SYNTHESIS OF POLYPROPYLENE-POLY(METH)ACRYLATE BLOCK COPOLYMERS USING METALLOCENE CATALYZED PROCESSES AND SUBSEQUENT ATOM TRANSFER RADICAL POLYMERIZATION

ABSTRACT

The synthesis of block copolymers containing low molar mass polypropylene and poly(meth)acrylates is reported. Vinyl-terminated polypropylene (M_n SEC=3,100; M_w/M_n=1.45) was used to prepare a macroinitiator for atom transfer radical polymerization (ATRP) via hydrosilation with 1-(2-bromoisobutyryloxy)propyl-tetramethyldisiloxane. Polar segments were then incorporated to polypropylene by chain extension using either methyl methacrylate, or n-butyl acrylate. While blocking efficiency was limited in this system, well-defined PP-b-PMMA (M_n=22,220; M_w/M_n=1.14) was obtained by extraction of unreacted polypropylene with diethyl ether.     

Hydrogen bond mediated self-assembly of two diblock copolymers

Two chemically dissimilar diblock copolymers, polybutadiene-b-poly(acrylic acid), PBd-b-PAA (M_w = 5.8–4 kg mol⁻¹) and poly(styrene)-b-poly(ethylene oxide), PS-b-PEO (M_w = 9–5 kg mol⁻¹) were blended in an effort to achieve morphologies typical of triblock copolymers. Blend compatibility was achieved by the hydrogen bond driven association of the PAA block of one diblock with the PEO block of the other. Small angle X-ray scattering was used to determine the morphologies of the compositions, which were further investigated using transmission electron microscopy and selective staining techniques. The crystallinity of the PEO block was determined by differential scanning calorimetry. The hydrogen bond interactions between PEO and PAA yielded a complex triblock lamellar morphology of the form PS-b-(PEO/PAA)-b-PBd-b-(PEO/PAA). This morphology was stable when crystallization of PEO was suppressed by sufficient interaction with PAA.     

Synthesis,structure, and property of well‐defined polymethylene‐based diblock copolymers by a combination of living polymerization of ylides and atom transfer radical polymerization

A combination of living polymerization of ylides and atom transfer radical polymerization (ATRP) was used successfully in the design and synthesis of well‐defined polymethylene‐b‐poly(methyl methacrylate) (PM‐b‐PMMA) and polymethylene‐b‐poly(n‐butyl acrylate) (PM‐b‐Pn‐BuA). Tripolymethylene borane were firstly synthesized by living polymerization of dimethylsulfoxonium methylides and then oxidated quantitatively through trimethylamine‐N‐oxide dihydrate to provide a series of low‐polydispersity hydroxyl‐terminated polymethylenes (PM‐OHs) with different molecular weight. Subsequently, such polymers were converted into polymethylene‐based macroinitiators (PM‐MIs, M_n(GPC) = 1900–10,400 g/mol; M_w/M_n = 1.12–1.23) in ～100% conversion. ATRPs of methyl methacrylate and n‐butyl acrylate were successfully conducted using PM‐MI to produce well‐defined diblock copolymers of PM‐b‐PMMA and PM‐b‐Pn‐BuA, respectively. The GPC traces indicated the successful extension of PMMA and Pn‐BuA segment (M_n(GPC) of PM‐b‐PMMA = 3980–10,100 g/mol; M_w/M_n = 1.16–1.22; M_n of PM‐b‐Pn‐BuA = 7400–9200 g/mol; M_w/M_n = 1.14–1.18). Atomic force microscopy (AFM) was used to characterize the structures of the precipitated PM‐b‐PMMA micelles, which were formed in toluene. The blend of LDPE/PMMA was prepared with PM‐b‐PMMA as compatibilizer. The scanning electron microscopy (SEM) results showed that the compatibilization of the LDPE/PMMA was improved greatly by the incorporation of PM‐b‐PMMA. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5671–5681, 2009     

Polypropylene-block-poly(methyl methacrylate) and-block-poly(N-isopropylacrylamide) block copolymers prepared by controlled radical polymerization with polypropylene macroinitiator

