High-pressure microwave dissolution of ceramics prior to trace metal determinations by microwave induced plasma atomic emission spectrometry

A commercial laboratory microwave acid digestion system was evaluated for the acid dissolution of ceramic powders (Al₂O₃, AlN, BN and Si₃N₄) prior to the determination of their trace element content by microwave induced plasma atomic emission spectrometry. Newly designed vessels, capable of withstanding internal pressures of over 110 bar, provide rapid and satisfactory results for sample dissolution. Sample preparation time was approximately 30 min (including the subsequent cooling time and preparation of the final solution). Results from conventional stainless-steel acid digestion vessel (Teflon bomb) dissolution are compared with the microwave bomb results of microwave plasma atomic emission spectrometry.     

超级微波消解-电感耦合等离子体发射光谱（ICP-OES）法测定土壤中18种元素

为提高土壤多元素同时检测的效率,采用超级微波消解-电感耦合等离子体发射光谱法测定土壤中钾、钠、钙、镁、铜、铁、锰、锌、磷、硫、硼、砷、镉、铬、铅、钴、镓、锂等18种元素含量。比较了超级微波消解、常规微波消解和电热板消解的处理效果,采用超级微波消解法对样品进行前处理,并优化了消解条件。在最优条件下,各元素的检出限在0.05~20 mg/kg,加标回收率在86.2%~107.5%,RSD在0.1%~3.0%,方法准确度及精密度可以满足多元素同时测定的需求,且该方法具有简单、快速、成本低、用酸量少、重现性好等特点。     

Multielement determination of major elements in polymer additives by microwave induced plasma atomic emission spectrometry after microwave digestion

A method for multielement determination of major elements in polymer additives by microwave induced plasma atomic emission spectrometry (MIP-AES) has been elaborated. Microwave digestion with nitric acid was selected for sample preparation because of its speed and versatility. Sodium nitrate was added to the digestion mixture in order to reduce phosphorus losses. The precision obtained varied between 2 and 4.5% depending on the element determined. The accuracy of the method was studied by analyzing the Spex 5-element oil standard. The method was applied to a variety of commercial and in-house prepared compositions.     

等离子体发射光谱法测定矿山水样中硫酸盐的研究

水质中硫酸盐的测定方法很多,但对于成分复杂且盐分很高的矿山水样,传统方法操作繁琐且不环保,本文建立了等离子体发射光谱法测定矿山水样中硫酸盐的方法,样品采用硝酸和盐酸进行加热消解后既可去除硫化物,降低水质的黏度,又可实现多元素同时测定。该方法检出限为0.03mg/L,相对标准偏差为0.1～0.4%(n=6),方法具有方便,快捷,检出限低,精密度、准确度高且线性范围广的优点。     

Simultaneous determination of hydride forming elements (As, Sb, Se, Sn) and Hg in sonicate slurries of biological and environmental reference materials by hydride generation microwave induced plasma optical emission spectrometry (SS-HG-MIP-OES)

A slurry sampling hydride generation (SS-HG) method for the simultaneous determination of hydride forming elements (As, Sb, Se, Sn) and Hg, without total sample digestion, has been developed using batch mode generation system coupled with microwave induced plasma optical emission spectrometry (MIP-OES) from certified biological and environmental reference materials. Slurry concentration up to 3.6% m/v (particles < 80 μm) prepared in 10% HCl containing 100 μl of decanol, by the application of ultrasonic agitation, was used with calibration by the standard addition technique. Harsh conditions were used in the slurry preparation in order to reduce the hydride forming elements to their lower oxidation states, As(III), Sb(III), Se(IV) and Sn(II) and Hg, being reduced to mercury vapor, before reacting with sodium tetrahydroborate. An ultrasonic probe was used to homogenize the slurry in the quartz cup just before its introduction into the reaction vessel. For 10 ml of slurry sample, detection limits (LOD, 3σ_blank, peak area) of 0.06, 0.08, 0.15, 0.12 and 0.10 μg g^− 1 were obtained for As, Sb, Se, Sn and Hg, respectively. The method offers relatively good precision (RSD ranged from 9 to 12%) for slurry analysis. To test the accuracy, three certified reference materials were analyzed with the analyte concentrations mostly in the μg g^− 1 level. Measured concentrations are in satisfactory agreement with certified values for the biological reference materials: NRCC LUTS-1 (lobster hepatopancreas), NRCC DOLT-2 (Dogfish Liver) and environmental reference material: NRCC PACS-1 (Marine Sediment), all adequate for slurry sampling. The method requires small amounts of reagents and reduces contamination and losses.     

