催化剂量甘油对THF-FER沸石结晶过程的加速作用

The hydrothermal crystallization of THF-FER zeolite was investigated in the reactant system of Na2O-SiO2-Al2O3-H2O with tetrahydrofuran （THF） as the template in the presence of various catalytic amount of glycerol [CH2（OH）CH（OH）CH2（OH）, Glyc] in the temperature range of 413--473 K. Powder X-ray diffraction （XRD） was used to observe the crystallization process, and scanning electron microscope （SEM）, ^13C cross polarization （CP） and ^27Al magic angle spinning nuclear magnetic resonance （MAS NMR）, X-ray fluorescence scattering spectroscopy （XRF）, thermal analysis and nitrogen sorption were used to characterize the zeolite synthesized in the reactant system with Glyc. The catalytic amount of Glyc could promote the crystallization of FER zeolite, to result in lowering the reaction temperature, shortening the period of the zeolite crystallization and effectively restraining cocrystallization of MOR zeolite as an impure phase especially at low reaction temperature, and possess a significant effect on the morphology and the crystal size of TI-IF-FER zeolite.     

Investigation of the Mechanism of Colloidal Silicalite‐1 Crystallization by Using DLS,SAXS, and 29Si NMR Spectroscopy

Colloidal silicalite‐1 zeolite was crystallized from a concentrated clear sol prepared from tetraethylorthosilicate (TEOS) and aqueous tetrapropylammonium hydroxide (TPAOH) solution at 95 °C. The silicate speciation was monitored by using dynamic light scattering (DLS), synchrotron small‐angle X‐ray scattering (SAXS), and quantitative liquid‐state ²⁹Si NMR spectroscopy. The silicon atoms were present in dissolved oligomers, two discrete nanoparticle populations approximately 2 and 6 nm in size, and crystals. On the basis of new insight into the evolution of the different nanoparticle populations and of the silicate connectivity in the nanoparticles, a refined crystallization mechanism was derived. Upon combining the reagents, different types of nanoparticles (ca. 2 nm) are formed. A fraction of these nanoparticles with the least condensed silicate structure does not participate in the crystallization process. After completion of the crystallization, they represent the residual silicon atoms. Nanoparticles with a more condensed silicate network grow until approximately 6 nm and evolve into building blocks for nucleation and growth of the silicalite‐1 crystals. The silicate network connectivity of nanoparticles suitable for nucleation and growth increasingly resembles that of the final zeolite. This new insight into the two classes of nanoparticles will be useful to tune the syntheses of silicalite‐1 for maximum yield.     

Tailoring Zeolite ZSM‐5 Crystal Morphology/Porosity through Flexible Utilization of Silicalite‐1 Seeds as Templates: Unusual Crystallization Pathways in a Heterogeneous System

Diffusion limitation in micropores of zeolites leads to a demand for optimization of zeolite morphology and/or porosity. However, tailoring crystallization processes to realize targeted morphology/porosity is a major challenge in zeolite synthesis. On the basis of previous work on the salt‐aided, seed‐induced route, the template effect of seeds on the formation of micropores, mesopores and even macropores was further explored to selectively achieve desired hierarchical architectures. By carefully investigating the crystallization processes of two typical samples with distinct crystal morphologies, namely, 1) nanocrystallite‐oriented self‐assembled ZSM‐5 zeolite and 2) enriched intracrystal mesoporous ZSM‐5 zeolite, a detailed mechanism is proposed to clarify the role of silicalite‐1 seeds in the formation of diverse morphologies in a salt‐rich heterogeneous system, combined with the transformation of seed‐embedded aluminosilicate gel. On the basis of these conclusions, the morphologies/porosities of products were precisely tailored by deliberately adjusting the synthesis parameters (KF/Si, tetrapropylammonium bromide/Si and H₂O/Si ratios and type of organic template) to regulate the kinetics of seed dissolution and seed‐induced recrystallization. This work may not only provide a practical route to control zeolite crystallization for tailoring crystal morphology, but also expands the knowledge of crystal growth mechanisms in a heterogeneous system.     

