Fabrication of Dual-Wavelength Fiber Bragg Grating with a Longitudinal Stretch

A method of fabricating dual-wavelength fiber Bragg grating with a uniform phase mask is demonstrated. Theoretical analysis and numerical simulation using Matrix method are given. The moving exposing technique is adopted. Good control over the grating’s reflectivity and the separation of the two Bragg wavelengths is enabled by adjusting the stretch, the length of the grating, and the exposure. A grating with two equal transmission peaks of 19.5 dB is obtained by using this method, and the separation of the two Bragg wavelengths is 0.78 nm. Translated from Chinese Journal of Quantum Electronics, 2005, 22(1) (in Chinese)     

Tunable dual-wavelength fiber laser based on a single fiber Bragg grating in a Sagnac loop interferometer

We propose a simple dual-wavelength Er-doped fiber laser configuration based on a dual-wavelength fiber Bragg grating written on the splice joint between two different fibers for wavelength-selective filter in the Sagnac loop interferometer. The wavelength separation between the adjacent lasing wavelengths is 1.12 nm and the side-mode suppression ratio (SMSR) is over 55 dB. The output power variation is less than 0.8 dB over a two-minute period. Moreover, the lasing wavelength can be effectively tuned using the thermal heating method.     

双波长啁啾相移光纤光栅

理论研究并实验验证了一种含有两段π相移的啁啾相移光纤光栅.采用F矩阵对啁啾相移光纤光栅进行计算并分析了该光栅的谱特性.含有两段π相移的啁啾相移光纤光栅可以在普通啁啾光栅透射谱阻带中产生双波长透射峰,透射峰位置直接取决于光栅中π相移的位置,透射峰的线宽和透射峰的波长间隔没有关系,仅随着啁啾率的增大而增大.采用带相位掩模的逐点扫描法对含有两段π相移的双波长啁啾相移光栅进行了制作,获得波长间隔为8 nm的双波长透射谱的光栅器件.该光栅的消光比和3 dB谱线宽分别为20 dB和0.08 nm,实验结果和理论设计一致.     

Microwave generation using an all polarization-maintaining linear cavity dual-wavelength fiber laser with tunable wavelength spacing

A stable dual-wavelength erbium-doped fiber laser with a linear cavity is formed by a polarization-maintaining uniform fiber Bragg grating (PM-FBG) and a polarization-maintaining linearly chirped fiber Bragg grating (PM-LCFBG), both of which were fabricated on a high-birefringence (Hi-Bi) fiber. Experimental results show stable dual-wavelength lasing operation with a wavelength separation of ∼0.22 nm, which can be tuned down to as small as 0.05 nm and a large optical signal-to-noise ratio (OSNR) of over 40 dB under room-temperature. Microwave signal at frequency of 9.41, 18.03 and 27.46 GHz is achieved by heterodyned the output lasing wavelengths on a photodetector.     

A stable dual-wavelength fiber laser with tunable wavelength spacing using a polarization-maintaining linear cavity

We propose and experimentally demonstrate a stable dual-wavelength erbium-doped polarization-maintaining (PM) fiber laser with tunable wavelength spacing using an all-PM linear cavity that makes use of two reflection peaks from the PM fiber Bragg grating (PM-FBG). Experimental results show stable dual lasing lines with a wavelength separation of ∼0.22 nm and a large optical signal-to-noise ratio (OSNR) of over 40 dB under room temperature. By applying axial strain to the PM-FBG, the center wavelengths of the two lasing lines can be tuned over several nanometers and the wavelength separation between the lasing lines can also be tuned to as small as 0.05 nm, which, to our knowledge, is the smallest wavelength spacing ever obtained from a stable room-temperature dual-wavelength fiber laser. The proposed laser configuration has the advantages of simple structure, low loss, stable dual-wavelength operation and a very small lasing linewidth of ∼5 kHz . PACS 42.55.Wd; 42.81.-i; 42.81.Gs     

Switchable dual-wavelength Erbium-doped fiber ring laser with cascaded fiber Bragg gratings

We have experimentally shown wavelength mode switching in a dual-wavelength Erbium-doped single cavity fiber laser where the initial two wavelengths of 1 nm spacing are determined by the cascaded reflection type short-period fiber Bragg gratings having two different centre wavelengths of 1550.5 and 1551.5 nm. The lasing mode depends on the polarization in the ring cavity to migrate from one wavelength to another or operates in both modes in a polarization beam splitter output. To effectively control the polarization in the ring cavity, the polarization controllers were positioned before and after the polarization beam splitter. This method of wavelength switching provides a simple way of mode tuning in dual-wavelength fiber lasers.     

