CuO-ZnO-ZrO2催化甲醇水蒸汽重整反应机理和中间态

应用质谱在线技术,对CuO-ZnO-ZrO2催化甲醇水蒸汽重整（SRM）反应进行程序升温脱附（TPD）和程序升温表面反应（TPSR）研究.结果表明:在反应态催化剂表面,甲醇以分子吸附态形式存在,甲醇水蒸汽重整反应经历甲酸根中间物种.分别用CuO、CuO-ZnO、CuO-ZnO-ZrO2作催化剂,甲醇在气流中的摩尔分数分别高于5.4％、0.37％和0.17％时,甲酸根中间态的分解产物为CO2和H2;而甲醇在气流中的摩尔分数分别低于5.4％、0.37％和0.17％时,甲酸根中间态的分解产物为CO、CO2和H2.     

CuO-ZnO-ZrO_2催化甲醇水蒸汽重整反应机理和中间态

应用质谱在线技术,对CuO-ZnO-ZrO2催化甲醇水蒸汽重整(SRM)反应进行程序升温脱附(TPD)和程序升温表面反应(TPSR)研究.结果表明:在反应态催化剂表面,甲醇以分子吸附态形式存在,甲醇水蒸汽重整反应经历甲酸根中间物种.分别用CuO、CuO-ZnO、CuO-ZnO-ZrO2作催化剂,甲醇在气流中的摩尔分数分别高于5.4%、0.37%和0.17%时,甲酸根中间态的分解产物为CO2和H2;而甲醇在气流中的摩尔分数分别低于5.4%、0.37%和0.17%时,甲酸根中间态的分解产物为CO、CO2和H2.     

Ni-K/Al_2O_3系催化剂上甲醇分解的红外光谱研究

用红外光谱技术研究了室温至300℃时甲醇在Ni-K/Al_2O_3系催化剂上分解形成的吸附态。在Ni/Al_2O_3上形成了物理吸附甲醇、表面甲氧基、吸附一氧化碳和表面甲酸盐。除此以外,在Ni-K/Al_2O_3上还形成了一个稳定的一氧化碳吸附构型及表面碳酸氢盐和=配位碳酸盐。各种表面生成物的稳定性和生成量与催化剂中1K含量及温度之间的关系密切。另外,讨论了甲醇分解时在Ni-K/Al_2O_3系催化剂表面上发生的反应,确认甲醇分解的中间反应产物是表面甲氧基。     

甲醇在活性Al2O3催化剂表面的吸附与脱水反应

 采用X射线衍射、红外光谱、程序升温脱附和微反等技术对一系列不同方法制备的活性Al2O3催化剂的结构和性能进行了表征,探讨了催化剂的结构与甲醇脱水反应性能之间的构效关系,提出了甲醇在活性Al2O3催化剂表面脱水的反应机理. 结果表明,活性Al2O3主要由γ-Al2O3和无定形的Al2O3组成,其表面存在σⅠ和σⅡ两种L酸吸附位. 甲醇在Al2O3表面有两种吸附态,即分子吸附态和解离吸附态,其中甲醇的分子吸附为可逆吸附,而解离吸附态甲醇(即甲氧基)在催化剂表面解离成表面甲氧基和羟基,当反应温度较高时,表面甲氧基会进一步分解产生CO,H2以及少量的CO2,CH4和C等. 二甲醚的生成是分子吸附态甲醇与临近的解离吸附态甲醇相互作用的结果.     

