聚丙烯孔洞铁电驻极体膜的电极化及其电荷动态特性

根据栅控恒压电晕充电组合反极性电晕补偿充电法的实验结果计算出铁电驻极体的极化强度.结果说明，伴随着薄膜内孔洞气体的Paschen击穿，该铁电体的极化强度随栅压增加而显著上升.利用上述充电方法和热刺激放电(TSD)谱的分析讨论了这类空间电荷型宏观电偶极子，及与其补偿的空间电荷热退极化的电荷动态特性；阐明了这两类俘获电荷的能阱分布，即构成宏观电偶极子的位于孔洞上下介质层内的等值异号空间电荷分别被俘获在深、浅两种能值陷阱内，而位于薄膜表面层的注入空间电荷则被俘获在中等能值陷阱中. 关键词： 反极性电晕补偿充电法 铁电驻极体 充电电流 热刺激放电     

退火对多晶ZnO薄膜结构与发光特性的影响

用射频反应溅射法在Si（111）衬底上制备了C轴取向的多晶ZnO薄膜，通过不同温度的退火处理，研究了退火对多晶ZnO薄膜结构和发光特性的影响.由x射线衍射得知，随退火温度的升高，晶粒逐渐变大，薄膜中压应力由大变小至出现张应力.光致发光测量发现，样品在430nm附近有一光致发光峰, 峰的强度随退火温度升高而减弱，联合样品电阻率随退火温度升高而逐渐变大的测量及能级图，推测出ZnO薄膜中的蓝光发射主要来源于锌填隙原子缺陷能级与价带顶能级间的跃迁. 关键词： ZnO薄膜 退火 光致发光 射频反应溅射     

主客体掺杂型非线性光学聚合物驻极体DR1/PMMA膜中空间和偶极电荷的相互作用特性

运用热刺激放电、表面电位衰减和电光效应的检测等手段,对主客体掺杂型非线性光学聚合物驻极体DR1/PMMA膜中空间和偶极电荷的相互作用特性进行了研究．结果表明,在极化后的样品中,被样品表面或体内的各类陷阱捕获的大部分空间电荷所处的陷阱能级高于极性生色团分子的定向排列产生的偶极电荷的束缚能级,空间电荷对偶极电荷有强烈的束缚作用．空间电荷衰减将导致材料内的电场分布发生变化,并引起极性生色团分子的松弛．空间电荷稳定性决定着偶极电荷的寿命. 关键词：     

热处理温度对ZnO∶Al薄膜性能的影响

利用溶胶-凝胶技术在玻璃衬底上制备了ZnO∶Al薄膜,表征了薄膜的结构、光透过和光致发光特性,探讨了热处理温度对薄膜晶体结构和光学性质的影响.结果表明,在热分解温度400 ℃和退火温度600 ℃时,ZnO∶Al薄膜的C轴择优取向明显,透过率较高.在热处理温度400 ℃情况下,激发波长340 nm的光致发光谱中有三个发光中心,紫外发光强度随退火温度的升高先升高后下降,500 ℃时发光强度最强.其它两个发光峰的强度随退火温度的升高而降低甚至消失.激发波长不同,ZnO∶Al薄膜的发光中心和强度均发生变化.     

热处理温度对ZnO：Al薄膜性能的影响

利用溶胶-凝胶技术在玻璃衬底上制备了ZnO:Al薄膜,表征了薄膜的结构、光透过和光致发光特性,探讨了热处理温度对薄膜晶体结构和光学性质的影响.结果表明,在热分解温度400 ℃和退火温度600 ℃时,ZnO:Al薄膜的C轴择优取向明显,透过率较高.在热处理温度400 ℃情况下,激发波长340 nm的光致发光谱中有三个发光中心,紫外发光强度随退火温度的升高先升高后下降,500 ℃时发光强度最强.其它两个发光峰的强度随退火温度的升高而降低甚至消失.激发波长不同,ZnO:Al薄膜的发光中心和强度均发生变化.     