Tunable microwave photonic notch filter using a dual-wavelength fiber laser with phase modulation

A novel tunable microwave photonic notch filter using a phase-modulated dual-wavelength fiber laser is presented. A stable dual-wavelength erbium-doped fiber laser with a linear cavity is formed by a polarization-maintaining uniform fiber Bragg grating (PM-FBG) and a polarization maintaining linearly chirped fiber Bragg grating (PM-LCFBG), both of which were fabricated on a high-birefringence (Hi-Bi) fiber. It is found that a stable room-temperature dual-wavelength operation can be achieved due to the presence of two reflection peaks arising from the orthogonal states of polarization (SOP) of the PM-FBG. Experimental results show stable dual-wavelength lasing operation with a wavelength separation of ∼0.36 nm and a large optical signal-to-noise ratio (OSNR) of over 40 dB under room temperature. The dual-wavelength fiber laser is combined with a phase modulator and a segment of single-mode fiber (SMF) as a dispersive device to form a tunable microwave photonic notch filter. By stretching the PM-FBG to tune the wavelength separation of the dual-wavelength fiber laser, a tunable microwave photonic notch filter with various free spectral ranges (FSRs) and a rejection ratio greater than 35 dB was developed.     

Wavelength spacing tunable dual-wavelength single-longitudinal-mode fiber ring laser based on fiber Bragg gratings

A wavelength spacing tunable dual-wavelength single-longitudinal-mode fiber ring laser is presented by employing separated fiber Bragg gratings. By using a saturable-absorption-induced grating filter and a hybrid gain medium formed by a semiconductor optical amplifier and an erbium-doped fiber amplifier, stable single-longitudinal-mode lasing is achieved at room temperature. Wavelength spacing of the proposed fiber laser can be tuned in a range from 0.1 to 1.3 nm.     

Wavelength-spacing tunable multiwavelength erbium-doped fiber laser based on four-wave mixing of dispersion-shifted fiber

We experimentally demonstrate a wavelength-spacing tunable multiwavelength erbium-doped fiber laser based on degenerate four-wave mixing in a dispersion-shifted fiber incorporating multiple-fiber Bragg gratings. We have achieved stable operation of the multiwavelength erbium-doped fiber laser, which has 0.8 nm spacing ten-channel lasing wavelengths and a high extinction ratio of more than approximately 45 dB, at room temperature. The output power of the multiwavelength erbium-doped fiber laser is stable, so the peak fluctuation is less than approximately 0.2 dB. By changing the properties such as loss and polarization state of multiple fiber Bragg grating cavities, we can exercise flexible control of the wavelength spacing of the multiwavelength output. We can also obtain switchable multiwavelength lasing operation by elimination of the effects of alternate single-fiber Bragg gratings.     

Tunable dual-wavelength fiber laser based on a polarization-maintaining fiber Bragg grating and a Hi-Bi fiber optical loop mirror

We demonstrate experimentally the operation of a linear cavity dual-wavelength fiber laser using a polarization maintaining fiber Bragg grating (PM-FBG) as an end mirror that defines two closely spaced laser emission lines. The PM-FBG is also used to tune the laser wavelengths. The total tuning range is ∼8 nm. The laser operates in a stable dual-wavelength mode for an appropriate adjustment of the cavity losses for the generated wavelengths. The high birefringence (Hi-Bi) fiber optical loop mirror (FOLM) is used as a tunable spectral filter to adjust the losses. The FOLM adjustment was performed by the temperature control of the Hi-Bi fiber.     

