Preparation,characterization and application of a new 25,27‐bis‐[2‐(5‐methylthiadiazole)thioethoxyl]‐26,28‐dihydroxy‐para‐tert‐butyl calix[4]arene stationary phase for HPLC

A new para‐tert‐butylcalix[4]arene column containing thiadiazole functional groups was prepared and used for the separation of polycyclic aromatic hydrocarbons, phenolic compounds, aromatic amines, benzoic acid and its derivatives by high‐performance liquid chromatography (HPLC). The effect of organic modifier content in the mobile phase on retention and selectivity of these compounds were investigated. The results indicate that the stationary phase behaves like reversed‐phase packing. However, hydrogen bonding, π–π and inclusion interactions seem to be involved in the separation process. The column has been successfully employed for the analysis of clenbuterol in pork and pig casing; the limit of detection and the limit of quantitation for this method by HPLC‐UV detection was 0.03 and 0.097 μg/mL, respectively; the method is demonstrated to be suitable and a competitive alternative analytical method for the determination of clenbuterol.     

Epoxide‐derived mixed‐mode chromatographic stationary phases for separation of active substances in fixed‐dose combination drugs

A method for the preparation of novel mixed‐mode reversed‐phase/strong cation exchange stationary phase for the separation of fixed‐dose combination drugs has been developed. An epoxysilane bonded silica prepared by vapor phase deposition was used as a starting material to produce diol, octadecyl, sulfonate, and mixed octadecyl/sulfonate groups bonded silica phases. The chemical structure and surface coverage of the functional groups on these synthesized phases were confirmed by fourier‐transform infrared and solid‐state ¹³C NMR spectroscopy and elemental analysis. Alkylbenzene homologs, basic drugs, nucleobases and alkylaniline homologs were used as probes to demonstrate the reversed‐phase, ion exchange, hydrophilic interaction and mixed‐mode retention behaviors of these stationary phases. The octadecyl/sulfonate bonded silica exhibits pronounced mixed‐mode retention behavior and superior retentivity and selectivity for alkylaniline homologs. The mixed‐mode retention is affected by either ionic or solvent strength in the mobile phase, permiting optimization of a separation by fine tuning these parameters. The mixed‐mode stationary phase was applied to separate two fixed‐dose combination drugs: compound reserpine tablets and compound methoxyphenamine capsules. The results show that simultaneous separation of multiple substances in the compound dosage can be achieved on the mixed‐mode phase, which makes multi‐cycles of analysis for multiple components obsolete.     

Preparation and Characterization of a New Quercetin‐bonded Stationary Phase for High Performance Liquid Chromatography

A quercetin‐bonded silica gel stationary phase (QUSP) containing natural flavonoid ligand was first prepared via γ‐glycidoxypropyltrimethoxysilane (KH‐560) as a coupling reagent for high‐performance liquid chromatography. Its chemical structure was characterized by Fourier infrared spectroscopy, elemental analysis, thermal thermogravimetry and ¹³C cross polarization/magic angle spinning nuclear magnetic resonance (CP/MAS NMR). The chromatographic property of QUSP was systematically evaluated by using neutral, basic and acidic aromatic compounds as probes. In order to clarify its retention mechanism, a comparative study of QUSP with conventional octadecylsilyl‐bonded stationary phase (ODS) was also carried out under the same conditions. The results showed that the new quercetin‐bonded phase exhibited an excellent reversed‐phase chromatographic property with relatively weak hydrophobicity. However, it has an advantage over ODS in the fast separation of polar aromatic compounds because the quercetin ligand could provide various sites besides hydrophobicity, such as hydrogen bonding, dipole‐dipole, π‐π staking and charge transfer interactions. QUSP was performed in the baseline separations of ionized polar basic or acidic compounds, including pyridines, anilines, pyrimidines, purines and phenols with symmetric peak shape in common mobile phases without buffer salt within relatively short time. The natural ligands from herbs are readily available and contain a variety of active sites, which facilitate the exploration of industrial chromatographic separation materials for green products.     

