Synthesis of iron oxide/poly(methyl methacrylate) composite latex particles: Nucleation mechanism and morphology

A magnetic poly(methyl methacrylate) (PMMA) composite latex was prepared by soapless emulsion polymerization in the presence of ferrofluid, and the ferrofluid was prepared by means of a coprecipitation method. The effects of various polymerization parameters, such as the monomer concentration, ferrofluid content, and initiator concentration, on the conversion curve and particle size of the magnetic composite latex particles were examined in detail. The results showed that two nucleation mechanisms were involved according to the polymerization conditions. In the monomer‐rich and less ferrofluid system, self‐nucleation of PMMA was dominant over the entire course of emulsion polymerization. In the ferrofluid‐rich system, seeded emulsion polymerization was the main course to form the magnetic composite latex particles. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5695–5705, 2004     

Synthesis of PMMA‐b‐PBA block copolymer in homogeneous and miniemulsion systems by DPE controlled radical polymerization

In this research, poly(methyl methacrylate)‐b‐poly(butyl acrylate) (PMMA‐b‐PBA) block copolymers were prepared by 1,1‐diphenylethene (DPE) controlled radical polymerization in homogeneous and miniemulsion systems. First, monomer methyl methacrylate (MMA), initiator 2,2′‐azobisisobutyronitrile (AIBN) and a control agent DPE were bulk polymerized to form the DPE‐containing PMMA macroinitiator. Then the DPE‐containing PMMA was heated in the presence of a second monomer BA, the block copolymer was synthesized successfully. The effects of solvent and polymerization methods (homogeneous polymerization or miniemulsion polymerization) on the reaction rate, controlled living character, molecular weight (M_n) and molecular weight distribution (PDI) of polymers throughout the polymerization were studied and discussed. The results showed that, increasing the amounts of solvent reduced the reaction rate and viscosity of the polymerization system. It allowed more activation–deactivation cycles to occur at a given conversion thus better controlled living character and narrower molecular weight distribution of polymers were demonstrated throughout the polymerization. Furthermore, the polymerization carried out in miniemulsion system exhibited higher reaction rate and better controlled living character than those in homogeneous system. It was attributed to the compartmentalization of growing radicals and the enhanced deactivation reaction of DPE controlled radical polymerization in miniemulsified droplets. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 4435–4445, 2009     

Preparation and clinical application of immunomagnetic latex

Magnetic poly(methyl methacrylate) (PMMA)/poly(methyl methacrylate‐co‐methacrylic acid) [P(MMA–MAA)] composite polymer latices were synthesized by two‐stage soapless emulsion polymerization in the presence of magnetite (Fe₃O₄) ferrofluids. Different types and concentrations of fatty acids were reacted with the Fe₃O₄ particles, which were prepared by the coprecipitation of Fe(II) and Fe(III) salts to obtain stable Fe₃O₄ ferrofluids. The Fe₃O₄/polymer particles were monodisperse, and the composite polymer particle size was approximately 100 nm. The morphology of the magnetic composite polymer latex particles was a core–shell structure. The core was PMMA encapsulating Fe₃O₄ particles, and the shell was the P(MMA–MAA) copolymer. The carboxylic acid functional groups (COOH) of methacrylic acid (MAA) were mostly distributed on the surface of the composite polymer latex particles. Antibodies (anti‐human immunoglobulin G) were then chemically bound with COOH groups onto the surface of the magnetic core–shell composite latices through the medium of carbodiimide to form the antibody‐coated magnetic latices (magnetic immunolatices). The MAA shell composition of the composite latex could be adjusted to control the number of COOH groups and thus the number of antibody molecules on the magnetic composite latex particles. With a magnetic sorting device, the magnetic immunolatices derived from the magnetic PMMA/P(MMA–MAA) core–shell composite polymer latex performed well in cell‐separation experiments based on the antigen–antibody reaction. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1342–1356, 2005     

苯乙烯-甲基丙烯酸甲酯悬浮-乳液复合聚合过程中聚合物复合粒子组成的变化

采用苯乙烯(St)悬浮聚合过程中滴加甲基丙烯酸甲酯(MMA)乳液聚合组分,悬浮乳液复合聚合(SECP)方法,制备大粒径聚苯乙烯聚甲基丙烯酸甲酯(PS- PMMA)复合粒子.采用FTIR、1H- NMR、13C- NMR分析方法,研究SECP各个时期复合粒子中MMA- St链节摩尔比,发现悬浮粒子中MMA St链节摩尔比逐渐增大,而PMMA乳胶粒子中逐渐减少,表明悬浮相和乳液相间存在物质传递过程.悬浮粒子中MMA链节质量与MMA总投料质量比主要由乳胶粒子生成速率和乳胶粒子向悬浮粒子凝聚速率决定.最终得到的复合粒子除含PS和PMMA均聚物外,还含少量MMA-St共聚物.     

