Structure and nanomechanical characterization of electrospun PS/clay nanocomposite fibers

Electrospinning has been emerging as one of the most efficient methods to fabricate polymer nanofibers. In this paper, PS/clay nanocomposite fibers with varying diameters were electrospun onto solid substrates. The fiber diameters were adjusted from 4 microm to 150 nm by changing the solution concentration. Scanning electron microscopy (SEM), transmission electron microscopy (TEM), and atomic force microscopy (AFM) were used to characterize the fiber morphology. Shear modulation force microscopy (SMFM) was utilized to investigate the surface nanomechanical properties of electrospun fibers as a function of the fiber diameter and temperature. In the absence of clay, no change in T(g) was observed, even though a large increase of shear modulus below the glass transition temperature was found. This effect was postulated to result from the molecular chain alignment during electrospinning. The addition of functionalized clays to the spinning solution produced fibers with a highly aligned montmorillonite layer structure at a clay concentration of 4 wt %. Clay agglomerates were observed at higher concentrations. The existence of clay further enhanced the shear modulus of fibers and increased the glass transition temperature by nearly 20 degrees C.     

Phase morphology and mechanical properties of the electrospun polyoxymethylene/polyurethane blend fiber mats

Polyoxymethylene/thermoplastic polyurethane (POM/TPU) blends containing 10–30 wt % of TPU were electrospun using hexafluoroisopropanol as the solvent. The average fiber diameter increases with the increase in TPU content from 0.68 μm for neat POM fibers to 0.92 μm for POM/TPU 7:3 blend fibers due to the increase in solution viscosity. Core/sheath structure with the major component POM as the core and the minor component TPU as the sheath was observed by transmission electron microscopy and further confirmed by surface N contents of the blend fiber mats. The crystalline melting point and the degree of crystallinity of POM have no obvious change by coelectrospinning with TPU due to lack of interaction between POM and TPU as revealed by Fourier transform infrared spectroscopy. Tensile tests showed that the unusual high ductility of POM fiber mat could be further increased by coelectrospinning with 10 or 20 wt % TPU without significantly decreasing the stiffness and strength. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1853–1859, 2009     

Study on morphology of electrospun poly(vinyl alcohol) mats

Submicron poly(vinyl alcohol) (PVA) fiber mats were prepared by electrospinning of aqueous PVA solutions in 6-8% concentration. Fiber morphology was observed under a scanning electron microscope and effects of instrument parameters including electric voltage, tip-target distance, flow rate and solution parameters such as concentration on the morphology of electrospun PVA fibers were evaluated. Results showed that, when PVA with higher degree of hydrolysis (DH) of 98% was used, tip-target distance exhibited no significant effect on the fiber morphology, however the morphological structure can be slightly changed by changing the solution flow rate. At high voltages above 10 kV, electrospun PVA fibers exhibited a broad diameter distribution. With increasing solution concentration, the morphology was changed from beaded fiber to uniform fiber and the average fiber diameter could be increased from 87 ± 14 nm to 246 ± 50 nm. It was also found that additions of sodium chloride and ethanol had significant effects on the fiber diameter and the morphology of electrospun PVA fibers because of the different solution conductivity, surface tension and viscosity. When the DH value of PVA was increased from 80% to 99%, the morphology electrospun PVA fibers was changed from ribbon-like fibers to uniform fibers and then to beaded fibers. The addition of aspirin and bovine serum albumin also resulted in the appearance of beads.     

Simultaneous formation behaviour of surface structures and molecular alignment by patterned photopolymerisation

ABSTRACT

Highly functional soft materials with fine control of molecular alignment are of great interest for the applications in various fields. However, the current method of molecular alignment still has some challenges. Recently, we have developed a new alignment process based on a concept of scanning wave photopolymerisation (SWaP). When a sample is irradiated with spatially selected light, a polymerisation occurs only in an irradiated region, leading to a molecular motion between the irradiated and unirradiated regions. Such molecular motion generates the alignment of liquid crystal molecules. Moreover, a surface relief structure is formed in the polymer film by the molecular motion. In this study, we simultaneously formed the surface structure and molecular alignment by the patterned photopolymerisation. We compared the degree of molecular alignment with the shape of the created surface structure, and revealed that the degree of molecular alignment was maximized at the boundary of irradiated and unirradiated regions. This method enables one to form both molecular alignment patterning and surface structuring in a single step.     

