秸秆含氮模型化合物热解氮转化规律的实验研究

采用TG-FTIR联用实验系统,在氩气氛围下研究了含氮模型化合物甘氨酸酐热解失重特性以及NO_x前驱物的释放特性;研究了K、Ca、Fe金属盐对甘氨酸酐热解氮转化的影响。结果表明,在20、40、60℃/min升温速率下,NH₃、HCN、HNCO为甘氨酸酐热解的主要气相含氮产物,其中,NH₃产率最大,HCN次之,HNCO生成量最小;随升温速率增加,TG失重曲线右移,热解剩余物减少;且HCN和HNCO的产率增加,NH₃产率降低;K、Ca、Fe盐均对甘氨酸酐热解氮转化具有催化作用,其中,K、Ca有利于促进NH₃、HCN的生成,Fe对HCN的生成具有促进作用,但对NH₃的生成起到抑制作用。     

富N生物质原料气化过程NOx前驱物生成特性及规律

基于水平管式反应器气化条件，结合化学吸收-分光光度法和X射线光电子能谱（XPS）分析，研究了四种富氮生物质（豆秆（SBS）、稻秆（RS）、玉米秆（CS）和中密度纤维板（MDF））气化过程NO_x前驱物生成特性及规律，对比考察了燃料特性（燃料N官能团、N含量）及气化条件（温度、气化介质）的影响。结果表明，NH₃-N为主要NO_x前驱物并伴随一定量的HCN-N，绝大部分形成于初次裂解和二次反应同时进行的挥发分析出阶段。各因素通过影响NO_x前驱物组分生成路径而改变其产率：燃料特性对产率的影响主要体现在N官能团（胺类-N（N-A）类型）稳定性方面，与N含量关系不大，因不稳定N-A在初次裂解中的关键作用，MDF总产率高达74.7%（质量分数），比秸秆类平均总产率高出15%（质量分数）；温度和气化介质会影响二次反应中与NO_x前驱物相关的反应路径（特别是加氢氢化反应），秸秆SBS气化，温度从800℃到1000℃，NH₃-N产率从38.9%（质量分数）增加至47.7%（质量分数），HCN-N产率先增加后减少，峰值为18.3%（质量分数），源于各反应路径受温度影响的平衡性；气化介质改变加氢氢化反应，CO₂主要影响HCN-N，起一定抑制作用，H₂O主要影响NH₃-N，起促进作用，因此，通过调节气化介质比例可一定程度改变NO_x前期物组分的选择性。     

玉米芯水解残渣热解焦气化反应性研究

利用热重分析仪研究了玉米芯及其酸水解残渣热解焦的气化反应性,重点考察了热解温度、升温速率、气化温度和气化介质(CO₂、H₂O)对残渣热解焦气化反应性的影响,并借助SEM观测了热解焦的表观形貌。结果表明,残渣热解焦的气化反应性较玉米芯热解焦有所下降;在热解温度550~850 ℃,残渣热解焦的气化反应性随热解温度提高而降低,在热解升温速率0.1 K/s下制取的热解焦,其气化反应性低于15.0 K/s下的热解焦;在气化温度850~950 ℃,提高气化反应温度和使用水蒸气作为气化介质能显著提高残渣热解焦的气化反应性;采用混合反应模型计算了残渣热解焦的气化反应动力学参数。     

升温速率对胜利褐煤热解过程中N迁移转化的影响

在固定床/流化床管式石英反应器中进行了胜利褐煤的快速热解和慢速热解实验,考察了升温速率对N迁移转化及对半焦内部N化学形态变化的影响。研究结果表明,快速升温热解气相N(NH₃和HCN)生成量明显高于慢速热解时的生成量,且随着温度的升高,两者差值均逐渐增大。在多数情况下,NH₃或HCN的产率在973 K左右并不随温度的升高而增加,这与高温下的半焦热缩聚反应以及挥发分的二次反应有关。快速热解条件下,半焦N的释放速率要快于半焦炭本身失重速率。X射线光电子能谱(XPS)分析认为,热解使得吡咯型N(N-5)部分转化为吡啶型N(N-6)和季氮型N(N-Q),快速热解有利于生成N-6,而慢速热解下半焦中N-Q含量较高。     

水热炭化生物质与煤共热解和共气化特性研究

煤和生物质共热化学转化有助于当前化石能源系统的低碳化发展。本研究以烟煤和木质生物质为原料,研究煤和生物质共热解和共气化特性,并考察了不同水热炭化温度和生物质掺混比的影响。利用热重分析仪和在线质谱分析共热解和共气化的协同作用和氢气释放特性。采用Model-fitting方法,单独分析热解和气化阶段的整体反应动力学。结果表明,煤和生物质共气化阶段的协同作用显著强于共热解阶段。生物质比例越高,共气化协同作用越明显,水热炭化会削弱共气化的协同作用。共热解过程,H₂的产生受抑制。共气化过程可采用一级模型描述,而共热解过程需遵循n级反应模型。未处理的或轻度水热炭化的生物质与煤的混合物,共热解整体活化能和反应级数大于加权平均值,而其共气化的活化能变化趋势相反。重度水热炭化生物质与煤的混合物,共热解和共气化的活化能均接近加权平均值。     

