Synthesis and properties of poly(hydroxamic acid) from crosslinked poly(methacrylate)

Poly(hydroxamic acid) chelating ion-exchange resin was prepared from crosslinked poly(methacrylate) beads. The starting polymer was prepared by a suspension polymerization of methacrylate and divinyl benzene. Conversion of the ester groups into the hydroxamic acid was carried out by treatment with hydroxylamine in an alkaline solution. Hydroxamic acid capacity of the product was 2.71 mmol/g. The resin exhibited high affinity towards Fe(III) and Pb ions and its capacities for Fe(III), Pb, Cu, Ni and Co ions were pH dependent. The ability of the resin to carry out the separation of Fe(III)CuCo/Ni and PbNi ions is also reported.     

Isotherms of poly(ethylene glycol) adsorption from aqueous solutions by carbon adsorbents

Isotherms of adsorption of poly(ethylene glycols) PEG300, PEG6000, and PEG15 000 from aqueous solutions on graphitized carbon black and active carbon were measured at 25°C. Isotherms of excess adsorption of PEG6000 and PEG15 000 from aqueous solutions on both adsorbents were characterized by a distinct maximum. Comparison of adsorption isotherms for PEG6000 and PEG15 000 on a mesoporous AU-87 carbon testified to the existence of a sieve effect upon the adsorption of large PEG15 000 macromolecules in the accessible pores of this adsorbent. The analysis of the dependence of maximal adsorption values on the PEG molecular mass indicated a possible unfolding of macromolecular coils in the field of adsorption forces. As a result, all oxygen and carbon atoms of PEG macromolecules in a monolayer tend to approach active sites on the surface of a carbon adsorbent. The calculated values of thickness of dense adsorption monolayers of PEG300, PEG6000, and PEG15 000 lie within 0.36–0.63 nm for both adsorbents. PEG300 adsorption monolayers also contain, in addition to macromolecules, molecules of a solvent (water).Translated from Kolloidnyi Zhurnal, Vol. 66, No. 6, 2004, pp. 856–859.Original Russian Text Copyright © 2004 by Eltekov, Eltekova, Roldughin.     

Small-angle neutron scattering study of poly(methyl methacrylate-block-sodium acrylate-block-methyl methacrylate) and poly(sodium acrylate-block-methyl methacrylate-block-sodium acrylate) triblock copolymers in aqueous solutions

 Small-angle neutron scattering experiments were made on poly(methyl methacrylate-block-sodium acrylate-block-methyl methacrylate) [p(MMA-b-NaA-b-MMA)] and p(NaA-b-MMA-b-NaA) solutions by varying the composition and the concentration of the polymer with and without 1 M NaCl added. Scattering curves could be evaluated by assuming that the polymers aggregate into polydisperse micelles. The experiments support the expectation that in the case of the p(MMA-b-NaA-b-MMA) block sequence the hydrophilic blocks form closed loops connected by both ends to the micellar cores; in the case of the p(NaA-b-MMA-b-NaA) block sequence they float freely in the solvent. The micellar cores exert considerable stability against dilution and added electrolyte. The interaction of charged micelles could be formally described in terms of volume exclusion and the Derjaguin–Landau–Verwey–Overbeek potential. Received: 20 December 2000 Accepted: 18 August 2001     

Viscoelastic properties of crosslinked solutions of poly(2-hydroxymethyl methacrylate) in diethylene glycol. VI. Comparison with poly(butyl methacrylate) and poly(butyl acrylate) networks crosslinked to very low degrees

On the basis of our own experimental and some literature data, the contributions of slow relaxation mechanisms to the shear modulus, (G_eN — G_e), and the parameter C₂ of the Mooney-Rivlin equation have been examined for lightly crosslinked poly(butyl methacrylate), poly(butyl acrylate), poly(2-hydroxyethyl methacrylate), and some rubber networks. For the rubbers, increasing degree of crosslinking caused a decrease in G_eN — G_e and an increase in C₂; for the other networks, both G_eN — G_e and C₂ diminished with increasing crosslinking. The effectiveness of the crosslinking polymerization, and also the absolute values of the physical crosslinking degree, decreased in the order of poly(2-hydroxyethyl methacrylate), poly(butyl methacrylate), and poly(butyl acrylate). The values of the equilibrium compliances J of the networks studied, obtained by various methods, have also been compared, and good agreement has been found.     

