Preparation and conductivities of polyacrylic acid/polyvinylimidazole grafted and ungrafted iron oxide nanocomposite polymer electrolytes

Nanocomposites of Polyacrylic acid/polyvinylimidazole (PAA/PVI) with grafted and ungrafted iron oxide nanoparticles were prepared by a Reflux method. The Fe₃O₄ nanoparticles with 10 nm average diameter were synthesized by controlled co-precipitation and silanization of Si-PVI on Fe₃O₄ was used to obtain the grafted ones. Grafting becomes important at composites of less PVI that cause drastic decreases in AC conductivity. The content of PVI has important effects on the conductivity mechanism of these composites. The effect of grafting and Polyacrylic acid/polyvinylimidazole molar ratio on the conduction mechanism were studied. The conduction mechanism of iron oxide nanocomposites can be adjusted by changing molar ratio of Polyacrylic acid/polyvinylimidazole and grafting of Fe₃O₄ NPs.      

Fe3O4/WO3 hierarchical core-shell structure: high-performance and recyclable visible-light photocatalysis

A facile solvothermal epitaxial growth combined with a mild oxidation route has been developed for the fabrication of a magnetically recyclable Fe(3)O(4)/WO(3) core-shell visible-light photocatalyst. In this core-shell structured photocatalyst, visible-light-active WO(3) nanoplates (the shells) with high surface area are used as a medium to harvest absorbed photons and convert them to photogenerated charges, while conductive Fe(3)O(4) microspheres (the cores) are used as charge collectors to transport the photogenerated charges. This is a new role for magnetite. The Fe(3)O(4)/WO(3) core-shell structured photocatalysts possess large surface-exposure area, high visible-light-absorption efficiency, stable recyclability, and efficient charge-separation properties, the combination of which has rarely been reported in other visible-light-active photocatalysts. Photoelectrochemical investigations verify that the core-shell structured Fe(3)O(4)/WO(3) has a more effective photoconversion capability than pure WO(3) or Fe(3)O(4). At the same time, the visible-light photocatalytic ability of the Fe(3)O(4)/WO(3) photocatalyst has significantly enhanced activity in the photodegradation of organic-dye materials. The results presented herein provide new insights into core-shell materials as high-performance visible-light photocatalysts and their potential use in environmental protection.     

Tb(III)与PNIPAM接枝核壳纳米微球相互作用的研究

利用透射电镜、X射线光电子能谱、动态激光光散射和荧光光谱技术对Tb(III)与聚N-异丙基丙烯酰胺(PNIPAM)接枝核壳纳米微球PNIPAM-g-P(NIPAM-co-St) (PNNS)的相互作用进行了研究. 结果表明: Tb(III)和热敏性的核壳纳米微球PNNS有显著的相互作用. 其一, Tb(III)可与PNNS中酰胺基团上的氧原子配位形成微球配合物Tb(III)-PNNS; 其二, Tb(III)-PNNS微球配合物兼具热敏性; 其三, 该配合物在545 nm处的荧光强度较Tb(III)增大了233倍, Tb(III)与PNNS分子间能量传递达到50%, 当Tb(III) 质量分数为12%时荧光强度最大.     

SYNTHESIS OF POLY(DIVINYLBENZENE-co-ACRYLIC ACID) HOLLOW MICROSPHERES WITH GOLD NANOPARTICLES ON THE INTERIOR SURFACE

Poly(divinylbenzene-co-acrylic acid) (poly(DVB-co-AA)) hollow microspheres with gold nanoparticles on the interior surfaces were prepared from the gold nanoparticles-coated poly(methacrylic acid) (PMAA@Au@poly(DVB-co-AA)) core-shell microspheres by removal of the PMAA core in water.Au nanoparticles-coated PMAA microspheres were afforded by the in-situ reduction of gold trichloride with PMAA microsphere as stabilizer via the interaction between carboxylic acid groups and Au nanoparticles.Gold nanoparticle...     

Ag/WO3纳米复合膜的制备及其电致变色性质和器件的研究

通过真空镀膜方法制备的纳米Ag薄膜均匀致密, 表面光滑. 然后通过电化学方法在Ag纳米薄膜上沉积一层三氧化钨(WO3), 制备纳米Ag/WO3复合膜. 并在此基础上构筑五层式玻璃/ITO/纳米Ag-WO3复合膜/固态电解质/聚(3-甲基噻吩)/ITO/玻璃电致变色器件. 实验结果表明, 与传统的WO3膜相比, 纳米Ag/WO3复合膜具有更好的电化学活性、更高的对比度、更短的响应时间, 以及更好的稳定性. 由该复合膜组装的电致变色器件工艺简单, 电致变色性能良好.     

