类球状微米金刚石聚晶的场发射

在覆盖金属钛层的陶瓷上,采用微波等离子体化学气相沉积(MPCVD)法制备出类球状微米金刚石聚晶薄膜。利用扫描电子显微镜、拉曼光谱,X射线衍射,分析了薄膜的结构和表面形貌。测试了类球状微米金刚石聚晶膜的场致电子发射特性。开启电场仅为0.55V/μm,在2.18V/μm的电场下,其场发射电流密度高达11mA/cm2。仔细分析了膜的发射过程,发现类球状微米金刚石聚晶的结构对发射有很大影响,并对其发射机理进行了研究。     

氮离子注入对类球状微米金刚石聚晶膜的影响

利用微波等离子体化学气相沉积法,在覆盖金属钛层的陶瓷衬底上制备出类球状微米金刚石聚晶膜,后对膜的表面进行氮离子的注入.通过扫描电子显微镜、拉曼光谱、X射线衍射谱及二级结构场发射测试,对膜进行了注入前后的分析.氮离子注入后场致电子发射的效果变强,这可能是氮离子的注入增加了类球状微米金刚石聚晶膜表面的缺陷度,从而增加了价带和导带间的缺陷能级,使电子更容易跃迁到高能级上,提高了场致电子的发射效果.     

沉积时间对球状微米金刚石聚晶结构的生长及其场发射特性影响

利用微波等离子体化学气相沉积法,在覆盖金属钛层的陶瓷衬底上,通过改变沉积时间制备出不同结构的类球状微米金刚石聚晶碳膜.通过扫描电子显微镜、喇曼光谱、X射线衍射谱对碳膜进行了分析测试,并研究了不同沉积时间下沉积的类球状微米金刚石聚晶薄膜的场致电子发射特性,结果显示:不同的沉积时间所制备的碳膜形貌有很大变化,场致电子发射的...     

沉积时间对球状微米金刚石聚晶结构的生长及其场发射特性影响

利用微波等离子体化学气相沉积法,在覆盖金属钛层的陶瓷衬底上,通过改变沉积时间制备出不同结构的类球状微米金刚石聚晶碳膜.通过扫描电子显微镜、喇曼光谱、X射线衍射谱对碳膜进行了分析测试,并研究了不同沉积时间下沉积的类球状微米金刚石聚晶薄膜的场致电子发射特性.结果显示:不同的沉积时间所制备的碳膜形貌有很大变化,场致电子发射的效果也有很大不同,从而得出了场增强因子的降低和导电通道的增长是场发射效果变差的主要原因.     

类球状微米金刚石聚晶膜场发射的稳定性

在覆盖金属钛层的陶瓷上,利用微波等离子体化学气相沉积(MPCVD)法制备出类球状微米金刚石聚晶膜。通过二极管结构测试了聚晶膜的场致电子发射特性,利用扫描电子显微镜、拉曼光谱、XRD分析了场发射前后薄膜的结构和表面形貌的变化。发现在高场、大电流密度的场发射中,对类球状微米金刚石聚晶薄膜中的金刚石聚晶颗粒影响很小,而对金刚石聚晶颗粒间的非晶碳层影响很大。对类球状微米金刚石聚晶变化机理进行了研究。     

类富勒烯纳米晶CNx薄膜及其场致电子发射特性

利用微波等离子体增强化学气相沉积技术制备出了CNx薄膜,并利用x射线光电子能谱、x射线衍射、扫描电子显微镜和Raman光谱等测试手段对所制备的CNx薄膜的微结构和成分进行了分析.研究了其场致电子发射特性.发现薄膜的结构和场发射特性与反应系中的甲烷、氮气及氢气的流量比有关,当甲烷、氢气及氮气流量比为8/50/50sccm时,制备的薄膜具有弯曲层状的纳米石墨晶体结构(类富勒烯结构)和很好的场发射特性.场发射阈值电场降低至1.1V/μm.当电场为5.9V/μm时,平均电流密度达70μA/cm2,发射点密度大于1×104cm-2.     