Gamma‐Ray Irradiation to Accelerate Crystallization of Mesoporous Zeolites

Gamma‐ray (γ‐ray) irradiation was introduced into zeolite synthesis. The crystallization process of zeolite NaA, NaY, Silicalite‐1, and ZSM‐5 were greatly accelerated. The crystallization time of NaA zeolite was significantly decreased to 18 h under γ‐ray irradiation at 20 °C, while more than 102 h was needed for the conventional process. Unexpectedly, more mesopores were created during this process, and thus the adsorption capacity of CO₂ increased by 6‐fold compared to the NaA prepared without γ‐ray irradiation. Solid experimental evidence and density function theory (DFT) calculations demonstrated that hydroxyl free radicals (OH*) generated by γ‐rays accelerated the crystallization of zeolite NaA. Besides NaA, mesoporous ZSM‐5 with MFI topology was also successfully synthesized under γ‐ray irradiation, which possessed excellent catalytic performance for methanol conversion, suggesting the universality of this new synthetic strategy for various zeolites.     

Development of two new approaches for preparation of zirconium silicate systems at low temperature

Homogeneous and stable zirconium silicate sols and gels were prepared via the sol-gel process. Two synthesis procedures were explored based on using acetylacetone (acac) and acetic acid (HOAc) as modifying agents. The homogeneous sols were characterized by small angle x-ray scattering (SAXS) and ²⁹Si NMR in the early stages of polymerization. Zr addition to the Si sols caused significant modification of the extent of condensation of the Si species as determined by ²⁹Si NMR. TGA and DTA of the two types of xerogels revealed differences attributed to the modifying agents. Fourier Transform Infrared (FTIR) spectroscopy of acac xerogels showed a band at 1600 cm^–1, assigned to acac bonded to Zr. FTIR spectra of the HOAc xerogels were consistent with OAc bidentate ligands bonded to Zr. UV-Vis spectroscopy results of the HOAc2.3 thin film presented a band assigned to OAc singly coordinated to Zr.     

AgCu NP Formation by the Ag NP Catalysis of Cu Ions at Room Temperature and Their Antibacterial Efficacy: A Kinetic Study

Although a facile route to prepare AgCu nanoalloys (NAs) with enhanced antibacterial efficacy using Ag NP catalysis of Cu ions at elevated temperatures was previously developed, its detailed reaction process is still unclear due to the fast reaction process at higher temperatures. This work found that AgCu NAs can also be synthesized by the same process but at room temperature. AgCu NAs formation kinetics have been studied using UV–Visible spectra and Transmission Electron Microscopy (TEM), where formation includes Cu²⁺ deposition onto the Ag NP surface and Ag⁺ release, reduction, and agglomeration to form new Ag NPs; this is followed by a redistribution of the NA components and coalescence to form larger AgCu NPs. It is found that SPR absorption is linear with time early in the reaction, as expected for both pseudo-first-order (PFO) and pseudo-second-order (PSO) kinetics; neither model is followed subsequently due to contributions from newly formed Ag NPs and AgCu NAs. The antibacterial efficacy of the AgCu NAs thus formed was estimated, with a continuous increase over the whole alloying process, demonstrating the correlation of antibacterial efficacy with the extent of AgCu NA formation and Ag⁺ release.     

羟基自由基在沸石分子筛合成中的作用

沸石分子筛由于具有独特的形选催化作用及可调的酸性, 已成为化学工业中最重要的固体催化材料. 沸石分子筛的合成主要基于碱性条件下的水热晶化, OH^?被认为起到催化硅铝物种的解聚及聚合作用. 近年来, 研究者发现了羟基自由基加速分子筛的水热晶化机制. 通过利用紫外光照射或芬顿反应等物理或化学方法向分子筛合成体系引入羟基自由基, 可以实现沸石分子筛的加速晶化及高硅沸石分子筛的合成. 理论计算结果表明, 羟基自由基可以促进Si—O—Si 键的断裂和重新生成, 从而显著加快分子筛成核并促进硅原子进入骨架. 本综述介绍了羟基自由基在沸石分子筛晶化方面的最新研究进展, 探讨了羟基自由基的主要作用和优势, 并对沸石分子筛合成的羟基自由基路线发展前景进行了展望.     

