纳米二氧化钛的制备及其光催化性能

分别采用水热法和溶胶-凝胶法制备了TiO2纳米粉体;利用X射线衍射仪和扫描电镜分析了两种方法制备的TiO2粉体的形貌和晶体结构,并测定了纳米TiO2粉体对罗丹明B的光催化降解活性.结果表明:采用水热法制备的TiO2纳米粉体含有锐钛矿相和金红石相,粒径较小,大约为50nm,而且分散均匀,光催化性能良好;采用溶胶-凝胶法制备的TiO2粉体经过550℃煅烧后仍然为锐钛矿相,而且粒径较大,大约为80nm.     

Structural evolution of self-expanding arrays of charged particulates

Self-expansion patterns of unconstrained assemblies of charged particulates are simulated by solution of their individual trajectories. The general behaviour of these systems is considered regarding their expansion shape and structure. As the particulates cannot be described, in general, in terms of massless charged entities, the complete equation of motion, inclusive of the inertial and other size effects, must be applied to each and every member of the assembly. It is shown that irrespective of the initial position of the particulates and the time dependent shape of the assembly, when expanding in free space or else the particulates are identical in size, shape and mass, they self-expand asymptotically into a circular or spherical shape with an inner structure that tends to uniformity. This behaviour persists irrespective of the size and charge level of the particulates, or whether they form a single or multiple separate groups in one, two and three dimensions. In this context, ionic gaseous assemblies that fit into the realm of continua, are included. Two- and three-dimensional examples of simulation outputs for different particulate assemblies, illustrate typical self-expansion patterns. Internal structures that evolve in two-dimensional self-expanding arrays are shown to be different compared to those obtained in three dimensions. These simulations show that models of particle capture by random self-expanding arrays of charged particulates, may lack physical grounds, as they contradict the asymptotic mode of uniform and ordered self-expansion that is expected from the array.     

Determination of lead in fine particulates by slurry sampling electrothermal atomic absorption spectrometry

A simple method for determining lead in fine particulates (PM2.5) by using electrothermal atomic absorption spectrometry (ETAAS) has been developed. Particulates collected on Nuclepore filter by using a dichotomous sampler were suspended in diluted nitric acid after ultrasonic agitation. The dislodging efficiency is nearly 100% after agitation for 5 min. In order to study the suspension behavior of PM2.5 in solvents, a Brookhaven ZetaPlus Particle Size Analyzer was used to determine the particle size distribution and suspension behavior of air particulates in the solvent. The pre-digestion and modification effect of nitric acid would be discussed. Palladium was added as a chemical modifier and the temperature program of ETAAS was changed in order to improve the recovery. The slurry was introduced directly into a graphite tube for atomization. The metal content in the sample was determined by the standard addition method. In addition, a conventional acid digestion procedure was applied to verify the efficiency of the slurry sampling method. It offers a quick and efficient alternative method for heavy metal characterization in fine particulates.     

Size, morphology and composition of particulates in aquatic ecosystems: solving speciation problems by correlative electron microscopy.

Particulates can impact directly on aquatic ecosystems by determining the availability and mode of dispersion of both contaminants and nutrients. An understanding of the mechanisms of such particle-associated phenomena is being augmented by particle analysis technology. In this context, microscopic and spectroscopic techniques, devised for problem solving, are being applied to frequently encountered sub-micrometre particulates which are 'unstable' with respect to methods of sample preparation and storage used routinely for particulates prior to analysis. These unstable aquatic particulates include 'species' sensitive to dehydration and to artificial aggregation induced by surfaces within a fractionation apparatus. These species, as defined broadly, include polysaccharide gels, hydrated humic substances, iron oxyhydroxides, viruses, the smallest micro-organisms and decomposing parts of cells. To develop predictive models of their roles as dispersing agents for contaminants, and to speciate such associations, it is necessary to characterize them in a state as close to the natural as possible. This critical review presents the state-of-the-art in the realistic characterization of hydrated sub-micrometre particulates by correlative electron microscopy (EM) used in conjunction with spectroscopy and minimally perturbing preparatory techniques. Correlative EM is a strategy for using several different kinds of microscopes and accessory techniques in a multi-method context to analyse a given specimen for different kinds of information, including relationships in three dimensions within colloid systems. Sizing, morphology and gross composition are determined on a 'per particle' basis by transmission EM used in conjunction with energy-dispersive spectroscopy, electron diffraction and molecule-specific stains.(ABSTRACT TRUNCATED AT 250 WORDS)     

Effect of microfibril twisting on theoretical powder diffraction patterns of cellulose Iβ