Polypropylene-block-poly(methyl methacrylate) (PP-b-PMMA) and Polypropylene-block-poly(N-isopropylacryramide) (PP-b-PNIPAAm) block copolymers were successfully synthesized by radical polymerizations of MMA or NIPAAm with polypropylene (PP) macroinitiators. Polypropylene macroinitiators were prepared by a series of end functionalization of pyrolysis PP via hydroalumination, oxidation and esterification reactions. The PP macroinitiators thus obtained could initiate radical polymerizations of MMA or NIPAAm by using transition metal catalyst systems, and ¹H NMR analysis and gel permeation chromatography measurement confirmed the formation of PP-b-PMMA and PP-b-PNIPAAm block copolymers. In addition, the length of the incorporated PMMA or PNIPAAm segments in these block copolymers was controllable by the feed ratio between the monomer and the PP macroinitiator, and their molecular weights were estimated to be 35700 and 68700 (PMMA) and 1760 and 13300 (PNIPAAm), respectively. Transmission electron microscopy of the polymers obtained by NIPAAm polymerization revealed specific morphological features that reflected the difference of PNIPAAm segment length. The text was submitted by the authors in English.     

Encapsulation of nanomaterials using an intermediary layer cross‐linkable ABC triblock copolymer

For the preparation of core‐shell nanoparticles containing functional nanomaterials, a photo‐cross‐linkable amphiphilic ABC triblock copolymer, poly(ethylene glycol)‐b‐poly(2‐cinnamoyloxyethyl methacrylate)‐b‐poly(methyl methacrylate) (PEG‐PCEMA‐PMMA), was synthesized. This triblock copolymer was then used to encapsulate Au nanoparticles or pyrene. The triblock copolymer of PEG‐b‐poly(2‐hydroxyethyl methacrylate)‐b‐PMMA (PEG‐PHEMA‐PMMA) (M_n = 15,800 g/mol, M_w/M_n = 1.58) was first synthesized by activators generated by electron transfer atom transfer radical polymerization. Its middle block was then functionalized with cinnamoyl chloride. The degrees of polymerization of the PEG, PHEMA, and PMMA blocks were 45, 13, and 98, respectively. PMMA‐tethered Au nanoparticles (with an average diameter of 3.0 nm) or pyrene was successfully encapsulated within the PEG‐PCEMA‐PMMA micelles. The intermediary layers of the micelles were then cross‐linked by UV irradiation. The spherical structures of the PEG‐PCEMA‐PMMA micelles containing Au nanoparticles or pyrene were not changed by the photo‐cross‐linking process and they showed excellent colloidal stability. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 4963–4970, 2009     

Electroactive methacrylate‐based triblock copolymer elastomer for actuator application

A series of ABA triblock copolymers of methyl methacrylate (MMA) and dodecyl methacrylate (DMA) [poly(MMA‐b‐DMA‐b‐MMA)] (PMDM) were synthesized by Ru‐based sequential living radical polymerization. For this, DMA was first polymerized from a difunctional initiator, ethane‐1,2‐diyl bis(2‐chloro‐2‐phenylacetate) with combination of RuCl₂(PPh₃)₃ catalyst and nBu₃N additive in toluene at 80 °C. As the conversion of DMA reached over about 90%, MMA was directly added into the reaction solution to give PMDM with controlled molecular weight (M_w/M_n ≤ 1.2). These triblock copolymers showed well‐organized morphologies such as body centered cubic, hexagonal cylinder, and lamella structures both in bulk and in thin film by self‐assembly phenomenon with different poly(methyl methacrylate) (PMMA) weight fractions. Obtained PMDMs with 20–40 wt % of the PMMA segments showed excellent electroactive actuation behaviors at relatively low voltages, which was much superior compared to conventional styrene‐ethylene‐butylene‐styrene triblock copolymer systems due to its higher polarity derived from the methacrylate backbone and lower modulus. © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Synthesis and micelle formation of triblock copolymers of poly(methyl methacrylate)-b-poly(ethylene oxide)-b-poly(methyl methacrylate) in aqueous solution

Amphiphilic triblock copolymers of poly(methyl methacrylate)-b-poly(ethylene oxide)-b-poly(methyl methacrylate) (PMMA-b-PEO-b-PMMA) with well-defined structure were synthesized via atom transfer radical polymerization (ATRP) of methyl methacrylate (MMA) initiated by the PEO macroinitiator. The macroinitiator and triblock copolymer with different PMMA and/or PEO block lengths were characterized with ¹H and ¹³C NMR and gel permeation chromatography (GPC). The micelle formed by these triblock copolymers in aqueous solutions was detected by fluorescence excitation and emission spectra of pyrene probe. The critical micelle concentration (CMC) ranged from 0.0019 to 0.016 mg/mL and increased with increasing PMMA block length, while the PEO block length had less effect on the CMC. The partition constant K_v for pyrene in the micelle and in aqueous solution was about 10⁵. The triblock copolymer appeared to form the micelles with hydrophobic PMMA core and hydrophilic PEO loop chain corona. The hydrodynamic radius R_h,app of the micelle measured with dynamic light scattering (DLS) ranged from 17.3 to 24.0 nm and increased with increasing PEO block length to form thicker corona. The spherical shape of the micelle of the triblock copolymers was observed with an atomic force microscope (AFM). Increasing hydrophobic PMMA block length effectively promoted the micelle formation in aqueous solutions, but the micelles were stable even only with short PMMA blocks.     

