Viscoelastic properties of silica‐grafted poly(styrene–acrylonitrile) nanocomposites

The melt state viscoelastic properties of styrene–acrylonitrile random copolymers grafted to silica nanoparticles and prepared by in situ atom transfer radical polymerization are examined. Linear dynamic oscillatory viscoelastic measurements indicate that nanocomposites with silica contents as low as 1.2 vol % exhibit solid‐like response. Steady shear results in considerable alteration to the mesoscale structure and results in the failure of the Cox‐Merz rule. Flow reversal studies confirm the elastic nature of the mesoscale structure and demonstrate that the relaxation of the flow altered structure is slow, non‐Brownian, and possibly cooperative. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2014–2023, 2006     

Influence of chemical composition and sequence length on the transport properties of proton exchange membranes

One of the integral parts of the fuel cell is the proton exchange membrane. Our research group has been engaged in the past few years in the synthesis of several sulfonated poly(arylene ether) random copolymers. The copolymers were varied in both the bisphenol structure as well as in the functional groups in the backbone such as sulfone and ketones. To compare the effect of sequence length, multiblock copolymers based on poly(arylene ether sulfone)s were synthesized. This paper aims to describe our investigation of the effect of chemical composition, morphology, and ion exchange capacity (IEC) on the transport properties of proton conducting membranes. The key properties examined were proton conductivity, methanol permeability, and water self diffusion coefficient in the membranes. It was observed that under fully hydrated conditions, proton conductivity for both random and block copolymers was a function of IEC and water uptake. However, under partially hydrated conditions, the block copolymers showed improved proton conductivity over the random copolymers. The proton conductivity for the block copolymer series was found to increase with increasing block lengths under partially hydrated conditions. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2226–2239, 2006     

Nanostructured hybrid polymer networks from in situ self‐assembly of RAFT‐synthesized POSS‐based block copolymers

A series of well‐defined hybrid block copolymers PMACyPOSS‐b‐PMMA and PMAiBuPOSS‐b‐PMMA exhibiting high POSS weight contents have been synthesized by RAFT polymerization and further studied as modifiers for epoxy thermosets based on diglycidyl ether of bisphenol A. The hybrid block copolymers self‐assembled within the epoxy precursors into micelles possessing an inorganic core and a PMMA corona. Thanks to the presence of the PMMA blocks that remain miscible until the end of the reaction, curing of the resulting blends afforded nanostructured hybrid organic/inorganic networks with well‐dispersed inorganic‐rich nanodomains with diameters on the order of 20 nm. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Poly(styrene-block-isoprene) nanocomposites: Kinetics of intercalation and effects of copolymer on intercalation behaviors

In addition to phase morphology, diffusion, and dynamics in the bulk, the behavior of block copolymers in the confined state has been of great interest. Although random and graft copolymers have been used in polymer-layered silicate nanocomposites, well-defined block copolymers have received relatively little attention. In this study, the kinetics of intercalation of a series of poly(styrene-b-isoprene) block copolymers into a layered silicate were examined via X-ray diffraction. Intercalation was observed even when the copolymer was in the ordered state, with no discontinuity around the order–disorder transition of the copolymer. As the size of the polystyrene block was increased, slower intercalation kinetics were observed, possibly because of the increased glass-transition temperature of the polystyrene segment. Finally, the clearing temperature of the copolymer in the nanocomposites as measured by small-angle X-ray scattering showed a large heating-rate dependence suggesting that the nanoparticles act as kinetics barriers to the disordering of the copolymer. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 3264–3271, 2003     

Synthesis and characterization of new poly(ethyleneimine)‐g‐poly(methyl methacrylate) star‐block copolymers with hyperbranched cationic core

Hyperbranched polyethyleneimine (hb‐PEI) is used as polymeric scaffold to synthesize new PEI‐g‐polymethylmethacrylate (PEI‐g‐PMMA) block copolymers, consisting of a hyperbranched, partially quarternized cationic core, and PMMA‐arms. The arms are grafted to the PEI scaffold by means of the “grafting to” method. Ammonium groups, covalently bond to the hyperbranched core, provide good adhesion to negatively charged surfaces, even in case of low‐surface charges. The PMMA strands provide compatibility of the macromolecules to PMMA matrices, hence generating potential dispersants, and compatibilizers for PMMA. A peculiar association behavior in organic solution is observed as supported by dynamic light scattering and DOSY measurements. First evidences of the applicability of the macromolecules as dispersants to prepare PMMA‐nanocomposites are given. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 3700–3715     

