Model filled rubber. II. Particle composition dependence of suspension rheology

Monodisperse size colloidal particles varying in chemical composition were synthesized by emulsifier‐free emulsion polymerization. Using a stress‐controlled rheometer, the rheological behavior of colloidal suspensions in a low molecular weight liquid polysulfide was investigated. All suspensions exhibited shear thinning behavior. The shear viscosity, dynamic moduli, and yield stress increased as interactions between particles and matrix increased. The rheological properties associated with network buildup in the suspensions were sensitively monitored by a kinetic recovery experiment. We propose that interfacial interactions by polar and hydrogen bonding between particles and matrix strongly promote affinity of matrix polymer to the filler particles, resulting in adsorption or entanglement of polymer chains on the filler surface. A network structure was formed consisting of particles with an immobilized polymer layer on the particle surface with each particle floc acting as a temporary physical crosslinking site. As the interfacial interaction increases, the adsorbed layer thickness on the filler particles, hence, the effective particle volume fraction, increases. As a result, the rheological properties were enhanced in the order PS < PMMA < PSVP. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 815–824, 1999     

Interfacial rheology of stable and weakly aggregated two-dimensional suspensions

The interfacial rheological properties of stable and weakly aggregated two-dimensional suspensions are studied experimentally using a magnetic rod interfacial rheometer. Particle monolayers with well controlled structures were prepared. Charged polystyrene particles create two-dimensional colloidal crystals at the water-decane interface over a wide range of concentrations. Under similar conditions a predominantly liquid structure is obtained at the water-air interface for the same particles. The addition of appropriate combinations of the anionic surfactant sodiumdodecylsulfate (SDS) and sodium chloride (NaCl) to the aqueous subphase leads to a destabilization of these monolayers with the formation of fractal aggregates at low concentrations and a heterogeneous gel forming as the surface coverage is increased. After the structures have been built up a reproducible structure can be obtained, of which the interfacial rheological properties can be investigated using a magnetic rod stress rheometer. In all cases, numerical calculations were used to assess the importance of instrumental artifacts and the effect of the coupling between surface and subphase flows. The rheology of aggregated suspensions was compared to the reference case of a colloidal crystal. The two-dimensional aggregated suspensions display rheological features which are similar to their three-dimensional counterparts. These include an elastic response with small linearity limits, a power law dependence on surface coverage and a dependence on the strength of attraction. The results shed some light on the possible role of interfacial rheology on the stability of particle laden high interface systems. Additionally, the 2D suspensions could present fundamental insights in the rheological properties of dense colloidal suspensions.     

Rheology of particulate rafts,films, and foams

Liquid foam exhibits remarkable rheological behavior although it is made with simple fluids: it behaves similar to a solid at low shear stress but flows similar to a liquid above a critical shear stress. Such properties, which have been proved to be useful for many applications, are even enhanced by adding solid particles. Depending on their hydrophobicity and size, the particles can have different geometrical configurations at the mesoscopic scale, that is, at the air–liquid interfaces, in the films, or in the interstices between the bubbles. In this review, we present rheological studies performed on granular rafts and films, on spherical armored interfaces, on gas marbles, and on aqueous foams laden with hydrophilic grains.     

Active colloidal particles at fluid-fluid interfaces

This review explores the intersection between two important fields of colloid and interface science – that of active colloidal particles and of (passive) particles at fluid-fluid interfaces. The former uses energy input at the particle level to propel particle motions and direct dynamic assemblies. The latter relies on the spontaneous adsorption of particles at fluid interfaces to modify the interfacial energy, rheology, and permeability of biphasic materials. Here, we address two key questions that connect these otherwise distinct fields of study. How do liquid interfaces influence the dynamics of active or driven colloidal particles? How can particle activity influence the dynamics of liquid interfaces? These questions motivate the pursuit of active particle surfactants that move and organize at fluid interfaces to perform useful functions such as enhancing mass transport or modulating interfacial properties. Drawing examples from the literature, we discuss how fluid interfaces can provide a unique environment for the study of active colloids, how surface tension can be harnessed to propel particle motions, and how capillary interactions can be activated to achieve dynamically tunable emulsions and foams. We highlight opportunities for the future study and application of active particles at liquid interfaces.     