Thermal crosslinking of poly(methyl methacrylate) by reaction of methyl ester and quaternary ammonium salt and application to (meth)acrylate-based TPEs

Copolymers of N-vinylbenzyl N-methyl pyrrolidinium chloride (VBMPC) and methyl methacrylate, PVBMPC-co-poly(methyl methacrylate) (PMMA), were synthesized by free-radical copolymerization and proved to be prone to crosslinking as a result of the reaction of methyl ester groups with benzyl methyl pyrrolidinium chloride (BMPC) moieties at temperatures higher than 110 °C. When the VBMPC content was lower than 20 wt %, these copolymers were miscible with homo-PMMA. Blends of homo-PMMA and PVBMPC-co-PMMA fully could be cured above 150 °C, when the molecular weight of PMMA exceeded 10,000 and the VBMPC content of the copolymer was higher than 5 wt %. This reaction was carried out to crosslink selectively the PMMA microdomains of PMMA-b-poly(isooctyl acrylate) (PIOA)-b-PMMA (MIM) triblock copolymers to explain the mechanism for the mechanical failure of fully (meth)acrylic thermoplastic elastomers. Comparison of the ultimate tensile properties of MIM block copolymers, when the dispersed PMMA phases and PIOA matrix were crosslinked, led to the conclusion that the ductile failure of the hard PMMA microdomains rather than the elastic failure of the PIOA matrix was the reason for the mechanical failure of MIM triblocks. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 4402–4411, 1999     

Titanium‐mediated [CpTiCl2(OEt)] ring‐opening polymerization of lactides: A novel route to well‐defined polylactide‐based complex macromolecular architectures

Among three cyclopentadienyl titanium complexes studied, CpTiCl₂(OEt), containing a 5% excess CpTiCl₃, has proven to be a very efficient catalyst for the ring‐opening polymerization (ROP) of L ‐lactide (LLA) in toluene at 130 °C. Kinetic studies revealed that the polymerization yield (up to 100%) and the molecular weight increase linearly with time, leading to well‐defined PLLA with narrow molecular weight distributions (M_w/M_n ≤ 1.1). Based on the above results, PS‐b‐PLLA, PI‐b‐PLLA, PEO‐b‐PLLA block copolymers, and a PS‐b‐PI‐b‐PLLA triblock terpolymer were synthesized. The synthetic strategy involved: (a) the preparation of OH‐end‐functionalized homopolymers or diblock copolymers by anionic polymerization, (b) the reaction of the OH‐functionalized polymers with CpTiCl₃ to give the corresponding Ti‐macrocatalyst, and (c) the ROP of LLA to afford the final block copolymers. PMMA‐g‐PLLA [PMMA: poly(methyl methacrylate)] was also synthesized by: (a) the reaction of CpTiCl₃ with 2‐hydroxy ethyl methacrylate, HEMA, to give the Ti‐HEMA‐catalyst, (b) the ROP of LLA to afford a PLLA methacrylic‐macromonomer, and (c) the copolymerization (conventional and ATRP) of the macromonomer with MMA to afford the final graft copolymer. Intermediate and final products were characterized by NMR spectroscopy and size exclusion chromatography, equipped with refractive index and two‐angle laser light scattering detectors. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1092–1103, 2010     

Surface structure of thin asymmetric PS-b-PMMA diblock copolymers investigated by atomic force microscopy

