Kinetic study of the nitroxide‐mediated controlled free‐radical polymerization of n‐butyl acrylate in aqueous miniemulsions

The controlled free‐radical homopolymerization of n‐butyl acrylate was studied in aqueous miniemulsions at 112 and 125 °C with a low molar mass alkoxyamine unimolecular initiator and an acyclic β‐phosphonylated nitroxide mediator, N‐tert‐butyl‐N‐(1‐diethylphosphono‐2,2‐dimethylpropyl) nitroxide, also called SG1. The polymerizations led to stable latices with 20 wt % solids and were obtained with neither coagulation during synthesis nor destabilization over time. However, in contrast to latices obtained via classical free‐radical polymerization, the average particle size of the final latices was large, with broad particle size distributions. The initial [SG1]₀/[alkoxyamine]₀ molar ratio was shown to control the rate of polymerization. The fraction of SG1 released upon macroradical self‐termination was small with respect to the initial alkoxyamine concentration, indicating a very low fraction of dead chains. Average molar masses were controlled by the initial concentration of alkoxyamine and increased linearly with monomer conversion. The molar mass distribution was narrow, depending on the initial concentration of free nitroxide in the system. The initiator efficiency was lower than 1 at 112 °C but was very significantly improved when either a macroinitiator was used at 112 °C or the polymerization temperature was raised to 125 °C. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 4410–4420, 2002     

Proton‐controlled nitroxide mediated radical polymerization of styrene

The pyridyl alkoxyamine, which is composed of the 1‐phenylethyl radical and a pyridyl nitroxide fragments, displays protonation‐controlled C? ON bond homolysis. Its dissociation rate constant k_d value is approximately halved at 100 °C in tert‐butyl benzene when it is protonated by one equivalent of trifluoroacetic acid. Moreover, the bulk polymerization of styrene at 125 °C is performed with a good control over the molecular weight and the dispersity when initiated with this alkoxyamine under its basic and acidic forms but the protonation has induced a strong decreased polymerization rate. In contrast, in the case of n‐butyl acrylate, the control over the polymerization is lost for the protonated pyridyl alkoxyamine because the pyridyl nitroxide is less thermally stable under its acidic form. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Kinetics and electron spin resonance study of the radical polymerization of n‐butyl acrylate mediated by a nitroxide precursor: C‐phenyl‐N‐tert‐butylnitrone

The C‐phenyl‐N‐tert‐butylnitrone/azobisisobutyronitrile pair is able to impart control to the radical polymerization of n‐butyl acrylate as long as a two‐step process is implemented, that is, the prereaction of the nitrone and the initiator in toluene at 85 °C for 4 h followed by the addition and polymerization of n‐butyl acrylate at 110 °C. The structure of the in situ formed nitroxide has been established from kinetic and electron spin resonance data. The key parameters (the dissociation rate constant, combination rate constant, and equilibrium constant) that govern the process have been evaluated. The equilibrium constant between the dormant and active species is close to 1.6 × 10^?12 mol L^?1 at 110 °C. The dissociation rate constant and the activation energy for the C? ON bond homolysis are 1.9 × 10^?3 s^?1 and 122 ± 15 kJ mol^?1, respectively. The rate constant of recombination between the propagating radical and the nitroxide is as high as 1.2 × 10⁹ L mol^?1 s^?1. Finally, well‐defined poly(n‐butyl acrylate)‐b‐polystyrene block copolymers have been successfully prepared. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6299–6311, 2006     

Preparation of polyethylene block copolymers by a combination of postmetallocene catalysis of ethylene polymerization and atom transfer radical polymerization

The synthesis of block copolymers consisting of a polyethylene segment and either a poly(meth)acrylate or polystyrene segment was accomplished through the combination of postmetallocene-mediated ethylene polymerization and subsequent atom transfer radical polymerization. A vinyl-terminated polyethylene (number-average molecular weight = 1800, weight-average molecular weight/number-average molecular weight =1.70) was synthesized by the polymerization of ethylene with a phenoxyimine zirconium complex as a catalyst activated with methylalumoxane (MAO). This polyethylene was efficiently converted into an atom transfer radical polymerization macroinitiator by the addition of α-bromoisobutyric acid to the vinyl chain end, and the polyethylene macroinitiator was used for the atom transfer radical polymerization of n-butyl acrylate, methyl methacrylate, or styrene; this resulted in defined polyethylene-b-poly(n-butyl acrylate), polyethylene-b-poly(methyl methacrylate), and polyethylene-b-polystyrene block copolymers. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 496–504, 2004     

