Lab on valve-multisyringe flow injection system (LOV-MSFIA) for fully automated uranium determination in environmental samples

The hyphenation of lab-on-valve (LOV) and multisyringe flow analysis (MSFIA), coupled to a long path length liquid waveguide capillary cell (LWCC), allows the spectrophotometric determination of uranium in different types of environmental sample matrices, without any manual pre-treatment, and achieving high selectivity and sensitivity levels. On-line separation and preconcentration of uranium is carried out by means of UTEVA resin. The potential of the LOV-MSFIA makes possible the fully automation of the system by the in-line regeneration of the column. After elution, uranium(VI) is spectrophotometrically detected after reaction with arsenazo-III. The determination of levels of uranium present in environmental samples is required in order to establish an environmental control. Thus, we propose a rapid, cheap and fully automated method to determine uranium(VI) in environmental samples. The limit of detection reached is 1.9 ηg of uranium and depending on the preconcentrated volume; it results in ppt levels (10.3 ηg L⁻¹). Different water sample matrices (seawater, well water, freshwater, tap water and mineral water) and a phosphogypsum sample (with natural uranium content) were satisfactorily analyzed.     

Automated determination of uranium(VI) at ultra trace levels exploiting flow techniques and spectrophotometric detection using a liquid waveguide capillary cell

Rapid and fully automated multisyringe flow-injection analysis (MSFIA) with a multi-pumping flow system (MPFS) coupled to a long path-length liquid waveguide capillary cell (LWCC) is proposed for the determination of uranium(VI) at ultra trace levels. On-line separation and pre-concentration of uranium is carried out by means of a TRU resin. After elution, uranium(VI) is spectrophotometrically detected after reaction with arsenazo-III. Combination of the MSFIA and MPFS techniques with the TRU-resin enables the analysis to be performed in a short time, using large sample volumes and achieving high selectivity and sensitivity levels. A detection limit of 12.6 ng L⁻¹ (ppt) is reached for a 100-mL sample volume. The versatility of the proposed method also enables pre-concentration of variable sample volumes, enabling application of the analysis to a wide concentration range. Reproducibility of better than 5% and a resin durability of 40 injections should be emphasized. The developed method was successfully applied to different types of environmental sample matrices with recoveries between 95 and 108%.     

Solid phase extraction and preconcentration of uranium(VI) and thorium(IV) on Duolite XAD761 prior to their inductively coupled plasma mass spectrometric determination

A simple and effective method is presented for the separation and preconcentration of thorium(IV) and uranium(VI) by solid phase extraction on Duolite XAD761 adsorption resin. Thorium(IV) and uranium(VI) 9-phenyl-3-fluorone chelates are formed and adsorbed onto the Duolite XAD761. Thorium(IV) and uranium(VI) are quantitatively eluted with 2 mol L⁻¹ HCl and determined by inductively coupled plasma-mass spectrometry (ICP-MS). The influences of analytical parameters including pH, amount of reagents, amount of Duolite XAD761 and sample volume, etc. were investigated on the recovery of analyte ions. The interference of a large number of anions and cations has been studied and the optimized conditions developed have been utilized for the trace determination of uranium and thorium. A preconcentration factor of 30 for uranium and thorium was achieved. The relative standard deviation (N = 10) was 2.3% for uranium and 4.5% for thorium ions for 10 replicate determinations in the solution containing 0.5 μg of uranium and thorium. The three sigma detection limits (N = 15) for thorium(IV) and uranium(VI) ions were found to be 4.5 and 6.3 ng L⁻¹, respectively. The developed solid phase extraction method was successively utilized for the determination of traces thorium(IV) and uranium(VI) in environmental samples by ICP-MS.     