Long-range alignment of gold nanorods in electrospun polymer nano/microfibers

In this study, a scalable fabrication technique for controlling and maintaining the nanoscale orientation of gold nanorods (GNRs) with long-range macroscale order has been achieved through electrospinning. The volume fraction of GNRs with an average aspect ratio of 3.1 is varied from 0.006 to 0.045 in aqueous poly(ethylene oxide) solutions to generate electrospun fibers possessing different GNR concentrations and measuring 40-3000 nm in diameter. The GNRs within these fibers exhibit excellent alignment with their longitudinal axis parallel to the fiber axis n. According to microscopy analysis, the average deviant angle between the GNR axis and n increases modestly from 3.8 to 13.3° as the fiber diameter increases. Complementary electron diffraction measurements confirm preferred orientation of the {100} GNR planes. Optical absorbance spectroscopy measurements reveal that the longitudinal surface plasmon resonance bands of the aligned GNRs depend on the polarization angle and that maximum extinction occurs when the polarization is parallel to n.     

Electrospun fiber mats of poly(3‐hydroxybutyrate), poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate), and their blends

Electrospinning of poly(3‐hydroxybutyrate) (PHB), poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (PHBV), and their blends was first carried out in chloroform at 50 °C on a stationary collector. The average diameter of the as‐spun fiber from PHB and PHBV solutions decreased with increasing collection distance and increased with increasing solution concentration and applied electrical potential. In all of the spinning conditions investigated, the average diameter of the as‐spun pure fibers ranged between 1.6 and 8.8 μm. Electrospinning of PHB, PHBV, and their blends was carried out further at a fixed solution concentration of 14% w/v on a homemade rotating cylindrical collector. Well‐aligned, cross‐sectionally round fibers without beads were obtained. The average diameter of the as‐spun pure and blend fibers ranged between 2.3 and 4.0 μm. The as‐spun fiber mats appeared to be more hydrophobic than the corresponding films and much improvement in the tensile strength and the elongation at break was observed for the blend fiber mats over those of the pure fiber ones. Lastly, indirect cytotoxicity evaluation of the as‐spun pure and blend fiber mats with mouse fibroblasts (L929) indicated that these mats posed no threat to the cells. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2923–2933, 2006     

Encasement of metallic cardiovascular stents with endothelial cell‐selective copolyetheresterurethane microfibers

Cardiovascular metallic stents established in clinical application are typically coated by a thin polymeric layer on the stent struts to improve hemocompatibility, whereby often a drug is added to the coating to inhibit neointimal hyperplasia. Besides such thin film coatings recently nano/microfiber coated stents are investigated, whereby the fibrous coating was applied circumferential on stents. Here, we explored whether a thin fibrous encasement of metallic stents with preferentially longitudinal aligned fibers and different local fiber densities can be achieved by electrospinning. An elastic degradable copolyetheresterurethane, which is reported to selectively enhance the adhesion of endothelial cells, while simultaneously rejecting smooth muscle cells, was utilized for stent coating. The fibrous stent encasements were microscopically assessed regarding their single fiber diameters, fiber covered area and fiber alignment at three characteristic stent regions before and after stent expansion. Stent coatings with thicknesses in the range from 30 to 50 µm were achieved via electrospinning with 1,1,1,3,3,3‐hexafluoro‐2‐propanol (HFP)‐based polymer solution, while a mixture of HFP and formic acid as solvent resulted in encasements with a thickness below 5 µm comprising submicron sized single fibers. All polymeric encasements were mechanically stable during expansion, whereby the fibers deposited on the struts remained their position. The observed changes in fiber density and diameter indicated diverse local deformation mechanisms of the microfibers at the different regions between the struts. Based on these results it can be anticipated that the presented fibrous encasement of stents might be a promising alternative to stents with polymeric strut coatings releasing anti‐proliferative drugs. Copyright © 2015 John Wiley & Sons, Ltd.     