生物质热解过程中NO、NH3和HCN的释放特性

在氩气气氛下,利用固定床反应器对稻草（DC）、麦杆（MG）和锯末（JM）三种生物质进行热解实验,采用傅里叶变换红外光谱仪（FT-IR）在线检测热解气体产物中的含氮组分,分析各种气相含氮组分的释放规律。实验结果表明,由于锯末中木质素含量较高,锯末热解开始快速释放NO、NH₃和HCN的温度明显高于稻草和麦杆。稻草热解过程中生成的NH₃、HCN和NO量最大。低温下NH₃的生成至少部分与生物质中氨基结构的分解有关,HCN的生成温度较高。不同生物质热解过程中NO、NH₃和HCN释放特性的差异,是由生物质大分子结构不同、灰分含量及成分不同、N含量不同等决定的,以及氮在生物焦、焦油和气相间的分配差异造成的。     

升温速率对生物质热解的影响

稻壳、稻秆及麦秆是中国主要的农业废弃物,如何综合、有效地利用这些农业废弃物进行资源化研究显得十分必要。热解是热化学转化中最为基本的过程,是气化、液化及燃烧过程的初始和伴生反应,对热解的分析有助于热化学转化过程控制及高效转化工艺的开发。目前,国内外对生物质及其组分的热解已有大量的研究,但对中国主要的农业废弃物稻壳、稻秆及麦秆的研究较少。本研究利用热重和红外联用技术深入研究了升温速率对三种典型生物质热解气体产物的影响,并对生物质的热解动力学及热解气体产物的析出规律进行实时在线分析。     

印刷电路板中环氧树脂热解的ReaxFF反应动力学模拟

采用ReaxFF动力学方法模拟了非交联固化环氧树脂在不同温度和升温速率下的热解特性. 结果表明, 含N和含O桥键的断裂是热解的引发反应. 观察到H₂O的4种主要的生成途径, 而这些反应途径都涉及到含羟基的前驱体. 当反应温度较低时, H₂O为热解的主要产物. 而在高温条件下, 热解的主要产物为H₂, 它主要为分子内/分子间脱氢反应和氢自由基的夺氢反应的产物; 高温同时促进了含石墨烯结构且分子量较大的碳团簇的形成. 除此之外, 还观察到了CH₄, HCN, NH₃和CO等小分子产物. 本文用ReaxFF动力学方法模拟所得的气体产物以及含类似石墨烯结构的碳团簇与实际实验结果一致, 说明ReaxFF动力学方法能为从分子水平上研究有机物高温热解反应提供了一种有效的途径.     

玉米秸热解动力学研究

生物质能具有低硫和二氧化碳零排放的特点，其在能源结构中的地位越来越重要。作为一种高效生物质能转化途径，热化学转化可获得气、液和固态多种能源产物。其中，热解是热化学转化中最为基本的过程，是气化、液化及燃烧过程的初始和伴生反应，对热解的分析有助于热化学转化过程控制及高效转化工艺的开发。热解动力学是表征热解过程中反应过程参数对原料转化率影响的重要手段，通过动力学分析可深入了解反应过程和机理，预测反应速率及难易程度，为生物质热化学转化工艺的研究开发提供重要的基础数据。国外对纤维素热解动力学已进行了一些研究，但生物质作为纤维素、半纤维素、木质素等的复杂聚合物，其热解行为与单纯纤维素差别较大。因此本文的热解研究集中在玉米秸这种常见的软质秸秆类生物质原料。     

富氮生物质原料热解过程中NO_x前驱物释放特性研究

利用热重分析-傅里叶红外光谱联用(TG-FTIR)和水平管式炉-X射线光电子能谱(XPS)研究了两种富氮生物质原料(大豆秸秆(SBS)和纤维板(FB))热解过程中NO_x前驱物(NH_3、HCN和HNCO)的释放特性,考察温度、升温速率及燃料含N物质结构对其NO_x前驱物释放行为的影响。结果表明,燃料中的N来源不同(天然固有与人工添加)造成其转化差异:SBS释放的NO_x前驱物主要为NH_3而FB为NH_3、HCN(快速)和HNCO(慢速);FB气相N主要随挥发分析出,而SBS则相反,在二次反应阶段析出;两种燃料中N的转化随温度变化,低温下富集于半焦N,600℃以上时更多向非半焦N转移,NO_x前驱物以NH_3为主,高温及高升温速率利于HCN生成,若以减排NO_x为目的,热解温度控制在600℃为佳;两种燃料中N的结构均为胺类N(N-A),热解时部分N-A向半焦中杂环N转化,同时伴随杂环N分解;高温下吡啶N和吡咯N分解分别主要产生HCN和NH_3。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.