Tensile modulus of polymer/CNT nanocomposites by effective volume fraction of nanoparticles as a function of CNT properties in the network

In this article, the effects of filler network and interphase between polymer matrix and nanoparticles on the tensile modulus of polymer/carbon nanotubes (CNT) nanocomposites are assumed by the effective volume fraction of nanoparticles. By this approach, the Takayanagi model is developed for polymer/CNT nanocomposites above percolation threshold. Also, the effective factors for filler network including the number (N ), aspect ratio (α ) and percolation threshold (? _p ) of CNT are correlated to three main parameters. The developed model is evaluated for some reported samples from previous papers, and the influences of main parameters on the modulus are examined. The acceptable predictability of the developed model for modulus of nanocomposites is illustrated by experimental results. The “α ” and “N ” parameters play positive roles in the modulus, while an inverse relation is observed between the modulus and the percolation threshold. The reasonable effects of these parameters on the tensile modulus of polymer/CNT nanocomposites are also discussed. Copyright © 2017 John Wiley & Sons, Ltd.     

Influence of the surface chemistry on the structural and mechanical properties of silica‐polymer composites

Poly(vinyl alcohol) (PVA) composite films filled with nanometric, monodisperse, and spherical silica particles were prepared by the mixing of an aqueous PVA solution and SiO₂ colloidal suspension and the evaporation of the solvent. Adjusting the solution pH to 5 and 9 controlled the PVA‐SiO₂ interaction. Adsorption isotherms showed a higher PVA/surface affinity at a lower pH. This interaction influenced the composite structure and the particle distribution within the polymer matrix, which was investigated by small‐angle neutron scattering, electron microscopy, and swelling measurements. Most of the mechanical properties could be related to the composite structure, that is, the distribution of clusters within the polymer matrix. The progressive creation of a cluster network within the polymeric matrix as the silica volume fraction increased reduced the extensibility or swelling capacity of the composite. The effect was more acute at a higher pH, at which the surface interaction with PVA was weaker and promoted the interconnection between clusters. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 3127–3138, 2003     

Determination of tensile strength of UHMWPE fiber-reinforced polymer composites

Quasi-static tensile test of UHMWPE fiber-reinforced composite laminate is challenging to perform due to low interlaminar shear strength and low coefficient of friction. Tensile tests proposed in the literature were conducted and limitations associated with each method led to the evolution of a new method. Tensile test of single-ply was realized as the best representative of tensile strength of a composite than tensile test of UHMWPE laminate. A fixture was developed for single-ply tests which increased friction and provided the mechanical constraint to slipping. The fixture is easy to fabricate and has provided repeatable results for eight grades of UHMWPE fiber-based (0/90) fabrics. Reported tensile strengths are in quite high range of 900–1500 MPa.     

Flammability of carbon nanofiber–clay nanopaper based polymer composites

In this study, a hybrid nanopaper consisting of carbon nanofiber (CNF), and pristine montmorillonite clay (MMT, Cloisite Na⁺) was fabricated through a paper‐making process. The hybrid nanopaper was coated onto the surface of glass fiber (GF) reinforced polymer matrix composites through resin transfer molding process. The characterization results using scanning electron microscopy (SEM) and energy dispersion analysis of X‐ray (EDAX) show that the nanopaper had a porous structure and the polymer resin completely penetrated the hybrid nanopaper. The thermogravimetric analysis (TGA) test results revealed that the addition of MMT clay nanoparticles significantly enhanced the thermal stability of the nanopaper. The flammability of composite samples was evaluated by cone calorimeter test under a radiant heat flux of 50 kW/m². The peak heat release rate (PHRR) was dramatically reduced for the composites coated with the CNF–MMT nanopaper. For comparison, the composites coated with the CNF–organic MMT clay (OMT, Cloisite 20A) nanopaper were also evaluated with cone calorimeter test. The test results showed that the MMT clay was more effective than the OMT in the reduction of the PHRR. The combustion behavior of these samples was also examined by microscale combustion calorimetry (MCC) test. The PHRR obtained from the MCC test decreased with the MMT content in the nanopaper, which was in good agreement with cone calorimeter test results. Copyright © 2010 John Wiley & Sons, Ltd.     

Numerical assessment of the analytical models used to determine flexural and shear moduli in I-Beams when the tensile and compressive moduli are different

The different compressive and tensile moduli of fibre reinforced composites have been considered in the analysis of the flexural and shear moduli of I-beams. Firstly, the neutral axis has been determined analytically and then, assuming that location of the neutral axis, the analytical flexural modulus of I-beams has also been obtained. In order to assess the proposed procedure, virtual pure bending and three-point bending tests at different spans have been carried out using the finite element method. The compressive and tensile moduli have been taken into account by defining two parts in the numerical models. The numerical flexural and shear moduli have been determined by reducing the data obtained in the virtual tests. Analytical and numerical results are in good agreement. Therefore, the flexural modulus determined by the proposed analytical approach can be introduced as a material property in the finite element method.     