A simple linear cavity dual-wavelength fiber laser using AWG as wavelength selective mechanism

In this paper, a simple design of linear cavity dual-wavelength fiber laser (DWFL) is proposed. Operating in the C-band region stretching from 1538.3 nm to 1548.6 nm, an arrayed waveguide grating (AWG) is used to generate the dual-wavelengths output together with a broadband fiber Bragg grating as a back reflector and an optical circulator with a 10% output coupling ratio which acts as a front mirror. The measured average output power of the DWFL is about −5.66 dBm and with a side mode suppression ratio (SMSR) of 53.1 dB. The spacing between the two output wavelengths can be varied from 0.8 nm to 10.3 nm with a stable output and minimum power fluctuations.     

Variable Wavelengths Fiber Bragg Gratings Written with A Phase Mask and Four Prisms

1　Ｉｎｔｒｏｄｕｃｔｉｏｎ　　Ｓｉｎｃｅｔｈｅｆｉｂｅｒｗａｓｐｌａｃｅｄｄｉｒｅｃｔｌｙｂｅｈｉｎｄｔｈｅ ｐｈａｓｅｍａｓｋ ,ｗｈｉｃｈｗａｓｏｒｉｇｉｎａｌｌｙｄｅｍｏｎｓｔｒａｔｅｄｂｙＫ .Ｏ .Ｈｉｌｌｅｔａｌ.ｉｎ 1 993[1] ,ｔｈｉｓｍｅｔｈｏｄｈａｓｂｅｅｎｕｓｅｄｗｉｄｅｌｙｆｏｒｗｒｉｔｉｎｇｆｉｂｅｒＢｒａｇｇ ｇｒａｔｉｎｇ .Ｈｏｗｅｖｅｒ ,ｔｈｅｃｏｎｔａｃｔｔｅｃｈｎｉｑｕｅｏｆｐｈａｓｅｍａｓｋｃａｎｏｎｌｙｉｎｓｃｒｉｂｅｔｈｅｆｉｂｅｒＢｒａｇｇ ｇｒａｔｉｎｇｗｉｔｈ…     

Variable Wavelengths Fiber Bragg Gratings Written with A Phase Mask and Four Prisms

Using only one diffractive element, the Talbot interferometer provides a robust and inherently stable method for reproducing fiber Bragg gratings with variable wavelengths, and reduces the complexity of the fiber grating fabrication system. However, the usable length of the grating is limited by the practical length of the mirrors. This paper presents a phase mask with two fixed prisms and two rotational prisms to inscribe fiber Bragg gratings with variable Bragg wavelengths. In this system, the fiber Bragg grating is inscribed by UV interference stripes of 193 nm derived from two rotational prisms and two fixed prisms, where phase mask is used as a beam splitter of ±1 order diffraction light. It is noteworthy that the tunable phase mask interferometer decreases the demand of the length of prism evidently.     

利用倾斜光纤光栅的可开关双波长光纤激光器

报导了一种在四波混频作用下利用倾斜光纤布拉格光栅进行波长选择的可开关双波长掺铒光纤激光器。通过将倾斜光纤光栅与单模光纤进行横向错位焊接,使光栅的反向LP01和LP11两个模式具有相近的有效反射率,从而可以用来进行激光器的双波长选择。接入腔内的一段高非线性光子晶体光纤引入的四波混频效应克服了模式竞争,使得双波长激光在室温下稳定振荡。腔内起偏器和偏振控制器的联合作用可产生依赖于波长的损耗,以补偿光纤光栅两反射峰峰值的大小差异。基于以上原理,通过调节腔内的偏振态,该激光器实现了室温下稳定的双波长输出,也实现了在两波长之间的转换。两波长激光均有超过45 dB的信噪比,最大的功率波动为0.8 dB     

Stable dual-wavelength single-longitudinal-mode ring erbium-doped fiber laser for optical generation of microwave frequency

We demonstrate a simple dual-wavelength ring erbium-doped fiber laser operating in single-longitudinal-mode (SLM) at room temperature. A pair of reflection type short-period fiber Bragg gratings (FBGs), which have two different center wavelengths of 1545.072 and 1545.284 nm, are used as the wavelength-selective component of the laser. A segment of unpumped polarization maintaining erbium-doped fiber (PM-EDF) is acted as a narrow multiband filter. By turning the polarization controller (PC) to enhance the polarization hole burning (PHB), the single-wavelength and dual-wavelength laser oscillations are observed at 1545.072 and 1545.284 nm. The output power variation is less than 0.6 dB for both wavelengths over a five-minute period and the optical signal to noise ratio (OSNR) is greater than 50 dB. By beating the dual-wavelengths at a photodetector (PD), a microwave signal at 26.44 GHz is demonstrated.     