New zwitterionic polymethacrylate monolithic columns for one‐ and two‐dimensional microliquid chromatography

We prepared 0.53 and 0.32 mm id monolithic microcolumns by in situ copolymerization of a zwitterionic sulfobetaine functional monomer with bisphenol A glycerolate dimethacrylate (BIGDMA) and dioxyethylene dimetacrylate crosslinkers. The columns show a dual retention mechanism (hydrophilic‐interaction mode) in acetonitrile‐rich mobile phases and RP in highly aqueous mobile phases. The new 0.53 mm id columns provided excellent reproducibility, retention, and separation selectivity for phenolic acids and flavonoids. The new zwitterionic monolithic columns are highly orthogonal, with respect to alkyl silica stationary phases, not only in the hydrophilic‐interaction mode but also in the RP mode. The optimized monolithic zwitterionic microcolumn of 0.53 mm id was employed in the first dimension, either in the aqueous normal‐phase or in the RP mode, coupled with a short nonpolar core‐shell column in the second dimension, for comprehensive 2D LC separations of phenolic and flavonoid compounds. When the 2D setup with the sulfobetaine–BIGDMA column was used for repeated sample analysis, with alternating gradients of decreasing (hydrophilic‐interaction mode), and increasing (RP mode) concentration of acetonitrile on the sulfobetaine–BIGDMA column in the first dimension, useful complementary information on the sample could be obtained.     

Dicationic imidazolium ionic liquid modified silica as a novel reversed‐phase/anion‐exchange mixed‐mode stationary phase for high‐performance liquid chromatography

A dicationic imidazolium ionic liquid modified silica stationary phase was prepared and evaluated by reversed‐phase/anion‐exchange mixed‐mode chromatography. Model compounds (polycyclic aromatic hydrocarbons and anilines) were separated well on the column by reversed‐phase chromatography; inorganic anions (bromate, bromide, nitrate, iodide, and thiocyanate), and organic anions (p‐aminobenzoic acid, p‐anilinesulfonic acid, sodium benzoate, pathalic acid, and salicylic acid) were also separated individually by anion‐exchange chromatography. Based on the multiple sites of the stationary phase, the column could separate 14 solutes containing the above series of analytes in one run. The dicationic imidazolium ionic liquid modified silica can interact with hydrophobic analytes by the hydrophobic C₆ chain; it can enhance selectivity to aromatic compounds by imidazolium groups; and it also provided anion‐exchange and electrostatic interactions with ionic solutes. Compared with a monocationic ionic liquid functionalized stationary phase, the new stationary phase represented enhanced selectivity owing to more interaction sites.     

Development and application of a new 25,27‐bis(l‐phenylalaninemethylester‐N‐carbonylmethoxy)‐26,28‐dihydroxy‐para‐tert‐butylcalix[4]arene stationary phase

A 25,27‐bis(l ‐phenylalaninemethylester‐N‐carbonylmethoxy)‐26,28‐dihydroxy‐ para‐tert‐butylcalix[4]arene‐bonded silica gel stationary phase was synthesized, structurally characterized and used for LC. Its separation mechanism was studied and compared with octadecyl‐bonded stationary phase, as well as our previously prepared para‐tert‐butylcalix[4]arene‐1,2‐crown‐4 stationary phase. Meanwhile, the chromatographic behaviors were investigated by using polycyclic aromatic hydrocarbons, monosubstituted benzenes, anilines, phenols, Tanaka tests solutes, fluoroquinolones, and flavonoids as probes. Mechanisms involved in the chromatographic separation included hydrophobic, π‐π and π‐electron transfer, hydrogen bonding, and inclusion interactions. Moreover, the column was successfully employed for the analysis of the illegal additive of melamine in milk product.     