Previous studies of calculated diffraction patterns for cellulose crystallites suggest that distortions that arise once models have been subjected to molecular dynamics (MD) simulation are the result of both microfibril twisting and changes in unit cell dimensions induced by the empirical force field; to date, it has not been possible to separate the individual contributions of these effects. To provide a better understanding of how twisting manifests in diffraction data, the present study demonstrates a method for generating twisted and linear cellulose structures that can be compared without the bias of dimensional changes, allowing assessment of the impact of twisting alone. Analysis of unit cell dimensions, microfibril volume, hydrogen bond patterns, glycosidic torsion angles, and hydroxymethyl group orientations confirmed that the twisted and linear structures collected with this method were internally consistent, and theoretical powder diffraction patterns for the two were shown to be effectively indistinguishable. These results indicate that differences between calculated patterns for the crystal coordinates and twisted structures from MD simulation can result entirely from changes in unit cell dimensions, and not from microfibril twisting. Although powder diffraction patterns for models in the 81-chain size regime were shown to be unaffected by twisting, suggesting that a modest degree of twist is not inconsistent with available crystallographic data, it may be that other diffraction techniques are capable of detecting this structural difference. Until such time as definitive experimental evidence comes to light, the results of this study suggest that both twisted and linear microfibrils may represent an appropriate model for cellulose Iβ.     

Effect of violations of the structure and layer packing on the diffraction pattern of gibbsite and bayerite

Using the simulation method for the diffraction patterns of one-dimensionally disordered materials, the effect of different violations in the layered structure of aluminum trihydroxides (gibbsite and bayerite) on their diffraction patterns is analyzed. The features of the diffraction patterns of a disordered gibbsite sample obtained by intercalation-deintercalation of lithium salts are considered.     

Determination of hydroxylated polycyclic aromatic hydrocarbons in airborne particulates by high-performance liquid chromatography with fluorescence detection.

This paper describes a highly sensitive and selective method for the determination of hydroxylated polycyclic aromatic hydrocarbons (PAHs-OH) in airborne particulates. PAHs-OH were extracted from airborne particulates with ethanol by ultrasonication. The extractant was further cleaned up by solid phase extraction (SPE) with an aminopropylsilica cartridge, and subsequently analyzed by reversed-phase high-performance liquid chromatography with fluorescence detection. 2-Hydroxy-1-acetonaphthone was used as an internal standard. By the proposed method, 2-hydroxyfluorene and 1-hydroxypyrene were identified in airborne particulates and their concentrations were determined for the first time.     

Determination of lead in fine particulates by slurry sampling electrothermal atomic absorption spectrometry

A simple method for determining lead in fine particulates (PM_2.5) by using electrothermal atomic absorption spectrometry (ETAAS) has been developed. Particulates collected on Nuclepore filter by using a dichotomous sampler were suspended in diluted nitric acid after ultrasonic agitation. The dislodging efficiency is nearly 100% after agitation for 5 min. In order to study the suspension behavior of PM_2.5 in solvents, a Brookhaven ZetaPlus Particle Size Analyzer was used to determine the particle size distribution and suspension behavior of air particulates in the solvent. The pre-digestion and modification effect of nitric acid would be discussed. Palladium was added as a chemical modifier and the temperature program of ETAAS was changed in order to improve the recovery. The slurry was introduced directly into a graphite tube for atomization. The metal content in the sample was determined by the standard addition method. In addition, a conventional acid digestion procedure was applied to verify the efficiency of the slurry sampling method. It offers a quick and efficient alternative method for heavy metal characterization in fine particulates. Received: 2 August 2000 / Revised: 25 October 2000 / Accepted: 28 October 2000     

Simulation and interpretation of 2D diffraction patterns from self-assembled nanostructured films at arbitrary angles of incidence: from grazing incidence (above the critical angle) to transmission perpendicular to the substrate