微波消解-电感耦合等离子体发射光谱法测定土壤中的硫

利用微波消解仪消解土壤样品,采用电感藕合等离子体发射光谱仪测定土壤中硫的含量。以浓王水为消解试剂,对土壤样品进行微波消解,优化了王水用量,考察了微波消解条件、谱线干扰情况和仪器参数对硫灵敏度的影响。硫的质量浓度在0~40 mg/L范围内与光谱强度具有良好的线性关系,线性相关系数为0.9997,硫的检出限为0.053 mg/L。土壤中硫测定结果的相对标准偏差为1.54%~7.84%(n=7)。对六种土壤国家一级标准物质进行了测定,测定结果与推荐值相符,无显著性差异。该方法简便、准确,分析效率高,能够满足日常批量样品分析的要求。     

Determination of precious metals in geological samples by continuous powder introduction microwave induced plasma atomic emission spectrometry after preconcentration on activated carbon

A novel method was developed for analysing geological materials for Au, Ag, Pd and Pt by continuous powder introduction microwave induced plasma atomic emission spectrometry (CPI-MIP-AES). The preconcentration of the trace metals on activated carbon (AC) was performed before conducting MIP-AES measurements in order to obtain accurate and precise analytical results. The method proposed is based on the selective sorption of precious metals that are subsequently introduced to the plasma as a dry particulate aerosol consisted of analytes collected on the sorbent. The technical design and operating conditions of the novel sample introduction system based on the fluidized-bed concept has been optimized. The microwave excitation source with integrated rectangular cavity TE₁₀₁ and vertically positioned plasma torch has been used. The signal stability proved to be adequate for sequential mode of measurements due to the vertical plasma configuration as well as the MIP-AES system compatibility with the CPI technique. Calibration was done using home-made standards obtained by sorption of metals of interest from standard solutions on activated carbon. Precision is typically 1-4% relative standard deviation at the 1 μg g⁻¹ level. Under measurement conditions the detection limits for Ag, Au, Pd and Pt were 24, 43, 57 and 550 ng per 1 g of AC, respectively. The proposed procedure was used for Au, Ag, Pd and Pt determination in the platinum ore SARM-7 as well as Au and Ag in the Chinese soil GBW-07405 certified reference materials. The standard addition technique was used and recoveries revealed that the proposed method shows good accuracy and precision.     

The use of optical emission spectrometry with microwave induced plasma (MIP) discharges in a surfatron combined to different types of hydride generation for the determination of arsenic

The stability and analytical figures of merit of argon microwave induced plasma (MIP) discharges in a surfatron as sources for optical emission spectrometry (OES) are described. These MIPs have been used for the determination of arsenic after hydride generation. They could cope with the excess of hydrogen developed during the hydride generation step and thus not necessitated an isolation of the hydrides before releasing them into the MIP. Two methods for the generation of the volatile AsH₃ were applied. First a micro method was used with solid NaBH₄ on which 10 1 of the acidified sample solution is transferred. Its capabilities were compared to those of continuous hydride generation using a 5% (w/w) NaBH₄-solution and continuous liquid removal in a flow cell. Both methods were optimized for an argon MIP operated at a power of 120–160 W and gas flows of 20 l/h Ar. In the case of solid NaBH₄ the detection limit for As has been found to be 1.0 g/ml (10 ng) and with the flow cell hydride generation 50 ng/ml. The calibration curves are linear over three orders of magnitude. Interferences caused by Sb, Fe, Sn and NaCl were investigated. No interferences occurred for Sb up to an interferent concentration of 250 g/ml. The presence of Fe causes a significant depression of the As signal whereas an increase of the As signal was observed in the case of Sn. High NaCl concentrations did not influence the As signals when using continuous hydride generation, but had a great influence when using solid NaBH₄.     