The interaction of dibutyltin dilaureate with tetraethyl orthosilicate in sol-gel systems

Sols composed of dibutyltin dilaureate (DTL) and tetraethyl orthosilicate (TEOS) were prepared using a mixture of methyl ethyl ketone (MEK) and acetone as the solvent in order to study the interaction between the oligomeric Sn and Si species. The hydrolysis molar ratio r (r=nH₂O/nM (M: Si, Sn or Si+Sn) was 2. The use of an acid or basic catalyst was avoided, as the sols are intended to be used in the formulation of potential stone consolidants. The sols were studied by several spectroscopic techniques including Small Angle X-ray Scattering (SAXS), ²⁹Si and ¹¹⁹Sn NMR, Fourier Transform Infrared (FTIR) spectroscopy and X-ray diffraction (XRD). According to the spectroscopic results the lauric acid produced by the hydrolysis of DTL modifies the condensation path of the Si species, leading to the formation of two types of oligomeric chains: linear swollen and multiparticle diffusion-limited aggregates, depending on the molar ratio Sn/Si. The ²⁹Si NMR results indicated that the hydrolysis of DTL catalizes the condensation of the Si species, giving as a result higher condensation extents of the Si species in the Sn-Si sols compared to a pure Si sol. Based on the Radial Distribution functions (RDF) and the FTIR results, heterocondensation occurred.     

TS-1分子筛骨架钛原子引入过程的研究

采用廉价的四丙基溴化铵（ＴＰＡＢｒ）为模板剂合成了ＴＳ１分子筛．在晶化过程中,运用ＸＲＤ,ＩＣＰ,ＩＲ,２９ＳｉＭＡＳＮＭＲ和ＵＶＶｉｓ光谱等表征手段,系统地研究了钛原子引入分子筛骨架的机制,观察到钛原子随分子筛的形成同步进入骨架的规律．另外,尽管在晶化初期固相中没有ＴｉＯ２结晶出现,但存在分散态的ＴｉＯｘ物种．随晶化时间的延长,液相中钛物种之间聚合的几率增加,使固相中ＴｉＯ２晶体不断形成．     

A New Family of Two‐Dimensional Zeolites Prepared from the Intermediate Layered Precursor IPC‐3P Obtained during the Synthesis of TUN Zeolite

The crystallization of zeolite TUN with 1,4‐bis(N‐methylpyrrolidinium)butane as template proceeds through an intermediate, designated IPC‐3P, following the Ostwald rule of successive transformations. This apparently layered transient product has been thoroughly investigated and found to consist of MWW monolayers stacked without alignment in register, that is, disordered compared with MCM‐22P. The structure was confirmed based on X‐ray diffraction and high‐resolution (HR)TEM analysis. The layered zeolite precursor IPC‐3P can be swollen and pillared affording a combined micro‐ and mesoporous material with enhanced Brunauer–Emmett–Teller (BET) surface area (685 m²g^?1) and greater accessibility of Brønsted acid sites for bulky molecules. This mesoporous material was probed with 2,6‐di‐tert‐butylpyridine (DTBP). IPC‐3P and its modification create a new layered zeolite sub‐family belonging to the MWW family. FTIR data indicate that (Al)MWW materials MCM‐22 and IPC‐3 with Si/Al ratios greater than 20 exhibit a lower relative ratio of Brønsted to Lewis acid sites than MCM‐22 (with Si/Al ratios of around 13), that is, less than 2 versus more than 3, respectively. This is maintained even upon pillaring and warrants further exploration of materials like IPC‐3P with a higher Al content. The unique XRD features of IPC‐3P indicating misaligned stacking of layers and distinct from MCM‐22P, are also seen in other MWW materials such as EMM‐10P, hexamethonium‐templated (HM)‐MCM‐22, ITQ‐30, and UZM‐8 suggesting the need for more detailed study of their identity and properties.     