Actively mode-locked dual-wavelength fiber laser with close wavelength spacing using a fiber Bragg grating

A simple actively mode-locked fiber ring laser is proposed and successfully demonstrated to generate dual-wavelength picosecond pulses with close wavelength spacing using one Bragg grating in standard single-mode fiber. The proposed laser can be made to operate in stable dual-wavelength at room temperature, due to the birefringence characteristic of the FBG induced by transverse strain. Transverse strain loading on the FBG allows the wavelength spacing to be controlled. Generation of stable dual-wavelength pulses with a pulsewidth of 212–234 ps and a tunable wavelength separation from 0.2 to 0.44 nm at a pulse rate of 1.05 GHz was demonstrated.     

Incorporate, switchable dual-wavelength fiber laser with Bragg gratings written in a polarization-maintaining erbium-doped fiber

A stable, incorporate and switchable dual-wavelength fiber laser with two fiber Bragg gratings written in a photosensitive and polarization-maintaining erbium-doped fiber directly, that is, without splices in the laser cavity, is proposed and demonstrated. Simultaneous dual-wavelength oscillation is achieved at room temperature with a wavelength spacing of 0.343 nm. The power fluctuation and wavelength shift of single-wavelength oscillations are measured to be less than 0.24 dB and 0.013 nm over 2 h. The wavelength switchability between single- and dual-wavelength oscillations is realized by altering the voltage upon the electrostrictive ceramic actuator.     

Switchable dual-wavelength passively mode-locked fiber ring laser using SESAM and cascaded fiber Bragg gratings

We propose and demonstrate an efficient and simple wavelength switchable dual-wavelength passively mode-locked fiber ring laser based on a semiconductor saturable absorber mirror (SESAM) and a cascaded sequence of fiber Bragg gratings (FBGs). The efficient self-starting mode-locked operation was realized with a SESAM. Dual-wavelength pulses with a wavelength spacing of 12.49 nm were obtained which was determined by the reflection peaks of the FBGs used in the experiment. In addition, by rotating the polarization controllers (PCs), the switchable dual-wavelength operation was simply achieved via exploiting wavelength-dependent loss mechanism.     

取样布拉格光纤光栅的传输矩阵

根据在一般坐标系下均匀布拉格光纤光栅的传输矩阵,得到了取样布拉格光纤光栅的传输矩阵。利用傅里叶变换得到了取样布拉格光纤光栅的谐振方程。结果表明,在不考虑平均折射率变化的情况下,谐振峰的位置是由光栅的周期和取样周期共同确定的,与取样时的占空比、光栅长度和耦合系数没有关系。类似于物理光栅,取样布拉格光纤光栅也存在缺级现象,给出了出现缺级的条件。     

Theoretical analysis of novel fiber grating pair

A novel fiber grating pair that consists of a conventional long-period fiber grating and a fiber Bragg cladding grating (FBCG) is proposed. The FBCG is a new type of fiber grating in which refractive index modulation is formed in the cladding. Through the coupled-mode theory, we accurately calculate the coupling coefficients between modes supported in the fibers. And some other mode coupling features in the fiber cladding gratings are analyzed in detail. The calculation of the modes involved in this paper is based on a model of three-layer step-index fiber geometry. Then, we have investigated the sensitivity characteristics for variation of the modulation strengths of the fiber Bragg cladding gratings’ resonance peaks and the long-period cladding gratings’ (LPCGs) dual resonant peaks. Finally, the modulation strength sensitivity of the grating pair’s three resonant peaks is demonstrated, and the results indicate that these grating pairs may find potential applications in optical fiber sensing.