Extraction studies of uranium into a third-phase of thorium nitrate employing tributyl phosphate and <Emphasis Type="Italic">N,N</Emphasis>-dihexyl octanamide as extractants in different diluents

Extraction behavior of 1 × 10⁻²–0.1 M U(VI) from aqueous phases containing 0.86 M Th(IV) at 4 M HNO₃ in 1.1 M tributyl phosphate (TBP) and 1.1 M N,N-dihexyl octanamide (DHOA) solutions in different diluents viz. n-dodecane, 10% 1-octanol + n-dodecane, and decahydronaphthalene (decalin) was studied. Third-phase formation was observed in both the extractants using n-dodecane as diluent. There was a gradual decrease in Th(IV) concentration in the third-phase (heavy organic phase, HOP) with increased aqueous U(VI) concentration [0.71 M (no U(VI))–0.61 M (0.1 M U(VI)) for TBP; 0.27 M (no U(VI))–0.22 M (0.1 M U(VI)) for DHOA]. The HOP volume in case of DHOA was ~2.2 times of that of TBP. Uranium concentration in HOP increased with its initial concentration in the aqueous phase [from 1.8 × 10⁻² M (0.01 M U(VI))–0.162 M (0.1 M U(VI)) for TBP; from 1.4 × 10⁻² M (0.01 M U(VI))–0.14 M (0.1 M U(VI)) for DHOA] suggesting that Th(IV) was being replaced by U(VI). An empirical correlation was developed for predicting the concentrations of uranium and thorium in HOP for both the extractants. No third-phase appeared during the extraction of uranium and thorium from the aqueous phases employing 10% 1-octanol + n-dodecane, or decalin as diluents, and therefore, were better choices as diluent for alleviating the third-phase formation during the reprocessing of spent thorium based fuels, and for the recovery of thorium from high-level waste solutions.     

<Emphasis Type="Italic">p</Emphasis>-<Emphasis Type="Italic">tert</Emphasis>-Butylcalix[8]arene loaded silica gel for preconcentration of uranium(VI) via solid phase extraction

This paper reports silica gel loaded with p-tert-butylcalix[8]arene as a new solid phase extractor for determination of trace level of uranium. Effective extraction conditions were optimized in column methods prior to determination by spectrophotometry using arsenazo(III). The results showed that U(VI) ions can be sorbed at pH 6 in a mini-column and quantitative recovery of U(VI) (>95–98%) was achieved by stripping 0.4 mol L⁻¹ HCl. The sorption capacity of the functionalized sorbent is 0.072 mmol uranium(VI) g⁻¹ modified silica gel. The relative standard deviation and detection limit were 1.2% (n = 10) for 1 μg uranium(VI) mL⁻¹ solution and 0.038 μg L⁻¹, respectively. The method was employed to the preconcentration of U(VI) ions from spiked ground water samples.     

Preconcentration of uranium(VI) and thorium(IV) from aqueous solutions using low-cost abundantly available sorbent

Olive cake as low-cost abundantly available sorbent has been characterized by N₂ at 77 K adsorption, porosity analysis, elemental analysis and IR spectra and has been used for preconcentrating of uranium(VI) and thorium(IV) ions prior to their determination spectrophotometrically. The optimum pH values for quantitative sorption of U(VI) and Th(IV) are 4–7 and 3–7, respectively. The enrichment factor for the preconcentration of U(VI) and Th(IV) were found to be 125 and 75 in the given order. The sorption capacity of olive cake is in the range of 2,260–15,000 μg g⁻¹ for Th(IV) and in the range of 1,090–17,000 μg g⁻¹ for U(VI) at pH 3–7. The sorbent exhibits good reusability and the uptake and stripping of the studied ions were fairly rapid. The elution of U(VI) and Th(IV) was performed with 0.3–1 M HCl/1–2 M HNO₃ and 0.3–0.8 M HCl/1 M HNO₃, respectively. The precision of the method was 1.8 RSD% for U(VI) and 2.5 RSD% for Th(IV) in a concentration of 1.00 μg mL⁻¹ for 10 replicate analysis. The influence of some electrolytes and cations as interferents was discussed. Separation of U(VI) and Th(IV) from other metal ions in synthetic solution was achieved.     