Determination of major and trace elements in biological materials by microwave induced plasma optical emission spectrometry (MIP-OES) following tetramethylammonium hydroxide (TMAH) solubilization

A simple, alternative method to acid digestion is presented for the preparation of biological materials for major and trace elements by microwave induced plasma optical emission spectrometry (MIP-OES). Standard reference materials were solubilized using a methanolic solution of tetramethylammonium hydroxide (TMAH) by the application of ultrasonic agitation. Following dilution with water suspensions were pumped to a V-groove Babington-type nebulizer then into argon plasma. Limits of detection and precision are reported for major (Na, K, Ca, Mg) and trace (Cu, Fe, Sr, Zn) elements. Standard addition procedures were used to minimize possible matrix interferences. The method offers relatively good precision (R.S.D. ranged from 6 to 12%). Measured concentrations are in satisfactory agreement with certified values for the biological reference materials: TORT-1 (Lobster hepatopancreas), IAEA-153 (Milk powder) and NIST 1577 (Bovine liver). The simple procedure could be useful as a routine analysis of biological materials.     

微波消解-电感耦合等离子体发射光谱法测定植物样品中的磷、硫

本方法采用微波消解处理样品,电感耦合等离子体发射光谱法测定植物样品中的磷、硫的含量,选用优化微波消解条件进行消解,磷和硫方法最低检出限分别为0.925mg/kg、1.82 mg/kg。精密度RSD和相对误差RE均小于3%,对新鲜植物样品进行加标回收试验,加标回收率为90.5%~107%,证明本方法既可用于检测干植物样品,又可检测新鲜植物样品。     

Ligandless-ultrasound-assisted emulsification microextraction followed by inductively coupled plasma-optical emission spectrometry for simultaneous determination of heavy metals in water samples

In this study, a simple and efficient method of ligandless-ultrasound-assisted emulsification microextraction (LL-USAEME) followed by inductively coupled plasma-optical emission spectrometry (ICP-OES) has been developed for simultaneous extraction, preconcentration and determination of manganese, cadmium, cobalt and nickel in water samples. In the proposed approach, tetrachloroethylene was selected as extraction solvent. The effect of important experimental factors such as volume of extraction solvent, pH, sonication time, salt concentration, and temperature was investigated by using a fractional factorial design (2^5?1) to identify important factors and their interactions. In the next step, a Box-Behnken design (BBD) was applied for optimisation of significant factors. The obtained optimal conditions were: 30?µL for extraction solvent, 12 for pH, 5?min for sonication time, and 5% w/v for salt concentration. The limits of detections (LODs) for Cd(II), Co(II), Mn(II) and Ni(II) were 0.20, 0.13, 0.21 and 0.28?µg?L^?1, respectively. Relative standard deviations (RSD, C?=?200.0?µg?L^?1, n?=?9) were between 3.4–7.5% and the calibration graphs were linear in the range of 0.25 to 1000.0?µg?L^?1 for Mn, 0.5–1000.0?µg?L^?1 for Co and Ni and 1.0–250.0?µg?L^?1 for Cd. The determination coefficients (R ²) of the calibration curves for the analytes were in the range of 0.993 to 0.999. The proposed method was validated by using two certified reference materials, and also the method was applied successfully for the determination of heavy metals in different real water samples.     