Influence of sample preparation and processing on observed glass transition temperatures of polymer nanocomposites

Polymer composites composed of poly(methyl methacrylate) (PMMA) and silica (14 nm diameter) have been investigated. The influences of sample preparation and processing have been probed. Two types of sample preparation methods were investigated: (i) solution mixture of PMMA and silica in methyl ethyl ketone and (ii) in situ synthesis of PMMA in the presence of silica. After removing all solvent or monomer, as confirmed using thermogravimetric analysis, and after compression molding, drops in T_g of 5–15 °C were observed for all composites (2–12% w/w silica) and even pure polymer reference samples. However, after additional annealing for 72 h at 140 °C, all previously observed drops in T_g disappeared, and the intrinsic T_g of bulk, pure PMMA was again observed. This is indicative of nonequilibrium trapped voids being present in the as‐molded samples. Field‐emission scanning electron microscopy was used to show well‐dispersed particles, and dynamic mechanical analysis was used to probe the mechanical properties (i.e., storage modulus) of the fully equilibrated composites. Even though no equilibrium T_g changes were observed, the addition of silica to the PMMA matrices was observed to improve the mechanical properties of the glassy polymer host. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2270–2276, 2007     

Toughness enhancements in poly(methyl methacrylate) by addition of oriented multiwall carbon nanotubes

The mechanical properties of multiwall carbon nanotube (MWNT)/poly(methyl methacrylate) (PMMA) nanocomposites were studied as a function of nanotube orientation, length, concentration, and type. Orientation and dispersion were assessed by electron microscopy. A processing parameter study revealed the robust nature of fabricating nanotube/PMMA nanocomposites. An optimal set of extrusion conditions was found for minimizing the aggregate size in single‐wall carbon nanotube (SWNT)/PMMA nanocomposites; this set was also used for the fabrication of the MWNT/PMMA composites. Good dispersion was achieved for MWNTs in PMMA at 0.1–10 wt % loading levels (with the best dispersions at the lower loading levels). The orientation of MWNTs in PMMA proved to be the only way to substantially toughen the nanocomposite. A level of 1 wt % MWNTs in PMMA (oriented nanocomposite) exhibited the largest increase in tensile toughness with a 170% improvement over oriented PMMA. Increases in the modulus and yield strength were not nearly as pronounced (and occurred only at the highest loading of MWNTs, which was 10 wt %) with increases of 38 and 25%, respectively. A failure mechanism was proposed in which orientation of the MWNTs (normal to the direction of craze propagation and crack development) enabled them to toughen the brittle PMMA by bridging cracks that developed (via craze precursors) during the tensile test. None of the nanotube/PMMA composites showed mechanical properties close to the values expected from simple rule of mixture and orientation considerations. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2690–2702, 2004     

Thermal‐initiating potentialities of poly(methyl methacrylate) peroxide: Metamorphosis of block‐into‐block copolymer and comparative studies on surface texture and morphology

This is the first report concerning the use of vinyl polyperoxide, namely, poly(methyl methacrylate) peroxide (PMMAP), as a thermal initiator for the synthesis of active polymer PMMAP‐PS‐PMMAP by free‐radical polymerization with styrene. The polymerizations have been carried out at different concentrations of macroinitiator PMMAP. The active polymers have been characterized by ¹H NMR, DSC, thermogravimetric analysis, and gel permeation chromatography. PMMAP‐PS‐PMMAP is further used as the thermal macroinitiator for the preparation of another block copolymer, PMMA‐b‐PS‐b‐PMMA, by reacting the active polymers with methyl methacrylate. The block copolymers have been synthesized by varying the concentrations of the active polymers. The mechanism of block copolymers has been discussed, which is also supported by thermochemical calculations. Studies on the surface texture and morphology of the block copolymer of polystyrene (PS) and PMMA material have been carried out using scanning electron microscopy. Furthermore, in this article, a blend of the same constituent materials (PS and PMMA) in proportions (v/v) similar to that contained in block copolymers has been formulated, and the morphology and surface textures of these materials were also investigated. A comparative microscopical evaluation between two processing methods was done for a better understanding of the processing route dependence of the microstructures. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 546–554, 2001     