Thermal‐initiating potentialities of poly(methyl methacrylate) peroxide: Metamorphosis of block‐into‐block copolymer and comparative studies on surface texture and morphology

This is the first report concerning the use of vinyl polyperoxide, namely, poly(methyl methacrylate) peroxide (PMMAP), as a thermal initiator for the synthesis of active polymer PMMAP‐PS‐PMMAP by free‐radical polymerization with styrene. The polymerizations have been carried out at different concentrations of macroinitiator PMMAP. The active polymers have been characterized by ¹H NMR, DSC, thermogravimetric analysis, and gel permeation chromatography. PMMAP‐PS‐PMMAP is further used as the thermal macroinitiator for the preparation of another block copolymer, PMMA‐b‐PS‐b‐PMMA, by reacting the active polymers with methyl methacrylate. The block copolymers have been synthesized by varying the concentrations of the active polymers. The mechanism of block copolymers has been discussed, which is also supported by thermochemical calculations. Studies on the surface texture and morphology of the block copolymer of polystyrene (PS) and PMMA material have been carried out using scanning electron microscopy. Furthermore, in this article, a blend of the same constituent materials (PS and PMMA) in proportions (v/v) similar to that contained in block copolymers has been formulated, and the morphology and surface textures of these materials were also investigated. A comparative microscopical evaluation between two processing methods was done for a better understanding of the processing route dependence of the microstructures. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 546–554, 2001     

Synthesis of H‐shaped complex macromolecular structures by combination of atom transfer radical polymerization,photoinduced radical coupling,ring‐opening polymerization,and iniferter processes

Three controlled/living polymerization processes, namely atom transfer radical polymerization (ATRP), ring‐opening polymerization (ROP) and iniferter polymerization, and photoinduced radical coupling reaction were combined for the preparation of ABCBD‐type H‐shaped complex copolymer. First, α‐benzophenone functional polystyrene (BP‐PS) and poly(methyl methacrylate) (BP‐PMMA) were prepared independently by ATRP. The resulting polymers were irradiated to form ketyl radicals by hydrogen abstraction of the excited benzophenone moieties present at each chain end. Coupling of these radicals resulted in the formation of polystyrene‐b‐poly(methyl methacrylate) (PS‐b‐PMMA) with benzpinacole structure at the junction point possessing both hydroxyl and iniferter functionalities. ROP of ε‐caprolactone (CL) by using PS‐b‐PMMA as bifunctional initiator, in the presence of stannous octoate yielded the corresponding tetrablock copolymer, PCL‐PS‐PMMA‐PCL. Finally, the polymerization of tert‐butyl acrylate (tBA) via iniferter process gave the targeted H‐shaped block copolymer. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4601–4607     

Thermal‐initiating potentialities of vinyl polyperoxides: Transmutation of block‐into‐block copolymer and an exploratory investigation of surface texture and morphology

This article describes the first comprehensive study on the use of vinyl polyperoxides, namely, poly(α‐methyl styrene peroxide) (PMSP) and poly(styrene peroxide) (PSP), as thermal initiators for the synthesis of active polymers, PMSP–PS–PMSP/PSP–PS–PSP, by free‐radical polymerization with styrene. The active polymers have been characterized by ¹H NMR, differential scanning calorimetry, thermogravimetric analysis, and gel permeation chromatography analysis. The PMSP–PS–PMSP/PSP–PS–PSP is further used as the thermal macroinitiator for the preparation of another block copolymer, PS‐b‐PMMA, through the reaction of the active polymers with methyl methacrylate. The mechanism of the block copolymer formation is discussed. Having established the scanning micrograph details of the homopolymer phases, we analyze the surface features and morphology of the block copolymer. Furthermore, the distinction in appearance is highlighted with a view toward strengthening the chemistry with the structural appearance in materials processed differently. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3665–3673, 2000     