Effective on‐line high‐speed shear dispersing emulsifier technique coupled with high‐performance countercurrent chromatography method for simultaneous extraction and isolation of carotenoids from Lycium barbarum L. fruits

An efficient combination strategy based on high‐speed shear dispersing emulsifier technique and high‐performance countercurrent chromatography was developed for on‐line extraction and isolation of carotenoids from the fruits of Lycium barbarum. In this work, the high‐speed shear dispersing emulsifier technique has been employed to extract crude extracts using the upper phase of high‐performance countercurrent chromatography solvent system composed of n‐hexane?dichloromethane?acetonitrile (10:4:6.5, v/v) as the extraction solvent. At the separation stage, the high‐performance counter‐current chromatography process adopts elution–extrusion mode and the upper phase of the solvent system as stationary phase (reverse‐phase mode). As a result, three compounds including zeaxanthin, zeaxanthin monopalmitate, and zeaxanthin dipalmitate with purities of 89, 90, and 93% were successfully obtained in one extraction‐separation operation within 120 min. The targeted compounds were analyzed and identified by high‐performance liquid chromatography, mass spectrometry, and NMR spectroscopy. The results indicated that the present on‐line combination method could serve as a simple, rapid, and effective way to achieve weak polar and unstable compounds from natural products.     

Semi‐preparative high‐speed counter‐current chromatography separation of alkaloids from embryo of the seed of Nelumbo nucifera Gaertn by pH‐gradient elution

A new high‐speed counter‐current chromatography method for semi‐preparative separation and purification of alkaloids from embryo of the seed of Nelumbo nucifera Gaertn was developed by using pH‐gradient elution mode. Diethyl ether was used as the stationary phase of the two‐phase solvent system and Na₂HPO₄/NaH₂PO₄ buffer solution with pH values of 7.5 and 7.2 in gradient mode as the mobile phase. Consequently, 33 mg of liensinine, 42 mg of isoliensinine, and 67 mg of neferine were obtained from 200 mg of crude extracts. The purities of them were all over 98% as determined by HPLC area normalization method, and the structures were identified by ¹H‐NMR and ¹³C‐NMR.     

Comparison of HPLC enantioseparation of substituted binaphthyls on CD‐, polysaccharide‐ and synthetic polymer‐based chiral stationary phases

Retention and enantioseparation behavior of ten 2,2′‐disubstituted or 2,3,2′‐trisubstituted 1,1′‐binaphthyls and 8,3′‐disubstituted 1,2′‐binaphthyls, which are used as catalysts in asymmetric synthesis, was investigated on eight chiral stationary phases (CSPs) based on β‐CD, polysaccharides (tris(3,5‐dimethylphenylcarbamate) cellulose or amylose CSPs) and new synthetic polymers (trans‐1,2‐diamino‐cyclohexane, trans‐1,2‐diphenylethylenediamine and trans‐9,10‐dihydro‐9,10‐ethanoanthracene‐(11S,12S)‐11,12‐dicarboxylic acid CSPs). Normal‐, reversed‐phase and polar‐organic separation modes were employed. The effect of the mobile phase composition was examined. The enantiomeric separation of binaphthyl derivatives, which possess quite similar structures, was possible in different enantioselective environments. The substituents and their positions on the binaphthyl skeleton affect their properties and, as a consequence, the separation system suitable for their enantioseparation. In general, the presence of ionizable groups on the binaphthyl skeleton, substitution with non‐identical groups and a chiral axis in the 1,2′ position had the greatest impact on the enantiomeric discrimination. The 8,3′‐disubstituted 1,2′‐binaphthyl derivatives were the most easily separated compounds in several separation systems. From all the chiral stationary phases tested, cellulose‐based columns were shown to be the most convenient for enantioseparation of the studied analytes. However, the polymeric CSPs with their complementary behavior provided good enantioselective environments for some derivatives that could be hardly separated in any other chromatographic system.     

Optimization of the surface modification process of cross‐linked polythiol‐coated chiral stationary phases synthesized by a two‐step thiol‐ene click reaction

