三羟甲基十一烷的合成与表征

三羟甲基烷烃是用于醇酸树脂、聚氨酯树脂、表面活性剂、合成润滑油等的原料[1-3].三羟甲基十一烷(化学结构见图1)作为三羟甲基烷烃中直碳链最长的一员,不仅具有亲水性(分子中含三个亲水基),而且具有疏水性(含一个长直碳链亲油基),因此可用作表面活性剂.不仅如此,与同样用作乳化剂的一般高级脂肪醇(如十六烷醇)相比,可以在化妆品用的乳液中加入三羟甲基十一烷作乳化剂,以降低乳液的黏度,防止乳液中由于大量加入高级脂肪醇而导致产品黏度过高以至不能在皮肤上被充分涂抹开的状况发生[4].为制备智能芳香缓释型聚氨酯微胶囊壳材[5],需要设计聚氨酯的分子结构中含有能与相变石腊和油溶性香料有良好相容性的疏水链(三羟甲基十一烷与六亚甲基二异氰酸酯的加成物).因此,本文合成并表征了三羟甲基十一烷.     

Synthesis and characterization of bismaleimides from epoxy resins

Novel bismaleimides (BMIs) were prepared from functional monomaleimides and diglycidyl ether of bisphenol A (DGEBA) and some of them were shown to have good processibility and improved water resistance while retaining characteristic thermal stability of polyimide. Functional monomaleimides were synthesized via the condensation reaction of maleic anhydride with either aminobenzoic acid or aminophenol. Crosslinking reaction of thus obtained BMIs was carried out with or without catalyst at the temperature range of 100–250°C. The type of the functional group species and their position in monomaleimides significantly affected the crosslinking behavior of the resulting BMIs and the thermal property of their crosslinked products. BMIs with meta linkage, obtained from meta monomaleimides, exhibited much faster thermal crosslinking behavior than corresponding para BMIs. When the molecular weight of BMI was larger, the crosslinking density became smaller and T_g was lower as expected, while the viscosity started to increase at a higher temperature. Glass transition temperatures of the crosslinked resins were in the range of 160–250°C and these resins showed excellent thermal stability up to 370°C.     

含氢低聚硅氧烷合成工艺及表征

以苯基三甲氧基硅烷和四甲基二氢二硅氧烷为合成原料,合成了高产率、高纯度的含多个活性氢基低聚硅氧烷MH3 Tph,采用粘度、折射率、透光率、及核磁共振氢谱、硅谱对其进行了表征.考察了物料投料摩尔比和滴加蒸馏水耗时在合成工艺中的影响,结果表明合成最佳方案为:以1:2.0的比例投料,在低温15℃环境下,滴加酸催化剂0.05 ...     

Synthesis and characterization by MALDI-TOF MS of polycyclic siloxanes derived from p-substituted novolac resins by MALDI-TOF MS

Novel polycyclic siloxane resins were prepared from phenol-formaldehyde novolac type resins by reacting them with dialkyl or diaryl dichlorosilanes under anhydrous and high dilution conditions. The formation of polycyclic species was confirmed by the detection of absolute masses by MALDI-TOF mass spectrometry. ¹H- and ²⁹Si-NMR confirmed the substitutions of phenolic hydroxy groups by siloxane bonds. Curing studies were conducted on the polycyclic siloxane resins as well as on the polycyclic siloxane resins incorporated into two types of polysiloxane gums. A trace amount of potassium hydroxide was used as a catalyst for the crosslinking of these systems. The blend of polysiloxane with 30 wt % polycyclic siloxane was found to be stable at the curing temperature. Differential scanning calorimetry and thermogravimetric analysis techniques were used to study the thermal profiles of these systems. © 1998 John Wiley & Sons, Inc. J. Polym. Sci. A Polym. Chem. 36: 2429–2437, 1998     

Synthesis and characterization of hydroxypropyl cellulose from bacterial cellulose

Bacterial cellulose produced by Acetobacter xylinum has been reacted with propyleneoxide to synthesize hydroxypropyl cellulose(HPC) under different reaction conditions while diluted by toluene. The effects of mass ratio of bacterial cellulose to propyleneoxide, dilutability of toluene, reaction temperature(T) and time(t) were investigated by series of experiments. The degree of substitution(DS), hydroxypropyl content(A) and yield(η) were compared. The optimized product exhibited cold-water solubility and hot-water gelatinization in aqueous medium. Further study was carried out with FTIR, TGA, XRD, SEM and 13C-NMR for characterization. The water/air contact angle measurement reveals that it is a good hydrophobic material with good mechanical properties.     