聚苯乙烯/Ag核壳结构纳米微粒的制备及表征

用种子乳液聚合法合成了聚苯乙烯（PS）/Ag复合纳米粒子,进一步利用分步聚合技术实现了聚甲基丙烯酸甲酯(PMMA)在微球表面功能化,分别用TEM、XRD、TG-DTA及FT-IR对其结构和形貌进行了表征,并考察了其摩擦学性能.结果表明,在所选择的实验条件下,合成了以Ag纳米微粒为核,PS、PMMA为壳层的核壳结构复合纳米微球,其中Ag纳米核平均粒径约12 nm,复合微球粒径约25 nm,颗粒较均匀并且在有机溶剂中有良好的分散性,作为润滑油添加剂,具有良好的抗磨性能.     

Ag负载TiO2核壳基底的制备及对结晶紫的高效(SERS)检测

通过简单的一步水热法制备了TiO2核壳微球,然后经过原位光还原将Ag负载于其表面,成功得到了用于有机分子检测的Ag负载TiO2核壳表面增强拉曼散射（SERS）基底。得益于TiO2核壳微球的结构,其对结晶紫（CV）分子表现出高的吸附容量。单一TiO2核壳微球对CV的检测限为10-3 M,而负载Ag以后,其对CV的检测限能达到10-7 M,增强因子（EF）可达3.49×105。优异的SERS检测性能可能归因于以下几点：（1）半导体TiO2为Ag纳米粒子提供了均匀分散的骨架,创造了高密度的热点;（2）为CV分子提供了大的吸附面积;（3）复合材料促进了激发光子的相互作用。     

还原态WO_3/Al_2O_3,NiO/Al_2O_3和NiO-WO_3/Al_2O_3催化剂上H_2,CO,O_2的吸附特性

在加氢精制和许多其它催化过程中,Mo,W是主要的活性组分,Co,Ni通常作为助剂,有关Co-Mo体系的研究文献报导很多~[1.2], 但由于钨较难还原和硫化,关于     

Crystallographically oriented mesoporous WO3 films: synthesis, characterization, and applications.

Mesoporous semiconducting films consisting of preferentially orientated monoclinic-phase nanocrystals of tungsten trioxide have been prepared using a novel version of the sol-gel method. Transformations undergone by a colloidal solution of tungstic acid, stabilized by an organic additive such as poly(ethylene glycol) (PEG) 300, as a function of the annealing temperature have been followed by means of a confocal Raman microscope. The shape and size of WO3 nanoparticles, the porosity, and the properties of the films depend critically on preparation parameters, such as the tungstic acid/PEG ratio, the PEG chain length, and the annealing conditions. Well-crystallized WO3 films combine excellent photoresponse to the blue region of the solar spectrum, up to 500 nm, with good transparency at wavelengths larger than 550 nm. Particular applications of these nanocrystalline WO3 films include photoelectrochemical and electrochromic devices.     

(Phen)2.5HPW/WO3复合空心微球的制备及光催化性能

通过磷钨酸H3PW12O40(HPW)和邻菲啰啉C12H8N2(Phen)的溶液反应,合成了杂多化合物(C12H8N2)2.5H3PW12O40((Phen)2.5HPW),以WO3空心微球为载体,负载杂多化合物(Phen)2.5HPW,制备了(Phen)2.5HPW/WO3复合空心微球.用等离子体原子发射光谱(ICP...     

亲/疏水不对称空心聚合物微球制备及磁性粒子装载研究

首先将(马来酸酐-醋酸乙烯酯共聚物)核/(马来酸酐-二乙烯基苯共聚物)壳微球的壳层外表面酐基烷基溴化,然后将核溶蚀、壳层内表面酐基水解,制得内表面含亲水羧基、外表面含烷基溴、具有微孔(Barrett-Joyner-Halenda平均孔径14.9nm)的空心聚合物微球.以此空心微球为微反应器,使Fe2+和Fe3+通过球壁...     

Facile synthesis of Montroseite VOOH, Paramontroseite VO2 and V2O3-VO2 carbonaceous core-shell microspheres

Hydrothermal carbonization of sucrose was used to controllably synthesize Montroseite VOOH and Paramontroseite VO₂ nanoparticles carbonaceous core-shell microspheres. After calcinations, V₂O₃-VO₂-C core-shell microspheres were obtained. When they were used as cathode materials in lithium-ion battery (LIB), it was found that Montroseite VOOH carbonaceous core-shell microspheres exhibited higher discharge capacity than Paramontroseite VO₂ counterpart, while the content of V₂O₃ had some large effects on the electrochemical properties of V₂O₃-VO₂C core-shell microspheres.     