A new platform technology for the preparation of stable chiral stationary phases was successfully optimized. The chiral selector tert‐butylcarbamoylquinine was firstly covalently connected to the polymer poly(3‐mercaptopropyl)methylsiloxane by thiol‐ene click reaction. Secondly, the quinine carbamate functionalized polysiloxane conjugate was coated onto the surface of vinyl modified silica particles and cross‐linked via thiol‐ene click reaction. The amount of polysiloxane, chiral selector, radical initiator, reaction solvent (chloroform and methanol), reaction time, and pore size of the supporting silica particles were varied and systematically optimized in terms of achievable plate numbers while maintaining simultaneously enantioselectivity. The optimization was based on elemental analysis data, chromatographic results, and H/u‐curves (Van Deemter) of the resultant chiral stationary phases. The results suggest that better chromatographic efficiency (higher plate numbers) at equal enantioselectivity can be achieved with methanol (a poor solvent for the polysiloxane that is dispersed rather than dissolved) and a lower film thickness of quinine carbamate functionalized polysiloxane. In this study, chiral stationary phases based on 100 Å silica slightly outperformed 200 Å silica particles (each 5 μm). The optimized two step material exhibited significantly reduced mass transfer resistance compared to the one step material and equal performance as a brush‐type chiral stationary phase.     

Controllable preparation of a hydrophilic/ion‐exchange mixed‐mode stationary phase by surface‐initiated atom transfer radical polymerization using a mixture of two functional monomers

Mixed‐mode chromatographic stationary phases require functionalization with at least two functional groups to yield multiple interactions with analytes. Departing from reported methods, a mixture of two different monomers, glycidyl methacrylate and 2‐dimethylaminoethylmethacrylate, was grafted onto the surface of silica by a one‐step surface‐initiated atom transfer radical polymerization to prepare a novel hydrophilic interaction/anion‐exchange mixed‐mode chromatographic stationary phase. The grafted amounts of functional groups were controlled via varying the ratio of monomers in the polymerization system. The influences of water content, salt concentration and pH in the mobile phase were investigated to illustrate the mixed interaction between the stationary phase and analytes. The retention of various solutes on three columns, especially acidic and basic solutes, showed an obvious dependence on the ratio of the two monomers in the polymerization system. The results indicated that the strategy proposed in this work was beneficial to develop various types of mixed‐mode chromatographic stationary phases with adjustable selectivity to meet the needs of complex samples. Finally, the column was successfully employed in the isolation of melamine in liquid milk.     

Synthesis and chromatographic evaluation of phenyl/tetrazole bonded stationary phase based on thiol‐epoxy ring opening reaction

A silica‐based reversed‐phase stationary phase bonding with phenyl and tetrazole groups was synthesized by thiol‐epoxy ring opening reaction. The bonded groups could not only provide hydrophobic interaction, but also π–π, hydrogen bonding, electrostatic interactions, and so on. The results of characterization with elemental analysis and solid‐state ¹³C cross‐polarization magic‐angle‐spinning NMR spectroscopy indicated the successful preparation of phenyl/tetrazole sulfoether bonded stationary phase. Chromatographic evaluation revealed that phenyl/tetrazole sulfoether bonded stationary phase behaved well under the reversed‐phase mode. The column parameters (H, S*, A, B, and C) showed different selectivity compared with some typical commercial columns, and it was validated by the separation of estrogen, ginsenoside, alkaloid samples. Based on the different selectivity between phenyl/tetrazole sulfoether bonded stationary phase and C18 columns, phenyl/tetrazole sulfoether bonded stationary phase also showed potential to construct a 2D reversed‐phase liquid chromatography system with C18. And it was verified by the separation of corydalis tuber and curcuma zedoary extracts.     

Selective Pre-concentration and Solid Phase Extraction of Mercury（Ⅱ） from Natural Water by Silica Gel-loaded （E）-N-（1-Thien-2＇-ylethylidene）-1,2-phenylenediamine Phase

Silica gel-loaded （E）-N-（1-thien-2＇-ylethylidene）-1,2-phenylenediamine （TEPDA） phase was synthesized based on physical adsorption approaches. The stability of a chemically modified TEPDA especially in concentrated hydrochloric acid that was then used as a recycling and preconcentration reagent allowed the further uses of silica gel-loaded immobilized TEPDA phase. The application of this silica gel-loaded phase to sorption of a series of metal ions was performed by using different controlling factors such as the pH of the metal ion solution and the equilibration shaking time by the static technique. This difference was interpreted on the basis of selectivity incorporated in these sulfur containing silica gel-loaded TEPDA phases. Hg（Ⅱ） was found to exhibit the highest affinity towards extraction by these silica gel-loaded TEPDA phases. The pronounced selectivity was also confirmed by the determined distribution coefficients （Kd） of all the metal ions, showing the highest value reported for mercury（Ⅱ） extraction by the silica gel immobilized TEPDA phase. The potential applications of the silica gel immobilized TEPDA phase to selective extraction of mercury（Ⅱ） from aqueous solution were successfully accomplished and preconcentration of low concentration of Hg（Ⅱ） （30 pg·mL^-1） from natural tap water with a preconcentration factor of 200 for Hg（Ⅱ） off-line analysis was conducted by cold vapor atomic absorption analysis.     

