Multiple melting behavior of poly(butylene succinate). II. Thermal analysis of isothermal crystallization and melting process

The multiple melting behavior of poly(butylene succinate) (PBSu) was studied with differential scanning calorimetry (DSC). Three different PBSu resins, with molecular weights (MWs) of 1.1 × 10⁵, 1.8 × 10⁵, and 2.5 × 10⁵, were isothermally crystallized at various crystallization temperatures (T_c) ranging from 70 to 97.5 °C. The T_c dependence of crystallization half‐time (τ) was obtained. DSC melting curves for the isothermally crystallized samples were obtained at a heating rate of 10 K min⁻¹. Three endothermic peaks, an annealing peak, a low‐temperature peak L, and a high‐temperature peak H, and an exothermic peak located between peaks L and H clearly appeared in the DSC curve. In addition, an endothermic small peak S appeared at a lower temperature of peak H. Peak L increased with increasing T_c, whereas peak H decreased. The T_c dependence of the peak melting temperatures [T_m(L) and T_m(H)], recrystallization temperature (T_re), and heat of fusion (ΔH) was obtained. Their fitting curves were obtained as functions of T_c. T_m(L), T_re, and ΔH increased almost linearly with T_c, whereas T_m(H) was almost constant. The maximum rate of recrystallization occurred immediately after the melting. The mechanism of the multiple melting behavior is explained by the melt‐recrystallization model. The high MW samples showed similar T_c dependence of τ, and τ for the lowest MW sample was longer than that for the others. Peak L increased with MW, whereas peak H decreased. In spite of the difference of MW, T_m(L), T_m(H), and T_re almost coincided with each other at the same T_c. The ΔH values, that is crystallinity, for the highest MW sample were smaller than those for the other samples at the same T_c. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2039–2047, 2005     

Multiple melting behavior of poly(butylene succinate). I. Thermal analysis of melt‐crystallized samples

The multiple melting behavior of poly(butylene succinate) (PBSu) was studied with differential scanning calorimetry (DSC). Three different PBSu resins, with molecular weights of 1.1 × 10⁵, 1.8 × 10⁵, and 2.5 × 10⁵, were cooled from the melt (150 °C) at various cooling rates (CRs) ranging from 0.2 to 50 K min^?1. The peak crystallization temperature (T_c) of the DSC curve in the cooling process decreased almost linearly with the logarithm of the CR. DSC melting curves for the melt‐crystallized samples were obtained at 10 K min^?1. Double endothermic peaks, a high‐temperature peak H and a low‐temperature peak L, and an exothermic peak located between them appeared. Peak L decreased with increasing CR, whereas peak H increased. An endothermic shoulder peak appeared at the lower temperature of peak H. The CR dependence of the peak melting temperatures [T_m(L) and T_m(H)], recrystallization temperature (T_re), and heat of fusion (ΔH) was obtained. Their fitting curves were obtained as functions of log(CR). T_m(L), T_re, and ΔH decreased almost linearly with log(CR), whereas T_m(H) was almost constant. Peak H decreased with the molecular weight, whereas peak L increased. It was suggested that the rate of the recrystallization decreased with the molecular weight. T_m(L), T_m(H), T_re, and T_c for the lowest molecular weight sample were lower than those for the others. In contrast, ΔH for the highest molecular weight sample was lower than that for the others. If the molecular weight dependence of the melting temperature for PBSu is similar to that for polyethylene, the results for the molecular weight dependence of PBSu can be explained. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2411–2420, 2002     

Multiple melting endotherms in isothermally melt-crystallized poly(butylene terephthalate)

The melting behavior of poly(butylene terephthalate) crystallized isothermally for various times was examined using differential scanning calorimetry. After short crystallization times, the DSC analysis gave two melting peaks, but after longer times, the analysis gave three peaks. The latter triplet of DSC peaks can be denoted as low, middle, and high, starting with the lowest temperature endotherm. The DSC peaks were simulated using a measured recrystallization rate and behavior for PBT and an assumed initial melting point distribution. The low and middle peaks represent the original melting peaks arising from isothermal crystallization. The high melting peak arises from recrystallization during the DSC heating scan. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 1757–1767, 1998     

Analysis of the complex thermal behavior of poly(L‐lactic acid) film. I. Samples crystallized from the glassy state