Structure-property relationships in thin films and membranes

The molecular-scale species distributions and intermediate-scale structure of silicate sols influence the microstructures of the corresponding thin films prepared by dip-coating. Using multi-step hydrolysis procedures, we find that, depending on the sequence and timing of the successive steps, the species distributions (determined by ²⁹Si NMR) and intermediate scale structure (determined by SAXS) can change remarkably for sols prepared with the same nominal composition. During film formation, these kinetic effects cause differences in the efficiency of packing of the silicate species, leading to thin film structures with different porosities.     

Recrystallization of Zeolite Y to Analcime and Zeolite P with <SC>d</SC>‐Methionine as Structure‐Directing Agent (SDA)

In this study, the synthesis of template free zeolite Y and its recrystallization to two types of pure zeolite P and analcime in the presence of the amino acid d‐methionine as structure‐directing agent were investigated. The recrystallization occurred solely when specific heating cycles were applyed. A completely crystallized phase of zeolite Y for the mixture of zeolite P and analcime was observed in the presence of d‐methionine at a concentration of 0.015 <SC>m</SC>. The effect of different Si/Al ratios (2.3–9.3), crystallization temperatures (40–160 °C), and crystallization times (28–96 hours) on the achievement of two different zeolite types were studied as well. Pure zeolite P was obtained during conventional heating to 100 °C for 42 hours, whereas pure analcime zeolite was achieved by heating the mixture to 160 °C for 96 hours. The products were characterized by X‐ray diffraction, scanning electron microscopy, and IR spectroscopy.     

Synthesis of NaX and NaY Zeolites from Tunisian Kaolinite as Base Catalysts: An Investigation of Knoevenagel Condensation

The synthesis of Faujasite‐type zeolites with high purity has been successfully performed from Tunisian kaolinite and the effects of different crystallization parameters on the final products were widely investigated. The alkaline fusion of kaolinite followed by hydrothermal treatment lead to zeolite NaX synthesis whereas the classic hydrothermal transformation of metakaolinite produces NaY zeolite. The results show that an increase in the synthesis temperature and time has improved the crystallization process of the zeolite NaX whereas the SiO₂/Al₂O₃ and the Na₂O/SiO₂ molar ratios were the key parameters to obtain a pure zeolite NaY. The highest specific surface areas obtained with the optimal crystallization conditions were 554 m2 g^?1 and 592 m2 g^?1 for respectively NaX and NaY zeolites. The basic properties of NaX and NaY zeolites were explored in the Knoevenagel condensation of benzaldehyde with ethyl cyanoacetate at 140 °C as a test reaction in the absence of solvent. The influence of ion exchange with cesium cation on the catalytic activity of prepared catalysts was also investigated. It was found that the NaX provided higher activity than that of NaY catalyst due to its lower Si/Al ratio whereas a cesium exchange conferred higher basicity to the prepared Na‐faujasite.     