串口型铁电存储器总剂量辐射损伤效应和退火特性

对一款商用串口I2C型铁电存储器进行了⁶⁰Coγ 辐射和退火实验, 研究了铁电存储器的总剂量效应和退火特性. 使用了超大规模集成电路测试系统测试了铁电存储器的DC, AC, 功能参数, 分析了辐射敏感参数在辐射和退火过程中的变化规律. 实验结果表明: 总剂量辐射在器件内产生大量氧化物陷阱电荷, 造成了铁电存储器外围控制电路MOS管阈值向负向漂移, 氧化物陷阱电荷引入附加电场使铁电薄膜受肖特基发射或空间电荷限制电流的作用, 产生辐射感生漏电流. 由于浅能级亚稳态的氧化物陷阱电荷数量上多于深能级氧化物陷阱电荷, 使得器件功能和辐射敏感参数在常温退火过程中快速恢复. 关键词： 铁电存储器 总剂量辐射 退火特性     

非掺杂ZnO薄膜中紫外与绿色发光中心

用直流反应溅射方法在硅衬底上淀积了ZnO薄膜,测量它们的光致发光(PL)光谱,观察到两个发光峰,峰值能量分别为3.18(紫外峰,UV)和2.38eV(绿峰).样品用不同温度分别在氧气、氮气和空气中热处理后,测量了PL光谱中绿峰和紫外峰强度随热处理温度和气氛的变化,同时比较了用FP-LMT方法计算的ZnO中几种本征缺陷的能级位置.根据实验和能级计算的结果,推测出ZnO薄膜中的紫外峰与ZnO带边激子跃迁有关,而绿色发光主要来源于导带底到氧错位缺陷(O_Zn)能级的跃迁,而不是通常认为的氧空 关键词： ZnO薄膜 热处理 光致发光光谱 缺陷能级     

压力膨化处理对正极性聚丙烯蜂窝膜的驻极体性质的影响

压力膨化处理工艺能够显著改善聚丙烯蜂窝薄膜（cellular polypropylene） 驻极体的压 电活性.通过热脉冲技术、表面电位衰减测量及TSD 电流谱分析等研究了经恒压正电晕充电 的聚丙烯蜂窝膜的陷阱能级分布特征，讨论了压力膨化处理工艺对这类蜂窝膜驻极体电荷稳 定性及电荷输运特性的影响.结果说明，PP 蜂窝膜内存在着位于中能级区的能值各异的三种 分立陷阱，深能值陷阱和浅能值陷阱的大多数位于孔洞膜近表面的体层或体内，而中等能值 陷阱则主要位于自由面附近.压力膨化处理改变了PP 蜂窝膜的能阱状态并在一定程度上降低 了这类孔洞膜驻极体的电荷储存稳定性，但没有明显影响其由慢再俘获效应占主导地位的脱 阱电荷输运特性. 关键词： 压力膨化处理 聚丙烯蜂窝膜 驻极体 电荷储存与陷阱分布 电荷输运     

α-Al2O3: Mn单晶的三维热释发光谱研究

测量了α-Al2O3: Mn单晶中子辐照前后的三维热释发光谱.观察到α-Al2O3: Mn:Mn单晶γ射线照射后测量的三维热释发光谱中，峰温在350℃波长为680nm处有一宽发光峰，这可能与Mn2+离子有关；波长为695nm峰温在170℃和350℃的线状光谱，叠加在680nm宽发光峰上，是Cr3+离子的发光谱线,其中可能有Mn4+离子的贡献.与纯α-Al2O3单晶的热释发光谱相比，掺入Mn杂质后，γ射线照射的三维热释发光谱中完全地抑制了波长为416nm的α-Al2O3的F心发光峰.经1017cm-2中子注量辐照和退火后，γ射线照射后测量的三维热释发光谱中，在150℃出现了波长为416和695nm的发光峰，以及在250℃波长为680和695nm的发光峰，其中695nm新发光峰的强度略超过了中子辐照前α-Al2O3:Mn在350℃波长为695nm的发光峰，说明中子辐照产生了大量浅陷阱能级和F心.然而，经1018cm-2中子注量辐照和退火后，γ射线照射后测量的三维热释发光谱中，出现了峰温150℃，190℃和250℃波长为520nm的Mn2+离子发光峰，以及300℃波长为680和695nm的Cr3+（或Mn4+）的发光峰，表明增高中子注量的辐照，产生了温度为190℃，250℃和300℃深陷阱能级和F心，并使Mn2+离子发光峰明显加强. 关键词： α-Al2O3:Mn 三维发光谱 缺陷结构 发光机理     

低密度聚乙烯热压成型过程中的空间电荷

借助开路热刺激放电(TSD)电流及原位实时电荷TSD和电荷等温衰减测量，研究了低密度聚乙烯(LDPE)在热压成型过程中所产生的空间电荷特性.结果表明具有良好室温稳定性的成型电荷被束缚在两类陷阱能级中：浅阱和深阱，其陷阱中心深度分别约为0.92eV和1.31eV.初步的分析进一步表明了它们应该分别位于试样的表层和体内，为近表面陷阱和体陷阱. 关键词： 低密度聚乙烯(LDPE) 热压成型 空间电荷 热刺激放电(TSD)     

Effect of heating treatment on trap level distribution in polyamide 66 film electrets