The melting behavior of poly(L ‐lactic acid) film crystallized from the glassy state, either isothermally or nonisothermally, was studied by wide angle X‐ray diffraction (WAXD), small angle X‐ray scattering (SAXS), differential scanning calorimetry (DSC), and temperature‐modulated differential scanning calorimetry (TMDSC). Up to three crystallization and two melting peaks were observed. It was concluded that these effects could largely be accounted for on the basis of a “melt‐recrystallization” mechanism. When molecular weight is low, two melting endotherms are readily observed. But, without TMDSC, the double melting phenomena of high molecular weight PLLA is often masked by an exotherm just prior to the final melting, as metastable crystals undergo melt‐recrystallization during heating in the DSC. The appearance of a double cold‐crystallization peak during the DSC heating scan of amorphous PLLA film is the net effect of cold crystallization and melt‐recrystallization of metastable crystals formed during the initial cold crystallization. Samples cold‐crystallized at 80 and 90 °C did not exhibit a long period, although substantial crystallinity developed. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3200–3214, 2006     

Crystallization measurements via ultrasonic velocity: Study of poly(lactic acid) parts

Crystallization has significant effects on the physical and mechanical properties of polymer products; therefore, crystallization measurements are important for understanding and predicting polymer products' properties. However, traditional crystallization measurement methods have disadvantages in practical applications because they can be destructive, offline, unsafe, and expensive. Recently, ultrasonic technology has shown great potential as a nondestructive, online, real‐time, and environmentally friendly measurement method for polymer characterization. In this study, a novel measurement method based on ultrasonic technology was proposed to study the crystallization characteristics of poly(lactic acid) (PLA) parts. An annealing process was employed to produce PLA parts with different degrees of crystallinity. A new ultrasonic water immersion method was used to measure the ultrasonic velocities of these annealed PLA parts. It has been found that the plot of the inverse ultrasonic velocity versus the degree of crystallinity shows good linearity over the whole crystallinity range for all three annealing temperatures. The linear relationship between the inverse of the ultrasonic velocity and the crystallinity observed in this study could provide a nondestructive method for investigating the degree of crystallinity of polymers, which can be implemented both offline and online. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 700–708     

Temperature‐modulated differential scanning calorimetry studies on the origin of double melting peaks in isothermally melt‐crystallized poly(L‐lactic acid)

In this work, the melting behaviors of nonisothermally and isothermally melt‐crystallized poly(L ‐lactic acid) (PLLA) from the melt were investigated with differential scanning calorimetry (DSC) and temperature‐modulated differential scanning calorimetry (TMDSC). The isothermal melt crystallizations of PLLA at a temperature in the range of 100–110 °C for 120 min or at 110 °C for a time in the range of 10–180 min appeared to exhibit double melting peaks in the DSC heating curves of 10 °C/min. TMDSC analysis revealed that the melting–recrystallization mechanism dominated the formation of the double melting peaks in PLLA samples following melt crystallizations at 110 °C for a shorter time (≤30 min) or at a lower temperature (100, 103, or 105 °C) for 120 min, whereas the double lamellar thickness model dominated the formation of the double melting peaks in those PLLA samples crystallized at a higher temperature (108 or 110 °C) for 120 min or at 110 °C for a longer time (≥45 min). © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 466–474, 2007     

Dynamic mechanical behavior of acrylonitrile butadiene rubber/poly(ethylene‐co‐vinyl acetate) blends

The dynamic mechanical behavior of uncrosslinked (thermoplastic) and crosslinked (thermosetting) acrylonitrile butadiene rubber/poly(ethylene‐co‐vinyl acetate) (NBR/EVA) blends was studied with reference to the effect of blend ratio, crosslinking systems, frequency, and temperature. Different crosslinked systems were prepared using peroxide (DCP), sulfur, and mixed crosslink systems. The glass‐transition behavior of the blends was affected by the blend ratio, the nature of crosslinking, and frequency. sThe damping properties of the blends increased with NBR content. The variations in tan δ_max were in accordance with morphology changes in the blends. From tan δ values of peroxide‐cured NBR, EVA, and blends the crosslinking effect of DCP was more predominant in NBR. The morphology of the uncrosslinked blends was examined using scanning electron and optical microscopes. Cocontinuous morphology was observed between 40 and 60 wt % of NBR. The particle size distribution curve of the blends was also drawn. The Arrhenius relationship was used to calculate the activation energy for the glass transition of the blends, and it decreased with an increase in the NBR content. Various theoretical models were used to predict the modulus of the blends. From wide‐angle X‐ray scattering studies, the degree of crystallinity of the blends decreased with an increasing NBR content. The thermal behavior of the uncrosslinked and crosslinked systems of NBR/EVA blends was analyzed using a differential scanning calorimeter. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1556–1570, 2002     

