一种频域合成房间频率响应的人工混响方法

给出了一种频域合成房间频率响应的方法用于卷积法人工混响,基于频域内房间频率响应的后期部分为高斯随机过程的假设,用自回归滑动平均模型为其自协方差函数和功率谱密度进行参数化描述,在对自回归滑动平均模型中的参数求解后,通过逆滤波得到了房间频率响应后期部分,与房间频率响应前期部分组合后经过傅里叶反变换得到完整的房间脉冲响应。仿真结果表明该方法的混响效果与镜像源法接近,明显优于反馈延迟网络法,但其计算复杂度比镜像源法低,便于实时应用。     

频域合成房间频率响应的人工混响方法

给出了一种频域合成房间频率响应的方法用于卷积法人工混响,基于频域内房间频率响应的后期部分为高斯随机过程的假设,用自回归滑动平均模型为其自协方差函数和功率谱密度进行参数化描述,在对自回归滑动平均模型中的参数求解后,通过逆滤波得到了房间频率响应后期部分,与房间频率响应前期部分组合后经过傅里叶反变换得到完整的房间脉冲响应。仿真结果表明该方法的混响效果与镜像源法接近,明显优于反馈延迟网络法,但其计算复杂度比镜像源法低,便于实时应用。     

基于飞行计划的惯性导航误差模型分析

为了更有效地评估民航飞机惯性导航性能,更好地分析其惯导数据相对于飞行计划的误差。提出一种新方法整体分析惯导误差,将飞行计划航迹离散化计算出误差数据,使用小波多尺度分析方法,经小波变换将误差分为高频与低频两部分,将非平稳的低频部分进行差分处理转化为平稳时间序列,最终建立惯导误差数据的自回归滑动平均（ARMA）模型。通过与实际快速存取记录器（QAR）数据对比验证,此模型能较好地描述惯导误差,较为准确地描述了民航飞机惯性导航误差,为进一步分析其特性及规律奠定了基础。此方法可用于评估民航飞机惯导性能。     

相空间中离散完整系统的Noether对称性和Mei对称性

研究相空间中离散完整系统的Noether对称性、Mei对称性及其导致的守恒量.利用差分离散变分方法,给出相空间中离散完整系统的差分离散变分原理,建立系统的离散正则方程和能量演化方程;给出系统Noether对称性和Mei对称性的判定条件,得到系统离散形式的Noether守恒量和Mei守恒量及其存在的条件.举例说明结果的应用. 关键词： 相空间 离散完整系统 对称性 守恒量     

完整约束力学系统保Lie对称性差分格式

提出一种保完整约束力学系统Lie点对称性的差分格式.其具体做法是:首先求出完整约束力学系统的Lie点对称群,并将其延拓到离散的差分格点上;其次利用其特征方程找出独立的离散不变量;再应用独立的离散不变量来构造不变量的差分格式,且此差分格式在连续极限下应给出原系统的微分方程;最后给出一个例子,作为本文结果的说明.     

离散差分序列变质量Hamilton系统的Lie对称性与Noether守恒量

本文研究离散差分序列变质量Hamilton系统的Lie对称性与Noether守恒量. 构建了离散差分序列变质量Hamilton系统的差分动力学方程, 给出了离散差分序列变质量Hamilton系统差分动力学方程在无限小变 换群下的Lie对称性的确定方程和定义, 得到了离散力学系统Lie对称性导致Noether守恒量的条件及形式, 举例说明结果的应用. 关键词： 离散力学 Hamilton系统 Lie对称性 Noether守恒量     

确定性系统一步超前控制算法的探讨

确定性动态系统可以用多种方式进行描述和建模。本文首先探讨了用一种自回归滑动平均模型来描述确定性系统的方法及意义,并在此模型的基础上,引出了适合此种模型的一种最小预测误差控制算法——一步超前控制。并以典型的伺服系统为例,进行了仿真研究及参数、性能分析。     

基于ARMA模型的受损限幅器模型建立方法

针对限幅器遭受功能或物理损伤而发生的非线性效应, 给出了一种基于信号分析的受损限幅器非线性效应研究新视角, 并从该视角出发, 提出了模型建立方法。该方法首先测得受损限幅器幅频响应序列, 将其转化为零均值实平稳序列; 然后计算该序列的自相关函数和偏相关函数, 估计自回归滑动平均(ARMA)模型的阶数; 最后采用最小二乘法估计出模型的表达式, 并采用最终预测误差(FPE)准则对该表达式进行校验。试验结果和理论分析验证了该方法的良好效果。     