The effect of heating treatment on the trap level distribution in polyamide 66 film electret is studied by thermally stimulated depolarization current （TSDC） technique. For annealed polyamide 66, there are three trap levels that respectively originate from space charge trapped in amorphous phase, interphase and crystalline phase. There is one peak that originates from space charge trapped in amorphous phase for quenched one. Using multi-point method to fit the experimental curves, the detrapping current peaks can be separated and the trap depth is obtained. The shallower trap levels trapped in amorphous phase and interphase are obviously close to the deeper trap level trapped in crystalline phase for annealed polyamide 66 as the polarization temperature increases, while the trap level distribution remains unaffected by polarization temperature for quenched one.     

Annealing Effect on Chain Segment Motion and Charge Trapping and Detrapping in Nylon 1010

The chain segment motion and charge trapping and detrapping in nylon 1010 films were investigated by means of thermally stimulated depolarization current (TSDC). There were three current peaks (named α, ρ1, and ρ2 peaks, respectively) in the experimental TSDC spectra above room temperature. The α peak is attributed to a background dipole relaxation by the motion of chain segments and space charge contribution, the ρ1 peak is originated from a space charge trapped in the bulk amorphous regions and the interphase between crystalline and amorphous regions, the ρ2 peak is originated from space charge trapped in crystalline regions. By analyzing the characteristic parameters of these peaks, it was found that with in increase of the degree of crystallinity the activation energy of the a peak increased from 1.12 to 1.22 eV and the trap depth of the ρ2 peak increased from 2.70 to 2.82 eV, while the trap depth of the ρ1 peak decreased from 1.50 to 1.29 eV. Annealing induced a decrease of the chain segment mobility and promoted the creation of traps in nylon 1010. Annealing also decreased the stability of the trapped charges in the bulk amorphous and the interphase regions and increased the stability of the trapped charges in the crystalline regions.     

Effect of Polarization Temperature on the Chain Segment Motion and Space Charge Detrapping in Polyamide 610 Film Electrets

The effect of polarization temperature on the chain segment motion and charge trapping and detrapping in polyamide 610 films has been investigated by means of thermally stimulated depolarization current (TSDC) and wide-angle X-ray diffraction (WAXD). A small part of the amorphous phase of quenched polyamide 610 changes into the crystalline state with increasing polarization temperature. There are three current peaks (named α, ρ₁, and ρ₂ peak, respectively) in the TSDC spectra. The α peak corresponds to the glass transition, the ρ ₁ peak is attributed to space charge trapped in the amorphous phase, and interphase between crystalline and amorphous phases, and the ρ ₂ peak originates from space charge trapped in the crystalline phase. By analyzing the characteristic parameters of these peaks, it was found that the increase of polarization temperature induced a decrease of the chain segment mobility and promoted the creation of structural traps in polyamide 610. The decrease of the chain segment mobility in the amorphous phase made the intensity of the α peak weak and the activation energy increased. The higher the polarization temperature, the higher the degree of crystallinity and the more charge carriers trapped in the crystalline phase. So, the increase of polarization temperature made the intensity of the ρ ₂ peak strong and increased the stability of trapped charge in the crystalline phase. The increase of polarization temperature also made the intensity of the ρ ₁ peak strong and decreased the stability of trapped charge in the amorphous phase and interphase.     

The Chain Segment Motion and Traps in γ‐Irradiation Crystalline Nylon 1010

The chain segment motion, charge trapping and detrapping in γ‐irradiated nylon 1010 films (doses in the range 0–2,000 kGy were used) have been investigated by means of thermally stimulated depolarization current (TSDC). There are three current peaks (named α, ρ₁ and ρ₂, respectively) in the TSDC spectra, corrected by spontaneous current, above room temperature. By analyzing the characteristic parameters of the three peaks, it is found that the chain segment motion in the amorphous regions becomes more difficult at low irradiation dose (<100 kGy) and then becomes easier with further increasing irradiation dose. The stability of the traps at the crystalline‐amorphous interfaces increases at low irradiation dose (<500 kGy) and then decreases with further increasing irradiation dose; the irradiation promotes the creation of traps and the stability of traps in the crystalline regions.     