Effects of chain configuration on UCST behavior in blends of poly(L‐lactic acid) with tactic poly(methyl methacrylate)s

Chain configuration influences phase behavior of blends of poly(methyl methacrylate) (PMMA) of different tactic configurations (syndiotacticity, isotacticity, or atacticity) with poly(L ‐lactic acid) (PLLA). Blends system of sPMMA/PLLA is immiscible with an asymmetry‐shaped UCST at ～250 °C. The phase behavior of the sPMMA/PLLA blend is similar to the aPMMA/PLLA blend that has been already proven in the previous work to exhibit similar UCST temperatures (230–250 °C) and asymmetry shapes in the UCST diagrams. On the other hand, the iPMMA/PLLA blend remains immiscible up to thermal degradation without showing any transition to UCST upon heating. The blend system with UCST, that is, sPMMA/PLLA, can be frozen in a state of miscibility by quenching to rapidly solidify from the homogeneous liquid at UCST, where the T_g‐composition relationship for the sPMMA/PLLA blend fits well with the Gordon‐Taylor T_g model with k = 0.15 and the blend's T leads to χ₁₂ = ?0.26 for the UCST‐quenched sPMMA/PLLA blend. Both parameters (k and χ) as characterized for the frozen miscible blend suggest a relatively weak interaction between the two constituents (sPMMA and PLLA) in the blends. The interaction strength is likely not strong enough to maintain a thermodynamic miscibility when the blend is at ambient temperature or any lower temperatures below UCST. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 2355–2369, 2008     

Enhanced stereocomplex formation of poly(L-lactic acid) and poly(D-lactic acid) in the presence of stereoblock poly(lactic acid)

Stereoblock poly(lactic acid) (sb-PLA) is incorporated into a 1:1 polymer blend system of poly(L-lactic acid) (PLLA) and poly(D-lactic acid) (PDLA) that has a high molecular weight to study its addition effect on the stereocomplex (sc) formation of PLLA and PDLA. The ternary polymer blend films are first prepared by casting polymer solutions of sb-PLA, PLLA, and PDLA with different compositions. Upon increasing the content of sb-PLA in the blend films the sc crystallization is driven to a higher degree, while the formation of homo-chiral (hc) crystals is decreased. Lowering the molecular weight of the incorporated sb-PLA effectively increases the sc formation. Consequently, it is revealed that sb-PLA can work as a compatibilizer to improve the poor sc formation in the polymer blend of PLLA and PDLA.     

制备聚(L-乳酸-co-乙醇酸）/聚D-乳酸共混物立构复合物的新方法

首次以高分子量的聚(L-乳酸-co-乙醇酸）(PLLGA）和D-聚乳酸（PDLA)［m(PLLGA) : m(PDLA)=3:1, c 50 mL·g^-1］为原料,氯仿为溶剂,等体积的甲醇为沉淀剂,于50 ℃蒸发4 h形成了PLLGA和PDLA的立构复合物（sc-PLA）,其结构和性能经XRD, DSC和TGA表征。结果表明：sc-PLA的结晶度达96.2%,热失重5%温度为342 ℃（PLLGA为304 ℃）。     

Role of thermal history on the thermal behavior of poly(<Emphasis Type="Italic">L</Emphasis>-lactic acid) studied by DSC and optical microscopy

Summary The thermal behavior of poly(L-lactic acid) (PLLA) was studied with differential scanning calorimetry (DSC) and polarized optical microscopy. For amorphous PLLA samples, double cold crystallisation peaks were observed in the DSC traces during heating process, being strongly dependent on heating rates. The observation was discussed based on the assumption that the quenched PLLA sample presented some remaining metastable or a precrystalline phase. A small exothermal peak was observed before the main melting peak at low heating rates. The probable reason was discussed through melt-recrystallisation mechanism. Influence of thermal history on the cold crystallisation and melting behavior was also performed on heating process for PLLA samples.     