胶体颗粒在液-液界面上的吸附行为及界面组装

综述了胶体颗粒在油水界面上的吸附行为及其应用。胶体颗粒在界面上的吸附行为主要受颗粒大小、相互作用力、电性质及润湿性质等因素的影响。本文第一部分主要从作用力出发阐述了胶体颗粒在液-液吸附过程中各种影响因素的理论研究进展;第二部分主要阐述了胶体颗粒在液-液界面上的吸附能够在界面组装、乳液和具有特殊功能的新材料制备等领域中的应用。     

胶体颗粒在液-液界面上的吸附行为及界面组装

综述了胶体颗粒在油水界面上的吸附行为及其应用.胶体颗粒在界面上的吸附行为主要受颗粒大小、相互作用力、电性质及润湿性质等因素的影响.本文第一部分主要从作用力出发阐述了胶体颗粒在液-液吸附过程中各种影响因素的理论研究进展;第二部分主要阐述了胶体颗粒在液-液界面上的吸附能够在界面组装、乳液和具有特殊功能的新材料制备等领域中的应用.     

Effect of nanoparticles on the interfacial properties of liquid/liquid and liquid/air surface layers

An investigation is reported on the interfacial properties of nanometric colloidal silica dispersions in the presence of a cationic surfactant. These properties are the result of different phenomena such as the particle attachment at the interface and the surfactant adsorption at the liquid and at the particle interfaces. Since the latter strongly influences the hydrophobicity/lipophilicity of the particle, i.e., the particle affinity for the fluid interfacial environment, all those phenomena are closely correlated. The equilibrium and dynamic interfacial tensions of the liquid/air and liquid/oil interfaces have been measured as a function of the surfactant and particle concentration. The interfacial rheology of the same systems has been also investigated by measuring the dilational viscoelasticity as a function of the area perturbation frequency. These results are then crossed with the values of the surfactant adsorption on the silica particles, indirectly estimated through experiments based on the centrifugation of the dispersions. In this way it has been possible to point out the mechanisms determining the observed kinetic and equilibrium features. In particular, an important role in the mixed particle-surfactant layer reorganization is played by the Brownian transport of particles from the bulk to the interface and by the surfactant redistribution between the particle and fluid interface.     

From colloidal stability in ionic liquids to advanced soft materials using unique media

Owing to their fascinating properties, ionic liquids (ILs) are now receiving a great deal of attention as alternatives to organic solvents and electrolyte solutions and as synthetic and dispersion media for colloidal systems. Colloidal stability is an essential factor in determining the properties and performance of colloidal systems combined with ILs. The remarkable properties of ILs primarily originate from their highly ionic nature. Although such high ionic strength often causes colloidal aggregation in aqueous and organic suspensions, some colloidal particles can be well suspended in ILs without any stabilizers. In the first part of this article, we focus on recent experiments conducted to investigate the colloidal stability of bare and polymer-grafted silica nanoparticles and on the surface force between silica substrates and ILs. Three different repulsions between colloidal particles (i.e., electrostatic, steric, and solvation forces) are also highlighted, after which a possible interpretation of the results in terms of the stabilization mechanism in ILs both in the presence and in the absence of stabilizers is proposed. The latter part of this article provides an overview of our recent studies on colloidal soft materials with ILs. On the basis of the dispersed states of the silica colloids in ILs, two different soft materials, a colloidal gel and a colloidal glass in ILs, were fabricated. The relationship between their functional properties, such as ionic transport, rheological properties, and optical properties, and the microstructure of the colloidal materials is also described.     

Electrical surface charge and potential of hematite/yttrium oxide core–shell colloidal particles

Interest in the synthesis of composite colloidal particles consisting of a core and shell with different compositions stems from the fact that such particles can be useful in processes where the properties of both core (e.g., size and shape homogeneity, ease of preparation in large amounts, magnetic characteristics, etc.) and shell (interfacial properties, porosity, chemical stability, etc.) might be of interest. However, the applicability must be based on a proper characterization of those properties. In this work, colloidal spheres of hematite (α-Fe₂O₃) were used as nuclei of mixed particles where the shell is yttrium oxide. The electrical properties of the aqueous interface are compared to those of the pure oxides by means of potentiometric titration of their surface charge and potential against pH, as a function of indifferent electrolyte concentration. It is found that the mixed particles efficiently mimic yttrium oxide, since the behavior of their surface electrical characteristics closely resembles that of the latter compound. Differences are found, however, that can be ascribed to an incomplete or porous coverage, but such divergences are of little significance when an overall comparison is carried out. Received: 30 January 2001 Accepted: 11 July 2001     

Colloidal interactions between Langmuir-Blodgett bitumen films and fine solid particles