悬浮-乳液复合聚合聚苯乙烯-聚甲基丙烯酸甲酯复合粒子的颗粒特性和成粒机理

采用在苯乙烯 (St)悬浮聚合过程中滴加甲基丙烯酸甲酯 (MMA)乳液聚合组分的悬浮 乳液复合聚合方法 ,制备大粒径聚苯乙烯 聚甲基丙烯酸甲酯 (PS PMMA)复合粒子 .研究聚合物粒径分布和颗粒形态的变化发现 ,在St悬浮反应中期滴加MMA乳液聚合组分后 ,聚合体系逐渐由悬浮粒子与乳胶粒子并存向形成单峰分布复合粒子转变 ,最终形成核 壳结构完整的大粒径PS PMMA复合粒子 ;在St悬浮反应初期滴加MMA乳液聚合组分 ,St与MMA一起分散成更小液滴 ,反应后期凝并成非核 壳结构复合粒子 ;在St悬浮反应后期滴加MMA乳液聚合组分 ,PMMA乳胶粒子与PS悬浮粒子基本独立存在 .根据以上结果 ,提出了St MMA悬浮 乳液复合聚合的成粒机理 .     

Block and star block copolymers by mechanism transformation 9: Preparation and characterization of poly(methyl methacrylate)/poly(1,3‐dioxepane)/polystyrene ABC miktoarm star copolymers by combination of reversible addition–fragmentation chain‐transfer polymerization and cationic ring‐opening polymerization

The miktoarm ABC star copolymer with three different branches, polystyrene (PS), poly(1,3‐dioxepane) (PDOP), and poly(methyl methacrylate) (PMMA), was successfully prepared. PS with two transfer groups, hydroxyl and dithiobenzoate groups [PS‐HECA‐SC(S)Ph], was synthesized by the reaction of a dithiobenzoate group at the end of PS with hydroxyethylene cinnamate (HECA) in tetrahydrofuran solution. Then, the cationic ring‐opening polymerization of 1,3‐dioxepane was initiated by triflic acid in the presence of PS‐HECA‐SC(S)Ph and diblock copolymer, PS‐PDOP, was formed. Finally, the diblock copolymer with the dithiobenzoate group situated between the two blocks was used in the reversible addition–fragmentation transfer (RAFT) process of methyl methacrylate (MMA). The miktoarm ABC star copolymer S(PS)(PDOP)(PMMA) was characterized by ¹H NMR spectroscopy and gel permeation chromatography. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1243–1250, 2003     

Exfoliation of montmorillonite by the insertion of disklike micelles via the soap‐free emulsion polymerization of methyl methacrylate

Montmorillonites (MMTs) intercalating a potassium persulfate initiator were readily exfoliated in the presence of polymerizing methyl methacrylate during soap‐free emulsion polymerization. Because of the confined space, the polymerizing chains were aggregated into a disk form inside the clay interlayer regions for micellation. It was surprising to find from X‐ray diffraction analysis that the exfoliation of MMT was almost completed in the micellation stage. Further polymerization afforded latex particles of exfoliated poly(methyl methacrylate) (PMMA)–MMT nanocomposites. In addition, two kinds of MMT nanosheets were collected by the removal of PMMA with toluene: One was a single‐layer nanosheet with a thickness of 1.25 nm, and the other was a stacked sheet with an average thickness of 7.5 nm that may have consisted of six individual layers. Electron diffraction analysis revealed that if the individual layer of an MMT nanosheet were not a single crystal, it should contain an ultrathin layer of ice with a commonly occurring hexagonal phase. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5572–5579, 2006     

Heteroarm H‐shaped terpolymers through click reaction

Heteroarm H‐shaped terpolymers, (polystyrene)(poly(methyl methacrylate))‐ poly(tert‐butyl acrylate)‐(polystyrene)(poly(methyl methacrylate)), (PS)(PMMA)‐PtBA‐(PMMA)(PS), and, (PS)(PMMA)‐poly(ethylene glycol)(PEG)‐(PMMA)(PS), through click reaction strategy between PS‐PMMA copolymer (as side chains) with an alkyne functional group at the junction point and diazide end‐functionalized PtBA or PEG (as a main chain). PS‐PMMA with alkyne functional group was prepared by sequential living radical polymerizations such as the nitroxide mediated (NMP) and the metal mediated‐living radical polymerization (ATRP) routes. The obtained H‐shaped polymers were characterized by using ¹H‐NMR, GPC, DSC, and AFM measurements. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1055–1065, 2007     