Controlled free radical ring-opening polymerization and chain extension of the “living” polymer

Free radical ring-opening polymerization of 2-methylene-1,3-dioxepane (MDP) in the presence of 2,2,6,6-tetramethyl-1-piperidinyloxy free radical (TEMPO) has been achieved to afford a chain polyester (PMDP) with di-t-butyl peroxide (DTBP) as an initiator at 125°C. The polydispersity of the polymers decreases as the concentration of TEMPO is increased. At high TEMPO concentrations, the polydispersity as low as 1.2 was obtained, which is below the theoretical lower limit for a conventional free radical polymerization. A linear relationship between the number-average molecular weight (M_n) and the monomer conversion was observed with the best-fit line passing very close to the origin of the M_n-conversion plot. The isolated and purified TEMPO-capped PMDP polymers have been employed to prepare chain extended polymers upon addition of more MDP monomer. These results are suggestive of the “living” polymerization process. A possible polymerization mechanism might involve thermal homolysis of the TEMPO-PMDP bonds followed by the addition of the monomers. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 761–771, 1998     

Novel miktofunctional initiator for the preparation of an ABC‐type miktoarm star polymer via a combination of controlled polymerization techniques

An ABC‐type miktoarm star polymer was prepared with a core‐out method via a combination of ring‐opening polymerization (ROP), stable free‐radical polymerization (SFRP), and atom transfer radical polymerization (ATRP). First, ROP of ϵ‐caprolactone was carried out with a miktofunctional initiator, 2‐(2‐bromo‐2‐methyl‐propionyloxymethyl)‐3‐hydroxy‐2‐methyl‐propionic acid 2‐phenyl‐2‐(2,2,6,6‐tetramethyl‐piperidin‐1‐yl oxy)‐ethyl ester, at 110 °C. Second, previously obtained poly(ϵ‐caprolactone) (PCL) was used as a macroinitiator for SFRP of styrene at 125 °C. As a third step, this PCL–polystyrene (PSt) precursor with a bromine functionality in the core was used as a macroinitiator for ATRP of tert‐butyl acrylate in the presence of Cu(I)Br and pentamethyldiethylenetriamine at 100 °C. This produced an ABC‐type miktoarm star polymer [PCL–PSt–poly(tert‐butyl acrylate)] with a controlled molecular weight and a moderate polydispersity (weight‐average molecular weight/number‐average molecular weight < 1.37). The obtained polymers were characterized with gel permeation chromatography and ¹H NMR. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4228–4236, 2004     

Living/controlled copolymerization of acrylates with nonactivated alkenes

The living/controlled copolymerization of methyl acrylate with 1‐alkenes and norbornene derivatives through several radical polymerization techniques has been achieved. These techniques include atom transfer radical polymerization, reversible addition–fragmentation transfer polymerization, nitroxide‐mediated polymerization, and degenerative transfer polymerization. These systems display many of the characteristics of a living polymerization process: the molecular weight increases linearly with the overall conversion, but the polydispersity remains low. Novel block copolymers have been synthesized through the sequential addition of monomers or chain extension. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 6175–6192, 2004     

Stable free radical polymerization of n-butyl acrylate in the presence of high-temperature initiators