Multi-element determination in raft mussels by fast microwave-assisted acid leaching and inductively coupled plasma-optical emission spectrometry

Studies on the application of a short microwave irradiation cycle and the use of diluted acids to extract trace elements from raft mussel samples were developed. Multi-element determinations (Al, Ba, Cd, Cr, Cu, Fe, Mn, Pb, Sn, V and Zn) were carried out by inductively coupled plasma-optical emission spectrometry (ICP-OES). Parameters such as acid/oxidizing reagents (diluted nitric acid, hydrochloric acid and hydrogen peroxide) concentrations, acid/oxidizing solution volume, temperature, ramp time and hold time for the microwave heating were simultaneously studied by using an experimental design approach. The optimum conditions have showed the sample pre-treatment of 10 mussel samples to less than 3.0 min when a microwave power of 600 W and a controlled temperature of 65 °C were used. This time (hold time plus ramp time) is quite shorter than those reported for conventional microwave-assisted acid digestion procedures. Since temperature inside the reactor is not high, the venting time can be shorted to 15 min. In addition, the concentration of acid/oxidizing reagents needed to complete the acid leaching (2.5 M, 3.0 M and 0.5 % (m/v) for nitric acid, hydrochloric acid and hydrogen peroxide, respectively) is lower than the required concentration for a conventional microwave-assisted acid digestion (concentrated acids). The proposed method has showed a good repeatability of the overall method, and relative standard deviations between 11 and 2% were reached for 12 replicate microwave-assisted acid leaching and ICP-OES measurements. The method was finally validated by analyzing TORT-1 and GBW-08571 certified reference materials and it was successfully applied to fast multi-element determinations in several raft mussel samples.     

Membrane desolvation for the analysis of organic solutions and liquid chromatographic samples with low power helium microwave induced plasma atomic emission detection

A flat sheet membrane desolvator (FSMD) was used to extend the applicability of a 120 W helium microwave induced plasma (He-MIP) to elemental analysis of organic-solvent-based samples and element selective liquid chromatographic detection. With the FSMD on-line, methanol could be nebulized with a sample flow rate of 1.5 ml/min and a carrier gas flow rate of 1.2 l/min without extinguishing the plasma. Under these conditions, applying desolvator countercurrent gas flows in the range 0–8 l/min restored of the original pink color of the pure helium MIP from the bluish-green caused by methanol. Significant reductions in the emission intensities of C₂ species at 436.5, 473.7, 512.9, and 563.6 nm were observed with the application of the FSMD. The intensities of chlorine analyte emission lines at 479.5, 481.0 and 481.9 nm increased with increasing countercurrent gas flow rates and reached a maximum intensity with a flow rate of 5.0 l/min. Detection limits for Cl and Pb were 2.1 and 0.1 ppm using a 1 m focal length monochromator. Other elements and solvent combinations were also examined. Element selective liquid chromatographic detection was preliminarily examined by monitoring 2,6-dichlorobenzene and 5,7-dichlorohydroxyquinoline at the 479.5 nm Cl atomic emission line. Chlorine detection limits in the 3–7 μg range (70–190 ng/s) were obtained.     

超级微波消解-电感耦合等离子体发射光谱(ICP-OES)法测定乌兰茶晶石中15种稀土元素含量

乌兰茶晶石属于富含稀土型矿物,能准确监测乌兰茶晶石中的稀土元素具有非常重要的意义。本文通过15组微波消解试剂条件实验及对超级微波消解仪工作参数的优化,最终确定采用硝酸-氟硼酸-磷酸体系在超级微波消解仪中260℃下加热30分钟进行样品消解,赶酸后用2%硝酸复溶, 建立了超级微波消解-电感耦合等离子体发射光谱法（ICP-OES）测定乌兰茶晶石中15种稀土元素的方法,整个过程高效、操作简便、无损失、无污染。利用ICP-OES进行测定,所选谱线无干扰、信背比高,校准曲线线性相关系数大于0.99995,测试结果准确,精密度＜4.0%,加标回收率在91.3%-96.3%之间。该方法用于花岗岩（GBW07103）测试,测定值与标准值一致。结果表明,硝酸-氟硼酸-磷酸消解法磷酸法可替代碱溶法对乌兰茶晶石实际样品进行前处理,具有较好的稳定性和准确性,能满足实际应用需求。     

Investigation of electrochemical hydride generation coupled to microwave plasma torch optical emission spectrometry for the determination of arsenic: analytical figures of merit,interference studies and applications to environmentally relevant samples

