一种新型Ag_3PO_4/Ag/Ag_2Mo_2O_7纳米线光催化剂:三元纳米复合物的光催化活性（英文）

首次利用原位共沉淀技术成功制备Ag_3PO_4/Ag/Ag_2Mo_2O_7复合光催化剂.所制备Ag_3PO_4/Ag/Ag_2Mo_2O_7纳米复合物由Ag_3PO_4和Ag纳米粒子组装在Ag_2Mo_2O_7纳米线表面.可见光照射下(λ420nm),Ag_3PO_4/Ag/Ag_2Mo_2O_7复合物表现出优异的光催化性能,其光催化活性较Ag_3PO_4、Ag_2Mo_2O_7及Ag_3PO_4/Ag_2Mo_2O_7样品有较大提高.结果表明,Ag_3PO_4/Ag/Ag_2Mo_2O_7光催化性能提高的原因是Ag_3PO_4/Ag负载使催化剂比表面积的增加、可见光吸收范围增大,同时由于生成Ag_3PO_4/Ag/Ag_2Mo_2O_7三元异质结构有效抑制了光生电子空穴对的复合.     

纤维状TiO2/Bi2O3光催化剂的制备及其光催化性能

以C₁₆H₃₆O₄Ti和Bi(NO₃)·5H₂O为原料,以棉花纤维为生物模板,合成了系列纤维状TiO₂/Bi₂O₃光催化剂．采用XRD、SEM、UV-Vis等测试技术对样品的相结构、形貌和吸光性能等进行了表征分析．结果表明,样品中的Bi₂O₃为单斜相和四方相共存的混晶,纤维长度达到毫米级,     

磁载光催化剂ZnO/ SiO2/γ-Fe2O3的光催化性能

本文采用液相沉积法制备出了纳米SiO2/γ-Fe2O3复合粒子,在其表面负载ZnO, 从而得到了易于磁性固液分离的磁载光催化剂ZnO/SiO2/γ-Fe2O3, 并通过XRD和TEM等测试技术对样品进行了表征。以可溶性染料亚甲基兰等为降解对象, 研究了磁载光催化剂ZnO/SiO2/γ-Fe2O3在紫外光下的光催化活性。结果表明, 在γ-Fe2O3和ZnO之间包覆一层无定形SiO2可使催化剂降佳率由20.76%提高到95.63%,并且该磁载光催化剂对染料有较好的降解效果, 在三次循环使用后仍能保持较好的光催化性能.     

高稳定性Mn:ZnO/Mn2O3纳米复合光催化剂的制备及光催化特性

采用修饰的高分子网络凝胶法成功制备了Mn₂O₃复合Mn掺杂ZnO纳米复合光催化剂(Mn:ZnO/Mn₂O₃),并基于模拟太阳光照射下罗丹明B(RhB)及亚甲基蓝(MB)染料的光降解研究了催化剂光催化降解有机染料的特性。X射线衍射,扫描电子显微镜及BET比表面积测试结果显示,微量(0.1 mol%)Mn掺杂再复合微量(0.2 mol%)Mn₂O₃后,Mn:ZnO/Mn₂O₃的颗粒尺寸减小且分散性提高,有效比表面积增大。紫外-可见光吸收光谱表明,相对于纯ZnO,Mn:ZnO/Mn₂O₃在可见光区域的光吸收能力明显提高。光致发光光谱表明微量Mn掺杂和微量Mn₂O₃复合促进了光生电子-空穴对的分离。结合X射线光电子能谱,发现可见光吸收能力和光生电子-空穴对分离率的提高源于催化剂表面氧空位的增加以及Mn:ZnO和Mn₂     

Cu3Mo2O9/MoO3纳米复合材料制备及三甲胺气敏性能研究

水产品的新鲜度极大地影响着人类的生命及身体健康,水产品在存放过程中会释放出以三甲胺为代表的胺类气体,通过检测这类气体的浓度可以监控水产品的新鲜度.本文以具有优良气体敏感性能的MoO₃纳米带作为基体,通过引入Cu₃Mo₂O₉纳米颗粒制备Cu₃Mo₂O₉/MoO₃复合材料,具有非常好的三甲胺气体敏感性能、快速响应/恢复时间及长期稳定性.结果表明,采用这种复合材料制备的气敏元件在50—240℃,质量分数为5×10^-6时对三甲胺气体的响应可达到R_air/R_gas=13.9,最小检测极限的体积分数为2×10^-7.分布在MoO₃纳米带表面的Cu₃Mo₂O₉颗粒与基体形成异质结界面,利用Cu₃Mo₂O_...     