Living radical polymerizations of acrylate are known to be difficult to achieve using TEMPO as a mediator. The stable free radical polymerization (SFRP) of acrylate tends to stop at low monomer conversion due to the accumulation of TEMPO in the medium as a result of unavoidable bimolecular termination. Rather than solving this problem by destroying the excess nitroxide using ascorbic acid or glyceraldehyde associated with pyridine as reported recently, high temperature initiators were used to slowly and continuously generate new radicals throughout the polymerization to consume the excess TEMPO molecules. Polymerizations of n-butyl acrylate initiated by the alkoxyamine unimer (1-benzoyloxy)-2-phenyl-2-(2′,2′,6′,6′-tetramethyl-1′-piperidinyloxy)ethane (BST) were performed between 130 °C and 134 °C in the presence of a series of high temperature peroxide and azo initiators. The best results in this study were obtained by the continuous addition of small amounts of di-tert-amyl peroxide throughout the polymerization. Under these conditions, the acrylate polymerizations fulfilled the criteria of a controlled polymerization process although the molecular weight distributions were slightly broad (M_w/M_n ∼ 1.5).     

Ligated anionic block copolymerization of methyl methacrylate with n-butyl acrylate and n-nonyl acrylate as promoted by lithium 2-(2-methoxyethoxy) ethoxide/diphenylmethyllithium

Poly(methyl methacrylate-b-n-butyl acrylate) (PMMA-b-Pn-BuA) and poly(methyl methacrylate-b-n-nonyl acrylate) (PMMA-b-Pn-NonA) diblock copolymers have been successfully synthesized by the sequential anionic polymerization of methyl methacrylate (MMA) and the n-alkyl acrylate (n-BuA or n-NonA), in a 90/10 toluene/tetrahydrofuran (THF) mixture at −78°C. When diphenylmethyllithium (DPMLi) ligated with lithium 2-(2-methoxyethoxy) ethoxide (LiOEEM) is used as the initiator, the polymerization of each block appears to be living. Molecular weight and composition of block copolymers can be predicted from the monomer over initator molar ratio and the molecular weight distribution is narrow. Size exclusion chromatography (SEC) supports that no homo-PMMA contaminates the final copolymer. Although the reverse polymerization sequence Pn-NonA-b-PMMA always results in some contamination by homo-Pn-NonA, it has no really significant effect on the final product characteristics. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 1543–1548, 1997     

Kinetic studies on the n-alkyl acrylate polymerization

Kinetic studies on the polymerization of n-butyl acrylate and n-octadecyl acrylate in toluene at 70°C with benzoyl peroxide as initiator are reported. High monomer orders of 1.55 and 1.75 were obtained for n-butyl and n-octadecyl acrylates, respectively. Though the initiator order in butyl acrylate polymerization was 0.5, the octadecyl acrylate polymerization showed less than square root initiator order. The activation energy for the polymerization of both the acrylates was determined. Autoacceleration was found even at low conversions. The autoacceleration was influenced by both monomer and initiator concentration. Molecular weight data was presented in support of the gel effect. © 1992 John Wiley & Sons, Inc.     

Free radical and nitroxide mediated polymerization of hydroxy–functional acrylates prepared via lipase–catalyzed transacylation reactions

3‐Hydroxypropyl acrylate, 4‐hydroxybutyl acrylate, 2‐methyl‐3‐hydroxypropyl acrylate, 2‐hydroxypropyl acrylate, neopentyl glycol acrylate, glyceryl acrylate, and dihydroxyhexyl acrylate were prepared via transacylation reaction of methyl acrylate with diols and triols catalyzed by Candida antarctica lipase B. After removal of the enzyme by filtration and the methyl acrylate by distillation, the monomers were polymerized via free radical polymerization (FRP) with azobisisobutyronitrile as initiator and nitroxide mediated polymerization (NMP) employing Blocbuilder? alkoxyamine initiator and SG‐1 free nitroxide resulting in hydroxy functional poly(acrylates). The NMP kinetics are discussed in detail. In addition, the polymers obtained by FRP and NMP are compared and the results are related to the amount of bisacrylates that are present in the initial monomer mixtures resulting from the transacylation reactions. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2610–2621, 2010     

Controlled radical polymerization of styrene mediated by the C‐phenyl‐N‐tert‐butylnitrone/AIBN pair: Kinetics and electron spin resonance analysis