Nonisothermal crystallization behavior of the poly(ethylene glycol) block in poly(L‐lactide)–poly(ethylene glycol) diblock copolymers: Effect of the poly(L‐lactide) block length

The confined crystallization behavior, melting behavior, and nonisothermal crystallization kinetics of the poly(ethylene glycol) block (PEG) in poly(L ‐lactide)–poly(ethylene glycol) (PLLA–PEG) diblock copolymers were investigated with wide‐angle X‐ray diffraction and differential scanning calorimetry. The analysis showed that the nonisothermal crystallization behavior changed from fitting the Ozawa equation and the Avrami equation modified by Jeziorny to deviating from them with the molecular weight of the poly(L ‐lactide) (PLLA) block increasing. This resulted from the gradual strengthening of the confined effect, which was imposed by the crystallization of the PLLA block. The nucleation mechanism of the PEG block of PLLA15000–PEG5000 at a larger degree of supercooling was different from that of PLLA2500–PEG5000, PLLA5000–PEG5000, and PEG5000 (the numbers after PEG and PLLA denote the molecular weights of the PEG and PLLA blocks, respectively). They were homogeneous nucleation and heterogeneous nucleation, respectively. The PLLA block bonded chemically with the PEG block and increased the crystallization activation energy, but it provided nucleating sites for the crystallization of the PEG block, and the crystallization rate rose when it was heterogeneous nucleation. The number of melting peaks was three and one for the PEG homopolymer and the PEG block of the diblock copolymers, respectively. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3215–3226, 2006     

Separation and enzymatic degradation of blend films of poly(L-lactic acid) and cellulose

Blend films of poly(L -lactic acid) (PLLA) and cellulose with various composition was prepared by casting from trifluoroacetic acid solution. One hydroxyl group per each glucose unit was esterified by trifluoroacetic acid. The trifluoroacetyl group was hydrolyzed completely during the degradation. Weight losses for 90/10 and 75/25 PLLA/cellulose blends by proteinaze K were greatly increased compared with pure PLLA sample due to the large depression of the crystallinity of PLLA component, while cellulase was effective only for the degradation of pure cellulose film. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1861–1864, 1998     

Isothermal and nonisothermal crystallization kinetics of poly(propylene terephthalate)

The kinetics of crystallization of poly(propylene terephthalate) (PPT) samples of different molecular weights were studied under both isothermal and nonisothermal conditions. The Avrami and Lauritzen–Hoffmann treatments were applied to evaluate kinetic parameters of PPT isothermal crystallization. It was found that crystallization is faster for low‐molecular‐weight samples. The modified Avrami equation, and the combined Avrami–Ozawa method were found to successfully describe the nonisothermal crystallization process. Also, the analysis of Lauritzen–Hoffmmann was tested and it resulted in values close to those obtained with isothermal crystallization data. The nonisothermal kinetic data were corrected for the effect of the temperature lag and shifted alone with the isothermal kinetic data to obtain a single master curve, according to the method of Chan and Isayev, testifying to the consistency between the isothermal and corrected nonisothermal data. A new method for ranking of polymers, referring to the crystallization rates, was also introduced. This involved a new index that combines the maximum crystallization rate observed during cooling with the average crystallization rates over the temperature range of the crystallization peak. Furthermore, the effective energy barrier of the dynamic process was evaluated with the isoconversional methods of Flynn and Friedmann. It was found that the energy barrier is lower for the low‐molecular‐weight PPT. The effect of the catalyst remnants on the crystallization kinetics was also investigated and it was found that this is significant only for low‐molecular‐weight samples. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3775–3796, 2004     

Superiority of poly(L-lactic acid) microspheres as dermal fillers

The demand for injectable dermal filler has unde rgone significant growth with the rapid development of the beauty industry.Poly(lactic acid)(PLA) as a benefit of excellent biocompatibility and long-term promotion of collagen regeneration has been favored as a commonly used filler.However,the effects of chirality and particle size of PLA on the efficacy of dermal filler have not been studied.In this study,we prepared three kinds of microspheres(MSs) consisting of poly(D-lactic acid)(PDLA MS),poly(L-lactic acid)(PLLA MS),or meso-PLA(PDLLA MS)at 5,10 and 20 μmto reveal the different biological functions as dermal filler.Following intradermal injection into guinea pig,it was found that PLLA MS induced the slightest inflammation,and the level of pro-inflammatory cytokine IL-1β induced by PLLA MS is only 0.3 or 0.7-fold of that induced by PDLA or PDLLA MS,respectively.More importantly,PLLA MS significantly stimulated the regeneration of collagen,which was 1.4 or 1.1 times higher than those stimulated by PDLA MS or PDLLA MS,respectively.The size of PLA MSs did not affect the levels of inflammation and collagen regeneration.The results confirmed the superiority of PLLA as a dermal filler.     