Preparation and characterization of novel polyimide‐silica hybrids

Polyimide‐silica (PI‐SiO₂) hybrids were prepared from a novel polyimide (PI), derived from pyromellitic dianhydride (PMDA), 1,6‐bis(4‐aminophenoxy)hexane (synthesized) and 4,4′‐oxydianiline. SiO₂ networks (5–30 wt%) were generated through sol–gel process using either tetraethylorthosilicate (TEOS) or a mixture of 3‐aminopropyltriethoxysilane‐PMDA‐based coupling oligomers (APA) and TEOS. Thin, free standing hybrid films were obtained from the respective mixtures by casting and curing processes. The hybrid films were characterized using Fourier transform infrared, ²⁹Si nuclear magnetic resonance (NMR), field emission scanning electron microscopy (FE‐SEM), energy dispersive X‐ray spectrometry and atomic force microscopy (AFM) techniques. ²⁹Si NMR results provide information about formation of organically modified silicate structures that were further substantiated by FE‐SEM and AFM micrographs. Contact angle measurements and thermogravimetric thermograms reveal that the addition of APA profoundly influences surface energy, interfacial tension, thermal stability and the residual char yield of modified hybrids in comparison to those obtained by mixing only TEOS. It was found that reduced particle size, efficient dispersion and improved interphase interactions were responsible for the eventual property enhancement. Copyright © 2012 John Wiley & Sons, Ltd.     

Characterization of the electronic structure and thermal stability of HfO2/SiO2/Si gate dielectric stack

X‐ray photoelectron spectroscopy was used to investigate thermal stability of HfO₂ on SiO₂/Si substrate prepared by atomic layer deposition, followed by annealing at different temperature. Hf silicate and Hf silicide are formed at the interface of HfO₂ and SiO₂ during deposition. The Hf silicide disappears, while the amount of the Hf silicate is intensified after post‐deposition annealing treatment at 400 °C. Phase separation of the Hf silicate layer occurs when the annealing temperature is over 400 °C, resulting in the Hf silicate decomposition into Si and Hf oxides. Moreover, crystallization at high temperature leads to grain boundaries formation, which deteriorates the gate leakage current, as observed by the electrical measurements. The similar annealing temperature dependence of both internal electric field and the amount of Hf silicate implies that the Hf silicate plays a key role in building up the internal electric field, which is attributed to generation of oxygen vacancies (V_o) in the Hf silicate layer. Copyright © 2017 John Wiley & Sons, Ltd.     

A facile preparation method for synthesis of silica sulfuric acid/poly(o‐methoxyaniline) core–shell nanocomposite

A new nanocomposite of poly(o‐methoxyaniline) (POMA) is introduced by overlayer formation of POMA on silica. The key appealing feature of the synthesis is the role of silica sulfuric acid (SSA) both as solid acid dopant and template in overlayer self‐assembly of POMA on silica surface. Hereon siloxide group (Si―O^?) of silica surface is replaced with dopant anion of SSA (≡Si―O―SO₃^?), which leads to formation of a overlayer of POMA on the silica surface. The composite particles are spherical in the nanoscale range of 50 nm without application of any external template (no‐template synthesis). Nanocomposite was fully characterized by various instrumentation methods: Fourier transform infrared (FT‐IR), ultraviolet–visible (UV–vis), thermogravimetric analysis (TGA), diffrential thermal analysis (DTA), elemental analysis (CHNS), energy dispersive X‐ray (EDX), X‐ray photoelectron spectroscopy (XPS) and X‐ray difraction (XRD). Based on XPS and CHNS results, it is demonstrated that the doping level of POMA is as high as 50% and for the first time the ratio of 4:2:2 is obtained for ―NH― (amine): ―HN^.+― (polarons): ?HN⁺― (bipolarons), respectively. In fact, bipolarons may also coexist with polarons with a 1:1 ratio of them. Moreover, the synthesis benefits from the perspective of green chemistry which is preparation under solid‐state (solvent‐free) condition. Copyright © 2015 John Wiley & Sons, Ltd.     

Organic‐Free Synthesis of a Highly Siliceous Faujasite Zeolite with Spatially Biased Q4(nAl) Si Speciation

We report the most siliceous FAU‐type zeolite, HOU‐3, prepared via a one‐step organic‐free synthesis route. Computational studies indicate that it is thermodynamically feasible to synthesize FAU with SAR=2–7, though kinetic factors seemingly impose a more restricted upper limit for HOU‐3 (SAR≈3). Our findings suggest that a slow rate of crystallization and/or low concentration of Na⁺ ions in HOU‐3 growth mixtures facilitate Si incorporation into the framework. Interestingly, Q⁴(nAl) Si speciation measured by solid‐state NMR can only be modeled with a few combinations of Al positioning at tetrahedral sites in the crystal unit cell, indicating the distribution of Si(‐O‐Si)_4−n(‐O‐Al)_n species is spatially biased as opposed to being random. Achieving higher SAR is desirable for improved zeolite (hydro)thermal stability and enhanced catalytic performance, which we demonstrate in benchmark tests that show HOU‐3 is superior to commercial zeolite Y.     