类富勒烯纳米晶CNx薄膜及其场致电子发射特性

利用微波等离子体增强化学气相沉积技术制备出了CN_x薄膜,并利用x射线光电子能谱、x射线衍射、扫描电子显微镜和Raman光谱等测试手段对所制备的CN_x薄膜的微结构和成分进行了分析.研究了其场致电子发射特性.发现薄膜的结构和场发射特性与反应系中的甲烷、氮气及氢气的流量比有关,当甲烷、氢气及氮气流量比为8/50/50 sccm时,制备的薄膜具有弯曲层状的纳米石墨晶体结构（类富勒烯结构）和很好的场发射特性.场发射阈值电场降低至1.1V/μm.当电场为5.9V/μm时,平 关键词： 类富勒烯 x薄膜')" href="#">CN_x薄膜 场致电子发射 微波等离子体增强化学气相沉积     

白碳纳米晶薄膜及其场致电子发射特性

利用微波等离子体化学气相沉积方法,以甲烷、氢混合气体为反应气体,具有钛镀层的玻璃作为衬底,制备了具有sp¹杂化结构的白碳纳米晶薄膜。利用X射线衍射、俄歇电子能谱,以及扫描电子显微镜对薄膜结构进行了表征。以白碳纳米晶薄膜为阴极,以镀有ITO透明导电薄膜玻璃为阳极,采用二极管结构,测试了白碳纳米晶薄膜的场致电子发射特性。开启电场为2.5 V/μm,在电场为5 V/μm时的电流密度为200μA/cm²。对白碳纳米晶薄膜生长机理,以及其场致电子发射机制进行了讨论。     

非晶金刚石薄膜的场致电子发射性能研究

利用真空磁过滤弧沉积技术制备出一种高sp³含量的非晶碳膜———非晶金刚石薄膜，并对这种非晶金刚石薄膜的场电子发射特性及其发射机理进行了研究．实验结果表明，在阈值电场低于20V/μm情况下，得到的场发射电流达20—40μA，薄膜的电子发射行为符合Fowler-Nordheim场发射理论．研究表明，这种非晶金刚石薄膜具有负的电子亲合势和较小的有效功函数以及相对较低的禁带宽度 关键词：     

Growth and field emission properties of globe-like diamond microcrystalline-aggregate

The globe-like diamond microcrystalline-aggregates were fabricated by microwave plasma chemical vapor deposition (MPCVD) method. The ceramic with a Ti mental layer was used as substrate. The fabricated diamond was evaluated by Raman scattering spectroscopy, X-ray diffraction spectrum (XRD), and scanning electron microscope (SEM). The field emission properties were tested by using a diode structure in a vacuum. A phosphor-coated indium tin oxide (ITO) anode was used for observing and characterizing the field emission. It was found that the globe-like diamond microcrystalline-aggregates exhibited good electron emission properties. The turn-on field was only 0.55 V/μm, and emission current density as high as 11 mA/cm² was obtained under an applied field of 2.9 V/μm for the first operation. The growth mechanism and field emission properties of the globe-like diamond microcrystalline-aggregates are discussed relating to microstructure and electrical conductivity.     

Electron field emission from boron doped microcrystalline diamond

Field emission properties of hot filament chemical vapor deposited boron doped polycrystalline diamond have been studied. Doping level (N_B) of different samples has been varied by the B/C concentration in the gas feed during the growth process and doping saturation has been observed for high B/C ratios. Threshold field (E_th) for electron emission as function of B/C concentration has been measured, and the influences of grain boundaries, doping level and surface morphology on field emission properties have been investigated. Carrier transport through conductive grains and local emission properties of surface sites have been figured out to be two independent limiting effects in respect of field emission. Emitter current densities of 500 nA cm⁻² were obtained using electric fields less than 8 V/μm.     

单颗粒CVD金刚石的场发射

利用改造的扫描电子显微镜(SEM)设备，在SEM腔体中利用钨(W)探针测试了单颗粒金刚石的I-V与场发射特性，结果表明结晶良好的金刚石的I-V特性服从欧姆定律，而孤立的菜花状金刚石颗粒(cauliflower-like diamond)的I-V特性基本符合Pool-Frenkel输运特性.场发射特性表明，结晶良好的金刚石薄膜基本没有场发射，而孤立的菜花状的金刚石颗粒具有一定的场发射.CVD金刚石的场发射过程中，缺陷对电子的输运起主导作用.     

Field emission properties of nano-structured phosphorus-doped diamond

Nano-structured phosphorus-doped diamonds were fabricated for field emitters and their field emission properties were characterized. Two kinds of nano-structures were prepared; tip array structures and whiskers on tip structures. The tips, which have 100 nm radius and 10 μm height, are used in tip array structures; whiskers have tip radii of 5 nm and height of 500 nm. Following nano-structure formation, a reduction of threshold fields is observed compared to non-patterned flat surfaces. This is ascribed to field concentration at the tips. However, at higher electric fields, a saturation of the emission current is observed due to non-negligible bulk resistances in tips and whiskers.     