Chemical reactions occurring in the thermal treatment of PC/PMMA blends

The chemical reactions occurring in the thermal treatment of bisphenol-A polycarbonate (PC) and poly(methyl methacrylate) (PMMA) blends have been investigated by nuclear magnetic resonance (NMR), mass spectrometry (MS), size exclusion chromatography (SEC), and thermogravimetry (TG). Our results suggest that in the melt-mixing of PC/PMMA blends, at 230°C, no exchange reactions occur and that only the depolymerization reaction of PMMA has been observed. In the presence of an ester-exchange catalyst (SnOBu₂), an exchange reaction was found to occur at 230°C, but no trace of PC/PMMA graft copolymer has been observed. Instead, an exchange reaction between the monomer methyl methacrylate (MMA), generated in the unzipping of PMMA chains, and the carbonate groups of PC has been suggested. This is due to the diffusion of MMA at the interface or even into the PC domains, where it can react with PC producing low molar mass PC oligomers bearing methacrylate and methyl carbonate chain ends and leaving the undecomposed PMMA chains unaffected. The TG curves of PC/PMMA blends prepared by mechanical mixing and by casting from THF show two separated degradation steps corresponding to that of homopolymers. This behavior is different from that of a transparent film of PC/PMMA blend, obtained by solvent casting from DCB/CHCl₃, which shows a single degradation step indicating that the degradation rate of PC is increased by the presence of PMMA in the blend. The thermal degradation products obtained by DPMS of this blend consist of methyl methacrylate (MMA), cyclic carbonates arising from the degradation of PMMA and PC, respectively, and a series of open chain bisphenol-A carbonate oligomers with methacrylate and methyl carbonate terminal groups. The presence of the latter compounds suggests a thermally activated exchange reaction occurring above 300°C between MMA and PC. The presence of bisphenol-A carbonate oligomers bearing methyl ether end groups, generated by a thermally activated decarboxylation of the methyl carbonate end groups of PC, has also been observed among the pyrolysis products. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1873–1884, 1998     

Synthesis and characteristics of poly(methacrylic acid‐co‐N‐isopropylacrylamide) thermosensitive composite hollow latex particles and their application as drug carriers

In this work, the poly(methacrylic acid‐co‐N‐isopropylacrylamide) thermosensitive composite hollow latex particles was synthesized by a three‐step reaction. The first step was to synthesize the poly(methyl methacrylate‐co‐methacrylic acid) (poly(MMA‐MAA)) copolymer latex particles by the method of soapless emulsion polymerization. The second step was to polymerize methacrylic acid (MAA), N‐isopropylacrylamide (NIPAAm), and N,N′‐methylenebisacrylamide in the presence of poly(MMA‐MAA) latex particles to form the linear poly(methyl methacrylate‐co‐methacrylic acid)/crosslinking poly(methacrylic acid‐co‐N‐isopropylacrylamide) (poly(MMA‐MAA)/poly(MAA‐NIPAAm)) core–shell latex particles. In the third step, the core–shell latex particles were heated in the presence of ammonia solution to form the crosslinking poly(MAA‐NIPAAm) thermosensitive hollow latex particles. The morphologies of poly(MMA‐MAA)/poly(MAA‐NIPAAm) core–shell latex particles and poly(MAA‐NIPAAm) hollow latex particles were observed. The influences of crosslinking agent and shell composition on the lower critical solution temperature of poly(MMA‐MAA)/poly(MAA‐NIPAAm) core–shell latex particles and poly(MAA‐NIPAAm) hollow latex particles were, respectively, studied. Besides, the poly(MAA‐NIPAAm) thermosensitive hollow latex particles were used as carriers to load with the model drug, caffeine. The effect of various variables on the amount of caffeine loading and the efficiency of caffeine release was investigated. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 5203–5214     