Separation and quantitative determination of dioxouranium(VI) and thorium(IV) ions in the presence of different metallic ions by TLC using iso-propyldithiophosphoric acid as complexing agent

The separation of uranium and thorium from matrices containing various metal ions, was studied. The mobile phase contains isopropyldithiophosphoric acid (i-PrDTP), as a complexing agent, in order to differentiate the studied species by modifying their retention. The paper reports the successful separation and the quantitative determination of uranium and thorium in the presence of Ni²⁺, Co²⁺ and Ag⁺ in the concentration range 2.5–2.5 μg/μl for uranium and 2.5–30 μg/μl for thorium.     

Simultaneous extraction and preconcentration of uranium and thorium in aqueous samples by new modified mesoporous silica prior to inductively coupled plasma optical emission spectrometry determination

A new synthesized modified mesoporous silica (MCM-41) using 5-nitro-2-furaldehyde (fural) was applied as an effective sorbent for the solid phase extraction of uranium(VI) and thorium(IV) ions from aqueous solution for the measurement by inductively coupled plasma optical emission spectrometry (ICP OES). The influences of some analytical parameters on the quantitative recoveries of the analyte ions were investigated in batch method. Under optimal conditions, the analyte ions were sorbed by the sorbent at pH 5.5 and then eluted with 1.0 mL of 1.0 mol L⁻¹ HNO₃. The preconcentration factor was 100 for a 100 mL sample volume. The limits of detection (LOD) obtained for uranium(VI) and thorium(IV) were 0.3 μg L⁻¹. The maximum sorption capacity of the modified MCM-41 was found to be 47 and 49 mg g⁻¹ for uranium(VI) and thorium(IV), respectively. The sorbent exhibited good stability, reusability, high adsorption capacity and fast rate of equilibrium for sorption/desorption of uranium and thorium ions. The applicability of the synthesized sorbent was examined using CRM and real water samples.     

Separation and preconcentration of Se(IV)/Se(VI) speciation on algae and determination by graphite furnace atomic absorption spectrometry in sediment and water

A novel method for the separation and preconcentration of Se(IV)/ Se(VI) with algae and determination by graphite furnace atomic absorption spectrometry (GFAAS) has been developed. The Se(VI) is extracted with algae from the solution containing Se(IV)/Se(VI) at pH 5.0, and the remaining Se(IV) is then preconcentrated pH 1.0. The detection limits (3σ, n = 11) of 0.16 μg L^–1 for Se(IV) and 0.14 μg L^–1 for Se(VI) are obtained using 40 mL of solution. At the 2.0 μg L^–1 level the relative standard deviation is 2.6% for Se(IV) and 2.3% for Se(VI). The method has been applied to the determination of Se(IV)/Se(VI) in sediment and water samples. Analytical recoveries of Se(IV) and Se(VI) added to samples are ?97 ± 5% and 102 ± 6% (95% confidence), respectively. Received: 10 February 1999 / Revised: 21 June 1999 / /Accepted: 22 June 1999     

Simultaneous spectrophotometric determination of trace amounts of uranium, thorium, and zirconium using the partial least squares method after their preconcentration by α-benzoin oxime modified Amberlite XAD-2000 resin

A new solid phase extraction method for separation and preconcentration of trace amounts of uranium, thorium, and zirconium in water samples is proposed. The procedure is based on the adsorption of U(VI), Th(IV) and Zr(IV) ions on a column of Amberlite XAD-2000 resin loaded with α-benzoin oxime prior to their simultaneous spectrophotometric determination with Arsenazo III using orthogonal signal correction partial least squares method. The enrichment factor for preconcentration of uranium, thorium, and zirconium was found to be 100. The detection limits for U(VI), Th(IV) and Zr(IV) were 0.50, 0.54, and 0.48 μg L⁻¹, respectively. The precision of the method, evaluated as the relative standard deviation obtained by analyzing a series of 10 replicates, was below 4% for all elements. The practical applicability of the developed sorbent was examined using synthetic seawater, natural waters and ceramic samples.     