Kinetics of the free radical polymerization of styrene at 110 °C has been investigated in the presence of C‐phenyl‐N‐tert‐butylnitrone (PBN) and 2,2′‐azobis(isobutyronitrile) (AIBN) after prereaction in toluene at 85 °C. The effect of the prereaction time and the PBN/AIBN molar ratio on the in situ formation of nitroxides and alkoxyamines (at 85 °C), and ultimately on the control of the styrene polymerization at 110 °C, has been investigated. As a rule, the styrene radical polymerization is controlled, and the mechanism is one of the classical nitroxide‐mediated polymerization. Only one type of nitroxide (low‐molecular‐mass nitroxide) is formed whatever the prereaction conditions at 85 °C, and the equilibrium constant (K) between active and dormant species is 8.7 × 10^?10 mol L^?1 at 110 °C. At this temperature, the dissociation rate constant (k_d) is 3.7 × 10^?3 s^?1, the recombination rate constant (k_c) is 4.3 × 10⁶ L mol^?1 s^?1, whereas the activation energy (E_a,diss.), for the dissociation of the alkoxyamine at the chain‐end is ～125 kJ mol^?1. Importantly, the propagation rate at 110 °C, which does not change significantly with the prereaction time and the PBN/AIBN molar ratio at 85 °C, is higher than that for the thermal polymerization at 110 °C. This propagation rate directly depends on the equilibrium constant K and on the alkoxyamine and nitroxide concentrations, as well. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1219–1235, 2007     

Low‐temperature controlled free‐radical polymerization of vinyl monomers in the presence of a novel cyclic dixanthate under γ‐ray irradiation

The free‐radical polymerization of methyl acrylate (MA) has been studied in the presence of a novel cyclic dixanthate under γ‐ray irradiation (80 Gy min^?1) at room temperature (～28 °C), ?30 °C, and ?76 °C respectively. The resultant polymers have controlled molecular weights and relatively narrow molecular weight distributions, especially at low temperatures (i.e., ?30 and ?76 °C). The polymerization control may be associated with the temperature: the lower the temperature is, the more control there is. Matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry analysis of poly(methyl acrylate) (PMA) samples shows that there are at least three distributions: [3‐(MA)_n‐H]⁺ cyclic polymers, [3‐(MA)_n‐THF‐H]⁺, and [3‐(MA)_n‐(THF)₂‐H]⁺ linear PMAs. The relative content of the cyclic polymers markedly increases at a lower temperature, and this may be related to the reduced diffusion rate and the suppressed chain‐transfer reaction at the low temperature. It is evidenced that the good control of the polymerization at the low temperature may be associated with the suppressed chain‐transfer reaction, unlike reversible addition–fragmentation chain transfer polymerization. In addition, styrene bulk polymerizations have been performed, and gel permeation chromatography traces show that there is only one cyclic dixanthate moiety in the polymer chain. This article is the first to report the influence of a low temperature on controlled free‐radical polymerizations. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2847–2854, 2007     

Synthesis of poly(methyl methacrylate)‐b‐polystyrene containing a crown ether unit at the junction point via combination of atom transfer radical polymerization and nitroxide mediated radical polymerization routes

Poly(methyl methacrylate)‐b‐polystyrene (PMMA‐b‐PS) containing a benzo‐15‐crown‐5 unit at the junction point was prepared by combining atom transfer radical polymerization and nitroxide‐mediated radical polymerization. For this purpose, 6,7,9,10,12,13,15,16‐octahydro‐5,8,11,14,17‐pentaoxa‐benzocyclopentadecene‐2‐carboxylic acid 3‐(2‐bromo‐2‐methyl‐propionyloxy)‐2‐methyl‐2‐[2‐phenyl‐2‐(2,2,6,6‐tetramethyl‐piperidin‐1‐yloxy)‐ethoxycarbonyl]‐propyl ester ( 3 ) was synthesized and used as an initiator in atom transfer radical polymerization of methyl methacrylate in the presence of CuCl and pentamethyldiethylenetriamine at 60°C. A linear behavior was observed in both plots of ln([M]₀/[M]) versus time and M_n,_GPC versus conversion indicating that the polymerization proceeded in a controlled/living manner. Thus obtained PMMA precursor was used as a macroinitiator in nitroxide‐mediated radical polymerization of styrene (St) at 125°C to give well‐defined PMMA‐b‐PS with crown ether per chain. Kinetic data were also obtained for copolymerization. Moreover, potassium picrate (K⁺ picrate) complexation of 3 and PMMA‐b‐PS copolymer was studied. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3242–3249, 2006     