氧离子注入微晶金刚石薄膜的微结构与光电性能研究

本文系统研究了氧离子注入剂量和退火温度对含有Si-V发光中 心的微晶金刚石薄膜的微结构和光电性能的影响. 结果表明, 氧离子注入并在较高温度退火有利于提高薄膜中Si-V中心的发光强度. 当氧离子注入剂量从10¹⁴ cm^-2增加到10¹⁵ cm^-2时, 薄膜中Si-V发光强度增强. Hall效应测试结果表明退火后薄膜的面电阻率降低. 不同温度退火时, 氧离子注入薄膜的Si-V发光强度较强时, 薄膜的面电阻率增加, 说明Si-V发光中心不利于提高薄膜的导电性能. Raman光谱测试结果表明, 薄膜中缺陷数量的增多会增强Si-V的发光强度, 而降低薄膜的导电性能. 关键词： 金刚石薄膜 氧离子注入 电学性能 Si-V缺陷     

Field emission from nitrogen-implanted CVD diamond film grown on silicon wafer

Nitrogen was implanted into chemical vapor deposition (CVD) diamond films and the electron field emission properties of the nitrogenated diamond films were investigated. Nitrogen implantation was carried out using 10 keV in the dose range from 1×10¹⁶ to 5×10¹⁷ cm^-2 at room temperature. Raman and X-ray photoelectron spectroscopy measurements revealed that nitrogen implantation damaged the structure of the diamond film and promoted the formation of sp² C–C and sp² C–N bondings. Increasing the implantation dose could lower the threshold field of the emission of the diamond film from 18 V/m to 4 V/m. The effective work function of the nitrogen-implanted CVD diamond films was estimated to be in the range of 0.01–0.1 eV. The enhancement of field emission for nitrogen-implanted CVD diamond films was attributed to the increase of the sp² C bonds fraction and the formation of defect bands within the bulk diamond band gap induced by nitrogen implantation, which could alter the work function and elevate the Fermi level. Consequently, the energy barrier for electron tunneling was reduced.     

Size effect in optical spectra of microcrystalline diamond powders and CVD films

Received: 24 March 1997/Accepted: 27 May 1997     

Optical emission spectroscopy study on depositionprocess of microcrystalline silicon

This paper reports that the optical emission spectroscopy (OES) is used to monitor the plasma during the deposition process of hydrogenated microcrystalline silicon films in a very high frequency plasma enhanced chemical vapour deposition system. The OES intensities (SiH\sj{*}, H微晶硅 VHF-PECVD 发射光谱学 薄膜物理学microcrystalline silicon, VHF-PECVD, optical emission spectroscopy2005-11-092005-11-092005-12-12This paper reports that the optical emission spectroscopy （OES） is used to monitor the plasma during the deposition process of hydrogenated microcrystalline silicon films in a very high frequency plasma enhanced chemical vapour deposition system. The OES intensities （Sill^＊, H^＊ and H^＊β） are investigated by varying the deposition parameters. The result shows that the discharge power, silane concentrations and substrate temperature affect the OES intensities. When the discharge power at silane concentration of 4% increases, the OES intensities increase first and then are constant, the intensities increase with the discharge power monotonously at silane concentration of 6%. The SiH^＊ intensity increases with silane concentration, while the intensities of H^＊α and H^＊β increase first and then decrease. When the substrate temperature increases, the SiH^＊ intensity decreases and the intensities of H^＊α and H^＊β are constant. The correlation between the intensity ratio of IH^＊α/ISiH^＊ and the crystalline volume fraction （Xc） of films is confirmed.     

Influences of grain size and microstructure on optical properties of microcrystalline diamond films

Microcrystalline diamond(MCD) films with different grain sizes ranging from 160 nm to 2200 nm are prepared by using a hot filament chemical vapor deposition(HFCVD) system, and the influences of grain size and structural features on optical properties are investigated. The results show that the film with grain size in a range of 160 nm–310 nm exhibits a higher refractive index in a range of(2.77–2.92). With grain size increasing to 620±300 nm, the refractive index shows a value between 2.39 and 2.47, approaching to that of natural diamond(2.37–2.55), and a lower extinction coefficient value between 0.08 and 0.77. When the grain size increases to 2200 nm, the value of refractive index increases to a value between 2.66 and 2.81, and the extinction coefficient increases to a value in a range of 0.22–1.28. Visible Raman spectroscopy measurements show that all samples have distinct diamond peaks located in a range of 1331 cm~(-1)–1333 cm~(-1),the content of diamond phase increases gradually as grain size increases, and the amount of trans-polyacetylene(TPA)content decreases. Meanwhile, the sp~2 carbon clusters content and its full-width-at-half-maximum(FWHM) value are significantly reduced in MCD film with a grain size of 620 nm, which is beneficial to the improvement of the optical properties of the films.