Separation and determination of selenium in water samples by the combination of APDC coprecipitation: X-ray fluorescence spectrometry

A sensitive and non chromatographic analytical procedure for the separation of inorganic selenium species in natural water has been performed. A combination of APDC coprecipitation and determination by an absolute thin layer Energy dispersive X-ray fluorescence spectrometry method was used. The influence of various analytical parameters such as element concentration, oxidation states and pH on the recoveries of Se (IV) was examined. The presence of organic matter and bicarbonate anions, typical components in Cuban groundwater samples, was also tested. Negligible matrix effects were observed. At pH 4 a 100% recovery was found for Se (IV). The coprecipitation recovery of the oxidized selenium species (Se (VI)) was null for the selected concentration range (5–100 μg L⁻¹). When the Se (VI) was reduced by heating the solution with 4 mol L⁻¹ HCl, quantitative recovery was also obtained. The determination of total selenium was conducted by the application of the oxidation–reduction process and the analytical procedure for Se (IV). Se (VI) content was calculated as the difference between total selenium and Se (IV). The detection limit was 0.13 μg L⁻¹. The relative standard deviation was lower than 3.5% for 5 μg L⁻¹ of Se (IV). The trueness of the method was verified by using standardized hydride generation-atomic absorption spectrometry technique. The results obtained using the EDXRF technique were in good agreement with the ones determined by HG-AAS. The proposed method was applied to the determination of Se (IV) in surface water and groundwater samples.     

Development of reliable analytical method for extraction and separation of thorium(IV) by Cyanex 272 in kerosene

A simple and selective spectrophotometric method has been developed for the extraction and separation of thorium(IV) from sodium salicylate media using Cyanex 272 in kerosene. Thorium(IV) was quantitatively extracted by 5 × 10⁻⁴ M Cyanex 272 in kerosene from 1 × 10⁻⁵M sodium salicylate medium. The extracted thorium(IV) was stripped out quantitatively from the organic phase with 4.0 M hydrochloric acid and determined spectrophotometrically with arsenazo(III) at 620 nm. The effect of concentrations of sodium salicylate, extractant, diluents, metal ion and strippants has been studied. Separation of thorium(IV) from other elements was achieved from binary as well as multicomponent mixtures such as uranium(VI), strontium(II), rubidium(I), cesium(I), potassium(I), Sodium(I), lithium(I), lead(II), barium(II), beryllium(II) etc. Using this method separation and determination of thorium(IV) in geological and real samples has been carried out. The method is simple, rapid and selective with good reproducibility (approximately ±2%).     

Efficient uranium(VI) biosorption on grapefruit peel: kinetic study and thermodynamic parameters

The uranium(VI) biosorption by grapefruit peel was studied from aqueous solutions. Batch experiments was conducted to evaluate the effect of contact time, initial uranium(VI) concentration, initial pH, adsorbent dose, salt concentration and temperature. The equilibrium process was well described by the Langmuir, Redlich–Peterson and Koble–Corrigan isotherm models, with maximum sorption capacity of 140.79 mg g⁻¹ at 298 K. The pseudo second order model and Elovish model adequately describe the kinetic data in comparison to the pseudo first order model and the process involving rate-controlling step is much complex involving both boundary layer and intra-particle diffusion processes. The effective diffusion parameter D _i and D _f values were estimated at different initial concentration and the average values were determined to be 1.167 × 10⁻⁷ and 4.078 × 10⁻⁸ cm² s⁻¹. Thermodynamic parameters showed that the biosorption of uranium(VI) onto grapefruit peel biomass was feasible, spontaneous and endothermic under studied conditions. The physical and chemical properties of the adsorbent were determined by SEM, TG-DSC, XRD and elemental analysis and the nature of biomass–uranium (VI) interactions was evaluated by FTIR analysis, which showed the participation of COOH, OH and NH₂ groups in the biosorption process. Adsorbents could be regenerated using 0.05 mol L⁻¹ HCl solution at least three cycles, with up to 80% recovery. Thus, the biomass used in this work proved to be effective materials for the treatment of uranium (VI) bearing aqueous solutions.     