Titration microcalorimetry of poly(vinylpyrrolidone) and sodium dodecylbenzenesulphonate in aqueous solutions

Microcalorimetric titrations are carried out on solutions containing the anionic surfactant sodium dodecylbenzenesulphonate (SDBS), and mixtures of SDBS and the uncharged polymer poly(vinylpyrrolidone) (PVP). Measurements are taken at different temperatures. Micellisation of SDBS is driven by hydrophobic bonding. The interaction enthalpy of mixed PVP/SDBS systems shows clearly a consecutive endothermic and exothermic region with increasing surfactant concentration. The endothermic part can be looked upon as an incremental binding isotherm and reflects the number of surfactant molecules involved in the association process. The exothermic region features inverse hydrophobic bonding behaviour. This is related to the flexible nature of the adsorbent, i.e. the polymer. Electrostatic repulsion between neighbouring surfactant molecules causes at increased surfactant concentrations structural rearrangements of the polymer-surfactant complexes. This is accompanied by losing inter- and intrachain linking and entropy gain since the expanded complexes can move more freely. Additional surfactants continue to adsorb on the vacant hydrophobic adsorption sites. The influence of the initial amount of polymer and the electrolyte concentration support our proposals.     

Radiation chemistry of aqueous poly(ethylene oxide) solutions. I

The γ radiolysis of aqueous high molecular weight poly(ethylene oxide) solutions has been studied. The crosslinking and eventual gelation of these solutions appears to occur via an indirect effect. Solubility measurements on the gelled solutions showed that the ratio of crosslinking to degradation is about four. G(H₂) increased from 1.3 in neutral solutions to 3.5 in 0.1N HCl solutions. In heavy water solutions, HD is the major gaseous product. Solvated electrons are not important precursors to hydrogen at neutral pH. Intramolecular crosslinking appears to be an important phenomenon in solutions of high molecular weight polymers.     

The conformational stability of tactic poly(2-hydroxyethyl methacrylate) in aqueous salt solutions

The conformational stability of tactic poly(2-hydroxyethyl methacrylate) (PHEMA) in aqueous salt solutions was investigated by measurements of swelling, surface-free energy, and differential scanning calorimetry, as this polymer in water is sensitive in various electrolytes. In the case of inorganic salts, the major role for the salt effect is played by the anions, and the exposure of hydrophobic components at the PHEMA surface can be correlated with the increase of the degree of swelling. The influence of cations is considerably weaker. In the case of organic salts, tetraalkylammonium halides cause the chain extension more effectively with the increase of alkyl chain length in the cations. This result indicates that the breakdown of the hydrophobic parts in PHEMA provides an important clue on conformational stability. The amount of water molecules bound with the hydrophilic sites of tactic-PHEMA mainly depends on the chain extension and the hydration of cations. Since the sites in tactic-PHEMA influenced by the cation and the anion are different, their effects cause the conformational transition at a specific range of salt concentration. © 1993 John Wiley & Sons, Inc.     

Dilute solution properties of poly(dimethyldiallylammonium chloride) in aqueous sodium chloride solutions

MW fractions of poly(dimethyldiallylammonium chloride) (PDMDAAC) were prepared by preparative size-exclusion chromatography and characterized by static and dynamic light scattering, viscometry, size-exclusion chromatography, and electrophoretic light scattering, in 0.50M NaCl solution. The behavior of fractions with MW < 2 × 10⁵ was as expected for a strong polyelectrolyte in a good solvent, with a Mark-Houwink exponent of ca. 0.8, and MW-dependencies of the hydrodynamic radius and the radius of gyration of corresponding magnitude. At higher MW, curvature appears in the MW-dependencies, which can be best explained by the presence of branching. While this notably lowers the intrinsic viscosity at high MW, the electrophoretic mobility is unchanged regardless of molar mass. Thus, the branched polymers display the electrophoretic free-draining behavior characteristic of linear polyelectrolytes. ©1995 John Wiley & Sons, Inc.     