The multiple melting endotherms from poly(butylene terephthalate)

The melting behavior of poly(butylene terephthalate) (PBT) has been investigated, and a simulation has been performed to determine whether the multiple melting endotherms observed during the thermal analysis of PBT can be explained by the simultaneous melting and recrystallization of an initial distribution of crystal melting temperatures that contains only one maximum and two inflection points. Specimens that were cooled at constant rates from the melt showed between one and three melting endotherms upon heating in a differential scanning calorimeter (DSC). The position and breadth of the crystallization exotherms upon cooling from the melt and small-angle x-ray scattering showed that as the cooling rate is increased, the distribution of melting temperatures broadens and shifts to lower temperatures. By combining temperature-dependent recrystallization with an initial distribution of melting temperatures, simulated DSC curves were produced that agreed well with experimental DSC curves. In instances of triple peaked curves, the high temperature peak was due to crystals formed during the scanning process, and the middle and low temperature peaks were due to crystals originally present in the material. Satisfactory agreement between the experimental and simulated curves was found without considering additional crystallization from the amorphous regions during the scanning process.     

Thermal conductivity of poly(L‐Lactic Acid) subjected to elongational deformations

The thermal conductivity of poly(L‐lactic acid) specimens subjected to uniaxial elongational deformations in the rubbery state followed by quenching is investigated experimentally. A novel optical technique known as forced Rayleigh scattering is used to measure two components of the thermal diffusivity tensor as a function of elongation. The component along the direction of elongation increases, while the component in the direction perpendicular to elongation decreases, relative to the equilibrium value. Measurements of the stress at the point of quenching, as well as the density and specific heat capacity, are also reported as a function of elongation. Anisotropy of the thermal conductivity tensor is more than 50% at moderate elongations, and it is found to be a nonlinear function of stress. The latter is in contrast to results found in previous studies where a linear relationship between thermal conductivity anisotropy and stress, or the stress‐thermal rule, has been observed for several amorphous polymer systems. Failure of the stress‐thermal rule is attributed to the presence of semicrystalline domains in the deformed samples. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 547–553     

Miscibility and hydrogen‐bonding interactions in blends of carbon dioxide/epoxy propane copolymer with poly(p‐vinylphenol)

The miscibility and hydrogen‐bonding interactions of carbon dioxide and epoxy propane copolymer to poly(propylene carbonate) (PPC)/poly(p‐vinylphenol) (PVPh) blends were investigated with differential scanning calorimetry (DSC), Fourier transform infrared (FTIR) spectroscopy and X‐ray photoelectron spectroscopy (XPS). The single glass‐transition temperature for each composition showed miscibility over the entire composition range. FTIR indicates the presence of strong hydrogen‐bonding interassociation between the hydroxyl groups of PVPh and the oxygen functional groups of PPC as a function of composition and temperature. XPS results testify to intermolecular hydrogen‐bonding interactions between the oxygen atoms of carbon–oxygen single bonds and carbon–oxygen double bonds in carbonate groups of PPC and the hydroxyl groups of PVPh by the shift of C_1s peaks and the evolution of three novel O_1s peaks in the blends, which supports the suggestion from FTIR analyses. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1957–1964, 2002     

Pore structure and glass transition temperature of nanoporous poly(ether imide)

The effect of nanopores on the glass transition temperature (T_g) of poly(ether imide) was studied with differential scanning calorimetry. Nanoporous poly(ether imide) samples were obtained through the phase separation of immiscible blends of poly(ether imide) and polycaprolactone diol and by the removal of the dispersed minor phase domains with a selective solvent. Microscopy and statistical methods were used to characterize the pore structure and obtain the pore structure parameters. The pore size was found to depend on the processing time and the initial blend composition, mainly because of phase-coarsening kinetics. A decrease in T_g was observed in the nanoporous poly(ether imide) in comparison with the bulk samples. The change in T_g was strongly influenced by the pore structure and was explained by the percolation theory. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3546–3552, 2006     

Segmented block copolymers of poly(ethylene glycol) and poly(ethylene terephthalate)

A new series of segmented copolymers were synthesized from poly(ethylene terephthalate) (PET) oligomers and poly(ethylene glycol) (PEG) by a two‐step solution polymerization reaction. PET oligomers were obtained by glycolysis depolymerization. Structural features were defined by infrared and nuclear magnetic resonance (NMR) spectroscopy. The copolymer composition was calculated via ¹H NMR spectroscopy. The content of soft PEG segments was higher than that of hard PET segments. A single glass‐transition temperature was detected for all the synthesized segmented copolymers. This observation was found to be independent of the initial PET‐to‐PEG molar ratio. The molar masses of the copolymers were determined by gel permeation chromatography (GPC). © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4448–4457, 2004