气相色谱-质谱法测定汽车材料中7种苯系物

采用气相色谱-质谱法测定汽车材料中7种苯系物的含量。在气相色谱分离中用HP-5MS色谱柱为固定相,在质谱分析中采用全扫描和选择离子监测模式。以氘代苯-D6为内标物。7种苯系物的线性范围均为1 0~1 000ng,检出限(3s)在9~18ng之间。苯系物测定结果的相对标准偏差(n=6)在0.81%~2.4%之间,加标回收率在99.0%~102%之间。     

高效液相色谱法测定建筑用胶中苯系物和邻苯二甲酸酯类增塑剂

采用高效液相色谱法同时测定建筑用胶中苯系物和邻苯二甲酸酯类增塑剂。样品以乙酸乙酯为萃取剂超声提取,采用C18柱为固定相,乙腈、水为流动相进行梯度洗脱,采用二极管阵列检测器,在254 nm处测定。5种苯系物和5种邻苯二甲酸酯类增塑剂的峰面积与其质量浓度呈线性关系,线性范围在1~3个数量级之间,对苯系物的检出限(3S/N)在0.003~0.006 g.L-1之间,对邻苯二甲酸酯类增塑剂的检出限(3S/N)在0.003 g.L-1之内。对水基型和溶剂型建筑用胶中各物质的回收率在98.1%~101.9%之间。5个实验室间对相同建筑用胶样品中不同目标物测定的相对标准偏差(n=6)在0.8%~4.2%之间。     

催化发光法同时测定空气中的甲醛、苯和二氧化硫

基于甲醛、苯和二氧化硫在纳米Ti3CeY2O11上的催化发光有交叉敏感现象,在3个波长处分别确定甲醛、苯和二氧化硫浓度与催化发光信号强度的响应关系,再依据发光信号强度的叠加性特征即可获取甲醛、苯和二氧化硫的准确浓度,据此建立了同时测定空气中甲醛、苯和二氧化硫的新方法.3个分析波长分别为420、535和680 nm,敏感材料表面温度为280℃,载气流速为130 mL/min.本方法对甲醛、苯和二氧化硫的检出限(3σ)分别为0.04、0.05和0.10 mg/m3,线性范围分别为0.08~75.60 mg/m3、0.10~101.40 mg/m3和0.30~115.00 mg/m3, 回收率分别为96.4%~103.7%、97.8%~102.5%和97.2%~103.3%.常见共存物,如乙醛、甲苯、硫化氢、氨、甲醇、乙醇和二氧化碳等不干扰测定.连续200 h通浓度均为50 mg/m3的甲醛、苯和二氧化硫混合气体,发光强度的相对偏差≤2%,表明此纳米级复合氧化物对甲醛、苯和二氧化硫的敏感性的寿命长.本方法充分利用了交叉敏感现象,可以实现空气中甲醛、苯和二氧化硫的在线分析.     

高效液相色谱法测定生物体液中γ-氨基丁酸

研究了邻苯二甲醛柱前衍生反相高效液相色谱法测定血浆和脑脊液中γ-氨基丁酸的含量。色谱条件:色谱柱为Nova-pak C18柱,流动相为50 mmol.L-1的乙酸钠(pH 6.8)、甲醇和四氢呋喃(A:82∶17∶1;B:22∶77∶1,V/V),梯度洗脱。方法的线性范围为0.5~100μmol.L-1,检出限为0.04μmol.L-1。日间和日内测定的精密度分别为1.9%~6.8%和1.6%~5.7%;标准加入回收率在92.7%与96.8%之间。采用上述方法测定正常人和癫痫病患者血浆和脑脊液中γ-氨基丁酸含量,结果令人满意。     