Studies on uranium recovery from inlet stream of Effluent Treatment Plant by novel “In-House” sorbent

A fast and simple multisyringe flow injection analysis (MSFIA) method for routine determination of thorium in water samples was developed. The methodology was based on the complexation reaction of thorium with arsenazo (III) at pH 2.0. Thorium concentrations were spectrophotometrically detected at 665 nm. Under optimal conditions, Beer’s law was obeyed over the range from 0.2 to 4.5 μg mL⁻¹ thorium, a 3σ detection limit of 0.05 μg mL⁻¹, and a 10σ quantification limit of 0.2 μg mL⁻¹ were obtained. The relative standard deviations (RSD, %) at 0.5, 2.5 and 4.5 μg mL⁻¹ was 2.8, 1.5 and 0.8%, respectively (n = 10). It was found that most of the common metal ions and anions did not interfere with the thorium determination. The proposed method was successfully applied to its analysis in various water samples.     

Flow injection on-line determination of uranium after preconcentration on XAD-4 resin impregnated with dibenzoylmethane

A flow injection on-line determination of uranium(VI) after preconcentration in a minicolumn having amberlite XAD-4 resin impregnated with dibenzoylmethane (DBM) is described. Uranium(VI) is selectively adsorbed from aqueous solution of pH 5.5 in the minicolumn (5.5 cm long with 5.0 mm i.d.) at a flow rate of 13.6 mL min⁻¹. The uranium(VI) complex was desorbed from the resin by 0.1 mol dm⁻³ HCl at a flow rate of 4.2 mL min⁻¹ and mixed with arsenazo-III solution (0.05% solution in 0.1 mol dm⁻³ HCl, 4.2 mL min⁻¹), and taken to the flow through cell of spectrophotometer where its absorbance was measured at 651 nm. Various parameters affecting the complex formation and its elution were optimized. Peak height (absorbance) was used for data analyses. The preconcentration factors of 36 and 143, detection limits of 0.9 and 0.232 μg L⁻¹, sample throughputs of 40 and 10 were obtained for preconcentration time of 60 and 300 s, respectively. The tolerance limits of many interfering cations like Th(IV) and rare-earth elements were improved. The proposed method was applied on different water (spiked tap, well and sea water) and biological samples and good recovery was obtained. The method was also validated on mocked uranium ore sample and the results were in good agreement with the reported value.     

Chromatographic separation of uranium(VI) from other elements using L-valine and poly[dibenzo-18-crown-6]

A selective and effective column chromatographic separation method has been developed for uranium(VI) using poly[dibenzo-18-crown-6]. The separation was carried out in L-valine medium. The adsorption of uranium(VI) was quantitative from 1.0 × 10⁻⁴ to 1 × 10⁻¹ M of L-valine. Amongst various eluents 2.0–8.0 M hydrochloric acid, 1.0–4.0 M sulfuric acid, 1.0–5.0 M perchloric acid, 6.0–8.0 M hydrobromic acid and 5.0–6.0 M acetic acid were found to be efficient eluents for uranium(Vl). The capacity of poly[dibenzo-18-crown-6] for uranium(VI) was 0.25 ± 0.01 mmol/g of crown polymer. Uranium(VI) was separated from number of cations and anions in binary mixtures in which most of the cations and anions show a very high tolerance limit. The selective separation of uranium(VI) was carried out from multicomponent mixtures. The method was extended to determination of uranium(VI) in geological samples. The method is simple, rapid and selective with good reproducibility (approximately ∼2%).     

Determination of total Sb,Se, Te,and Bi and evaluation of their inorganic species in garlic by hydride-generation–atomic-fluorescence spectrometry

A sensitive and simple analytical method has been developed for determination of Sb(III), Sb(V), Se(IV), Se(VI), Te(IV), Te(VI), and Bi(III) in garlic samples by using hydride-generation–atomic-fluorescence spectrometry (HG–AFS). The method is based on a single extraction of the inorganic species by sonication at room temperature with 1 mol L⁻¹ H₂SO₄ and washing of the solid phase with 0.1% (w/v) EDTA, followed by measurement of the corresponding hydrides generated under two different experimental conditions directly and after a pre-reduction step. The limit of detection of the method was 0.7 ng g⁻¹ for Sb(III), 1.0 ng g⁻¹ for Sb(V), 1.3 ng g⁻¹ for Se(IV), 1.0 ng g⁻¹ for Se(VI), 1.1 ng g⁻¹ for Te(IV), 0.5 ng g⁻¹ for Te(VI), and 0.9 ng g⁻¹ for Bi(III), in all cases expressed in terms of sample dry weight.     