Accelerated Chemical Reactions and Organic Synthesis in Leidenfrost Droplets

Leidenfrost levitated droplets can be used to accelerate chemical reactions in processes that appear similar to reaction acceleration in charged microdroplets produced by electrospray ionization. Reaction acceleration in Leidenfrost droplets is demonstrated for a base‐catalyzed Claisen–Schmidt condensation, hydrazone formation from precharged and neutral ketones, and for the Katritzky pyrylium into pyridinium conversion under various reaction conditions. Comparisons with bulk reactions gave intermediate acceleration factors (2–50). By keeping the volume of the Leidenfrost droplets constant, it was shown that interfacial effects contribute to acceleration; this was confirmed by decreased reaction rates in the presence of a surfactant. The ability to multiplex Leidenfrost microreactors, to extract product into an immiscible solvent during reaction, and to use Leidenfrost droplets as reaction vessels to synthesize milligram quantities of product is also demonstrated.     

Synthesis and structural characterization of amino-functionalized polysaccharides

A variety of carbohydrates, in particular polysaccharides can be subjected to chemical modification to obtain derivatives with amphiphilic properties, which enable biochemical or biological reactions at the polymer surface. In the present work, a polydisperse maltodextrin mixture of average molecular weight 3000 was coupled with 1,6-hexamethylenediamine (HMD) via reductive amination reaction. Resulting products were characterized by thermal analysis and positive nanoelectrospray quadrupole time-of-flight (Q-TOF) mass spectrometry (MS) and tandem mass spectrometry (MS/MS). Both thermal analysis and MS screening confirmed the formation of the HMD-polysaccharide coupling products. Moreover, HMD-linked polysaccharide chains containing 2 to 26 glucose building blocks were identified by nanoESI Q-TOF MS. MS/MS fragmentation using collision-induced dissociation (CID) at low ion acceleration energies provided strong evidence for HMD-maltodextrin linkage formation and the set of sequence ions diagnostic for the composition and structure of a HMD-linked chain containing 18 glucose residues.      

Synthesis and characterization of oxidized cellulose

Samples of oxidized cellulose (OC) with various carboxyl contents and degrees of crystallinity were obtained by the oxidation of native and mercerized cellulose with a solution of nitrogen(IV) oxide in CCl₄. A detailed characterization of these OC samples was performed. The effect of oxidation conditions (concentration of N₂O₄ in the solution and oxidation time) and starting cellulose material on OC characteristics (carboxyl, carbonyl and nitrogen content, degree of crystallinity and polymerization, surface area and swelling, and acidic properties) was investigated. Reactivity in the oxidation process was higher in mercerized cellulose than in native cellulose. The action of dilute solutions (10–15%) of N₂O₄ did not affect the degree of crystallinity of cellulose samples. Under these conditions, the oxidation took place mainly in amorphous regions and on the surface of crystallites. Oxidation in a concentrated (40%) N₂O₄ solution led to the destruction of crystallites, which increased the surface area and swelling of cellulose in water. The surface area and the swelling of OC samples increased with a decrease in the index of crystallinity. The acidic properties of OC were shown to increase with an increase of swelling in water. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4785–4791, 2004     

Synthesis and characterization of nitroglycerin‐functionalized polystyrene

The synthesis and characterization of diethyl oxomalonate‐, glycerol‐, and nitroglycerin‐functionalized polystyrene (DPS, GPS, and NGPS) from polystyrene (PS) by the chemical‐modification route were explored. DPS was synthesized by the Friedel–Crafts acylation of PS with diethyl oxomalonate in the presence of SnCl₄ by a batchwise‐addition process. Proton NMR studies indicate that the acylation was essentially quantitative. IR spectroscopy was additionally used to confirm the transformation. The reduction of DPS was carried out using various reduction agents and reaction conditions. The sodium hydride reduction in tetrahydrofuran resulted in a quantitative conversion to GPS as estimated by ¹H NMR spectroscopy. Treatment of GPS with a nitrating mixture of nitric and sulfuric acids results in the formation of NGPS. All the polymers were characterized using gel permeation chromatography, IR, UV, ¹H spectroscopic techniques, pyrolysis‐mass spectrometry, and thermogravimetric analysis. This is the first investigation on the syntheses of DPS, GPS, and NGPS. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 1203–1215, 2001     