高力学强度细菌纤维素气凝胶纤维的连续化制备

气凝胶纤维因其高外表面积和高柔韧性在能量管理系统中具有潜在应用而引起了广泛关注.但是,目前制备的气凝胶纤维力学强度较低,限制了其实际应用.为提高气凝胶纤维力学性能,在始终保持细菌纤维素(BC)纳米纤维处于湿态下,利用NaOH/尿素/硫脲复合溶剂直接低温溶解原生BC,获得透明的BC纺丝原液;通过湿法纺丝制备了BC水凝胶纤维,经过水洗和冷冻干燥后处理,制得BC气凝胶纤维.采用偏光显微镜(POM)、13C核磁共振(13C-NMR)和高级旋转流变仪研究BC在复合溶剂中的溶解过程与状态;利用全反射傅里叶变换红外吸收光谱(ATR-FTIR)、X射线衍射(XRD)和热失重(TG)研究BC溶解前后结构与性能变化;利用场发射扫描电镜(FESEM)、全自动比表面积和孔径分布分析仪、单丝强力仪对获得的BC气凝胶纤维结构与性能进行表征.结果表明,复合溶剂在?15℃条件下可以直接溶解原生湿态BC,最高溶解浓度为3 wt%;采用湿法纺丝制得高度多孔的连续BC气凝胶纤维,比表面积高达192 m^2/g且具有优异的力学性能,断裂强度和杨氏模量高达(9.36±1.68)MPa和(176±17.55)MPa,如0.4 mg BC气凝胶纤维可以支撑高于其本身质量5×10^4倍的重物.     

Effect of Draw Ratio on the Morphologies and Properties of BPDA/PMDA/ODA Polyimide Fibers

3,3,4,4-Biphenyltetracarboxylic dianhydride/pyromellitic dianhydride/4,4-oxydianiline（BPDA/PMDA/ODA） polyimide copolymer fibers with different draw ratios were prepared from the imidization of polyacrylic acid（PAA） fibers via a dry-jet wet-spinning process.Their morphologies,microcrystal orientations,thermal stabilities,and mechanical properties were investigated via scanning electron microscopy（SEM）,wide angle X-ray diffraction（WAXD）,thermogravimetric analysis（TGA）,and tensile experiments.In order to acquire fibers with better mechanical performance,we aimed at obtaining the optimal draw ratio.Drawing during thermal imidization resulted in a decreased diameter of fiber from 25.8 μm to 16.9 μm corresponding to draw ratio from 1 to 3.5.WAXD results show that the degree of the orientation of the undrawn sample is 64.1％,whereas that of the drawn sample is up to 82％.The as-spun fiber and those with different draw ratios all exhibit high thermal stabilities,i.e.,the temperature at a mass loss of 5％ can reach as high as 570 ℃.The tensile strengths and tensile modulus of the fibers increase with the draw ratios,and the maximum tensile strength and modulus are 0.90 and 12.61 GPa,respectively.     

Controlling electrospun nanofiber morphology and mechanical properties using humidity

Electrospinning is a fiber spinning technique used to produce nanoscale polymeric fibers with superior interconnectivity and specific surface area. The fiber diameter, surface morphology, and mechanical strength are important properties of electrospun fibers that can be tuned for diverse applications. In this study, the authors investigate how the humidity during electrospinning influences these specific properties of the fiber mat. Using two previously uninvestigated polymers, poly(acrylonitrile) (PAN) and polysulfone (PSU) dissolved in N,N‐Dimethylformamide (DMF), experimental results show that increasing humidity during spinning causes an increase in fiber diameter and a decrease in mechanical strength. Moreover, surface features such as roughness or pores become evident when electrospinning in an atmosphere with high relative humidity (RH). However, PAN and PSU fibers are affected differently. PAN has a narrower distribution of fiber diameter regardless of the RH, whereas PSU has a wider and more bimodal distribution under high RH. In addition, PSU fibers spun at high humidity exhibit surface pores and higher specific surface area whereas PAN fibers exhibit an increased surface roughness but no visible pores. These fiber morphologies are caused by a complex interaction between the nonsolvent (water), the hygroscopic solvent (DMF), and the polymer. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Polyaniline/poly(methyl methacrylate) coaxial fibers: The fabrication and effects of the solution properties on the morphology of electrospun core fibers