乙烯和乙烷在CeO_2上温和条件下表面氧化反应的原位FT-IR研究

本文用原位FT-IR研究了CeO_2上O_2、C_2H_4和C_2H_6的吸附以及C_2H_4和C_2H_6的氧化反应。室温下吸附O_2后在CeO_2表面上形成超氧物种(O_2~-),吸附C_2H_4后在990cm~(-1)处检测到红外峰,归属为吸附C_2H_4与表面晶格氧形成的C-O键的振动频率。这些吸附物种在高于100℃时消失。室温下C_2H_6在CeO_2表面上未形成吸附态。C_2H_4在CeO_2表面上60℃即可发生氧化反应。在300℃以下,C_2H_4氧化后表面上主要形成甲酸根物种。当高于300℃时表面上主要是深度氧化的产物碳酸基物种。C_2H_6在CeO_2表面上200℃始被氧化为甲酸根物种,高于300℃时,表面上也主要形成碳酸基物种。在气相O_2存在下也得到与上述相同的结果。讨论了C_2H_4和C_2H_6的表面氧化机理以及表面氧物种的作用,认为在低于300℃时,参与C_2H_4和C_2H_6氧化的氧物种主要是表面晶格氧,超氧吸附物种可能在高于300℃时才参与反应。     

甲醇在CeO2担载Pd催化剂上分解机理的研究

采用原位红外(in-situFTIR)技术对甲醇在CeO₂和Pd/CeO₂催化剂上的吸附和反应进行了研究,提出一个新的甲醇分解反应机理模型.甲醇在CeO₂上容易吸附并结合其晶格氧生成甲酸盐物种,而甲醇分解的产物氢被Pd活化后,溢流到CeO₂上促进了甲酸盐物种的分解.Cl^-的存在加强了Pd/CeO₂催化剂与氢的相互作用,Pd和CeO₂通过对氢和氧物种的作用对甲醇分解反应的过程表现出协同效应.     

ZrO2催化剂上吸附CH3NO2的分解

用TPD和IR谱研究了CH_3NO_2在ZrO_2催化剂上的吸附活化和分解反应。结果表明,室温下CH_3NO_2在ZrO_2表面发生不可逆化学吸附,它们在TPD过程中可完全分解生成HCN、CO_2、CO、NH_3、H_2O和微量NO。其中H_2O和NO的脱附峰出现在383K附近。其它产物在543K附近出现极大值。IR结果表明,CH_3NO_2在ZrO_2上吸附形成诸如[CH_2NO_2],和/或吸附物种。这些吸附物种在升高温度时转化为表面态“HCN”。“HCN”或脱附,或进一步向表面“HCONH_2”和/或“HCOO~-”转化,后两种表面物种分解可产生CO_2、NH_3和CO。将这些结果与CH_3NO_2在SiO_2-Al_O_3和MgO催化剂上的结果进行了比较,讨论了酸-碱双功能性ZrO_2催化剂上CH_3NO_2活化分解的特点。     

ZrO2催化剂上吸附甲酸的TPD和IR研究

众多的研究表明甲酸在氧化物催化剂上的吸附分解与催化剂的表面酸碱性质有关。研究吸附相甲酸物种的变化表明甲酸分解反应的选择性除受温度影响外,还与甲酸的表面覆盖度有关。Z_rO_2表现为较典型的弱酸弱碱双功能性催化剂。最近我们的研究表明Z_rO_2表面存在表面键诱导酸-碱相互作用,它的酸-碱双功能催化作用在烷基胺分解转化为腈的反应中得到了较好地体现。本文报导Z_rO_2催化剂上吸附甲酸的程序升温脱附(TPD)和红外光谱(IR)研究结果。     

Pd/α-Al2O3催化CO偶联制草酸二甲酯的反应机理

采用傅里叶变换红外光谱对Pd/α-Al2O3催化剂上CO偶联制草酸二甲酯的反应机理进行了研究.通过改变原料气CO和亚硝酸甲酯进入原位反应池的顺序,使反应过程更加直观.实验结果表明,CO偶联反应发生在桥式吸附态的CO和气相的亚硝酸甲酯之间,CO的吸附为反应的控制步骤.亚硝酸甲酯在Pd/α-Al2O3上易分解,生成甲醇、甲醛和甲酸甲酯.在反应初期使CO先在催化剂表面吸附饱和,可以有效控制该分解反应的进行.     