内嵌碳正八面体形貌Co3O4光催化活性研究

基于脱脂棉为牺牲模板,采用碳辅助法制备了内嵌碳的八面体形貌Co3O4,对其在模拟阳光下的光解水制氢气的能力进行了研究。X射线衍射（XRD）和扫描电镜（SEM）表征分析表明,制备的产物是具有规则正八面体形貌、粒径约为10 m的具有良好晶型的Co3O4。能谱（EDS）和光射线光电子能谱（XPS）结果表明,制备的产物内嵌无定形碳,碳源来自于脱脂棉制备过程中的不完全燃烧。实验结果表明制备的内嵌碳八面体形貌Co3O4具有良好的光解水制氢能力。     

内嵌碳正八面体形貌Co3O4光催化活性研究

基于脱脂棉为牺牲模板,采用碳辅助法制备了内嵌碳的八面体形貌Co3O4,对其在模拟阳光下的光解水制氢气的能力进行了研究。X射线衍射（XRD）和扫描电镜（SEM）表征分析表明,制备的产物是具有规则正八面体形貌、粒径约为10 m的具有良好晶型的Co3O4。能谱（EDS）和光射线光电子能谱（XPS）结果表明,制备的产物内嵌无定形碳,碳源来自于脱脂棉制备过程中的不完全燃烧。实验结果表明制备的内嵌碳八面体形貌Co3O4具有良好的光解水制氢能力。     

Gd2O3：Er/Yb纳米线、纳米片的制备与发光性质

采用水热法制备了Gd₂O₃:Yb³⁺/Er³⁺纳米线和纳米片,并研究了制备过程中溶液的pH值对产物形貌的影响以及样品形貌对发光性质的影响。将稀土氧化物溶于硝酸并与NaOH反应,使溶液pH值至预期值,将生成物离心、烘干和灼烧,得到最终产物。研究发现,制备样品过程中,中性溶液中易于形成纳米片,而碱性溶液中则会形成纳米线,而且碱性越强越容易形成纳米线。在980nm激光激发下,与纳米片相比,纳米线中Er³⁺的⁴I_13/2→⁴I_15/2的红外发射强度显著减弱,而²H_11/2/⁴S_3/2→⁴I_15/2和⁴F_9/2→⁴I_15/2的上转换发射相对增强,而且²H_11/2/⁴S_3/2→⁴I_15/2与⁴F_9/2→⁴I_15/2的荧光分支比略有增大。纳米线与纳米片相比,比表面积减小,由表面效应引起的无辐射弛豫过程的减弱导致了上述光谱的变化。     

NiFe2O4纳米线阵列的制备与磁性

在氧化铝模板的纳米孔洞中, 用电化学的方法沉积铁镍合金纳米线，经过550℃30h氧化处理 , 成功制备出 NiFe2O4纳米线阵列. 分别用扫描电子显微镜 (SEM) 、透射电 子显微镜 (TEM) 、x射线衍射仪 (XRD) 和振动样品磁场计 (VSM) 对样品的形貌、晶体结构 和磁学性质进行了表征测试. SEM和TEM观察结果显示氧化铝模板的孔洞分布均匀，孔心距约 为110nm; 纳米线的直径约为70nm. XRD显示纳米线阵列的物相结构为NiFe2O4; VSM测试结果表明，NiFe2O4纳米线阵列膜的易磁化方向垂直于膜面. 当垂直 磁化时磁滞回线的矩形比约为05，矫顽力为41×103A/m，比氧化处理前的铁镍合金 纳米线阵列都有显著提高. 关键词： 纳米线 Ni Fe2O4 矫顽力     