Asymmetric poly(styrene-b-methyl methacrylate) (PS-b-PMMA) diblock copolymers of molecular weight M_n = 29,700 g mol⁻¹ (M_PS = 9300 g mol⁻¹M_PMMA = 20,100 g mol⁻¹, PD = 1.15, χ_PS = 0.323, χ_PMMA = 0.677) and M_n = 63,900 g mol⁻¹ (M_PS = 50,500 g mol⁻¹, M_PMMA = 13,400 g mol⁻¹, PD = 1.18, χ_PS = 0.790, χ_PMMA = 0.210) were prepared via reversible addition-fragmentation chain transfer (RAFT) polymerization. Atomic force microscopy (AFM) was used to investigate the surface structure of thin films, prepared by spin-coating the diblock copolymers on a silicon substrate. We show that the nanostructure of the diblock copolymer depends on the molecular weight and volume fraction of the diblock copolymers. We observed a perpendicular lamellar structure for the high molar mass sample and a hexagonal-packed cylindrical patterning for the lower molar mass one. Small-angle X-ray scattering investigation of these samples without annealing did not reveal any ordered structure. Annealing of PS-b-PMMA samples at 160 °C for 24 h led to a change in surface structure.     

The effect of structure on the thermoresponsive nature of well‐defined poly(oligo(ethylene oxide) methacrylates) synthesized by ATRP

Statistical copolymers of di(ethylene glycol) methyl ether methacrylate (MEO₂MA) and tri(ethylene glycol) methyl ether methacrylate (MEO₃MA) were synthesized by atom transfer radical polymerization (ATRP) providing copolymers with controlled composition and molecular weights ranging from M_n = 8,300–56,500 with polydispersity indexes (M_w/M_n) between 1.19 and 1.28. The lower critical solution temperature (LCST) of the copolymers increased with the mole fraction of MEO₃MA in the copolymer over the range from 26 to 52 °C. The average hydrodynamic diameter, measured by dynamic light scattering, varied with temperature above the LCST. These two monomers were also block copolymerized by ATRP to form polymers with molecular weight of M_n = 30,000 and M_w/M_n from 1.12 to 1.21. The LCST of the block copolymers shifted toward the LCST of the major segment, as compared to the value measured for the statistical copolymers at the same composition. As temperature increased, micelles, consisting of aggregated PMEO₂MA cores and PMEO₃MA shell, were formed. The micelles aggregated upon further heating to precipitate as larger particles. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 194–202, 2008     

Synthesis of novel three‐arm star azo side‐chain liquid crystalline polymer via ATRP and photoinduced surface relief gratings

A three‐arm star azo side‐chain liquid crystalline (LC) homopolymer, poly[6‐(4‐methoxy‐4‐oxy‐azobenzene) hexyl methacrylate] (PMMAZO), was synthesized by atom transfer radical polymerization (ATRP) method. The polymerization of 6‐(4‐methoxy‐4‐oxy‐azobenzene) hexyl methacrylate proceeded in a controlled/“living” way. A series of three‐arm star LC block copolymers (PMMAZO‐b‐PMMA) were also synthesized. The polymers were characterized by ¹H NMR, gel permeation chromatograph, and UV–vis spectra, respectively. The both polymers of PMMAZO and copolymers of PMMAZO‐b‐PMMA exhibited a smetic phase and a nematic phase. As concern to the PMMAZO, the glass‐transition temperature (T_g) and phase‐transition temperature from the smetic to nematic phase and from the nematic to isotropic phase increased with the increase of molecular weight (M_n(GPC)) of PMMAZO. The phase transition temperature of the block copolymers, PMMAZO‐b‐PMMA, with the same PMMA block was similar to that of PMMAZO. However, the T_g of the PMMAZO‐b‐PMMA decreased at low azo content and then increased with the increasing M_n(GPC) when azo content was above 61.3%. With illumination of linearly polarized Kr⁺ laser beam at modest intensities (35 mW/cm²), significant surface relief gratings formed on PMMAZO films with different molecular weights were observed. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 777–789, 2008     

Synthesis and morphology of polyethylene‐block‐poly(methyl methacrylate) through the combination of metallocene catalysis with living radical polymerization

Polyethylene‐block‐poly(methyl methacrylate) (PE‐b‐PMMA) was successfully synthesized through the combination of metallocene catalysis with living radical polymerization. Terminally hydroxylated polyethylene, prepared by ethylene/allyl alcohol copolymerization with a specific zirconium metallocene/methylaluminoxane/triethylaluminum catalyst system, was treated with 2‐bromoisobutyryl bromide to produce terminally esterified polyethylene (PE‐Br). With the resulting PE‐Br as an initiator for transition‐metal‐mediated living radical polymerization, methyl methacrylate polymerization was subsequently performed with CuBr or RuCl₂(PPh₃)₃ as a catalyst. Then, PE‐b‐PMMA block copolymers of different poly(methyl methacrylate) (PMMA) contents were prepared. Transmission electron microscopy of the obtained block copolymers revealed unique morphological features that depended on the content of the PMMA segment. The block copolymer possessing 75 wt % PMMA contained 50–100‐nm spherical polyethylene lamellae uniformly dispersed in the PMMA matrix. Moreover, the PE‐b‐PMMA block copolymers effectively compatibilized homopolyethylene and homo‐PMMA at a nanometer level. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3965–3973, 2003     