A method to calculate the location of all Bragg diffraction peaks from nanostructured thin films for arbitrary angles of incidence from just above the critical angle to transmission perpendicular to the film is reported. At grazing angles, the positions are calculated using the distorted wave Born approximation (DWBA), whereas for larger angles where the diffracted beams are transmitted though the substrate, the Born approximation (BA) is used. This method has been incorporated into simulation code (called NANOCELL) and may be used to overlay simulated spot patterns directly onto two-dimensional (2D) grazing angle of incidence small-angle X-ray scattering (GISAXS) patterns and 2D SAXS patterns. The GISAXS simulations are limited to the case where the angle of incidence is greater than the critical angle (alpha(i) > alpha(c)) and the diffraction occurs above the critical angle (alpha(f) > alpha(c)). For cases of surfactant self-assembled films, the limitations are not restrictive because, typically, the critical angle is around 0.2 degrees but the largest d spacings occur around 0.8 degrees 2theta. For these materials, one finds that the DWBA predicts that the spot positions from the transmitted main beam deviate only slightly from the BA and only for diffraction peaks close the critical angle. Additional diffraction peaks from the reflected main beam are observed in GISAXS geometry but are much less intense. Using these simulations, 2D spot patterns may be used to identify space group, identify the orientation, and quantitatively fit the lattice constants for SAXS data from any angle of incidence. Characteristic patterns for 2D GISAXS and 2D low-angle transmission SAXS patterns are generated for the most common thin film structures, and as a result, GISAXS and SAXS patterns that were previously difficult to interpret are now relatively straightforward. The simulation code (NANOCELL) is written in Mathematica and is available from the author upon request.     

The microdetection of organoparticulates from diazonium compounds

The thermal decompositions of a series of diazonium compounds have been investigated using the new technique of organic particulate analyses (OPA). This extremely sensitive technique makes possible the detection of particulates emitted from the diazonium compounds during thermal decomposition. The submicron particulates derived in this fashion are readily detectable by their influence on the output current of an ion chamber detector or by their effect on the cloud chamber of a condensation nuclei monitor.Of the 14 diazonium compounds evaluated, 11 were found to exhibit particulation behavior below 190 °C. In some cases, very strong particulation was detectable. No apparent correlation between the organic particulation temperature range (OPTR) and their literature thermal decomposition temperatures was evident. Efforts were made to characterize the nature of the particulates using mass spectrometry but this was hampered by the extreme complexities of the spectral patterns.In terms of their abilities to produce particulates, the diazonium compounds can be placed in four main groups reflecting their chemical composition, molecular size, and degree of substitution. Vapor phase association of the molecular fragments formed during thermal decomposition might be occurring to produce the required particulate size detectable by the present instrumentation.     

The determination of lead in total suspended air particulates by x-ray fluorescence spectroscopy

A method has been developed for the measurement of lead in air particulates collected on glass fiber filter paper with wavelength-dispersive x-ray fluorescence spectroscopy (WDXRF). Analyses conducted by both WDXRF and an EPA-approved procedure that employs acid sonication followed by analysis of the extract by atomic-absorption spectroscopy (AAS) shows excellent agreement between the two methods. WDXRF calibration was accomplished with standards prepared from known additions of Pb to unexposed glass fiber filter discs. Method equivalency has also been demonstrated by the analysis of several reference materials and the statistical analysis of quality control data. The WDXRF procedure has also been used to evaluate the distribution of Pb in the particulates across the surface of the filter.     

Fifty Years of Gas-Phase Electron-Diffraction Structure Research: A Personal Retrospective

The author has spent nearly five decades working on the molecular structure of gaseous molecules using principally the method of electron diffraction. During this time he has seen and participated in the development of the method from its crude beginning in which the diffraction patterns were measured by hand and interpreted by eye, to the powerful, nearly automatic instrument-based methods of today. Accompanying this evolution in the method is a similar evolution in the complexity of the scientific problems. Whereas in the early days the molecules studied were necessarily simple and the parameter determinations accurate to a few hundredths of an Ångström, electron diffraction today is routinely applied to molecules with a 10-fold greater numbers of parameters and yields results 10 times more accurate. This article summarizes some of the many recollections accumulated by the author during that professional journey.     

X-ray diffraction analysis of ultradisperse systems: The Debye formula

Problems of X-ray diffraction analysis of ultradisperse systems with the particle size up to 5 nm are discussed in the review. A method for calculating X-ray diffraction patterns using the Debye formula within the kinematic theory of X-ray scattering (Debye Function Analysis-DFA) is presented. The DFA method makes it possible to obtain information on the atomic structure, shape and size of nanoparticles, and verify hypotheses on the presence of deformations, stacking faults and other structural features of ultradisperse and nanostructured systems. The method is applicable for modeling the diffraction patterns of objects with an arbitrary (not necessarily crystal) structure. Applications of the method for examining the structure of various objects are discussed.     