Synthesis and characterization of oligosalicylaldehyde-based epoxy resins

The synthesis of a new epoxy resin of oligosalicylaldehyde by the reaction with epichlorohydrin is reported. New resin’s epoxy value and chlorine content were determined and found to be 25% and 1%, respectively. The characterization of the new resin was instrumented by FTIR, ¹H NMR, scanning electron microscopy, and thermal gravimetric analyses. TGA results showed that the cured epoxy resin has a good resistance to thermal decomposition. The mass losses of cured epoxy resin were found to be 5%, 10%, 50% at 175°C, 240°C, and 400°C, respectively. On the curing procedure the resin was cured with polyethylenepolyamine at 25 °C for 8 h and 100°C for 1.5 h. The FTIR spectrum of new epoxy resin gave the peak of oxirane ring at ṽ = 918 cm⁻¹. In memory of Professor Dr. Adalet R. Vilayetoğlu     

Synthesis and characterization of thiocarbonohydrazone-based epoxy resins

Novel epoxy resins of various thiocarbonohydrazones have been synthesized by reacting the aldehyde or ketone derivatives of thiocarbohydrazide with excess of epichlorohydrin. The resins have been characterized by elemental analyses, epoxy equivalents, ¹H-NMR and IR spectra, thermal analyses, and viscosity measurements. Curing of the resins has been carried out by mixing with thiocarbohydrazide or ethylenediamine and heating at 80°C for 48 h. A comparison of the thermal stability of the cured resin samples has been made.     

N-硬脂酰基亮氨酸的合成

采用酰氯化反应与缩合反应两步法合成N -硬脂酰基亮氨酸。以硬脂酸和亚硫酰氯为原料 ,n(硬脂酸 )∶n(亚硫酰氯 ) =1∶1 .5 ,在 80℃下冷凝回流 6h酰氯化反应合成硬脂酰氯 ,硬脂酰氯经减压蒸馏收集 1 70～2 0 0℃的馏分得到。硬脂酰氯收率为 65 %。硬脂酰氯再与亮氨酸的氢氧化钠溶液在冰水浴中进行Schotten -Baumann缩合反应制得N -硬脂酰基亮氨酸。缩合反应最佳工艺条件是反应溶液pH值控制为 9.0。反应后滴加1mol/L盐酸至pH =5 .0～ 6.0 ,加入正己烷使N -硬脂酰基亮氨酸处于水层中 ,分离并蒸干水层溶液得含NaCl的混合物。用无水乙醇萃取混合物 ,萃取液蒸干得产物。N -硬脂酰基亮氨酸收率为 75 %     

Synthesis and characterization of microcrystalline cellulose produced from bacterial cellulose

In this study, microcrystalline cellulose (MCC) was prepared from the acid hydrolysis of bacterial cellulose (BC) produced in culture medium of static Acetobacter xylinum. The MCC-BC produced an average particle size between 70 and 90 μm and a degree of polymerization (DP) of 250. The characterization of samples was performed by thermogravimetric analysis, X-ray diffraction, and scanning electron microscopy (SEM). The MCC shows a lower thermal stability than the pristine cellulose, which was expected due to the decrease in the DP during the hydrolysis process. In addition, from X-ray diffractograms, we observed a change in the crystalline structure. The images of SEM for the BC and MCC show clear differences with modifications of BC fiber structure and production of particles with characteristics similar to commercial MCC.     

Styrylpyridine-based epoxy resins: Synthesis and characterization

Polymers containing rigid aromatic structures in the chain backbone usually gave high thermal stability and good flammability resistance. Three glycidyl ethers of epoxy resins were prepared from 2,4-di(p-hydroxystyryl)pyridine (2,4-DGESP), 2,6-di-(p-hydroxystyryl)pyridine (2,6-DGESP), and 2,4,6-tri-(p-hydroxystyryl)pryidine (2,4,6-TGESP) to study the relationships of structure to polymer degradation. To prepare a highly crosslinked material, trimethoxyboroxine (TMB) was used as the curing agent. The relative char yields of the three different resins, as measured by TGA, were 2,4-DGESP ≈ 2,6-DGESP > 2,4,6-TGESP. The char yield of the cured 2,6-DGESP varied with different amounts of the TMB curing agent, and was higher than the uncured 2,6-DGESP. The oxygen index increased as a function of thermal curing time for the 2,6-DGESP epoxy resin. An intermolecular Diels–Alder reaction with 2,6-DGESP is proposed as a primary reaction during thermal curing.     