Facile fabrication of monodisperse polymer hollow spheres

This article reports the facile synthesis of monodisperse polymer hollow spheres by seeded emulsion polymerization without additional treatment. In this method, P(St-MMA-MAA) copolymer latex particles were first prepared by emulsifier-free emulsion polymerization and then used as seeds to carry out emulsion polymerization of methyl methacrylate (MMA), divinyl benzene (DVB), and 2-hydroxyethyl methacrylate (HEMA) with potassium persulfate (KPS) as initiator at 80 degrees C. The void of hollow spheres was readily adjusted by changing the monomer/seed weight ratio, and it could be enlarged while the diameters of hollow spheres changed little after etching by dimethyl formamide (DMF). The effects of synthetic parameters including the monomer composition and the properties of seeds on the morphology of hollow spheres were investigated in detail. On the basis of the experimental results, it seemed reasonable to conclude that the formation of hollow spheres was due to the "dissolution" of seeds in monomers and phase separation between the constituent polymers. As a thermodynamic factor, sodium dodecyl sulfate (SDS) would allow the preparation of solid particles depending on its level.     

Preparation of novel suspensions of ZnO/living block copolymer latex nanoparticles via pickering emulsion polymerization and their long term stability

In this work, we present the first Pickering emulsion polymerization with a controlled/living character. Pickering emulsion polymerization in the presence of a novel suspension of zinc oxide/poly(sodium 4‐styrenesulfonate) (ZnO/PSS^?) nanocomposite particles was applied to prepare ZnO/living block copolymer latexes. In the emulsion system, 1,1‐diphenylethene (DPE)‐controlled radical polymerization of poly(methyl methacrylate)‐b‐poly(butyl acrylate) (PMMA‐b‐PBA) was proceeded in oil phase. The nanocomposite particles of ZnO/PSS^? with an average diameter of 20 nm and negatively charged zeta potential around ?30 mV were synthesized via hydrothermal method then served as an effective emulsion stabilizer at the oil/water interface. Living polymerization was carried out using DPE‐capped PMMA as the macroinitiator and PMMA‐b‐PBA block copolymer latex was successfully prepared with coverage of ZnO/PSS^? nanoparticles. Narrow size distributions of the droplets as well as latex particles were obtained, and the livingness of block copolymers was comparable to that of emulsions stabilized by conventional surfactants. The controlled/living character in Pickering emulsion polymerization was slightly influenced by the amount of PSS^? immobilized into the ZnO/PSS^? nanoparticles, whereas it was significantly influenced by the weight ratios between ZnO/PSS^? and oil phase. The Pickering latexes showed excellent long term stability against either coalescence or sedimentation over several months. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Stress–strain behavior of low‐density polyethylene/poly(methyl methacrylate) blends with modulated interfaces with a hydrogenated polybutadiene‐block‐poly(methyl methacrylate) diblock copolymer

The stress–strain diagrams and ultimate tensile properties of uncompatibilized and compatibilized hydrogenated polybutadiene‐block‐poly(methyl methacrylate) (HPB‐b‐PMMA) blends with 20 wt % poly(methyl methacrylate) (PMMA) droplets dispersed in a low‐density polyethylene (LDPE) matrix were studied. The HPB‐b‐PMMA pure diblock copolymer was prepared via controlled living anionic polymerization. Four copolymers, in terms of the molecular weights of the hydrogenated polybutadiene (HPB) and PMMA sequences (22,000–12,000, 63,300–31,700, 49,500–53,500, and 27,700–67,800), were used. We demonstrated with the stress–strain diagrams, in combination with scanning electron microscopy observations of deformed specimens, that the interfacial adhesion had a predominant role in determining the mechanism and extent of blend deformation. The debonding of PMMA particles from the LDPE matrix was clearly observed in the compatibilized blends in which the copolymer was not efficiently located at the interface. The best HPB‐b‐PMMA copolymer, resulting in the maximum improvement of the tensile properties of the compatibilized blend, had a PMMA sequence that was approximately half that of the HPB block. Because of the much higher interactions encountered in the PMMA phase in comparison with those in HPB (LDPE), a shorter sequence of PMMA (with respect to HPB but longer than the critical molecular weight for entanglement) was sufficient to favor a quantitative location of the copolymer at the LDPE/PMMA interface. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 22–34, 2005     

Synthesis of functional graft copolymers by solution copolymerization and their evaluation as dispersants in nonaqueous phase dispersion polymerization