Understanding the role of nanosilica particle surfaces in the thermal degradation of nanosilica-poly(methyl methacrylate) solution-blended nanocomposites: From low to high silica concentration

Nanocomposites of poly(methyl methacrylate) and 12 nm silica particles have been prepared by a casting procedure which allows the homogeneous dispersion of up to 35 wt% of silica. Twelve nanocomposites with compositions ranging from 1 to 35 wt% have been prepared and studied by Scanning Electron Microscopy, Fourier Transform Infrared Spectroscopy, Differential Scanning Calorimetry, Thermogravimetric Analysis and Isothermal Chemiluminescence. Thermal stability increases outstandingly as soon as 1 wt% of silica is added to PMMA. This effect is well-known but had not been explained up to now. Of the two main processes which initiate degradation in PMMA, radical formation at labile chain ends and random chain scission, it is the former which disappears in composites with 3 wt% of silica. The origin of the thermal stabilization in these polymer composites is thus the blocking of the PMMA chain end by the silica particle. At the same time, viscous flow decreases progressively, and composites with 20 wt% of silica or over are dimensionally stable even if heated at 300 °C for several hours. The concomitant decrease of viscous flow and increase of low temperature thermal stability shift the temperature range of application of these composites strongly, and the understanding of the silica surface role allows envisaging the control of the behaviour.     

Effects of incorporation of modified silica nanoparticles on the mechanical and thermal properties of PMMA

Silica nanoparticles of various sizes have been incorporated by melt compounding in a poly(methyl methacrylate) (PMMA) matrix to enhance its thermal and mechanical properties. In order to improve nanoparticles dispersion, PMMA grafted particles have been prepared by atom transfer radical polymerization (ATRP) from well-defined silica nanoparticles. This strategy was expected to ensure compatibility between both components of the PMMA nanocomposites. TEM analysis have been performed to evaluate the nanosilica dispersion whereas modified and non-modified silica/PMMA nanocomposites thermal stability and mechanical properties have been investigated by both thermogravimetric and dynamical mechanical analysis.     

Solubilizing single‐walled carbon nanotubes with pyrene‐functionalized block copolymers

The effect of pyrene distribution within pyrene‐functionalized random and block copolymers on noncovalent polymer/single‐walled carbon nanotube (SWNT) interactions was investigated. The block copolymers served as superior solubilizing agents in comparison with the random copolymers. Also, increasing the pyrene content within a polymer, while a constant molecular weight was maintained, improved SWNT solubility and therefore had to result in stronger polymer–nanotube interactions. However, increasing the length of the pyrene‐containing block diminished nanotube solubility, likely because of a lower number of polymer chains that were capable of binding to the nanotube surface. Atomic force microscopy and transmission electron microscopy indicated that the polymer–SWNT interactions were capable of partially debundling the nanotubes into individual solvated structures. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1941–1951, 2006     

Selective control over the lamellar thickness of one domain in thin binary blends of block copolymer films

Thin binary blends of poly(styrene‐b‐methyl methacrylate) (PS‐PMMA) block copolymers in films where the lamellar thickness of one domain is controlled while preserving the thickness of the other domain were demonstrated without microphase separation. One of the block copolymers used here was short and symmetric, and the other was long and asymmetric; the molecular weights of the PMMA block chains in the constituents were similar. A random copolymer brush was introduced and film thickness and composition of brush were adjusted to induce perpendicular orientation in thin film. As the blend composition of the long asymmetric block copolymer increased, the PS lamellar thickness increased from 15.8 to 25.1 nm, whereas the PMMA lamellar thickness remained constant at approximately 14 nm (the thickness decreased slightly from 14.0 to 13.3 nm). The domain spacing behavior in thin film was consistent in the bulk. These results were compared with the Birshtein, Zhulina, and Lyatskaya model and the theories for pure block copolymers in the strong segregation limit and in the intermediate segregation regime. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2013, 51, 1393–1399     

Effects of clay‐modifying agents on the morphology and properties of poly(methyl methacrylate)/clay nanocomposites synthesized via γ‐ray irradiation polymerization