Li2CO3/K3PO4复合助熔剂对新型Y2O2S：0.09Ti长余辉磷光体发光性能的影响

采用高温还原法合成了一种新型无稀土掺杂Y₂O₂S:0.09Ti长余辉发光材料。基于助熔剂种类对长余辉发光材料特性的重要作用,选择了对余辉衰减初期和后期余辉强度有明显作用的Li₂CO₃和K₃PO₄两种助熔剂,研究了不同配比(以下用x表示,x=Li₂CO₃/(Li₂CO₃+K₃PO₄))的复合助熔剂对Y₂O₂S:0.09Ti磷光体晶体结构和发光性能的作用,以获得具有较好综合发光性能的Y₂O₂S:0.09Ti磷光体。采用PL光谱和余辉测试仪对材料的发光特性进行了表征,用XRD研究了其晶体结构的变化。XRD结果表明,在复合助熔剂范围内(x=0~1.0)均可获得单相性的Y₂O₂S:0.09Ti磷光体。同时发现复合助熔剂比例不同制备的样品中,Y₂O₂S:0.09Ti磷光体晶体择优取向也发生明显的变化,且高比例Li₂CO₃有助于Y₂O₂S:0.09Ti磷光体的晶体形成。复合助熔剂比例x对样品的激发峰与发射谱主峰位置(565nm)基本没有影响;但助熔剂比例x对发射峰强度则有明显影响,随着x增加,该磷光体的发光强度先增后减,在x=0.8时发光强度最大。     

三元异质结构Ag-Bi2MoO6/BiPO4光催化剂高效降解苯酚红

多组分复合体系有利于电荷的有效分离,减少电子空穴对的复合几率。通过低温液相法首次合成Ag-Bi₂MoO₆/BiPO₄三元异质结构光催化剂。利用XRD、SEM、EDX及XPS等技术对样品进行了表征。结果表明,Ag纳米粒子光照积累在Bi₂MoO₆/BiPO₄的表面,通过表面等离子共振增加对可见光的吸收,同时作为电子受体促进了光生电子的转移。Ag、BiPO₄和Bi₂MoO₆形成三元异质结构有效地抑制了光生电子空穴对的复合。Ag-Bi₂MoO₆/BiPO₄表现出优异的光催化性能,其光催化活性较BiPO₄、Bi₂MoO₆和Bi₂MoO₆/BiPO₄样品有较大提高。并且对Ag-Bi₂MoO₆/BiPO₄三元异质结构的光催化机制进行了讨论。光催化过程中反应活性物种捕获实验结果表明h⁺和O₂^·-是主要的活性基团.     

Synthesis and characterization of Ag/BiVO4 composite photocatalyst

Ag/BiVO₄ composite photocatalysts were hydrothermal synthesized and characterized by XRD, SEM, XPS and DRS techniques. Their photocatalytic activities were determined by oxidative decomposition of methyl orange in aqueous solution under visible light irradiation. It revealed that the doped Ag species greatly improved the visible light absorption abilities and morphologies of the composites, and thus lead to enhanced photocatalytic activities compared with that of the pure BiVO₄.     

Preparation of photocatalytic Fe2O3-TiO2 coatings in one step by metal organic chemical vapor deposition

There are two major difficulties in the TiO₂ liquid-solid photocatalytic system: effective immobilization of the TiO₂ particles; and improving the catalytic activity under visible light. To simultaneously solve these two problems, Fe₂O₃-TiO₂ coatings supported on activated carbon fiber (ACF), have been prepared in one step by a convenient and efficient method—metal organic chemical vapor deposition (MOCVD). XRD results revealed that Fe₂O₃-TiO₂ coatings mainly composed of anatase TiO₂, α-Fe₂O₃ phases and little Fe₂Ti₃O₉. The pore structure of ACF was preserved well after loading with Fe₂O₃-TiO₂ coatings. UV-vis diffuse reflectance spectra showed a slight shift to longer wavelengths and an enhancement of the absorption in the visible region for Fe₂O₃-TiO₂ coatings, compared to the pure TiO₂ sample. A moderate Fe₂O₃-TiO₂ loading (13.7 wt%) was beneficial to mineralizing wastewater because the intermediates could be adsorbed onto the surface of photocatalyst following decomposition. The stable performance revealed that the Fe₂O₃-TiO₂ coatings were strongly adhered to the ACF surface, and the as prepared catalysts could be reused showing potential application for wastewater treatment.     

Influence of postdeposition annealing on structural properties and electrical characteristics of thin Tm2O3 and Tm2Ti2O7 dielectrics

We describe the structural properties and electrical characteristics of thin thulium oxide (Tm₂O₃) and thulium titanium oxide (Tm₂Ti₂O₇) as gate dielectrics deposited on silicon substrates through reactive sputtering. The structural and morphological features of these films were explored by X-ray diffraction, X-ray photoelectron spectroscopy, secondary ion mass spectrometry, and atomic force microscopy, measurements. It is found that the Tm₂Ti₂O₇ film annealed at 800 °C exhibited a thinner capacitance equivalent thickness of 19.8 Å, a lower interface trap density of 8.37 × 10¹¹ eV⁻¹ cm⁻², and a smaller hysteresis voltage of ∼4 mV than the other conditions. We attribute this behavior to the Ti incorporated into the Tm₂O₃ film improving the interfacial layer and the surface roughness. This film also shows negligible degrees of charge trapping at high electric field stress.     