Flow properties of poly(methyl methacrylate) solutions

Viscosity and normal stress behavior were measured for poly(methyl methacrylate) samples of various average molecular weights in diethyl phthalate solution at 30 and 60°C. All samples conformed approximately to the most probable distriution (M?_w/M?_n = 2). Concentrations ranged from 0.113 to 0.38 g/ml, and M?_w from 53,800 to 1,620,000. Despite considerable evidence in the literature of unusual linear viscoelastic behavior for this polymer, its nonlinear properties appear to be rather conventional. The viscosity–shear rate master curve was similar to that found earlier for concentrated solutions of polystyrene and poly(vinyl acetate) of comparable molecular-weight distribution. The viscosity time constant τ_o parallels τ_R, the characteristic time of the Rouse model, although the residual dependence of τ_o/τ_R on concentration and molecular weight appears to be slightly different from that for polystyrene and poly(vinyl acetate). Similar conclusions apply to the recoverable compliance J_e,^o estimated from the normal stress behavior of each solution, and its relationship to the Rouse model compliance J_R.     

A small-angle neutron scattering study of poly(ethylene oxide) microstructure in aqueous poly(styrenesulfonate sodium) solutions

Dilute aqueous solutions of d-PEO and PSSNa mixtures were studied by (2)H NMR spectroscopy and small-angle neutron scattering (SANS). The interactions between d-PEO and PSSNa were found to be negligible both in the presence and absence of NaCl. At very dilute concentration (0.7 mg mL(-1)), d-PEO chains were still found to be slightly collapsed at ambient temperature in water. Upon the addition of PSSNa, aggregates of d-PEO were observed with d-PEO coils loosely associated with each other. The average centre to centre distance between d-PEO coils, which was calculated from the maxima in SANS spectra, was similar to the size of the individual coils. The effect of a simple salt, NaCl, on d-PEO-PSSNa interaction was investigated. Salt addition induced a breakdown of the dilute d-PEO aggregates.     

亚砜类非离子型表面活性剂在固/液界面上的吸附I: 硅胶/水溶液界面上的吸附

测定了癸基和辛基-甲亚基亚砜在硅胶/水溶液界面的吸附以及溶液在石英界面的接触角. 研究了温度和pH值对吸附的影响. 吸附等温线似应归入Giles分类的L4型. 饱和吸附层的平均分子面积为27-30A^2. 二个同系物的γ/γ-c/cmc曲线彼此重叠. 吸附温度系数在低浓度范围是负性的在高浓度范围是正性的. 接触角的测量表面吸附使硅胶表面疏水. 从实验结果考虑到吸附过程由二个阶段组成: 一是在低浓度范围由固体表面和亚砜基之间的相互作用, 另一过程是在高浓度范围中, 被吸附的表面活性剂分子及其在溶液中的疏水作用.     

Thermoresponsive characteristics of fluoroalkyl end-capped co-oligomers in aqueous solutions and on the poly(methyl methacrylate) film surface

Fluoroalkyl end-capped N-(1,1-dimethyl-3-oxobutyl)acrylamide--acryloylmorpholine co-oligomers were prepared by the co-oligomerizations of fluoroalkanoyl peroxides with the corresponding monomers. These fluorinated co-oligomers exhibited a lower critical solution temperature (LCST) characteristic in aqueous solutions. Of particular interest, a steep time dependence of contact angle values for dodecane was observed from 40 to 60 degrees C to decrease their values, effectively, on the modified PMMA [poly(methyl methacrylate)] film surface treated with fluorinated co-oligomer possessing the LCST: 36 degrees C (in water), although such a steep time dependence was not observed from 20 to 30 degrees C.     

Investigation of adsorption behaviour of mercury in microamounts on manganese dioxide from aqueous solutions

Adsorption of mercury onto manganese dioxide was studied in relation to the concentrations of electrolyte, adsorbent and adsorbate and foreign ions. Adsorption of other metal ions under similar conditions was also measured. Adsorption decreases with increasing electrolyte concentration. Thiosulfate, thiocyanate, iodide and all cations tested suppress the adsorption; the greater the ionic potential of cation, the weaker the adsorption of mercury. Adsorption follows the Freundlich-type isotherm over a wide range of mercury concentration (10^–7–10^–8 g·ml^–1). 98% of the adsorbed mercury can be eluted from the oxide column with 60 ml of 3M nitric acid solution.     

