) for k^th-power forces.Some weaker conclusions follow when 1 < p 3/ (1 + ).In the proofs some previously known L-estimates are extended. The results for L^p, 1 < p < , are based on these L-estimates coupled with nonlinear interpolation.     

A non-dualistic unified field theory of gravitation,electromagnetism and spin

The wisdom of classicalunified field theories in the conceptual framework of Weyl, Eddington, Einstein and Schrödinger has often been doubted and in particular there does not appear to be any empirical reason why the Einstein-Maxwell (E-M) theory needs to be geometrized. The crux of the matter is, however not whether the E-M theory is aesthetically satisfactory but whether it answers all the modern questions within the classical context. In particular, the E-M theory does not provide a classical platform from which the Dirac equation can be derived in the way Schrödinger's equation is derived from classical mechanics via the energy equation and the Correspondence Principle. The present paper presents a non-dualistic unified field theory (UFT) in the said conceptual framework as propounded by M. A. Tonnelat. By allowing the metric formds ²=g dx ^v x ^v and the non-degenerate two-formF=(1/2> _l) dx ^vdx ^vto enter symmetrically into the theory we obtain a UFT which contains Einstein's General Relativity and the Born-Infeld electrodynamics as special cases. Above all, it is shown that the Dirac equation describing the electron in an external gravito-electromagnetic field can be derived from the non-dualistic Einstein equation by a simple factorization if the Correspondence Principle is assumed.     

Application of the method of integral diffusion to investigation of turbulent transfer

A number of authors have critically examined semiempirical mixing length theories [1]. A defect of these theories is connected with the fact that the magnitude of the mixing length, which is assumed to be small in constructing the theory, turns out in experiments to be comparable with the characteristic dimensions of the flow region. Thus, the concept of volume convection [2–4] or integral diffusion [5], which is understood to be a transfer mechanism in which the friction stress is not expressed in terms of the velocity gradient, is introduced along with the concept of gradient diffusion. In addition, there are a number of experimental papers [6] in which it is shown that the turbulent friction stress cannot be equal to zero at the place in the flow where the derivative of the velocity is equal to zero. Mixing length theory does not describe this effect.It is possible to generalize mixing length theory [7–9] in a way which eliminates these defects. Flow of an incompressible fluid is considered.     

On the boundary conditions at the macroscopic level

We study the problem of the boundary conditions specified at the boundary of a porous domain in order to solve the macroscopic transfer equations obtained by means of the volume-averaging method. The analysis is limited to the case of conductive transport but the method can be extended to other cases. A numerical study enables us to illustrate the theoretical results in the case of a model porous medium. Roman Letters _sf interfacial area of the s-f interface contained within the macroscopic system m² - A _sf interfacial area of the s-f interface contained within the averaging volume m² - C _p mass fraction weighted heat capacity, kcal/kg/K - d _s , d _f microscopic characteristic length m - g vector that maps to _s, m - h vector that maps to _f , m - K _eff effective thermal conductivity tensor, kcal/m s K - l REV characteristic length, m - L macroscopic characteristic length, m - n _fs outwardly directed unit normal vector for the f-phase at the f-s interface - n _e outwardly directed unit normal vector at the dividing surface - T ^* macroscopic temperature field obtained by solving the macroscopic equation (3), K - V averaging volume, m³ - V _s , V _f volume of the considered phase within the averaging volume, m³ - volume of the macroscopic system, m³ - _s , _f volume of the considered phase within the volume of the macroscopic system, m³ - dividing surface, m² Greek Letters _s , _f volume fraction - ratio of thermal conductivities - _s , _f thermal conductivities, kcal/m s K - spatial average density, kg/m³ - microscopic temperature, K - ^* microscopic temperature corresponding to T ^* , K - spatial deviation temperature K - error on the temperature due to the macroscopic boundary conditions, K - spatial average - ^s , ^f intrinsic phase average     

Rheology of molten polymers

Summary TheCross equation describes the flow of pseudoplastic liquids in terms of an upper and a lower Newtonian viscosity corresponding to infinite and zero shear, and ₀, and of a third material constant related to the mechanism of rupture of linkages between particles in the intermediate, non-Newtonian flow regime, Calculation of of bulk polymers is important, since it cannot be determined experimentally. The equation was applied to the melt flow data of two low density polyethylenes at three temperatures.Using data in the non-Newtonian region covering 3 decades of shear rate to extrapolate to the zero-shear viscosity resulted in errors amounting to about onethird of the measured ₀ values. The extrapolated upper Newtonian viscosity was found to be independent of temperature within the precision of the data, indicating that it has a small activation energy.The ₀ values were from 100 to 1,400 times larger than the values at the corresponding temperatures.The values of were large compared to the values found for colloidal dispersions and polymer solutions, but decreased with increasing temperature. This shows that shear is the main factor in reducing chain entanglements, but that the contribution of Brownian motion becomes greater at higher temperatures.

---

Zusammenfassung Die Gleichung vonCross beschreibt das Fließverhalten von pseudoplastischen Flüssigkeiten durch drei Konstante: Die obereNewtonsche Viskosität (bei sehr hohen Schergeschwindigkeiten), die untereNewtonsche Viskosität ₀ (bei Scherspannung Null), und eine Materialkonstante, die vom Brechen der Bindungen zwischen Partikeln im nicht-Newtonschen Fließbereich abhängt. Die Berechnung von ist wichtig für unverdünnte Polymere, wo man sie nicht messen kann.Die Gleichung wurde auf das Fließverhalten der Schmelzen von zwei handelsüblichen Hochdruckpolyäthylenen bei drei Temperaturen angewandt. Die Werte von ₀, durch Extrapolation von gemessenen scheinbaren Viskositäten im Schergeschwindigkeitsbereich von 10 bis 4000 sec^–1 errechnet, wichen bis 30% von den gemessenen ₀-Werten ab. Die Aktivierungsenergie der war so klein, daß die-Werte bei den drei Temperaturen innerhalb der Genauigkeit der Extrapolation anscheinend gleich waren. Die ₀-Werte waren 100 bis 1400 mal größer als die-Werte.Im Verhältnis zu kolloidalen Dispersionen und verdünnten Polymerlösungen war das der Schmelzen groß, nahm aber mit steigender Temperatur ab. Deshalb wird die Verhakung der Molekülketten hauptsächlich durch Scherbeanspruchung vermindert, aber der Beitrag derBrownschen Bewegung nimmt mit steigender Temperatur zu.