Via γ‐ray irradiation polymerization, poly(methyl methacrylate) (PMMA)/clay nanocomposites were successfully prepared with reactive modified clay and nonreactive clay. With reactive modified clay, exfoliated PMMA/clay nanocomposites were obtained, and with nonreactive clay, intercalated PMMA/clay nanocomposites were obtained. Both results were confirmed by X‐ray diffraction and high‐resolution transmission electron microscopy. PMMA extracted from PMMA/clay nanocomposites synthesized by γ‐ray irradiation had higher molecular weights and narrow molecular weight distributions. The enhanced thermal properties of the PMMA/clay nanocomposites were characterized by thermogravimetric analysis and differential scanning calorimetry. The improved mechanical properties of PMMA/clay were characterized by dynamic mechanical analysis. In particular, the enhancement of the thermal properties of the PMMA/clay nanocomposites with reactive modified clay was much more obvious than that of the PMMA/clay nanocomposites with nonreactive clay. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3218–3226, 2003     

Influence of molecular architecture of S–S/B–S triblock copolymers on rheological properties

The influence of middle and outer block composition of symmetric triblock copolymers consisting of a polystyrene–polybutadiene (S/B) random middle block and two polystyrene (PS) outer blocks on morphology and rheological behavior has been investigated. Master curves are obtained by shifting the experimental data measured at different temperatures using time‐temperature superposition principle, the validity of which was confirmed in the linear viscoelastic regime. The rheological properties are observed to be strongly influenced by the relative composition of the S‐SB‐S triblock copolymers. Increasing the S/B ratio from 1:1 to 1:2 in the middle block has lead to a change in morphology from wormlike to lamellar, which is also accompanied with broad and sharp tan δ peaks in the dynamic mechanical measurements, respectively. The storage and loss modulus have been observed to increase with the increase in PS contents in the outer blocks and PB content in the middle block. The triblock copolymer with wormlike structure showed terminal linear viscoelastic behavior, whereas the ones with lamellar morphology showed nonterminal flow behavior in the similar low‐frequency regime. The relaxation modulus (G_t) has been observed to increase four times when the S/B ratio is increased from 1:1 to 1:2, whereas it increases threefold when the PS‐content in the outer block was increased by just 8 wt %. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2776–2788, 2006     

Role of adsorbed chain rigidity in reinforcement of polymer nanocomposites

The thermomechanical behavior of polymer nanocomposites is mostly governed by interfacial properties which rely on particle–polymer interactions, particle loading, and dispersion state. We recently showed that poly(methyl methacrylate) (PMMA) adsorbed nanoparticles in poly(ethylene oxide) (PEO) matrices displayed an unusual thermal stiffening response. The molecular origin of this unique stiffening behavior resulted from the enhanced PEO mobility within glassy PMMA chains adsorbed on nanoparticles. In addition, dynamic asymmetry and chemical heterogeneities existing in the interfacial layers around particles were shown to improve the reinforcement of composites as a result of good interchain mixing. Here, the role of chain rigidity in this interfacially controlled reinforcement in PEO composites is investigated. We show that particles adsorbed with less rigid polymers improve the mechanical properties of composites. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 9–14     

Functionalized SWNT/polymer nanocomposites for dramatic property improvement

In this paper, we present results for polymer nanocomposites of poly‐ (methyl methacrylate) (PMMA) and amide‐functionalized SWNTs. The results demonstrate that even at very low loadings, 1 wt % (0.5 vol %), the mechanical and electrical properties are significantly improved. The improvement over PMMA properties exceeds the theoretical bounds for composites with the same volume fraction loading of randomly oriented, straight, individually dispersed nanotubes. The modeling and experimental results thus suggest that the nanotube bundles are well dispersed in the polymer matrix, that the functionalization significantly improves interaction with polymer, and that the interphase formed has improved mechanical properties over that of the matrix material. Loss modulus results indicate a significant difference between functionalized and nonfunctionalized tubes in the composite. Functionalized tubes result in a composite in which relaxation mechanisms are shifted by 30 °C from that of the matrix material, indicating extensive interphase regions and absence of PMMA with bulk properties. Unfunctionalized composites demonstrate a broadening of relaxation modes, but still retain the signature of bulk PMMA properties. These data suggest a morphological difference with a discrete interphase layer in unfunctionalized composites and a fully transformed matrix in the case of functionalization. This difference is consistent with electrical and mechanical property data. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2269–2279, 2005     

Novel polymers based on atom transfer radical polymerization of 2‐methoxyethyl acrylate