Chain transfer to solvent in the radical polymerization of N‐isopropylacrylamide

Chain transfer to solvent has been investigated in the conventional radical polymerization and nitroxide‐mediated radical polymerization (NMP) of N‐isopropylacrylamide (NIPAM) in N,N‐dimethylformamide (DMF) at 120 °C. The extent of chain transfer to DMF can significantly impact the maximum attainable molecular weight in both systems. Based on a theoretical treatment, it has been shown that the same value of chain transfer to solvent constant, C_tr,S, in DMF at 120 °C (within experimental error) can account for experimental molecular weight data for both conventional radical polymerization and NMP under conditions where chain transfer to solvent is a significant end‐forming event. In NMP (and other controlled/living radical polymerization systems), chain transfer to solvent is manifested as the number‐average molecular weight (M_n) going through a maximum value with increasing monomer conversion. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Nitroxide‐mediated radical polymerization of 2‐(dimethylamino)ethyl acrylate and its sequential block copolymerization with styrene and N‐butyl acrylate

Nitroxide‐mediated radical polymerization (NMRP) of 2‐(dimethylamino)ethyl acrylate (DMAEA) was carried out at 100–120 °C, initiated by MONAMS, an alkoxyamine based on N‐tert‐butyl‐N‐(1‐diethyl phosphono‐2,2‐dimethylpropyl)nitroxide, SG1. Controlled polymerization can be achieved by the addition of free SG1 (the initial molar ratio of SG1 to MONAMS ranged from 0.06 to 0.12), giving a linear first‐order kinetic plot up to 55–70% conversion depending on the reaction conditions. The molecular weights show a near linear increase with conversion; however, they deviate to some extent with theoretical values. SG1‐mediated polymerization of DMAEA at 112 °C is also controlled in organic solvents (N,N‐dimethylformide, anisole, xylene). Polymerization rate increases with increasing solvent polarity. Chain transfer to polymer produces ～1 mol % branches in bulk and 1.2–1.9 mol % in organic solvents, typical of those for acrylates. From poly(styrene) (pS) and poly(n‐butyl acrylate) (pBA) macroinitiators, amphiphilic di‐ and triblock copolymers p(S‐b‐DMAEA), p(DMAEA‐b‐S‐b‐DMAEA), p(BA‐b‐DMAEA), and p(DMAEA‐b‐BA‐b‐DMAEA) were synthesized via NMRP at 110 °C. Polymers were characterized by GPC, NMR, surface tension measurements, and DSC. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 414–426, 2006     

Living free‐radical polymerization of sterically hindered monomers: Improving the understanding of 1,1‐disubstituted monomer systems

The sterically hindered, 1,1‐disubstituted monomers di‐n‐butyl itaconate (DBI), dicyclohexyl itaconate (DCHI), and dimethyl itaconate (DMI) were polymerized with reversible addition–fragmentation chain transfer (RAFT) free‐radical polymerization and atom transfer radical polymerization (ATRP). Cumyl dithiobenzoate, cumyl phenyl dithioacetate, 2‐cyanoprop‐2‐yl dithiobenzoate, 4‐cyanopentanoic acid dithiobenzoate, and S‐methoxycarbonylphenylmethyl dithiobenzoate were employed as RAFT agents to mediate a series of polymerizations at 60 °C yielding polymers ranging in their number‐average molecular weight from 4500 to 60,000 g mol^?1. The RAFT polymerizations of these hindered monomers displayed hybrid living behavior (between conventional and living free‐radical polymerization) of various degrees depending on the molecular structure of the initial RAFT agent. In addition, DCHI was polymerized via ATRP with a CuCl/methyl benzoate/N,N,N′,N″,N″‐pentamethyldiethylenetriamine/cyclohexanone system at 60 °C. Both the ATRP and RAFT polymerization of the hindered monomers displayed living characteristics; however, broader than expected molecular weight distributions were observed for the RAFT systems (polydispersity index = 1.15–3.35). To assess the cause of this broadness, chain‐transfer‐to‐monomer constants for DMI, DBI, and DCHI were determined (1.4 × 10^?3, 1.3 × 10^?3, and 1.0 × 10^?3, respectively) at 60 °C. Simulations carried out with the PREDICI program package suggested that chain transfer to monomer contributed to the broadening process. In addition, the experimental results indicated that viscosity had a pronounced effect on the broadness of the molecular weight distributions. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3692–3710, 2006     