Phosphatation of Zeolite H‐ZSM‐5: A Combined Microscopy and Spectroscopy Study

A variety of phosphated zeolite H‐ZSM‐5 samples are investigated by using a combination of Fourier transfer infrared (FTIR) spectroscopy, single pulse ²⁷Al, ²⁹Si, ³¹P, ¹H‐³¹P cross polarization (CP), ²⁷Al‐³¹P CP, and ²⁷Al 3Q magic angle spinning nuclear magnetic resonance (MAS NMR) spectroscopy, scanning transmission X‐ray microscopy (STXM) and N₂ physisorption. This approach leads to insights into the physicochemical processes that take place during phosphatation. Direct phosphatation of H‐ZSM‐5 promotes zeolite aggregation, as phosphorus does not penetrate deep into the zeolite material and is mostly found on and close to the outer surface of the zeolite, acting as a glue. Phosphatation of pre‐steamed H‐ZSM‐5 gives rise to the formation of a crystalline tridymite AlPO₄ phase, which is found in the mesopores of dealuminated H‐ZSM‐5. Framework aluminum species interacting with phosphorus are not affected by hydrothermal treatment. Dealuminated H‐ZSM‐5, containing AlPO₄, retains relatively more framework Al atoms and acid sites during hydrothermal treatment than directly phosphated H‐ZSM‐5.     

The New λ6Si‐Silicate Dianion [Si(NCO)6]2−: Synthesis and Structural Characterization of [K(18‐crown‐6)]2[Si(NCO)6]

The λ⁶Si‐silicate [K(18‐crown‐6)]₂[Si(NCO)₆] ( 10 ) was synthesized by treatment of Si(NCO)₄ with KNCO in the presence of 18‐crown‐6. Compound 10 (SiN₆ skeleton) is the first example of a hexa(cyanato‐N)silicate. It was characterized by solid‐state and solution NMR spectroscopy, and the acetonitrile solvate 10· 2CH₃CN was studied by single‐crystal X‐ray diffraction. To differentiate between the two isomeric [Si(NCO)₆]^2? and [Si(OCN)₆]^2? dianions, computational studies were performed.     

Reactivity of Extra‐framework Species of USY Zeolites in Alkaline Medium

Zeolites of type USY (ultra‐stable Y) were obtained by steaming of NH₄NaY modification. Samples were modified by subsequent alkaline treatment in KOH solution. USY and USY‐KOH were characterised by chemical element analysis, XRD, IR, ²⁹Al and ²⁹Si MAS NMR spectroscopic measurements. Correct silicon to aluminium ratios (Si/Al) were determined by XRD and IR (double ring vibration w_DR) data whereas values calculated according to data of ²⁹Si MAS NMR and IR spectroscopy (asymmetrical TOT valence vibration w_TOT) appeared to be too high., In the latter case, the signals of the zeolite framework were strongly superimposed by that of extra‐framework silica gel (EFSi) formed during steaming. It was found that alkaline leaching induces desilication of silicon‐rich area of the zeolite framework and partial dissolution of EFSi. Silicate ions of both react with likewise dissolved extra‐framework aluminium (EFAl) to form X‐ray amorphous aluminosilicate. Consequently, the superposition of the ²⁹Si MAS NMR signals of the zeolite framework by silica gel was reduced for Q⁴(0Al) but increased for Q⁴ (2Al) and Q⁴(3Al) structure units. A reinsertion of EFAl into the zeolite framework has not been observed.