Construction of PIB‐b‐PDEAEMA well‐defined amphiphilic diblock copolymers via sequential living carbocationic and RAFT polymerization

A series of well‐defined amphiphilic diblock copolymers consisting of hydrophobic polyisobutylene (PIB) and hydrophilic poly(2‐(diethylamino)ethyl methacrylate) (PDEAEMA) segments was synthesized via the combination of living carbocationic polymerization and reversible addition fragmentation chain transfer (RAFT) polymerization. Living carbocationic polymerization of isobutylene followed by end‐capping with 1,3‐butadiene was first performed at ?70 °C to give a well‐defined allyl‐Cl‐terminated PIB with a low polydispersity (M_w/M_n =1.29). This end‐functionalized PIB was further converted to a macromolecular chain transfer agent for mediating RAFT block copolymerization of 2‐(diethylamino)ethyl methacrylate at 60 °C in tetrahydrofuran to afford the target well‐defined PIB‐b‐PDEAEMA diblock copolymers with narrow molecular weight distributions (M_w/M_n ≤1.22). The self‐assembly behavior of these amphiphilic diblock copolymers in aqueous media was investigated by fluorescence spectroscopy and transmission electron microscope, and furthermore, their pH‐responsive behavior was studied by UV‐vis and dynamic light scattering. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1478–1486     

Characterization and degradation of the poly(methylphenylsiloxane)–poly(methyl methacrylate) graft copolymer

Poly(methylphenylsiloxane)–poly(methyl methacrylate) graft copolymers (PSXE-g-PMMA) were prepared by condensation reaction of poly(methylphenylsiloxane)-containing epoxy resin (PSXE) with carboxyl-terminated poly(methyl methacrylate) (PMMA), and they were characterized by gel permeation chromatography (GPC), infrared (IR), and ²⁹Si and ¹³C nuclear magnetic resonance (NMR). The microstructure of the PSXE-g-PMMA graft copolymer was investigated by proton spin–spin relaxation T₂ measurements. The thermal stability and apparent activation energy for thermal degradation of these copolymers were studied by thermogravimetry and compared with unmodified PMMA. The incorporation of poly(methylphenylsiloxane) segments in graft copolymers improved thermal stability of PMMA and enhanced the activation energy for thermal degradation of PMMA. © 1998 John Wiley & Sons, Inc. J. Polym. Sci. A Polym. Chem. 36: 2521–2530, 1998     

Synthesis of Core-Shell Particles of Polystyrene and Poly(methyl methacrylate) Using Emulsion Photopolymerization

Summary: Submicron core-shell particles of polystyrene (PS) and polystyrene-co-poly(methyl methacrylate) (PS-co-PMMA) coated with PMMA were obtained by emulsion photopolymerization. The seeds of PS or PS-co-PMMA were prepared by emulsion polymerization with or without emulsifier and a ratio of functional monomer and crosslinker (SVBS/EDGMA) in order to obtain different surfaces for the subsequent coating with PMMA. At each stage, the evolution of the average particle size were monitored by using photon correlation spectroscopy (DLS) and the final polymer particles was analyzed via transmission electron microscopy (TEM) and differential scanning calorimetry (DSC). The core-shell morphology was identified as the increase of the average particle size in the second stage by DLS technique and by the direct observation by TEM of the differentiation between PS core and PMMA shell, and by the presence of two glass transition temperatures (T_g) as a consequence of the existence of two partially miscible phases.     