Influence of polymer matrix composition and architecture on polymer nanocomposite formation: Coarse-grained molecular dynamics simulation

Coarse-grained molecular dynamics simulations of stacks of two-dimensional platelets immersed in a polymer melt were performed to investigate aspects of the polymer matrix that promote the formation of intercalated or exfoliated nanocomposite structures. Such factors include temperature, copolymer architecture, and blend composition. Increasing the polymer-sheet attractive interaction led to binding of the sheets, where individual beads simultaneously attract two neighboring sheets, thus kinetically blocking intercalation by occupying the perimeter of the affected gallery. Polymers with a small polymer-sheet attraction, but having a strongly attractive chain end (end-functionalized polymers) minimized the bonding of adjacent sheets. These systems exhibited some sheet sliding because a majority of the confined polymer beads only interacted weakly with adjacent sheets; however, the number density of intercalated polymer was low. Mixtures of end-functionalized and nonfunctionalized polymers, however, yielded better intercalation efficiency. For the mixed system, the reduced number of highly attractive beads provided sufficient interaction for intercalation to occur, enabling greater intercalation rates, less sheet-bridging, and incorporation of the nonfunctionalized polymers into the galleries. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 3272–3284, 2003     

Modeling Young’s modulus of rubber–clay nanocomposites using composite theories

The modulus reinforcement of rubber–clay nanocomposites was examined using Guth, Halpin–Tsai and the modified Halpin–Tsai equations, which are universally used for composites reinforced by fiber-like or rod-like fillers. Taking account of the lower contribution of the platelet-like filler to Young’s modulus than that of the fiber-like filler, the modulus reduction factor (MRF) for the platelet-like fillers of 0.66, determined by fitting experimental data, is introduced into the above three equations. The aspect ratios of clay platelets in rubber–clay nanocomposites were determined by statistically analyzing TEM micrographs. The predicting ability of the above three equations for polymer–clay nanocomposites is improved by introducing MRF.     

Orientation transition of nanorods induced by polymer brushes

Coarse-grained molecular dynamics simulations are used to explore the spatial orientations and conformational transitions of nanorods (NRs) within semiflexible polymer brushes. The orientations of the NR clusters are controlled by the competition between the entropy cost for NRs infiltrated into the polymer brushes and the attractive energy between NRs and polymer brushes. By reducing the grafting density or enhancing the number of NRs, the NR cluster experiences an orientation transition from the vertical direction to the horizontal direction. The semiflexible polymer brushes are regarded as the soft confinements for the NRs, and the soft confinements can induce the formation of the NR aggregation under the effect of the depletion attractions. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2013     

Structure of polymer and particle aggregates in hydrogel composites

Knowledge of the structure of a biomaterial is usually vital to control its function. This article provides a structural characterization of a hyaluronan scaffold that has demonstrated good biocompatibility and is used to induce bone regeneration. Hyaluronan hydrogels are appealing materials that can function as a matrix to incorporate both organic and inorganic substances to enhance tissue growth. Because of the intrinsic properties of this swollen matrix, one needs a very sensitive technique that can be applied in situ to determine the organization of the polymers in a gel. Small-angle neutron scattering is used to determine the characteristics of the inhomogeneous structure of the hydrogel both with and without added particles. The results are interpreted using models of structure with two length scales that are beyond the traditional picture of homogeneous gels. The observed structure and the dimensions can explain the previously reported rheological properties of gels containing different amount of polymers. Hydroxyapatite nanoparticles added to the gel are frozen in the gel matrix. We are able to determine the distribution and shape of these particles as they aggregate around the polymer chains. We have also concluded, in this case, that the particle structure is concentration independent. Information about the nanostructure for an applicable biomaterial guides the formulation, preparation, and use that should lead to further understanding of its exploitation. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2013     

Short‐time elasticity of polymer melts: Tobolsky conjecture and heterogeneous local stiffness

An extended molecular‐dynamics study of the short‐time “glassy” elasticity exhibited by a polymer melt of linear fully‐flexible chains above the glass transition is presented. The focus is on the infinite‐frequency shear modulus G_∞ manifested in the picosecond time scale and the relaxed plateau G_p reached at later times and terminated by the structural relaxation. The local stiffness of the interactions with the first neighbors of each monomer exhibits marked distribution with average value given by G_∞. In particular, the neighborhood of the end monomers of each chain are softer than the one of the inner monomers, so that G_∞ increases with the chain length. G_p is not affected by the chain length and is largely set by the nonbonding interactions, thus confirming for polymer melts the conjecture formulated by Tobolsky for glassy polymers. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1401–1407     