Preparation and evaluation of diblock copolymer‐grafted silica by sequential surface initiated‐atom transfer radical polymerization for reverse‐phase/ion‐exchange mixed‐mode chromatography

A novel approach that involved the grafting of diblock copolymer with two types of monomer onto substrate by sequential surface initiated‐atom transfer radical polymerization was proposed to prepare a mixed‐mode chromatographic stationary phase. The distinguishing feature of this method is that it can be applied in the preparation of various mixed‐mode stationary phases. In this study, a new reverse‐phase/ion‐exchange stationary phase was prepared by grafting hydrophobic styrene and cationic sodium 4‐styrenesulfonate by the proposed approach onto silica surface. The chromatographic properties of the prepared stationary phase were evaluated by the separation of benzene derivatives, anilines, and β‐agonists, and by the effect of pH values and acetonitrile content on the retention. Compared with typical RP columns, the prepared stationary phase achieved the better resolution and higher selectivity at a shorter separation time and lower organic content. Moreover, the application of the prepared column was proved by separating widely distributed polar and charged compounds simultaneously.     

Novel chiral stationary phases based on peptoid combining a quinine/quinidine moiety through a C9‐position carbamate group

By connecting a quinine or quinidine moiety to the peptoid chain through the C9‐position carbamate group, we synthesized two new chiral selectors. After immobilizing them onto 3‐mercaptopropyl‐modified silica gel, two novel chiral stationary phases were prepared. With neutral, acid, and basic chiral compounds as analytes, we evaluated these two stationary phases and compared their chromatographic performance with chiral columns based on quinine tert‐butyl carbamate and the previous peptoid. From the resolution of neutral and basic analytes under normal‐phase mode, it was found that the new stationary phases exhibited much better enantioselectivity than the quinine tert‐butyl carbamate column; the peptoid moiety played an important role in enantiorecognition, which controlled the elution orders of enantiomers; the assisting role of the cinchona alkaloid moieties was observed in some separations. Under acid polar organic phase mode, it was proved that cinchona alkaloid moieties introduced excellent enantiorecognitions for chiral acid compounds; in some separations, the peptoid moiety affected enantioseparations as well. Overall, chiral moieties with specific enantioselectivity were demonstrated to improve the performance of peptoid chiral stationary phase efficiently.     

Simultaneous quantification of N‐butylthiophosphoric triamide and dicyandiamide in urea formulation by liquid chromatography with tandem mass spectrometry

A new liquid chromatography with tandem mass spectrometry method employing a mixed‐mode zwitterionic stationary phase was developed for simultaneous determination of urease inhibitor (N‐butylthiophosphoric triamide) and nitrification inhibitor (dicyandiamide) in urea fertilizer. Molecular modeling based on density functional theory calculations was employed to provide an insight into the interaction mechanism of urea, dicyandiamide, and N‐butylthiophosphoric triamide with zwitterionic stationary phase in chromatographic separation system. The detection of analytes was performed on a triple quadrupole tandem mass spectrometer in multiple reaction monitoring mode using positive electrospray ionization. The ion transitions monitored were m/z 85→68 for dicyandiamide and m/z 168.2→74 for N‐butylthiophosphoric triamide, respectively. The standard calibration curves of dicyandiamide and N‐butylthiophosphoric triamide were linear over the range of 1.0 ? 15 ppm (coefficient of determination = 0.9984), 0.05 ? 1 ppm (coefficient of determination = 0.9995), with limit of detection of 25 and 5 ppb, respectively. The recoveries of low, middle, and high concentrations were from 96.7 to 105.8% for N‐butylthiophosphoric triamide and 94.4 to 105.8% for dicyandiamide with accuracy (relative error %) of ≤5.8% and ≤5.8%, the precision (coefficients of variation) was ≤2.0% and ≤2.9%, respectively. The validated method was successfully applied on real urea samples to determine N‐butylthiophosphoric triamide and dicyandiamide simultaneously.     