Anisotropic domain-wall dynamics in proton-irradiated KH2PO4

KH₂PO₄ single crystals have been studied by employing complex impedance measurements in view of the domain freezing effect. As a result, distinct behaviors of the anisotropic domain-wall dynamics in the activation energy of domain freezing and the Vogel–Fulcher temperature before and after proton irradiation have been identified in the anisotropic crystal structure.     

Chemical quenching of positronium in Fe2O3/Al2O3 catalysts

Fe₂O₃/Al₂O₃ catalysts were prepared by solid state reaction method using α-Fe₂O₃ and γ-Al₂O₃ nano powders. The microstructure and surface properties of the catalyst were studied using positron lifetime and coincidence Doppler broadening annihilation radiation measurements. The positron lifetime spectrum shows four components. The two long lifetimes τ₃ and τ₄ are attributed to positronium annihilation in two types of pores distributed inside Al₂O₃ grain and between the grains, respectively. With increasing Fe₂O₃ content from 3 wt% to 40 wt%, the lifetime τ₃ keeps nearly unchanged, while the longest lifetime τ₄ shows decrease from 96 ns to 64 ns. Its intensity decreases drastically from 24% to less than 8%. The Doppler broadening S parameter shows also a continuous decrease. Further analysis of the Doppler broadening spectra reveals a decrease in the p-Ps intensity with increasing Fe₂O₃ content, which rules out the possibility of spin-conversion of positronium. Therefore the decrease of τ₄ is most probably due to the chemical quenching reaction of positronium with Fe ions on the surface of the large pores.     

Solid state reaction synthesis and luminescence properties of Dy-doped Gd2Mo3O9 phosphor

Gd₂Mo₃O₉ phosphors with various Dy³⁺ concentrations were synthesized by a traditional solid-state reaction using Na₂CO₃ as a flux. The influence of reaction temperature and Dy³⁺-doping concentration on the crystal structure of the phosphors was examined by XRD (X-ray diffraction). The effect of Dy³⁺-doping concentration on the emissions of Mo-O bond and Dy³⁺ was experimentally investigated. The energy transfers between host and Dy³⁺ ions, and between Dy³⁺ ions were analyzed based on both the Van Uitert and I-H models. The chromatic properties of the phosphors were also discussed.     

Photoelectrocatalytic degradation of organic contaminants at Bi2O3/TiO2 nanotube array electrode

In the current work, TiO₂ nanotube array was prepared via electrochemical anode method. Then the Bi₂O₃ nanoparticles were deposited onto the TiO₂ nanotube array via dip-coating method from an amorphous complex precursor. The crystal structures were characterized via X-ray diffraction analysis. Their surface textures were observed via electron-scanning microscope. The prepared composite array electrode exhibited high photoelectrocatalytic activities towards degrading organic contaminants under visible light irradiation. High photoelectrocatalytic activities were also exhibited under UV light irradiation. The catalytic mechanism was discussed based on the analysis of electrochemical and degradation kinetics results. It is suggested a P (Bi₂O₃)-N (TiO₂) junction was formed to increase the catalytic activates. The stability of the electrode materials was confirmed finally.     

大规模合成具有氧空位的多孔Bi2O3用于有效降解亚甲基蓝

光催化降解有机污染物由于其具有低能耗和绿色环保的特点,已经成为研究的热点. 氧化铋纳米晶体的带隙在2.0∽2.8 eV之间,利用它催化可见光降解有机污染物具有较高的活性,从而引起了越来越多的关注. 尽管近年来已经开发了几种制备Bi₂O₃基半导体材料的方法,但是仍然难以用简单的方法大规模地制备高活性的Bi₂O₃催化剂. 因此,开发简单可行的大规模制备Bi₂O₃纳米晶体的方法对于工业废水处理的潜在应用具有重要意义. 本文通过蚀刻商用BiSn粉末,然后进行热处理,成功地大规模制备了多孔Bi₂O₃. 获得的多孔Bi₂O₃在亚甲基蓝(MB)的光催化降解中表现出优异的活性和稳定性. 对该机理的进一步研究表明,多孔Bi₂O₃合适的能带结构允许生成活性氧物种,例如O₂^-·和·OH,可有效降解MB.