甲酸在Au(997)台阶表面的氧化反应（英文）

金催化是纳米催化的代表性体系之一,但对金催化作用的理解还存在争议,特别是金颗粒尺寸对其催化作用的影响.金颗粒尺寸减小导致的表面结构主要变化之一是表面配位不饱和金原子密度的增加,因此研究金原子配位结构对其催化作用的影响对于理解金催化作用尺寸依赖性具有重要意义.具有不同配位结构的金颗粒表面可以利用金台阶单晶表面来模拟.我们研究组以同时具有Au(111)平台和Au(111)台阶的Au(997)台阶表面为模型表面,发现Au(111)台阶原子在CO氧化、NO氧化和NO分解反应中表现出与Au(111)平台原子不同的催化性能.负载型Au颗粒催化甲酸氧化反应是重要的Au催化反应之一.本文利用程序升温脱附/反应谱(TDS/TPRS)和X射线光电子能谱(XPS)研究了甲酸在清洁的和原子氧覆盖的Au(997)表面的吸附和氧化反应,观察到Au(111)台阶原子和Au(111)平台原子不同的催化甲酸根氧化反应行为.与甲酸根强相互作用的Au(111)台阶原子表现出比与甲酸根弱相互作用的Au(111)平台原子更高的催化甲酸根与原子氧发生氧化反应的反应活化能.在清洁Au(997)表面,甲酸分子发生可逆的分子吸附和脱附.甲酸分子在Au(111)台阶原子的吸附强于在Au(111)平台原子的吸附.TDS结果表明,吸附在Au(111)台阶原子的甲酸分子的脱附温度在190 K,吸附在Au(111)平台原子的甲酸分子的脱附温度在170 K.XPS结果表明,分子吸附甲酸的C 1s和O 1s结合能分别位于289.1和532.8 e V.利用多层NO_2的分解反应在Au(997)表面控制制备具有不同原子氧吸附位和覆盖度的原子氧覆盖Au(997)表面,包括氧原子吸附在(111)台阶位的0.02 ML-O(a)/Au(997)、氧原子同时吸附在(111)台阶位和(111)平台位的0.12 ML-O(a)/Au(997)、氧原子和氧岛吸附在(111)平台位和氧原子吸附在(111)台阶位的0.26 ML-O(a)/Au(997).TPRS和XPS结果表明,甲酸分子在105 K与Au(997)表面原子氧物种反应生成甲酸根和羟基物种,但甲酸根物种的进一步氧化反应依赖于Au原子配位结构和各种表面物种的相对覆盖度.在0.02 ML-O(a)/Au(997)表面暴露0.5 L甲酸时,Au(111)台阶位氧原子完全反应,甲酸过量.表面物种是Au(111)台阶位吸附的甲酸根、羟基和甲酸分子.在加热过程中,甲酸分子与羟基在181 K反应生成甲酸根和气相水分子(HCOOH(a)+OH(a)=H_2O+HCOO(a)),甲酸根在340 K发生歧化反应生成气相HCOOH和CO_2分子(2HCOO(a)=CO_2+HCOOH).在0.12 ML-O(a)/Au(997)和0.26 ML-O(a)/Au(997)表面暴露0.5 L甲酸时,甲酸分子完全反应,原子氧过量.表面物种是Au(111)平台位和Au(111)台阶位吸附的甲酸根、羟基和原子氧.在加热过程中,Au(111)平台位和Au(111)台阶位的甲酸根分别在309和340 K同时发生氧化反应(HCOO(a)+O(a)=H_2O+CO_2)和歧化反应(2HCOO(a)=CO_2+HCOOH)生成气相CO_2,H_2O和HCOOH分子.在0.26 ML-O(a)/Au(997)表面暴露10 L甲酸时,甲酸分子和原子氧均未完全消耗.表面物种是Au(111)平台位和Au(111)台阶位吸附的甲酸根、羟基、甲酸分子和原子氧.在加热过程中,除了上述甲酸根的氧化反应和歧化反应,还发生171 K的甲酸分子与羟基的反应(HCOOH(a)+OH(a)=H_2O+HCOO(a))和216 K的羟基并和反应(OH(a)+OH(a)=H_2O+O(a)).     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.