Systhesis of double-hydrophilic core-shell type multiarm star copolymer polyethylenimine-block-poly(2-hydroxyethyl methacrylate

Multiarm star block copolymers hyperbranched polyethylenimine-b-poly(2-hydroxyethyl methacrylate) (HPEI-b-PHEMA) with average 28 PHEMA arms have been prepared by atom transfer radical polymerization (ATRP) of HEMA in a mixed solvent of methanol and water using a core-first strategy. The hyperbranched macroinitiator employed was prepared on the basis of well-defined hyperbranched polyethylenimine with Mw/Mn of 1.04 by amidation with 2-bromo-isobutyryl bromide. The polymerization condition was optimized to prepare star copolymers with narrow dispersity, and the variables included the volume ratio of methanol to water, the molar ratio of initiating site to CuCl and the molar ratio of [CuCl]:[CuBr2]. Under the optimized polymerization condition, the lowest Mw/Mn value of the obtained star copolymers was around 1.3. Kinetic analysis showed that an induction period existed in the polymerization of HEMA. After this induction period, a linear dependence of ln([M]0/[M]t) on time was observed. The obtained HPEI-b-PHEMA could adsorb hydrophilic molecules. The comparison with the star copolymer with hydrophobic core and hydrophilic PHEMA shell verified that both the hydrophilic core and shell could host the hydrophilic guests, but the amidated HPEI core was more effective than the PHEMA shell.     

Preferred-handed helical conformation in organic–inorganic hybrid block copolymers with well-controlled stereoregularity

A novel block copolymer containing polyhedral oligomeric silsesquioxanes (POSS) features a well-controlled stereoregularity, that is, isotactic polymethacrylate-functionalized POSS-b-polymethyl methacrylate (it-PMAPOSS-b-PMMA), was prepared via controlled-anionic polymerization. The stereoregularity of each segment in the it-PMAPOSS-b-PMMA is evaluated using nuclear magnetic resonance (NMR) spectroscopy, which reveals an isotactic configuration in both the PMAPOSS and PMMA segments. The secondary structure of it-PMAPOSS-b-PMMA in a mixture with a small chiral dopant is clarified with electronic circular dichroism and vibrational circular dichroism measurements. By adding a chiral dopant, a controlled preferential helical conformation of the unilateral segment in achiral it-PMAPOSS-b-PMMA is achieved.     

Chemoenzymatic synthesis amphiphilic H-shaped copolymer and its self-assembly behavior

ABA triblock copolymers were synthesized by dihydroxyl-capped PEO initiated enzymatic ring-opening polymerization (eROP) of ε-CL in the presence of biocatalyst Novozyme 435. The chains ended with hydroxyl of block copolymers were modified by the esterification of 2,2-dichloro acetyl chloride (DCAC) to obtain the tetrafunctional macroinitiator, which was used in the ATRP of 4-vinylpyridine (4-VP). CuCl/HMTETA was used as the catalyst system in the ATRP of 4-VP to acquire the H-shaped block copolymers (PVP)₂-b-PCL-b-PEG-b-PCL-b-(PVP)₂. The H-shaped block copolymers were characterized by FTIR, NMR, and GPC. Copolymers with high molecular weights (M _n = 46121 g/mol) and low polydispersities (M _w/M _n = 1.30) were prepared. Moreover, the morphology of the copolymer was examined with dynamic light scattering (DLS) and atomic force microscopy (AFM). Spherical micelles with a diameter of 70 nm in aqueous solution were obtained.     

Synthesis of block and star copolymers by photoinduced radical coupling process

The general design for the synthesis of AB diblock, and A₂B and AB₂ star copolymers based on the statistical coupling of poly(styrene) (PSt) and poly (methyl methacrylate) (PMMA) macromolecules containing photoreactive benzophenone is presented. For this purpose, mono- and bifunctional initiators for Atom Transfer Radical Polymerization (ATRP) bearing benzophenone group were synthesized and characterized. End- and mid-chain benzophenone functional PSt and PMMA with low molecular weights were obtained by ATRP using these initiators in the presence of CuBr/N,N,N′,N″,N″-pentamethyldiethylenetriamine (PMDETA) catalytic complex. Poly(styrene-block-methyl methacrylate) (PSt-b-PMMA) copolymers were prepared by photolysis of the solutions containing end functional PSt and PMMA in THF at λ = 350 nm for 60 min in the presence of a hydrogen donor such as N-methyldiethanolamine (NMDEA). The proposed mechanism assumes hydrogen abstraction of photoexcited benzophenone moiety by NMDEA. Ketyl radicals resulting from abstraction reaction undergo radical-radical coupling to form benzpinacol structure at the core. Formation of A₂B and AB₂ type star copolymers upon irradiation of solutions containing appropriate combinations of end- and mid-chain functional polymers was also demonstrated. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2938–2947, 2009