Atom transfer radical polymerization (ATRP) has been employed in the polymerization of 2‐methoxyethyl acrylate (MEA) initiated by ethyl 2‐bromoisobutyrate in bulk or in toluene solution at 90–95 °C with the catalytic systems Cu(I)Br/PMDETA or HMTETA. Kinetics investigations revealed that ATRP of MEA proceeds in a controlled manner with a first‐order plot of monomer consumption, an almost linear molecular weight evolution and polydispersities < 1.29 in the entire conversion range. Well‐defined diblock copolymers with PMMA, PMEA‐b‐PMMA have been produced by use of both PMEA and PMMA macroinitiators, however, for the latter the controlled conditions were somehow difficult to maintain. The amphiphilic behavior of the diblock copolymers lead to phase separation resulting in two glass transition temperatures as detected by DSC. Contact angle (Θ) investigations with water on PMEA, PMMA, and diblock copolymers surfaces reveal PMEA as an intermediate hydrophilic with Θ ～ 50°, whereas PMMA and the diblock copolymers all fall in the hydrophobic region with Θ > 70°. © 2006 Wiley Periodicals, Inc. J Polym Sci Part Polym Chem45: 333–340, 2007     

Synthesis of block copolymers by combined ultrasonic irradiation and reverse atom transfer radical polymerization processes

A two-step procedure based on ultrasonic irradiation and reverse atom transfer radical polymerization (RATRP) for the synthesis of block copolymers is described. In the first step of the procedure, a stable chlorine-end-capped polymer is formed upon the ultrasonic irradiation of poly(methyl methacrylate) (PMMA) in dry benzene in the presence of a copper chloride/2,2′-bipyridine catalyst. Heating the system to 110 °C initiates the polymerization of the second monomer, styrene, and this results in the formation of the block copolymers. The degradation behavior of PMMA under ultrasonic irradiation has also been studied. The agreement of the experimentally obtained molecular weights and theoretical molecular weights and the unimodal shapes of the gel permeation chromatography curves of the block copolymers indicate the controlled nature of the RATRP process initiated by polymeric radicals formed by sonication. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 534–540, 2004     

SYNTHESIS OF POLY(METHYL METHACRYLATE)-SILICA NANO-COMPOSITES. II. POLY[METHYL METHACRYLATE-block-(METHYL METHACRYLATE-co-2-HYDROXYETHYL METHACRYLATE)]

ABSTRACT

One kind of poly(methyl methacrylate [MMA]-block-2-hydroxyethyl methacrylate [HEMA]) block copolymer and two kinds of poly[MMA1-block-(MMA-co-HEMA)] block-random copolymers were synthesized by atom transfer radical polymerization. Then, poly(methyl methacrylate) [PMMA]-silica nano composites were synthesized by blending perhydropolysilazane (PHPS: NN-110) and block or block-random copolymers in 1,4-dioxane and casting the blend solutions. All composite films were transparent. Silica and organic domains were microphase separated in the composites. The effects of PHEMA content and blend ratio of PHPS to hydroxyl group on the microphase separation were investigated by transmission electron microscopy (TEM) and scanning electron microscopy (SEM). The thermal properties of the composites were investigated by differential scanning calorimetry (DSC) and thermal gravitic analysis (TGA).     

Synthesis and morphology of polyethylene‐block‐poly(methyl methacrylate) through the combination of metallocene catalysis with living radical polymerization

Polyethylene‐block‐poly(methyl methacrylate) (PE‐b‐PMMA) was successfully synthesized through the combination of metallocene catalysis with living radical polymerization. Terminally hydroxylated polyethylene, prepared by ethylene/allyl alcohol copolymerization with a specific zirconium metallocene/methylaluminoxane/triethylaluminum catalyst system, was treated with 2‐bromoisobutyryl bromide to produce terminally esterified polyethylene (PE‐Br). With the resulting PE‐Br as an initiator for transition‐metal‐mediated living radical polymerization, methyl methacrylate polymerization was subsequently performed with CuBr or RuCl₂(PPh₃)₃ as a catalyst. Then, PE‐b‐PMMA block copolymers of different poly(methyl methacrylate) (PMMA) contents were prepared. Transmission electron microscopy of the obtained block copolymers revealed unique morphological features that depended on the content of the PMMA segment. The block copolymer possessing 75 wt % PMMA contained 50–100‐nm spherical polyethylene lamellae uniformly dispersed in the PMMA matrix. Moreover, the PE‐b‐PMMA block copolymers effectively compatibilized homopolyethylene and homo‐PMMA at a nanometer level. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3965–3973, 2003