A buckling mechanics approach to elastic modulus determination of glassy polymer films

Column buckling mechanics were examined as a technique to determine the modulus of glassy polymer films that fail at very low strains in tension. As an alternative modulus measurement technique, free‐standing column buckling (FSCB) mechanics were investigated here. Given the film geometries and the critical buckling load, classical relationships can be used to determine the modulus. Several polymeric materials were tested and compared to uniaxial tensile values to determine the robustness and validity of the technique. Film geometries were varied from 4 to 18 mm in width and from 15 to 60 mm in length. The films were compressed in plane until buckling occurred and the critical buckling load was measured for each geometry. The critical buckling load increased as film width increased and decreased as film length increased, while the thickness was held constant for each material. For polyethylene terephthalate films, the elastic modulus was determined to be 3.06 ± 0.58 GPa. This FSCB‐determined modulus was compared to the elastic modulus obtained by tensile testing (3.54 ± 0.2 GPa). The modulus measurement technique presented here has the potential to be used experimentally to determine the elastic modulus of glassy polymer films that perform poorly in tension. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 15–20     

Green synthesis of polymer nanofibers and their composites as flame‐retardant materials for polymer nanocomposites

Polyaniline nanofibers and their composites with carbon nanotubes were developed as an effective flame‐retardant material using a facile green method. Polyaniline nanofibers were used as a smart flame‐retardant for acrylonitrile–butadiene–styrene polymer. The polyaniline nanofibers were dispersed in polymer matrix forming well‐dispersed polymer nanocomposites. Effect of polyaniline nanofiber mass ratio on the polymer nanocomposite properties was studied. Polyaniline nanofiber composites with carbon nanotubes were also dispersed in polymer matrix. The thermal stability and flammability properties of the polymer nanocomposites were investigated. The rate of burning of polymer nanocomposites achieved 82.5% reduction (7.32 mm/min) compared with virgin polymer (42.5 mm/min). The reduction in peak heat release rate and total heat release of the polymer nanocomposites containing nanofibers achieved 74 and 34%, respectively. Interestingly, the average mass loss rate was significantly reduced by 58% and the emission of carbon monoxide and carbon dioxide gases were suppressed by 20 and 47%, respectively. The effect of polyaniline nanofibers composites on the flammability of polymer nanocomposites was also studied. Polyaniline nanofibers and their composites were characterized using Fourier transform infrared spectroscopy and transmission and scanning electron microscopy. The dispersion of polyaniline nanofibers in polymer nanocomposites was characterized using transmission electron microscopy. The different polymer nanocomposites were characterized using thermogravimetric analysis, UL94 flame chamber, and cone calorimeter tests. Copyright © 2016 John Wiley & Sons, Ltd.     

Nafion®/(organically modified silicate) nanocomposites via polymer in situ sol–gel reactions: Mechanical tensile properties

A series of Nafion®/[organically modified silicate (ORMOSIL)] hybrid materials have been created by in situ sol–gel copolymerizations of tetraethylorthosilicate and semiorganic silicon alkoxide monomers. The trends in the mechanical tensile properties of these hybrid materials were largely rationalized in terms of the entrapment of the long sulfonic acid side chains in silicate or ORMOSIL structures. There is a significant increase in the mechanical strength relative to that of unfilled Nafion®, except in one case. Young's modulus is enhanced relative to that of unfilled acid form Nafion® in a number of cases, although the degree of ductility is reduced relative to that of unfilled Nafion®. The filler fractions are beneath a critical value that would reflect percolation of a glassy, direct load‐bearing silicate phase. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2237–2247, 2002     

Selective adsorption behavior of polymer at the polymer–nanoparticle interface

Coarse‐grained molecular dynamics simulations are used to investigate the adsorption behavior of monodisperse and bidisperse polymer chains on the nanoparticle (NP) surface at various polymer–NP interactions, chain lengths, and stiffness. At a strong polymer–NP interaction, long chains preferentially occupy interfacial region and squeeze short chains out of the interfacial region. Semiflexible chains with proper stiffness wrap NPs dominantly in a helical fashion, whereas fully flexible chains constitute the surrounding matrix. As chain stiffness increases, the results of the preferential adsorption are the opposite. The chain‐length or chain‐stiffness‐induced selective adsorption behavior of polymer chains in the polymer–NP interfacial region relies on a delicate competition between entropic and enthalpic contributions to the total free energy. These results could provide insights into polymer–NP interfacial adsorption behavior and guide the design of high‐performance nanocomposites. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 1829–1837     