Tetra‐proline‐modified calix[4]arene‐bonded silica stationary phase for simultaneous reversed‐phase/hydrophilic interaction mixed‐mode chromatography

A new water‐soluble tetra‐proline‐modified calix[4]arene‐bonded silica stationary phase was prepared straightforwardly by an indirect method and characterized by elemental analysis, energy dispersive Spectrometry, solid‐state ¹³C NMR spectroscopy, Fourier‐transform infrared spectroscopy, and thermogravimetric analysis. Due to the simultaneous introduction of polar tetra‐proline and nonpolar calix[4]arene, the developed column possessing a double retention mode of reverse‐phase liquid chromatography and hydrophilic interaction liquid chromatography. A series of hydrophobic and hydrophilic test samples, including nucleosides and nucleotides, amines, monosubstituted benzenes, chiral compounds, and phenols, were used to evaluate the developed stationary phase. A rapid separation capability, high separation efficiency, and selectivity were achieved based on the multiple interactions between solutes and tetra‐proline‐modified calix[4]arene‐bonded silica stationary phase. Moreover, the developed stationary phase was further used to detect and separate hexamethylenetetramine in rice flour. All the results indicated the potential merits of the developed stationary phase for simultaneous separation of complex hydrophobic and hydrophilic samples with high selectivity.     

Preparation of a monolithic column with a mixed‐mode stationary phase of reversed‐phase/hydrophilic interaction for capillary liquid chromatography

A monolithic capillary column with a mixed‐mode stationary phase of reversed‐phase/hydrophilic interaction chromatography was prepared for capillary liquid chromatography. The monolith was created by an in‐situ copolymerization of a homemade monomer N,N‐dimethyl‐N‐acryloxyundecyl‐N‐(3‐sulfopropyl) ammonium betaine and a crosslinker pentaerythritol triacrylate in a binary porogen agent consisting of methanol and isopropanol. The functional monomer was designed to have a highly polar zwitterionic sulfobetaine terminal group and a hydrophobic long alkyl chain moiety. The composition of the polymerization solution was systematically optimized to permit the best column performance. The columns were evaluated by using acidic, basic, polar neutral analytes, as well as a set of alkylbenzenes and Triton X100. Very good separations were obtained on the column with the mixed‐mode stationary phase. It was demonstrated that the mixed‐mode stationary phase displayed typic dual retention mechanisms of reversed‐phase/hydrophilic interaction liquid chromatography depending on the content of acetonitrile in the mobile phase. The method for column preparation is reproducible.     

Efficient purification of high‐purity compounds from the stem of Lonicera japonica Thunb using two‐dimensional preparative chromatography

Purification of high‐purity compounds from traditional Chinese medicines (TCMs) plays an important role in investigating their bioactivity. Nevertheless, it is often quite difficult to isolate compounds with high purity because of the complexity of TCMs in chemical composition. In this work, a two‐dimensional preparation method was successfully developed for the preparation of high‐purity compounds from the stem of Lonicera japonica Thunb, based on two novel polar copolymerized RP stationary phases, XAqua C3 and XAqua C18. An XAqua C3 prep column was used to separate the sample in the first‐dimensional preparation, and 14 g of sample was fractionated into eight fractions with a recovery of 82%. An XAqua C18 prep column was selected to prepare high‐purity compounds in the second‐dimensional preparation for its good orthogonality with the XAqua C3 stationary phase. As a result, major compounds in the sample were isolated with more than 99% purity. This method is a potent method to realize the efficient purification of compounds with high purity from the stem of L. japonica Thunb and it shows great potential in the separation of high‐purity compounds from complex samples.