Swelling of poly(ethylene oxide) gel in aqueous solutions of sodium dodecyl sulfate with added sodium chloride

The swelling behavior of poly(ethylene oxide) (PEO) gels in aqueous solutions of sodium dodecyl sulfate (SDS) with and without NaCl was investigated. In the absence of NaCl, PEO gels with different degrees of cross-linking began to swell from a concentration lower than the critical micelle concentration (cmc) of SDS, then showed sigmoidal enhancements of swelling in a higher SDS concentration region until the degrees of swelling reached maximum values. The SDS concentration at which the swelling began to appear was in reasonable agreement with the critical aggregation concentration (cac) value reported for the aqueous PEO system. For the cases where NaCl was present, the swelling behavior of PEO gel was different from that when NaCl was absent in the following way. The concentrations where the swelling begins to appear, and hence those where the degree of swelling rises steeply, decreased with an increase in NaCl concentration. The ultimate degrees of swelling at higher concentration regions also decreased with an increase in the NaCl concentration. The lowering of the SDS concentrations at which the PEO gel began to swell is in line with the decreases in the cmc of SDS solutions containing NaCl and also with the decreases in the cac of PEO solution. Electronic Publication     

Thermodynamics of aqueous solutions containing poly (N-isopropylacrylamide)

Hydrogels undergo reversible and discontinuous volume changes in response to variation of solution conditions such as solvent composition, temperature, salt concentration, and pH. In this contribution we focus our attention on the experimental and theoretical investigation of these swelling equilibria of aqueous cross-linked poly (N-isopropylacrylamide) solutions as well as on the connected demixing behavior of the linear polymer dissolved in water. For the experimental study of the (liquid + liquid) equilibrium an alternative method based on refractive index measurements is suggested. In order to calculate the swelling behavior a model combining an expression for the Gibbs free energy of mixing with an expression for the elastic network is applied. As a model for the Gibbs free energy of mixing the UNIQUAC-approach and the Koningsveld–Kleintjens model are used. For the elastic network contribution again two different theories, namely the phantom network theory and the affine network theory, were applied. Whereas the type of network theory has only a small influence on the calculation results, the Gibbs free energy of mixing has a large impact. Using the UNIQUAC-approach the swelling equilibria can be correlated close to the experimental data, however, this model predicts a homogeneous mixture for linear polymer chains in water. In contrast to this situation the Koningsveld–Kleintjens model does a good job in calculating the swelling equilibria as well as the demixing curve, however, the adjustable parameter must be changed slightly.     

Synthesis of densely branched poly(methyl methacrylate)s via ATR copolymerization of methyl methacrylate and ethylene glycol dimethacrylate

Densely branched poly(methyl methacrylate)s have been synthesized by copolymerization of methyl methacrylate (MMA) and ethylene glycol dimethacrylate (EGDMA) using atom transfer free radical polymerization (ATRP). By employing the phenyl and benzyl esters of 2-bromo-2-methylpropionic acid as the initiators with 2,2-bipyridyl and Cu(I)Cl it has been possible to use high field ¹H nuclear magnetic resonance spectroscopy to evaluate in some detail the composition and structure of the branched PMMAs obtained. Parallel molar mass size exclusion chromatographic analysis using a multi-angle light scattering detector with a refractive index detector (MALS/SEC) has allowed the branched architecture of the products to be confirmed. Rather remarkably, high yields of branched PMMAs can be obtained without crosslinking using MMA/EGDMA molar feed ratios of up to 5/1 by appropriate adjustment of the molar feed of initiator. In particular by maintaining the EGDMA/initiator molar feed ratio ∼1/1 fully soluble products can be obtained that are densely branched since this feed ratio ensures that on average each living primary chain initiated contains on average only one branching EGDMA segment. As might be expected this controlled free radical process offers better control in the synthesis of branched polymer than the corresponding system we have reported using conventional free radical polymerization, and unlike the latter which requires the use of a chain transfer agent, the ATRP system requires no additional chain regulating component. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2375–2386, 2007     

Conformational phase diagram of poly(l-lysine) in sodium alkanesulfonate aqueous solutions at various temperatures

The conformation of poly(l-lysine) (PLL) was investigated in sodium alkanesulfonate C_nSO₃Na (n=8, 7) at various temperatures by circular dichroism spectrum measurements. C₈SO₃Na induced a double-step conformational change from a coil, to a β-sheet, and then to an α-helix, in which C₇SO₃Na induced a single-step coil-to-helix conformational change. Binding isotherms of C₈SO₃Na by PLL were constructed from the potentiometry of equilibrium concentration of the surfactant using a surfactant ion-selective electrode. The curves indicated the cooperative binding characteristic and were analyzed by a linear lattice model using the Bethe approximation. The thermodynamic parameters obtained from the model revealed that the binding of C₈SO₃Na by PLL was an entropy-driven process. The conformational change was observed at nearly full binding, presumably due to the surfactant clustering of the ordered conformation.