Synthesis and characterization of isotopically enriched methylmercury (CH3201Hg+)

A simple procedure for the synthesis of an important standard, isotopically enriched methylmercury, which is not commercially available, has been established successfully. The isotopically enriched standard synthesized is utilized in conventional isotope dilution mass spectrometry (IDMS), as well as in speciated IDMS (SIDMS), for determination of the true concentration of methylmercury in environmental samples. The CH₃²⁰¹Hg⁺ standard has been synthesized from commercially available ²⁰¹HgO and tetramethyltin. The synthesis time required is 1 h at 60°C. The product is highly pure, yielding more than 90% as ²⁰¹Hg in CH₃²⁰¹Hg⁺. Hazardous dimethylmercury does not occur during this synthesis procedure. The product synthesized was analyzed using high‐performance liquid chromatography coupled with inductively coupled plasma mass spectrometry (ICP‐MS) and ICP‐MS alone in order to determine its concentration, isotopic composition and purity. The stability of the product was also evaluated for over 6 months and found to be stable at 4°C in the dark. The isotopically enriched methylmercury synthesized can be used in SIDMS and IDMS analyses as a standard. Copyright © 2003 John Wiley & Sons, Ltd.     

Synthesis and characterization of hyperbranched polyurethane-urea coatings

A series of hyperbranched polyurethane (HBPU)-urea coatings were synthesized by a systematic two-step reaction process. Initially, isocyanate terminated PU prepolymers were prepared from a hyperbranched polyester polyols with isophorone diisocyanate at NCO/OH ratio of 1.6:1 for 5 h at 70-80 °C. The excess NCO content after the synthesis of NCO terminated HBPU prepolymer was completely reacted with atmospheric moisture. The obtained HBPU-urea networks were characterized with Fourier transform-infrared (FT-IR) spectroscopy for the quantitative evolution of the extent of urethane and urea bonds as well as to study the structure-property relationship. In order to find out the changes and types of intermolecular H-bonding interaction in the HBPU-urea films with the variation in polyester structure, the deconvolution of FT-IR spectra were carried out using Origin 6.0 software through Gaussian curve-fitting method. The viscoelastic properties and thermal stability of the synthesized coatings were determined by dynamic mechanical and thermal analyzer and thermogravimetric analyzer, respectively. For HBPU-urea samples glass transition temperature and thermal stability increased with the generation number from the first to the third. Polyester samples showed single step decomposition profile and HBPU-urea samples showed two-steps decomposition with good thermal stability.     

Structural characterization of glycoporphyrins by electrospray tandem mass spectrometry

Porphyrin derivatives having a galactose or a bis(isopropylidene)galactose structural unit, linked by ester or ether bonds, were characterized by electrospray tandem mass spectrometry (ES-MS/MS). The electrospray mass spectra of these glycoporphyrins show the corresponding [M + H](+) ions. For the glycoporphyrins with pyridyl substituents and those having a tetrafluorophenyl spacer, the doubly charged ions [M + 2H](2+) were also observed in ES-MS with high relative abundance. The fragmentation of both [M + H](+) and [M + 2H](2+) ions exhibited common fragmentation pathways for porphyrins with the same sugar residue, independently of the porphyrin structural unit and type of linkage. ES-MS/MS of the [M + H](+) ions of the galactose-substituted porphyrins gave the fragment ions [M + H - C(2)H(4)O(2)](+), [M + H - C(3)H(6)O(3)](+), [M + H - C(4)H(8)O(4)](+) and [M + H - galactose residue](+). The fragmentation of the [M + 2H](2+) ions of the porphyrins with galactose shows the common doubly charged fragment ions [porphyrin + H](2+), [M + 2H - C(2)H(4)O(2)](2+), [M + 2H - C(4)H(8)O(4)](2+), [M + 2H - galactose residue](2+) and the singly charged fragment ions [M + H - C(3)H(6)O(3)](+) and [M + H - galactose residue](+). The fragmentation of the [M + H](+) ions of glycoporphyrins with a protected galactosyl residue leads mainly to the ions [M + H - CO(CH(3))(2)](+), [M + H - 2CO(CH(3))(2)](+), [M + H - 2CO(CH(3))(2) - CO](+), [M + H - C(10)H(16)O(4)](+) and [M + H - protected galactose](+). The doubly charged ions [M + 2H](2+) fragment to give the doubly charged ions [porphyrin + H](2+) and the singly charged ions [M + H - protected galactose residue](+) and [M + H - CO(CH(3))(2)](+). For the porphyrins where the sugar structural unit is linked by an ester bond, [M + 2H](2+), ES-MS/MS showed a major and typical fragmentation corresponding to combined loss of a sugar structural unit and further loss of water, leading to the ion [M + 2H - sugar residue - H(2)O](2+), independently of the structure of the sugar structural unit. These results show that ES-MS/MS can be a powerful tool for the characterization of the sugar structural unit of glycoporphyrins, without the need for chemical hydrolysis.