Effect of ionic liquid on chain segment motion and charge detrapping in poly(l-lactide)/ionic liquid composites

The effect of ionic liquid on the chain segment motion and charge detrapping in poly(l-lactide) (PLA)/ionic liquid (IL) composites has been investigated by means of thermally stimulated depolarization current (TSDC), scanning electron microscopy, and differential scanning calorimetry. There are four current peaks (namely, α, ρ₁, ρ₂, and ρ₃ peaks, respectively) in TSDC spectra of PLA and PLA/IL composites. The α peak corresponds to the glass transition, the ρ₁ peak is attributed to space charge trapped in the amorphous phase, the ρ₂ peak is originated from space charge trapped in the interphase that includes PLA/IL interface and crystalline/amorphous interface of PLA, and the ρ₃ peak is originated from space charge trapped in the crystalline phase. With the increase of IL content from 0 to 5phr, ρ₂ and ρ₃ peaks gradually merge into one single peak. By analyzing the characteristic parameters of these peaks, it is found that IL can accelerate the mobility of chain segments and increase structural defects in PLA/IL composites. In addition, IL decreases the stability of trapped charge in both amorphous and crystalline phases, but not affecting the stability of trapped charge in interphase.     

界面极化注极聚丙烯薄膜驻极体的电荷存储特性研究

本文报道一种基于双层介质界面极化机理的新型驻极体注极技术: 借助辅助层对PP薄膜进行注极. 采用表面电位测试方法考察了注极温度、注极电压对所获PP薄膜驻极体电荷存储性能的影响, 并利用热刺激放电技术研究了其高温电荷存储性能, 同时测试了PP薄膜驻极体在X和Y方向的静电场分布. 结果表明: 界面极化注极是一种比电晕注极更为优异的驻极体形成方法. 在一定温度下, 驻极体表面电位随注极电压的增加而增加, 而且两者呈线性关系, 这一结果与注极过程的电荷积聚方程的分析完全一致. 注极温度的影响研究表明, 在保持注极电压不变(注极电压范围为0.5–3.0 kV)的情况下, 温度低于75 ℃时, 温度的变化对于注极效果的影响不明显; 当注极温度大于75 ℃ 时, PP薄膜驻极体的表面电位随注极温度的增加而增加. 表面电位随时间的变化研究表明, PP薄膜驻极体具有良好的电荷存储稳定性. 对其表面电位分布的测试表明, 界面极化注极所形成的PP薄膜驻极体呈现均匀的静电场分布.     

Thermally stimulated depolarization current studies of sulfonated polystyrene ionomers

A detailed study of thermally stimulated depolarization current (TSDC) was carried out to investigate dipolar relaxation and the charge storage phenomenon in films of sulfonated polystyrene (SPS) ionomers having lithium or potassium as counterions. Differential scanning calorimetry measurements were also applied as a complementary technique, mainly to follow the change of the glass transition temperature with the amount of sulfonated groups. It was observed that, since the glass transition does not change significantly with the amount of sulfonated groups, a cluster of multiplets is expected not to be formed in the range used in this work. TSDC of SPS samples polarized at temperatures higher than the glass transition temperature showed three peaks: one at lower temperature (peak β), an intermediate peak (peak α), and a third that appeared at a temperature coincident with the polarization temperature (peak ρ). Quantitative information about trapping–detrapping and dipolar relaxation and their corresponding activation energies was determined by fittings of the deconvoluted peaks with kinetic relaxation processes.     

Evidence for electret polarization in polyoxymethylene

It has been found that under certain experimental conditions, polyoxymethylene films undergo a microscopic as well as macroscopic polarization resulting in electret formation. Thermally stimulated discharge (TSD) currents have been measured for polyoxymethylene film electrets of 100 μM prepared at various polarizing fields and polarization temperatures. Experimental evidence like the shift of the discharge current peak with polarization temperature, and a nonlinear dependence of the accumulated charge on field strength suggests the formation of a space charge and interfacial polarization. The observed TSD peak at 130°C coincides with the α -relaxation temperature in low-frequency dielectric measurements. Activation energies and relaxation times have been calculated on the basis of the experimental data.     

孔洞聚丙烯驻极体膜中空间电荷与孔洞击穿电荷的俘获特性

对孔洞聚丙烯(PP)驻极体膜系统的研究结果表明：孔洞PP膜中空间电荷的俘获特性随注入的空间电荷量或试样表面电位而变化,注入的电荷量较少时空间电荷主要被俘获在表面深陷阱和近表面次深陷阱中,较多的注入电荷量时空间电荷在进一步填充表层(表面和近表面)陷阱的同时,还将填充体内浅陷阱;这三类陷阱中心所对应的电荷脱阱温度分别约为160℃,138℃和92℃.而孔洞击穿电荷不仅被俘获在与试样表层空间电荷陷阱相似的孔洞表层陷阱中,还有相当的量穿过孔洞表层进入体内、成为浅阱俘获孔洞击穿电荷. 关键词： 孔洞聚丙烯膜 空间电荷 孔洞击穿电荷 俘获特性