Acrylonitrile‐containing polymers via a combination of metal‐catalyzed living radical and nitroxide‐mediated free‐radical polymerization routes

2‐Phenyl‐2‐[(2,2,6,6‐tetramethylpiperidino)oxy] ethyl 2‐bromopropanoate was successfully used as an initiator in consecutive living radical polymerization routes, such as metal‐catalyzed living radical polymerization and nitroxide‐mediated free‐radical polymerization, to produce various types of acrylonitrile‐containing polymers, such as styrene–acrylonitrile, polystyrene‐b‐styrene–acrylonitrile, polystyrene‐b‐poly(n‐butyl acrylate)‐b‐polyacrylonitrile, and polystyrene‐b‐polyacrylonitrile. The kinetic data were obtained for the metal‐catalyzed living radical polymerization of styrene–acrylonitrile. All the obtained polymers were characterized with ¹H NMR, gel permeation chromatography, and differential scanning calorimetry. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3374–3381, 2006     

Seeded semibatch emulsion polymerization of butyl acrylate: Effect of the chain‐transfer agent on the kinetics and structural properties

The effect of dodecane‐1‐thiol on the kinetics, gel fraction, level of branches, and sol molecular weight distribution of the seeded semibatch emulsion polymerization of n‐butyl acrylate carried out at 75 °C was investigated. The gel fraction was strongly affected by the content of the chain‐transfer agent (CTA). The sol weight‐average molecular weights decreased with increasing CTA concentration, whereas no effect on the kinetics and the level of branches was observed. The experimental data were analyzed with a mathematical model of the process that was able to catch fairly well the effect of the process variable. In addition, adhesive tests were carried out to check the effect of the gel fraction on the adhesive properties. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 1106–1119, 2001     

A styryl tipno‐based nitroxide as efficient mediator for the synthesis of multiblock polystyrenes and well‐grafted polymers

The chloromagnesium exchange of 4‐chlorostyrene provides an easy access to a new versatile polymerizable 2,2,5‐trimethyl‐4‐phenyl‐3‐azahexane‐3‐nitroxide (TIPNO)‐based nitroxide. Indeed, first, its alkoxyamine based on the α‐methyl benzyl radical fragment efficiently mediates the polymerization of styrene (respectively n‐butyl acrylate) to yield branched polystyrene [respectively poly(n‐butyl acrylate)] with alkoxyamine function as branch point and well‐defined branches. Second, the self‐condensing of this polymerizable nitroxide by manganese coupling affords a mixture of oligomeric linear polyalkoxyamines. Polymerization of styrene mediated with these polyalkoxyamines gives multiblock polystyrenes with alkoxyamine group as linker between polystyrene blocks and exhibits the following features: the synthesis of the polystyrene blocks is controlled as their average molecular weight M_n(block) increases linearly with conversion and their average dispersity M_w/M_n(block) decreases with it. At a given temperature, the molecular weight and the dispersity of the polyalkoxyamines weakly impact M_n(block) and M_w/M_n(block). In contrast, the molecular weight of the multiblock polystyrene increases linearly with conversion until reaching a constant value. The number of block is independent of the molecular weight of the polyalkoxyamines. These unusual results can be explained by the fact that during polymerization, mediating TIPNO‐based polymeric nitroxides with different lengths are generated and are exchanged. Finally the dispersity of the multiblock polystyrene is quite broad and lies between 1.7 and 2.8. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012