异质结构AgCl/Bi2WO6微米球制备、表征及其光催化性能

首先利用水热法制备了由纳米片组装的粒径为1.5–2μm的Bi2WO6微球,然后在微球表面沉积了不同含量的AgCl (5 wt%,10wt%,20wt%,30wt%),制备了异质结构AgCl/Bi2WO6微球光催化剂.利用X射线粉末衍射、扫描电镜、透射电镜、红外光谱、紫外-可见漫反射吸收等手段对所制的光催化剂进行表征,并以紫外光和可见光分别为光源,罗丹明B为降解对象测试了其光催化活性,考察复合不同含量的AgCl对Bi2WO6光催化剂的性能影响.结果表明,沉积AgCl对Bi2WO6的晶体结构、表面性能和光吸收性能没有产生明显影响,但大幅度提高了Bi2WO6的紫外和可见光催化活性.当复合20wt%AgCl时, AgCl/Bi2WO6光催化活性最佳,紫外光下比纯Bi2WO6提高了2.2倍,可见光下提高了1倍.这主要是由于形成的AgCl/Bi2WO6异质结能有效抑制光生电子和空穴的复合,从而提了其光催化性能.     

阳极氧化膜WO3（Ⅱ）：电显色的介质效应

用循环计时电量法、循环伏安法、电化学现场(in-situ)紫外可见反射光谱技术和光电流谱技术研究了溶剂和阳离子(H~+,Li~+)对阳极氧化膜WO_3电显色稳定性和过程的影响。从循环计时电量图可以测定表征膜稳定性的氢或锂的累积量和暂态周期数。实验发现W/WO_3/LiCLO_4乙腈溶液体系具有高的电显色稳定性。引起WO_3膜可逆电显色的H~+和Li~+离子的嵌-脱过程的界面电化学机理不同。着色态WO_3膜的色心是自由电子,其密度超过10~(21)/cm~3,生色机理是等离子体振荡。     

水热法制备多层核壳结构Gd_2O_3:Eu~(3+)空心微球

以稀土硝酸盐-葡萄糖的混合溶液作为前驱体,采用一步水热法和随后的热处理得到了多层核壳结构Gd_2O_3:Eu~(3+)空心微球,并用X-射线衍射(XRD)、场发射扫描电镜(FESEM)、透射电镜(TEM)、X-射线能量色散光谱(EDS)和荧光光谱等测试手段对所得样品进行了表征.结果表明:所得空心球样品为纯的立方相的Gd_2O_3.具有规则的多层核壳空心结构,空心球的直径在2～3μm左右,壁厚约为100 nml,并且Gd_2O_3:Eu~(3+)空心球是由尺寸约为30 nm的球形纳米颗粒白组装而成.样品中含有Gd、Eu、O元素.该空心球样品具有强的Eu~(3+)的特征红光发射以及长的荧光寿命,可以用来作为时间分辨荧光标记物.     

From hollow olive-shaped BiVO4 to n-p core-shell BiVO4@Bi2O3 microspheres: controlled synthesis and enhanced visible-light-responsive photocatalytic properties

In this study, hollow olive-shaped BiVO(4) and n-p core-shell BiVO(4)@Bi(2)O(3) microspheres were synthesized by a novel sodium bis(2-ethylhexyl)sulfosuccinate (AOT)-assisted mixed solvothermal route and a thermal solution of NaOH etching process under hydrothermal conditions for the first time, respectively. The as-obtained products were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy, Brunauer-Emmett-Teller surface area, and UV-vis diffuse-reflectance spectroscopy in detail. The influence of AOT and solvent ratios on the final products was studied. On the basis of SEM observations and XRD analyses of the samples synthesized at different reaction stages, the formation mechanism of hollow olive-shaped BiVO(4) microspheres was proposed. The photocatalytic activities of hollow olive-shaped BiVO(4) and core-shell BiVO(4)@Bi(2)O(3) microspheres were evaluated on the degradation of rhodamine B under visible-light irradiation (λ > 400 nm). The results indicated that core-shell BiVO(4)@Bi(2)O(3) exhibited much higher photocatalytic activities than pure olive-shaped BiVO(4). The mechanism of enhanced photocatalytic activity of core-shell BiVO(4)@Bi(2)O(3) microspheres was discussed on the basis of the calculated energy band positions as well. The present study provides a new strategy to enhancing the photocatalytic activity of visible-light-responsive Bi-based photocatalysts by p-n heterojunction.     