色谱质谱中的选择离子监测方式定量分析柴油机排气微粒中多环芳香烃

使用色谱－质谱联用中的选择离子监测的方法选择性地检测柴油机排气中的多环芳香烃,采用１４种多环芳香烃混合标准样品绘制校正曲线,以外标法对柴油机排气微粒中的ＰＡＨｓ进行定量分析。实验结果表明,该方法能够减少其它类有机成份的干扰,快速、准确地测量柴油机排气微粒中多环芳香烃的含量,且重复性较好,相对标准偏差低于 １２％（ｎ＝６）,检出限为３．５～７．０ｐｇ／ｍ３,样品的回收率为７９％～８９％,方法用于柴油机排气微粒中多环芳香烃排放量的测定取得了满意的效果。     

X-Ray Structural Analysis of Human Serum

The structure of human serum was studied by X-ray diffraction method and the patterns were referred to those of pure water. For two groups of serum samples, the patterns differed significantly from those of pure water. One of the distinguished groups came from people suffering from neoplasmic diseases - the samples were studied directly after centrifugation. The other distinguished group included the samples studied after precipitation of proteins. The results obtained confirmed the earlier supposition that the dominant interactions in water low-concentration solutions of proteins in the serum of healthy people are those between water molecules and non-polar chains of side amino acids. For the samples of serum with precipitated proteins or obtained from hemolysed blood, the diffraction pattern shows a sharp maximum, testifying to the formation of a significant number of water-ion complexes disturbing the structure of pure water. The results have confirmed a possibility of using serum diffraction patterns as a diagnostic tool.     

典型煤灰成分细颗粒物在过饱和水汽环境中的长大特性

实验采用专门针对液滴的滴谱仪作为测量工具,以典型煤灰成分细颗粒物石英、氧化铁、莫来石、硫酸钙为研究对象,在热水与冷空气接触形成的低过饱和度下进行了蒸汽异相凝结长大实验研究。考察了颗粒润湿性、粒径以及热水温度对颗粒长大效果的影响。结果表明,润湿性好的颗粒长大效果好,初始粒径越小的颗粒长大倍数越大;热水温度对颗粒长大影响非常明显,热水温度越高,颗粒越容易发生异相凝结,颗粒最终直径越大。     

Solid phases of cyclopentane: combined experimental and simulation study

The phase diagram of cyclopentane has been studied by powder neutron diffraction, providing diffraction patterns for phases I, II, and III, over a range of temperatures and pressures. The putative phase IV was not observed. The structure of the ordered phase III has been solved by single-crystal diffraction. Computational modeling reveals that there are many equienergetic ordered structures for cyclopentane within a small energy range. Molecular dynamics simulations reproduce the structures and diffraction patterns for phases I and III and also show an intermediate disordered phase, which is used to interpret phase II.     

硒/氧化石墨烯/二氧化钛复合薄膜的制备及光电转换性质

将氧化石墨烯(GO)掺入钛酸溶胶中,以导电玻璃(ITO)为基底,经浸渍-涂覆-煅烧得到GO/TiO2复合薄膜;采用电沉积技术在GO/TiO2薄膜表面沉积Se纳米微粒,得到Se/GO/TiO2复合薄膜;利用扫描电子显微镜和X射线衍射仪分析了复合薄膜的形貌和晶体结构,采用紫外可见光谱仪测定了其光谱学性质,利用光电转换实验测定了其光电转换性质.结果表明,所制备的Se/GO/TiO2复合薄膜各组分分布均匀,具有锐钛矿相结构的TiO2颗粒粒径为20nm,与TiO2结合的GO具有分散片层结构,薄膜中的Se颗粒粒径为60～80nm.与此同时,在Se和GO的共同作用下,Se/GO/TiO2复合薄膜对可见光有很好的光电转换效应.     

沉淀法制备CeO2纳米晶与表征

采用乙醇为分散剂和保护剂,用反向沉淀法制备了不同粒径的CeO2纳米晶。XRD分析表明,当焙烧温度为250－800℃时,所合成的CeO2纳米粒子属于立方晶系,空间群为OH^5-FM3M。TEM分析表明,CeO2纳米粒子呈球形,粒度随焙烧温度的增加而增大。热失重分析表明样品的热失重主要受温度的影响,而焙烧时间的影响不大。相对密度分析表明,随CeO2纳米晶粒度的增大,粉末的密度增加。     

大气颗粒物化学组成分析

大气颗粒物的化学组成非常复杂,其中包括大量矿质氧化物、可溶性硫酸盐、硝酸盐、海盐、多环芳烃、有机酸和有机氟等。大气颗粒物对局地、区域甚至全球大气辐射平衡、大气能见度、元素的生物化学循环具有重要影响,危害人体健康并参与大气非均相反应。化学组成是决定大气颗粒物各种环境效应的关键因素。国内外对大气颗粒物化学组成分析进行了大量的研究工作。特别是随着气动力学透镜的发展与应用,结合快速、灵敏的光谱和质谱检测手段,适合大气颗粒物化学组成的在线分析方法取得了较大的突破。