In oil sand processing, accumulation of surface-active compounds at various interfaces imposes a significant impact on bitumen recovery and bitumen froth cleaning (i.e., froth treatment) by altering the interfacial properties and colloidal interactions among various oil sand components. In the present study, bitumen films were prepared at toluene/water interfaces using a Langmuir-Blodgett (LB) upstroke deposition technique. The surface of the prepared LB bitumen films was found to be hydrophobic, comprised of wormlike aggregates containing a relatively high content of oxygen, sulfur, and nitrogen, indicating an accumulation of surface-active compounds in the films. Using an atomic force microscope, colloidal interactions between the LB bitumen films and fine solids (model silica particles and clay particles chosen directly from an oil sand tailing stream) were measured in industrial plant process water and compared with those measured in simple electrolyte solutions of controlled pH and divalent cation concentrations. The results show a stronger long-range repulsive force and weaker adhesion force in solutions of higher pH and lower divalent cation concentration. In plant process water, a moderate long-range repulsive force and weak adhesion were measured despite its high electrolyte content. These findings provide more insight into the mechanisms of bitumen extraction and froth treatment.     

Stabilization of oil-in-water emulsions by colloidal particles modified with short amphiphiles

Emulsions stabilized through the adsorption of colloidal particles at the liquid-liquid interface have long been used and investigated in a number of different applications. The interfacial adsorption of particles can be induced by adjusting the particle wetting behavior in the liquid media. Here, we report a new approach to prepare stable oil-in-water emulsions by tailoring the wetting behavior of colloidal particles in water using short amphiphilic molecules. We illustrate the method using hydrophilic metal oxide particles initially dispersed in the aqueous phase. The wettability of such particles in water is reduced by an in situ surface hydrophobization that induces particle adsorption at oil-water interfaces. We evaluate the conditions required for particle adsorption at the liquid-liquid interface and discuss the effect of the emulsion initial composition on the final microstructure of oil-water mixtures containing high concentrations of alumina particles modified with short carboxylic acids. This new approach for emulsion preparation can be easily applied to a variety of other metal oxide particles.     

Colloidal aggregate micromechanics in the presence of divalent ions

Colloidal gels exhibit rheological properties, such as a yield stress and elasticity, which arise from the manner in which stress is transmitted through the microstructure. Insight into the mechanisms of stress transmission is critical in developing a full understanding of the mechanics of these materials. Paramount to this is a thorough knowledge of the interparticle interactions. In this work, we use optical trapping to study interactions between poly(methyl methacrylate) (PMMA) particles in adhesive contact by measuring the bending elasticity of directly assembled colloidal aggregates under various physicochemical conditions. The simplified geometry of the aggregate enables us determine the single-bond rigidity, which can then be related to the work of adhesion, W(SL), through the Johnson-Kendall-Roberts (JKR) theory of adhesion. We find that W(SL) is independent of ionic strength in flocculating monovalent salt solutions. However, more complex behavior is observed for divalent salts. Using zeta-potential measurements, we show that divalent cations adsorb to the particle surface. This results in the formation of ionic bridges between particles in adhesive contact. A model of the aggregate micromechanics that considers the divalent ion contribution to the surface energy provides a direct link between the interfacial properties of the particles, nanoscale contact interactions between particles, and the bulk gel modulus.     

Study of the magnetorheological response of aqueous magnetite suspensions stabilized by acrylic acid polymers

In this paper we describe the magnetorheological (MR) behavior of aqueous suspensions consisting of magnetite particles stabilized by poly(acrylic acid) polymers (PAA). A previous work on the colloidal stability of the same systems for different pH values and polymer concentrations demonstrated that the addition of PAA polymers has a very significant effect on the stability. In the present contribution, we study the MR effect of the suspensions stabilized by two different commercial polymers, as a function of pH, magnetic field strength and magnetite volume fraction. All the results are discussed in terms of the interfacial properties of the systems. It is demonstrated that for a given concentration of micrometer particles, the rheological response strongly depends on pH, on the volume fraction of magnetite particles, on the type of polymer added for increasing the stability and on the magnetic field strength. Changing the polymer used provokes clear rheological differences for the same sample conditions (field strength, volume fraction and pH). This is suggested to be due to the hydrophobic/hydrophilic balance of the polymer affecting the magnetic field ability to form magnetic structures by aggregation of the magnetized particles. The results are compared to the predictions of the so-called standard chain model, based on the assumption that the MR effect is the result of the balance between the magnetic interactions (tending to establish some degree of order in the suspension by formation of particle chains in the direction of the field) and hydrodynamic ones (tending to destroy the formed structures by viscous stress on the chains). It is found that the behavior of the yield stress does not agree well with the predictions of the model when the relative proportion of both particle and polymer confers optimum stability to the dispersions. This is likely due to the fact that the presence of the stabilizing polyelectrolyte provokes that the magnetic field is not as effective in structuring the suspension as deduced from the chain model.     