Hybrid metal–polymer composites from functional block copolymers

The combination of metals and polymers in hybrid materials is a research area of great current interest. A number of methods for controlling the positioning of metallic species within polymer matrices on the nanometer scale have been developed. This highlight focuses on the use of functional block copolymers for the localization of metal species, especially nanoparticles, on the nanometer scale through block copolymer phase segregation. Research from the author's group on the use of alkyne‐functional block copolymers for the preparation of cobalt‐containing materials is discussed in this context. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4323–4336, 2005     

Surface modification of magnetic metal nanoparticles and its influence on the performance of polymer composites

To control the interfacial interaction in magnetic metal nanoparticles‐filled polymer composites, surfaces of iron, cobalt, and nickel nanoparticles were grafted by irradiation‐induced polymerization. On the basis of the study of dynamical mechanical behavior, thermal stability, and magnetic performance of the composites prepared by either solution mixing or in situ polymerization, the structure–property relationships of the composites are a function of interfacial interaction and the dispersion state of the nanoparticles. In addition, grafting of polymers onto the surface of the metal nanoparticles changed the surface magnetic state, leading to the possibility of purposely tailoring the magnetic behavior of the composites. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1070–1084, 2003     

Young's modulus of polyethylene in the microstrain region

The stress–strain behavior of various polyethylenes was measured with a strain sensitivity of 2 × 10^?7. Young's modulus was measured as a function of the strain rate. The shapes of the stress–strain curves in the vicinity of room temperature were nonlinear down to the lowest measurable strain. The stress–strain behavior in the microstrain region was well described by the model of the standard linear solid. From the model, the relaxation time was determined along with the relaxed and unrelaxed moduli. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2420–2429, 2001     

Morphology,thermal stability,and flammability of polymer matrix composites coated with hybrid nanopapers

In this study, a hybrid nanopaper consisting of carbon nanofiber (CNF) and polyhedral oligomeric silsequioxane (POSS) or cloisite Na⁺ clay, has been fabricated through the papermaking process. The hybrid nanopaper was then coated on the surface of glass fiber (GF) reinforced polymer matrix composites through resin transfer molding (RTM) process. The morphologies of the hybrid nanopaper and resulting nanocomposites were characterized with scanning electron microscopy (SEM). It can be seen that the nanopaper had a porous structure with highly entangled carbon nanofibers and the polyester resin completely penetrated the nanopaper throughout the thickness. The thermal decomposition behavior of the hybrid nanopapers and nanocomposites was studied with the real‐time thermogravimetric analysis/ flourier transform infrared spectrometry (TGA/FTIR). The test results indicate that the addition of pristine nanoclay increased the thermal stability of the nanopaper, whereas the POSS particles decreased the thermal stability of the nanopaper. The fire retardant performance of composite laminates coated with the hybrid nanopaper was evaluated with cone calorimeter tests using a radiated heat flux of 50 kW/m². The cone calorimeter test results indicate that the peak heat release rate (PHRR) decreased dramatically in composite laminates coated with the CNF‐clay nanopaper. However, the PHRRs of the CNF‐POSS nanopaper coated composite laminates increased. The formation of compact char materials was observed on the surface of the residues of the CNF‐clay nanopaper after cone calorimeter test. The flame retardant mechanisms of the hybrid nanopaper in the composite laminates are discussed. Copyright © 2009 John Wiley & Sons, Ltd.     

Influence of polymer particle size on the percolation threshold of electrically conductive latex‐based composites

Monodispersed copolymer emulsions, each with a different polymer particle size, were used to investigate the effect of particle size on the electrical and thermomechanical properties of carbon black (CB)‐filled segregated network composites. These emulsions were synthesized with equal moles of methyl methacrylate and butyl acrylate, with latex particle size ranging from 83 to 771 nm. The electrical percolation threshold was found to decrease from 2.7 to 1.1 vol % CB as the latex particle size was increased. Microstructural images reveal diminished latex coalescence, and improved CB segregation, with increasing latex particle size. In general, coalescence is shown to increase for all systems with increasing CB concentration. Furthermore, all systems exhibited a similar maximum electrical conductivity plateau of 0.7 S cm^?1, albeit at lower concentration for larger latex particle size. This ability to tailor percolation threshold with latex particle size provides an important tool for manipulating electrical and mechanical properties of polymer nanocomposites. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 49: 1547–1554, 2011