Anion-exchange behavior of rare earths,thorium, protactinium and uranium in thiocyanate-chloride media

The anion exchange of rare earths(III), thorium(IV), protactinium(V) and uranium (VI) from thiocyanate-chloride media was investigated. The equilibrium, distribution study showed that the rare earths(III) and yttrium(III) were not significantly adsorbed on a basic anion-exchangc resin, while thorium(IV), protactinium(V) and uranium(VI) were strongly adsorbed. Adsorption from the thiocyanate-chloride solutions is in the order, U(Vl) > Pa(V) > Th(IV). The separation of rare earths(III) or yttrium(III), thorium(IV), protactinium(V) and uranium(VI) was successfully accomplished by column elution in thiocyanate-chloride media. A rapid and effective ion-exchange method for separating protactinium-233 from irradiated thorium(IV) is also presented.     

Selective determination of thorium in water using dual-wavelength β-correction spectrophotometry and the reagent 4-(2-pyridylazo)-resorcinol

A simple, fast, low cost, and precise direct β-correction spectrophotometric method was developed for thorium determination in water. The method is based on the reaction of Th(IV) with 4-(2-pyridylazo)-resorcinol (PAR) in aqueous solution of pH 5–6 and measuring the absorbance of the resulting red-colored complex at λ_max 497 nm. The effective molar absorptivity of the Th(IV)-PAR complex was 2.52 × 10⁴ L mol⁻¹ cm⁻¹. Beer’s law and Ringbom plots were obeyed in the concentration range 0.04–2.0 and 0.07–1.2 μg mL⁻¹ of thorium ions using β-correction spectrophotometry, respectively. The limits of detection and quantification of Th(IV) were 0.02 and 0.066 μg mL⁻¹, respectively. The developed method was applied for the analysis of thorium in certified reference material (IAEA-soil-7), tap-, underground- and Red-sea water samples. The validation of the method was also tested by comparison with data obtained by ICP-MS. The method is convenient, less sensitive to common interfering species and less laborious than most of published methods. The statistical treatment of data in terms of Student t-tests and variance ratio f-tests has revealed no significance differences. The structure of the Th(IV)-PAR complex was determined with the aid of spectroscopic measurements (UV–Visible and Fourier Transform Infrared Spectroscopy).     

Rapid and interference free determination of ultra trace level of uranium in potable water originating from different geochemical environments by ICP-OES

Direct determination of uranium in the concentration range of 8 μg L⁻¹ to mg L⁻¹ in water samples originating from different geochemical environments has been done using Inductively Coupled Plasma-Optical Emission Spectroscopy (ICP-OES). Uranium detection with 2–3% RSD (relative standard deviation) has been achieved in water samples by optimizing the plasma power, argon and sheath gas flow. These parameters were optimized for three different emission lines of uranium at 385.958, 409.014 and 424.167 nm. Interference arising due to the variation in concentration of bicarbonate, sodium chloride, calcium chloride, Fe and dissolved organic carbon (DOC) on the determination of uranium in water samples was also cheeked as these are the elements which vary as per the prevailing geochemical environment in groundwater samples. The concentration of NaHCO₃, CaCl₂ and NaCl in water was varied in the range 0.5–2.0%; whereas Fe ranged between 1 and 10 μg mL⁻¹ and DOC between 0.1–1%. No marked interference in quantitative determination of uranium was observed due to elevated level of NaHCO₃, CaCl₂ and NaCl and Fe and DOC in groundwater samples. Concentration of uranium was also determined by other techniques like adsorptive striping voltametry (AdSv); laser fluorimetry and alpha spectrometry. Results indicate distinct advantage for uranium determination by ICP-OES compare to other techniques.