A continuous flow thin layer electrolysis cell with a Pt cathode in combination with a microwave plasma torch operated with Ar as working gas was used for the optical emission spectrometric determination of As with the hydride technique. Under the optimised conditions the limit of detection (3σ) in the case of the As(I) 228.81 nm emission line was 81 ng mL^?1. Especially the influence of the transition metals Cu(II), Fe(III) and Ni(II), of the hydride forming elements Sb(III), Se(IV) and Sn(II) and of Na on the determination of As was studied. Cu(II) was found to be the strongest interferent, as in the presence of 100 µg mL^?1 of Cu(II) the signal for 3 µg mL^?1 of As was reduced to 4% of the signal without interferent. Sn(II) and Sb(III) were found to yield an increase of the signal for As. L-cysteine and KI/ascorbic acid (1 : 1) at a concentration of 2% were found effective to reduce the interferences of Cu(II), Fe(III) and Ni(II). For a solution containing 3 µg mL^?1 of As and 100 µg mL^?1 of Ni(II) it was shown that in the presence of L-cysteine or KI/ascorbic acid the signal for As was 99% and 94% of the one without interferent, whereas it was only 43% without masking reagents. The procedure could be used for the determination of As in a digested coal fly ash standard reference material (NIST SRM 1633a®) with a certified value of 145 ± 15 µg g^?1 for As. A concentration of 131 ± 15 µg g^?1 was found. Additionally, As could be determined in two process water samples from a copper refinery. It was found that the amount of As determined with ECHG-MPT-OES agrees well with the values determined by FAAS and ICP-OES at the 0.02 and 1.6 g L^?1 level, respectively.     

Preliminary investigation of a tangential flow torch with coupling probe injector for helium microwave induced plasma mass spectrometry

A stable, low gas-flow torch has been developed for use with a helium microwave induced plasma (MIP). A toroidal plasma with central analyte introduction is obtained by the addition of a tantalum coupling probe injector tube. This injector penetrates through 100% of the total cavity depth and aids in the efficiency of power transfer to the cavity, in plasma initiation, and in circumventing the effects of a lack of homogeneity in the microwave field on analyte distribution in the plasma. The tangential helium flow was 41/min and the microwave power was 60 W.Presented in part at the 1989 European Winter Conference on Plasma Spectrochemistry, Reutte, Austria     

Determination of chloride ion in aqueous samples by isotope-dilution Fourier-transform flame infrared emission (ID-FIRE) spectrometry

An isotope dilution method for the determination of chloride ion in aqueous samples is described. The method makes use of the isotopic shift in the rotational lines of the 1–0 band of HCl emitted in the near infrared region of the spectrum by vibrationally excited HCl molecules present in a hydrogen/entrained air flame. Chloride ion in the sample is converted to chlorine gas by electrolysis and swept into a hydrogen/entrained air flame where it is converted into HCl. Because isotope dilution is an absolute method of analysis, matrix effects are minimized, and the chlorine generation step need not be quantitative. With the system described in this paper, samples must contain at least 9 mg of chloride ion per ml, and a 2-ml sample is required. Over the range from 10 to 30 mg Cl⁻ ml⁻¹, the average error was −0.96%, and the average relative standard deviation was 3.3% for seven samples using seven of the more intense lines in the P branch. Compared with standard silver nitrate titrations, the isotope dilution procedure was not affected by such common interferences as bromide ion and iodide ion. The technique was applied to several seawater samples from different regions.     

Determination of ultra trace amounts of cobalt and nickel in water samples by inductively coupled plasma-optical emission spectrometry after preconcentration on modified C18-silica extraction disks

A highly sensitive and accurate method for preconcentration and determination of ultra trace amounts of cobalt and nickel ions in water samples is proposed. The preconcentration is achieved using C₁₈-silica extraction disks modified with 5-(6-methoxy-2-benzothiazoleazo)-8-aminoquinoline (MBTAQ). The retained ions on the prepared solid phase was eluted with 10 ml of 0.01 M nitric acid and measured by inductively coupled plasma-optical emission spectrometry (ICP-OES). The influence of the type and amount of eluent used, pH, sample and eluent flow rates, amount of MBTAQ and the effect of other ions on extraction efficiency were investigated. The limits of detection of the method were 0.08 and 0.06 μg l^− 1 for cobalt and nickel, respectively, and provide an enrichment factor of 100. The results obtained on 10 successive extractions and elution cycles revealed relative standard deviations of 1.5 and 1.0% for cobalt and nickel, respectively. The proposed method has been applied to the determination of ultra trace amounts of cobalt and nickel ions in natural and synthetic water samples with satisfactory results.     