离散差分变分Hamilton系统的Lie对称性与Noether守恒量

研究离散差分Hamilton系统的Lie对称性与Noether守恒量. 根据扩展的时间离散力学变分原理构建Hamilton系统的差分动力学方程.定义离散系统运动差分方程在无限小变换群下的不变性为Lie对称性, 导出由Lie对称性得到系统离散Noether守恒量的判据. 举例说明结果的应用. 关键词： 离散力学 差分Hamilton系统 Lie对称性 Noether守恒量     

基于小波分析的ARIMA与LSSVM组合的高炉煤气预测

高炉煤气发生量的准确预测对钢铁企业能源优化调度具有重要意义。针对钢铁企业中基于机理模型的高炉煤气发生量难以准确预测问题,建立了基于小波分析的最小二乘支持向量机(LSSVM)和自回归差分滑动平均(ARIMA)相结合的高炉煤气预测模型。预测前利用小波去噪对原始数据进行消噪处理,并对处理后的数据进行小波变换得到趋势序列和波动序列,然后对各部分序列分别建模和预测,最后将各部分预测结果叠加;仿真结果表明,组合预测模型减小了预测误差,提高了预测精度。与其他模型相比,组合预测模型更适合高炉煤气预测。     

Low frequency characteristic parameters measurement of vented-box loudspeaker system using total least squares method

I.IntroductiollThecomputeraideddesign(CAD)techniqueisanadvancedmethodforthedesignofvented-boxloudspeakersystemsI1l,whichisbasedontheThiele-Sma.llparametersofloudspeakersIa]andthefowfrequencycharpeteristicparametersofvelltedboxloudspeakersystems.TheThiele-Smallparametersofloudspeakersandsomeofthelowfrequellcycharacteristicparametersofvellted-boxloudspeakersystemshavebeendeterIIilnedbyfrequencyUomainmeth.dI3'4]foralongtime.Themaindisadwtagesofthismethodarecomplicatedandtimeconsuming.TheThi…     

直接辐射式扬声器系统的低频效率计算公式*

效率是扬声器系统的重要性能指标,然而常用的标称效率在低频范围并不适用。本文研究直接辐射式扬声器系统的低频效率,推导了基于TS参数的低频效率计算公式。针对封闭式扬声器系统和倒相式扬声器系统,开展实验验证,结果表明本文提出的计算公式得到的低频效率与实验测量得到的低频效率较为相符。进一步对比分析低频效率和标称效率,结果表明低频效率能够适用于低频,能准确地展示扬声器系统参数对效率的影响。利用本文提出的计算公式,有助于进一步优化提升扬声器系统的低频效率。     

基于Volterra滤波器的参量阵扬声器互调失真补偿研究

针对单边带调制方法预处理的参量阵扬声器系统在复杂信号输入情况下存在明显互调失真的问题,引入Volterra滤波器模型和简化的一维Volterra滤波器模拟了其互调失真。设计了相应的逆滤波器,并对其抑制系统互调失真的性能进行了实验对比。结果表明,所设计的逆滤波器都能有效降低系统的互调失真,而后者具有较低的计算复杂度。     

Identification of a parametric loudspeaker system using an adaptive Volterra filter

Due to the parametric acoustic array effect in air, the input audible signal of a parametric loudspeaker system can be reproduced with high directivity at the target region. However, the reproduced audible signal suffers from harmonic distortion, which is the by-product of nonlinear interaction between the primary waves. In order to investigate this inherent nonlinear phenomenon, a nonlinear system identification model is developed based on an adaptive Volterra filter. Unlike the conventional loudspeaker, the nonlinear characteristic of a parametric loudspeaker system is dependent on several primary parameters in nonlinear acoustics, which include the initial pressure of the primary waves, the observing distance and angle, as well as ambient temperature and relative humidity. By using a truncated Volterra series up to the 2nd-order kernel, numerical simulations are conducted to develop a system model with one group of parameters and examine the quadratic nonlinear intensity for different parameters’ settings. Experimental measurements, which take into account of emitter’s response, are carried out to verify the modeling result and evaluate the model performance. Based on the Volterra system model, the sound pressure level and the harmonic distortion can be accurately predicted.     