复合Fe2O3纳米粒子的高分子微球的结构表征

近年来，复合有机、无机粒子的高分子微球及其特殊性质越来越引起人们的兴趣与关注［1］．获得有机、无机复合微球的方法很多，如在无机粒子存在下的乳液或无皂乳液聚会[2，3]，通过可聚合的表面活性剂在粒子表面形成胶囊化层[4]以及共沉淀法等[5]．这些无机粒子包括氧化钛、氧化铁、氧化铝及氧化硅等．Haga等[6]增发现包覆在聚合物粒子中的CdS与其本体的光电性质不同；单分散的聚合物微球可以在基片上被组装成二维乃至三维有序的结构[7]．这为信息存储、立体印刷等领域提供了新途径．因此，将无机粒子与聚合物复合成为功能化粒子是一项有…     

以聚乙烯基咪唑为配基的内毒素亲和吸附剂的研究

通过乙烯基咪唑(VI)在硅胶粒子表面的自由基接枝聚合制备了一种以聚乙烯基咪唑为配基的新型内毒素亲和吸附剂. 用FTIR检测样品中咪唑基的特征吸收, 用热重分析法(TGA)测定了PVI的接枝率. 实验发现, PVI在吸附剂中的含量对内毒素的吸附率影响很大. 当PVI的接枝率为2.5％左右时, 吸附剂对内毒素的去除率最大. 在离子强度小于1 mol/L和pH=7的中性条件下, PVI吸附剂对内毒素具有最佳的吸附性能. 该吸附剂具有良好的血液相容性. 内毒素在该亲和吸附剂上的吸附等温线符合Freundlich吸附方程, 其吸附动力学为二级反应.     

Photocatalysis and photoinduced hydrophilicity of WO3 thin films with underlying Pt nanoparticles

The photocatalytic oxidation and photoinduced hydrophilicity of thin tungsten trioxide (WO(3)) films coupled with platinum (Pt) nanoparticles were investigated. WO(3) films with underlying Pt nanoparticles (WO(3)/Pt/substrate) and those with overlying Pt nanoparticles (Pt/WO(3)/substrate) were synthesized by sputtering and sol-gel methods. Between these films, underlying Pt nanoparticles greatly enhanced the photocatalytic oxidation activity of WO(3) without decreasing the photoinduced hydrophilic conversion. However, overlying Pt nanoparticles deteriorated the hydrophilicity of WO(3) because the Pt nanoparticle surface was hydrophobic. The enhanced photocatalytic reaction by the Pt nanoparticles was attributed to the multi-electron reduction in Pt, which is caused by the injected electrons from the conduction band of WO(3). The relationship between photocatalytic activity and thin film structure, including the size of Pt nanoparticles, the thickness and porosity of the WO(3) layer, were investigated. Consequently, the optimum structure for high performance in both photocatalysis and photoinduced hydrophilicity was WO(3) (50 nm)/Pt(1.5 nm)/substrate, and this film exhibited a significant self-cleaning property even under visible light irradiation.     

Silica-dendrimer core-shell microspheres with encapsulated ultrasmall palladium nanoparticles: efficient and easily recyclable heterogeneous nanocatalysts

We report the synthesis, characterization, and catalytic properties of novel monodisperse SiO(2)@Pd-PAMAM core-shell microspheres containing SiO(2) microsphere cores and PAMAM dendrimer-encapsulated Pd nanoparticle (Pd-PAMAM) shells. First, SiO(2) microspheres, which were prepared by the St?ber method, were functionalized with vinyl groups by grafting their surfaces with vinyltriethoxysilane (VTS). The vinyl groups were then converted into epoxides by using m-chloroperoxybenzoic acid. Upon treatment with amine-terminated G4 poly(amidoamine) (PAMAM) dendrimers, the SiO(2)-supported epoxides underwent ring-opening and gave SiO(2)@PAMAM core-shell microspheres. Pd nanoparticles within the cores of the SiO(2)-supported PAMAM dendrimers were synthesized by letting Pd(II) ions complex with the amine groups in the cores of the dendrimers and then reducing them into Pd(0) with NaBH(4). This produced the SiO(2)@Pd-PAMAM core-shell microspheres. The presence of the different functional groups on the materials was monitored by following the changes in FTIR spectra, elemental analyses, and weight losses on thermogravimetric traces. Transmission electron microscopy (TEM) images showed the presence of Pd nanoparticles with average size of 1.56 ± 0.67 nm on the surface of the monodisperse SiO(2)@Pd-PAMAM core-shell microspheres. The SiO(2)@Pd-PAMAM core-shell microspheres were successfully used as an easily recyclable catalyst for hydrogenation of various olefins, alkynes, keto, and nitro groups, giving ~100% conversion and high turnover numbers (TONs) under 10 bar H(2) pressure, at room temperature and in times ranging from 10 min to 3 h. In addition, the SiO(2)@Pd-PAMAM core-shell microspheres were proven to be recyclable catalysts up to five times with barely any leaching of palladium into the reaction mixture.