The poly(HEMA‐co‐MMA‐g‐PMMA) graft copolymer was prepared with a poly(methyl methacrylate) (PMMA) macromonomer, 2‐hydroxyethyl methacrylate (HEMA), and methyl methacrylate (MMA), and its application as a dispersant for the nonaqueous phase dispersion polymerization of polystyrene (PST) was investigated. Monodisperse PST particles were obtained with two‐dimensionally tailored graft copolymers, with the number of grafted chains controlled and the polar component (HEMA) in the backbone chains balanced. As for the reactor, a stirred vessel with moderate agitation yielded uniform polymer particles, whereas sealed glass ampules with an overturning motion yielded broader size distributions. Increasing the polarity of the solvent in the continuous phase yielded smaller polymer particles with a gradual deterioration of monodispersity. Uniform polymer particles with a coefficient of variation of less than 6% were obtained up to 30 wt % solid contents. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1788–1798, 2003     

Reverse atom transfer radical polymerization of methyl methacrylate with a new catalytic system,FeCl3/isophthalic acid

A new catalytic system, FeCl₃/isophthalic acid, was successfully used in the reverse atom transfer radical polymerization (RATRP) of methyl methacrylate (MMA) in the presence of a conventional radical initiator, 2,2′‐azo‐bis‐isobutyrontrile. Well‐defined poly(methyl methacrylate) (PMMA) was synthesized in an N,N‐dimethylformamide solvent at 90–120 °C. The polymerization was controlled up to a molecular weight of 50,000, and the polydispersity index was 1.4. Chain extension was performed to confirm the living nature of the polymer. The kinetics of the RATRP of MMA with FeCl₃/isophthalic acid as the catalyst system was investigated. The apparent activation energy was 10.47 kcal/mol. The presence of the end chloride atom on the resulting PMMA was demonstrated by ¹H NMR spectroscopy. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 765–774, 2001     

Synthesis of a ‐shaped amphiphilic block copolymer by the combination of atom transfer radical polymerization and living anionic polymerization

The functionalization of monomer units in the form of macroinitiators in an orthogonal fashion yields more predictable macromolecular architectures and complex polymers. Therefore, a new ‐shaped amphiphilic block copolymer, (PMMA)₂–PEO–(PS)₂–PEO–(PMMA)₂ [where PMMA is poly(methyl methacrylate), PEO is poly (ethylene oxide), and PS is polystyrene], has been designed and successfully synthesized by the combination of atom transfer radical polymerization (ATRP) and living anionic polymerization. The synthesis of meso‐2,3‐dibromosuccinic acid acetate/diethylene glycol was used to initiate the polymerization of styrene via ATRP to yield linear (HO)₂–PS₂ with two active hydroxyl groups by living anionic polymerization via diphenylmethylpotassium to initiate the polymerization of ethylene oxide. Afterwards, the synthesized miktoarm‐4 amphiphilic block copolymer, (HO–PEO)₂–PS₂, was esterified with 2,2‐dichloroacetyl chloride to form a macroinitiator that initiated the polymerization of methyl methacrylate via ATRP to prepare the ‐shaped amphiphilic block copolymer. The polymers were characterized with gel permeation chromatography and ¹H NMR spectroscopy. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 147–156, 2007     

STUDY ON THE POLYMERIZATION KINETICS AND STABILITY OF P(UA)/MMA MICROEMULSION*

 Urethane acrylate anionomer (APUA) as a kind of new type polymerizable emulsifier was synthesized using 2,4-toluene diisocyanate (TDI), polypropylene glycol (PPG), 2-hydroxyethyl methacrylate (HEMA) and dimethylolpropionic acid (DMPA). The critical micelle concentration (CMC) of APUA was measured by the methods of conductance and surface tension. The comparative studies between polymerizable emulsifier AUPA and conventional emulsifier sodium dodecyl sulfate (SDS) were carried out in the emulsion polymerization of methyl methacrylate (MMA). Polymerization kinetics,stability, size and morphology of the latex particles were investigated. It was found that in APUA both water soluble initiator potassium persulfate (KPS) and oil soluble initiator 2,2'-azobisisobutyronitrile (AIBN) can start the reaction of MMA, and the polymerization rate and yield were very high. On using AIBN as an initiator, the conversion-time behavior of MMA with APUA as emulsifier was different to that of SDS as emulsifier, signifying a different nucleation mechanism of the polymer latex particle. The average size of the two kinds of particles is about 50 nm. The particle size decreases with increasing emulsifier concentration. On using KPS as the initiator, APUA as emulsifier, cross-linking hydrogel of PMMA would be formed, but SDS was used as emulsifier and the hydrogel of PMMA was not present.