Comparison between voltage and current driving methods of a micro-speaker

Since its inception, most audio amplifiers control the loudspeaker in voltage. However previous studies highlighted the importance of the loudspeaker control in current. These studies have been done only with large size loudspeakers (bass or midrange loudspeakers) and this is certainly not transposable for the type of loudspeaker in interest i.e. micro-speaker. First of all, this paper describes a model of loudspeaker (voltage driven and also current driven) represented by a comprehensive set of data based on a minimal number of measurements. Simulation results based on these models are presented using single frequency signals such as multi-frequencies signals to compare the two driven methods. At this level of modelling, simulation results show that, contrary to the woofer applications, current driving of micro-speaker does not affect significantly in terms of harmonic distortions, intermodulation distortions and transient behavior.     

One dimensional study of a module for active/passive control of both absorption and transmission

Hybrid active/passive absorbers have proven to be efficient over a large frequency range. The next step consists in building up a system which can exhibit good absorption and insulation properties. To simulate such hybrid cell, active and passive behaviors of an electroacoustic loudspeaker have been modelized by using a one-dimensional approach. The rear acoustic load at the back of the membrane has been taken into account to obtain a reliable model. The proposed model has been validated with measurements performed in a 7 cm diameter tube. Then, a hybrid cell composed of a porous plate and a small thickness loudspeaker has been designed and numerically tested. It is shown that, when driving the loudspeaker for total absorption, the transmission losses are suppressed at lower frequencies. To overcome this problem, a dual actuator cell is designed to deal with both absorption and transmission. Simulations shows that this solution can lead to good results. It is also shown that interaction of the loudspeakers can be significantly reduced by using directive sources, thus lowering supplying voltages and condition number of the matrix inversion required by the control process.     

平板扬声器用于结构声有源噪声控制实验研究

对NXT技术的分布式平板扬声器和集中参数扬声器的频响和指向性等进行了对比测量，通过对组合平板扬声器的声场研究及有源消声实验，证明了平板扬声器用于有源噪声控制的可行性。综合平板扬声器和集中参数扬声器的物理特点和声场特性，根据基于平面声源有源噪声控制的已有的理论研究结果和本文的实验结果，可以认为，NXT平板扬声器适合作有源噪声控制的次级源，有利于有源噪声控制的工程推广应用。     

Model and estimation method for predicting the sound radiated by a horn loudspeaker - With application to a car horn

This paper deals with a new car horn device made of a sound synthesizer and an electrodynamic horn loudspeaker. It presents an one-dimensional model allowing to predict the loudspeaker efficiency and a specific method to estimate experimentally the model parameters. First, this model aims at reducing the time spent in the design process. Second it aims at correcting the sound emitted by the sound synthesizer in order that the listener hears the sound designed for creating the warning message. The study gives a survey of the vast loudspeaker literature. It is based on the conventional electroacoustic approach used for electrodynamic loudspeakers and on wave propagation models used for characterizing acoustic horns. The estimation of the model parameter values is performed using measurements of the electrical impedance of the loudspeaker and of the acoustic impedance of the horn. The model is assessed by comparing the calculated and measured electrical impedances and horn efficiencies. Results show that the model predicts well the horn efficiency up to 2500 Hz, the limitation being due to the horn radiation impedance modelization.     

A comprehensive discrete-time computer modeling of acoustic Transmission Line loudspeakers

The Transmission Line loudspeaker is an audio loudspeaker enclosure topology devoted to extending the low frequency range near the loudspeaker frequency resonance. A few models based on physical properties of damped pipes have been proposed to characterize the Transmission Line loudspeaker systems. Unfortunately, Thiele/Small parameters, which are usually employed in enclosure designs, are not useful as parameters of design for these loudspeakers. In this paper, a comprehensive numerical formulation of a Transmission Line loudspeaker is presented, which is based in a finite difference approach of the governing equations, including the effects of the absorbing material allocated inside the pipe. The influence of the main empirical parameters is tested on the proposed model, which is also compared to a real prototype for validation purposes.     

扬声器异常音的快速检测方法及其实验研究

提出了一种对扬声器声响应中的低阶次谐波失真与高阶次谐波失真和进行综合分析的方法,以实现对扬声器异常音的快速检测。文章分析了扬声器异常音的时域和频域特征,并对人耳听测异常音的机理进行了讨论。通过对扬声器系统Volterra建模并选择连续对数扫频信号作为激励信号,推导出了该模型在此激励下的响应表达式.该表达式揭示了提取各阶冲激响应的方法,由该表达式给出一种可以快速提取各阶次谐波失真的跟踪滤波器,以实现对扬声器异常音的检测。实验室测试和多次工厂生产线测试初步验证了该方法的准确性、快速性和可行性。