Electrically conductive polyaniline (PANi)/poly(methyl methacrylate) (PMMA) coaxial fibers were prepared through the chemical deposition of PANi onto preformed PMMA fibers via in situ polymerization. PMMA fibers were prepared as core materials via electrospinning. Spectral studies and scanning electron microscopy observations indicated the formation of PANi/PMMA coaxial fibers with a diameter of approximately 290 nm and a PANi layer thickness of approximately 30 nm. The conductivity of the PANi/PMMA coaxial fibers was significantly higher than that of electrospun fibers of PANi/poly(ethylene oxide) blends and blend cast films of the same PANi composition. To reproducibly generate uniform‐core polymer fibers, the organic solution properties that affected the morphology and diameter of the electrospun fibers were investigated. The polymer molecular weight, solution concentration, solvent dielectric constant, and addition of soluble organic salts were strongly correlated to the morphology of the electrospun fiber mat. In particular, the dielectric constants of the solvents substantially influenced both the fiber diameter and bead formation. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3934–3942, 2004     

Influence of a mixing solvent with tetrahydrofuran and N,N‐dimethylformamide on electrospun poly(vinyl chloride) nonwoven mats

We evaluated the effects of the solvent composition with respect to the solution concentration, applied electric field, and tip‐to‐collector distance on the morphology of electrospun poly(vinyl chloride) (PVC) fibers. The solvent volume ratio was strongly correlated with the diameter of the electrospun fibers with respect to the other processing parameters. Electrospun PVC fibers dissolved in tetrahydrofuran (THF) had diameters ranging from 500 nm to 6 μm; those dissolved in N,N‐dimethylformamide (DMF) had an average diameter of 200 nm. The diameters of the electrospun fibers were obtained from narrow to broad distributions with the solvent composition. Also, the diameters of fibers electrospun from a mixed solvent of THF and DMF were less than 1 μm. The mechanical properties of electrospun PVC nonwoven mats depended on the fiber orientation and linear velocity of the drum surface. With increasing linear velocity of the drum surface, electrospun PVC fibers were arranged toward the machine direction, and the dimensions of the spiral path were shorter. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2259–2268, 2002     

Free surface electrospinning of fibers containing microparticles

Many materials have been fabricated using electrospinning, including pharmaceutical formulations, superhydrophobic surfaces, catalysis supports, filters, and tissue engineering scaffolds. Often these materials can benefit from microparticles included within the electrospun fibers. In this work, we evaluate a high-throughput free surface electrospinning technique to prepare fibers containing microparticles. We investigate the spinnability of polyvinylpyrrolidone (PVP) solutions containing suspended polystyrene (PS) beads of 1, 3, 5, and 10 μm diameter in order to better understand free surface electrospinning of particle suspensions. PS bead suspensions with both 55 kDa PVP and 1.3 MDa PVP were spinnable at 1:10, 1:5, and 1:2 PS:PVP mass loadings for all particle sizes studied. The final average fiber diameters ranged from 0.47 to 1.2 μm and were independent of the particle size and particle loading, indicating that the fiber diameter can be smaller than the particles entrained and can furthermore be adjusted based on solution properties and electrospinning parameters, as is the case for electrospinning of solutions without particles.     

Polarized emission of individual self-assembled oligo(p-phenylenevinylene)-based nanofibers on a solid support

We have prepared 5 nm diameter, micrometer long tetra(p-phenylenevinylene) (OPV)-based nanofibers on a graphite surface. The fluorescence emission of an individual fiber shows a profound polarization over its entire length that directly corresponds to its orientation on the substrate. Quantitative analysis of the fluorescence polarization, including the depolarizing effect of the underlying graphite, evidences the high degree of organization within chiral fibers with the OPV molecules perpendicular to the fiber axis. The control of the internal order within self-assembled fibers, and the ability to measure it, is a crucial step to obtain uniform organic fibers that can be applied in nanosized electronics at room temperature.     

Melt-electrospinning of PMMA

<正>The melt electrospinning of PMMA was investigated.The averaged fiber diameter thus obtained was reduced from 34.0μm to 19.7μm by adding di-(2-ethylhexyl)phthalate to reduce viscosity of the molten PMMA,and it further lowered down to 4.0μm when a KCl/ice-water solution was used as collection media.A comparison study on the PMMA fibers made through melt electrospinning and done by solution electrospinning was made.It was found that solution electrospinning was capable of fabricating very thin fibers as small as to a nanometer size,but resulted in a much wider fiber diameter range than melt-electrospinning did.In general,within some extent an increase in applied voltage and amount of the additive or a decrease in collection distance can give rise to a decreased fiber diameter and improved mechanical performance for the PMMA fibers by melt electrospinning.It was also indicated that the mechanical properties of the PMMA fibers made through melt-electrospinning were superior to those by solution elctropspinning.     