Comparison of the cold vapor generation using NaBH4 and SnCl2 as reducing agents and atomic emission spectrometry for the determination of Hg with a microstrip microwave induced argon plasma exiting from the wafer

A 2.45 GHz low power microwave microstrip plasma (MSP) exiting the wafer and operated with Ar at atmospheric pressure was used for the optical emission spectrometric determination of Hg with the aid of a miniaturized optical fiber spectrometer with a CCD detector and the cold vapor (CV) generation technique using NaBH₄ and SnCl₂ as reductants. The experimental conditions were optimized with respect to the relative intensity of the Hg I 253.6 nm line and its signal-to-background intensity ratio (SBR). So as to understand the results of the optimization experiments, the excitation temperatures as measured from Ar I lines (T _exc) and the electron number densities (n _e) for the Ar MSP loaded with Hg vapors were determined and found to be in the range from 5500 to 6300 K and from 1.4 to 2.0 × 10¹⁴ cm⁻³, respectively. Under the optimized conditions, the detection limit for Hg of the CV-MSP-OES using SnCl₂ as the reducing agent was found to be much lower (0.11 ng mL⁻¹) than in the case where NaBH₄ was used (9 ng mL⁻¹). The linearity range was found to be up to 1 μg mL⁻¹ while the precision was of the order of 0.7–5%. The procedure with SnCl₂ as reductant was used for the determination of Hg at a concentration of 0.2 μg mL⁻¹ in synthetic water samples containing 1 to 4% (m/v) of NaCl with an accuracy of 3% as well as in a solution of the domestic sludge standard reference material (NIST SRM 2781) with a certified concentration for Hg of 3.64 ± 0.25 μg g⁻¹ for which 3.55 ± 0.41 μg g⁻¹ was found. Correspondence: J. A. C. Broekaert, Institut für Anorganische und Angewandte Chemie, Universit?t Hamburg, 20146 Hamburg, Germany     

Fractionation metallothionein-like proteins in mussels with on line metal detection by high performance liquid chromatography-inductively coupled plasma-optical emission spectrometry

A rapid method for the determination of Al, Ba, Cu, Fe, Mn, Sr and Zn binding metallothionein-like proteins (MLPs) in mussels (Mytilus galloprovincialis) by inductively coupled plasma-optical emission spectrometry was developed. The method uses a short column (8 mm × 75 mm) anion exchange high performance liquid chromatography (HPLC) with inductively coupled plasma-optical emission spectrometric (ICP-OES) detection. Working in isocratic mode (75 mM Tris-HCl at pH 7.4, flow rate at 0.8 ml min⁻¹), two major MLPs isoforms (MLP-1 and MLP-2) can be separated in ten minutes. The distribution of basal metals binding MLPs was assessed by on line HPLC and ICP-OES, while the basal contents of metals binding MLPs were obtained after off line HPLC and ICP-OES (collection of the two major fractions and multi-element determination by ICP-OES). The calculated LODs were 81, 6, 10, 13, 30, 9 and 123 ng g⁻¹ for Al, Ba, Cu, Fe, Mn, Sr and Zn binding MLP-1 and MLP-2, respectively. The repeatability of the over-all method (five different mussel cytosols prepared from the same mussel sample and subjected to the off line HPLC-ICP-OES procedure twice) was from 11.2 for Cu to 16.2% for Zn. The method was finally applied to different raft mussels from Ría de Arousa estuary in order to know basal levels of elements binding MLPs.