Characteristics of pickering emulsion gels formed by droplet bridging

We experimentally characterize the microstructure and rheology of a carefully designed mixture of immiscible fluids and near-neutral-wetting colloidal particles. Particle bridging across two fluid interfaces provides a route to highly stable gel-like emulsions at volume fractions of the dispersed phase well below the random close-packing limit for spheres. We investigate the microstructural origins of this behavior by confocal microscopy and reveal a percolating network of colloidal particles that serves as a cohesive scaffold, bridging together droplets of the dispersed phase. Remarkably, the mixture's salient rheological characteristics are governed predominantly by the solids loading and can be tailored irrespective of the droplet volume fraction. The identification of this rheological hallmark could provide a means toward the improved design of modern products that utilize solid-stabilized interfaces.     

Interfacial shear rheology of protein-surfactant layers

The shear rheology of adsorbed or spread layers at air/liquid and liquid/liquid phase boundaries is relevant in a wide range of technical applications such as mass transfer, monolayers, foaming, emulsification, oil recovery, or high speed coating. Interfacial shear rheological properties can provide important information about interactions and molecular structure in the interfacial layer. A variety of measuring techniques have been proposed in the literature to measure interfacial shear rheological properties and have been applied to pure protein or mixed protein adsorption layers at air/water or oil/water interfaces. Such systems play for example an important role as stabilizers in foams and emulsions. The aim of this contribution is to give a literature overview of interfacial shear rheological studies of pure protein and protein/surfactant mixtures at liquid interfaces measured with different techniques. Techniques which utilize the damping of waves, spectroscopic or AFM techniques and all micro-rheological techniques will not discuss here.     

Materials based on solid-stabilized emulsions

Solid-stabilized emulsions are obtained by shearing a mixture of oil, water, and solid colloidal particles. In this article, we present a large variety of materials, resulting from a limited coalescence process. Direct (o/w), inverse (w/o), and multiple (w/o/w) emulsions that are surfactant-free and monodisperse were produced in a very wide droplet size range, from micrometers to centimeters. These materials exhibit original properties compared with surfactant-stabilized emulsions: outstanding stability with respect to coalescence and unusual rheological behavior. For such systems, the elastic storage modulus G' is not controlled by interfacial tension but by the interfacial elasticity resulting from the strong adhesion between the solid particles adsorbed at the oil-water interface. Due to the wide accessible droplet size range, concentrated emulsions can be extremely fluid while emulsions with low droplet volume fraction can behave as solids.     

Pickering emulsions: wetting and colloidal stability of hairy particles--a self-consistent field theory

The assembly of sterically stabilized colloids at liquid-liquid interfaces is studied with the self-consistent field (SCF) theory using the discretization scheme that was developed by Scheutjens, Fleer, and co-workers. The model is based on a poly(methyl methacrylate) (pMMA) particle with poly(isobutylene) (pIB) grafted to the surface. The stabilizing groups on the particle surface have a significant effect on the interfacial assembly and, therefore, also on the formation and properties of Pickering emulsions. The wetting behavior of the particle is altered by the presence of the stabilizing groups, which affects the equilibrium position of the particles at the interface. The stabilizing groups can also lead to an activation barrier before interfacial adsorption, analogous to the steric repulsion between two particles. These effects are numerically solved with the SCF theory. It is commonly known that flocculating conditions enhance the interfacial adsorption and yield stable Pickering emulsions, which is confirmed in this work. Additionally, it is concluded that those conditions are not an absolute requirement. There is a window of stabilizer concentrations Γ(pIB), 2.2-3.3 mg/m(2) pIB, that shows both partial wetting and colloidal stability. The activation barrier for interfacial assembly is 140-550 k(B)T and is an order of magnitude higher than the colloidal stability. The difference can be attributed to the unfavorable interaction of pIB with water and a difference in geometry (plate-sphere vs sphere-sphere). This study demonstrates the interplay and provides a quantitative comparison between the wetting behavior and the colloidal stability, and it gives a better understanding of the colloidal assembly at soft interfaces and formation of Pickering emulsions in general.