The morphology and crystalline region distribution of polyacrylonitrile nanofibers prepared by electrospinning

The effects of electrospinning parameters in a wider range on the morphology and diameters of polyacrylonitrile (PAN) fibers are studied in detail. The fibers’ diameter increases from 288 to 3469 nm swiftly with the increasing PAN concentration. With the increasing voltage or prolonging gap distance, the diameter increases primarily and decreases later. The combined effects of surface tension, splitting and stretching, electric force, viscosity, and solvent volatilization are the main reasons. Ultrasonic etching method, Atomic force microscope (AFM), Scanning electron microscope (SEM) and X-ray diffraction (XRD) technology have been utilized to verify the nature structure of electrospun PAN fibers. Combining all the results, it is deduced that there are many grooves arranging nearly perpendicular to the fiber axis on the surface of electrospun PAN fibers. The thickness of relative ordered region is 40 to 190 nm and the thickness of amorphous region is 20 to 35 nm.     

Curcumin-Loaded Biodegradable Electrospun Fibers: Preparation,Characterization, and Differences in Fiber Morphology

This article relates curcumin incorporation into poly(latic acid) and poly(lactic-co-glycolic acid) fibers by electrospinning. The fibers were characterized by field emission scanning electron microscopy and Fourier transform-infrared spectroscopy, performed in attenuated total reflection, and the actual curcumin content was evaluated by electronic absorption spectroscopy. The poly(latic acid)/curcumin fibers were malleable, had rough surface, and an average diameter of 3.6 µm. On the other hand, poly(lactic-co-glycolic acid)/curcumin fibers were rigid and porous and had an average diameter of 123.6 nm. The bigger diameter of the poly(latic acid) fibers was responsible for a higher percentage of curcumin/milligram of fiber.     

Poly(methyl methacrylate)/silica nanocomposite fibers by electrospinning

Uniform poly(methyl methacrylate) (PMMA)/silica nanocomposite fibers containing up to 20 wt % silica were prepared by electrospinning. The electrospun solutions were prepared by mixing a solution of PMMA in dimethyl formamide (DMF) with colloidal silica in methyl ethyl ketone (MEK). The average fiber diameter decreases from 2.49 μm to 1.69 μm when 20 wt % silica is incorporated as a result of considerably increased solution conductivity, although the solution viscosity increases significantly, which should result in opposite effect. Thinner fibers (down to 350 nm) can be obtained by changing DMF/MEK proportion and by the addition of an ammonium salt. Nano‐sized silica particles (10–40 nm) distributes homogeneously in the fibers, as revealed by transmission electron microscopy. Furthermore, the incorporation of silica nanoparticles can change the thermal properties and surface wettability of the fiber mats. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1211–1218, 2009     

单根聚己内酯电纺亚微米纤维的动力学特性分析

通过静电纤维制造技术得到直径范围在100～500nm的PCL亚微米纤维,并使用信号发生器和压电片联用对收集到的单根纤维进行振动实验,由共振频率数据得到单根纤维的弹性模量,并同时对直径的测量方法进行了修正.实验结果显示,PCL亚微米纤维的弹性模量随直径变化而显著增加,存在明显的尺寸效应.通过引入应变梯度的振动模型对实验中观测到的尺寸效应进行了理论解释,等效弹性模量的理论预测值与实验数据吻合良好.     

Effect of Terminal Modification on the Molecular Assembly and Mechanical Properties of Protein‐Based Block Copolymers

Accurate prediction and validation of the assembly of bioinspired peptide sequences into fibers with defined mechanical characteristics would aid significantly in designing and creating materials with desired properties. This process may also be utilized to provide insight into how the molecular architecture of many natural protein fibers is assembled. In this work, computational modeling and experimentation are used in tandem to determine how peptide terminal modification affects a fiber‐forming core domain. Modeling shows that increased terminal molecular weight and hydrophilicity improve peptide chain alignment under shearing conditions and promote consolidation of semicrystalline domains. Mechanical analysis shows acute improvements to strength and elasticity, but significantly reduced extensibility and overall toughness. These results highlight an important entropic function that terminal domains of fiber‐forming peptides exhibit as chain alignment promoters, which ultimately has notable consequences on the mechanical behavior of the final fiber products.