纳米CeO_2催化鲁米诺化学发光法检测羟苯磺酸钙的研究

在碱性条件下,CeO_2纳米粒子对鲁米诺-H_2O_2化学发光体系有很强的催化增敏作用,而羟苯磺酸钙的加入可线性抑制这一体系化学发光信号。基于此,在最佳实验条件下,结合流动注射技术,建立了测定羟苯磺酸钙的新方法,并对其可能的发光机理进行了探讨。测定羟苯磺酸钙的线性范围为1.0×10~(-7) mol·L~(-1)~5.0×10~(-4) mol·L~(-1),相关系数R~2为0.9954,检出限(3σ)为3.0×10~(-8) mol·L-1,相对标准偏差(RSD)为0.46%(1.0×10~(-6) mol·L~(-1)羟苯磺酸钙溶液,n=11)。该方法用于尿液中羟苯磺酸钙的含量测定,回收率为96.7%~98.0%,结果令人满意。     

顶空-气相色谱-质谱法测定地表水和废水中55种挥发性有机物含量

采用顶空-气相色谱-质谱法测定地表水和废水中55种挥发性有机物的含量。选择顶空平衡温度和时间分别为65℃和50min。在气相色谱分离中用DB-624色谱柱为固定相,在质谱分析中采用全扫描和选择离子监测模式。以氟苯和1,2-二氯苯-D4为内标物。55种挥发性有机物的线性范围均为10.0~400μg·L-1。全扫描模式下,检出限在0.8~6.8μg·L-1之间,加标回收率在81.3%~116%之间,测定值的相对标准偏差(n=6)在0.40%~15%之间。在选择离子监测模式下,检出限在0.2~1.1μg·L-1之间,加标回收率在81.0%~117%之间,测定值的相对标准偏差(n=6)在0.40%~6.5%之间。     

液相色谱串联质谱法同时测定饲料中8种苯并咪唑类药物

建立了同时测定饲料中8种苯并咪唑类药物(噻苯咪唑、丙硫咪唑、硫苯咪唑、苯硫氧咪唑、氟苯咪唑、甲苯咪唑、丙氧苯唑和三氯苯唑)的液相色谱串联质谱分析方法。饲料样品用酸化乙腈直接提取,提取液用甲酸溶液稀释后进行分析。分析时用XBridgeTMC18色谱柱,以甲酸溶液-乙腈体系进行梯度洗脱,MRM方式测定,基质外标法定量。8种苯并咪唑类药物均在0.02~10.0 mg.L-1范围内呈良好的线性关系,相关系数(r2)均不低于0.990,在饲料样品中的检出限为2.1~63.0μg.kg-1。饲料中苯并咪唑类药物在0.50、30、200 mg.kg-13种加标水平下的回收率为84%~104%,相对标准偏差均小于10.0%。方法分析单个样品约需30 min,该方法适合饲料中8种苯并咪唑类药物的同时分析。     

GC–MS法同时测定聚氨酯塑胶跑道中16种多环芳烃

建立气相色谱–质谱法同时测定聚氨酯塑胶跑道中16种多环芳烃如萘、苊、二氢苊、芴、菲、蒽、荧蒽、苯并[b]荧蒽、芘、苯并[a]蒽、屈、苯并[k]荧蒽、苯并[a]芘、茚并[1,2,3-cd]芘、1-甲基奈、2-甲基萘的检测方法。样品采用甲苯为提取剂,经超声提取和硅胶柱净化后,用气相色谱–质谱法测定16种多环芳烃残留量。16种多环芳烃的质量浓度在0.2~10.0 mg/kg范围内与色谱峰面积呈良好的线性,线性相关系数r20.998,检出限为5.0~60.0μg/kg。回收率为72.4%~101.6%,测定结果的相对标准偏差为0.9%~7.2%(n=6)。该方法准确度高、精密度好,适用于聚氨酯塑胶跑道中多环芳烃多残留检测。     

吹扫捕集-气相色谱-质谱法测定水中10种半挥发性有机物

提出了吹扫捕集-气相色谱-质谱法测定水中硝基苯、三氯苯、硝基氯苯、四氯苯、六氯苯等10种半挥发性有机物含量的方法。选择吹扫温度和吹扫时间分别为60℃和8min。在气相色谱分离中用DB-5MS毛细管色谱柱为固定相,在质谱分析中采用全扫描监测模式,内标法定量。10种半挥发性有机物的线性范围均为0.5~20μg·L-1,检出限(3S/N)在0.005 9~0.073μg·L-1之间。以地表水、生活污水和工业废水为基体做加标回收试验,测得10种半挥发性有机物的回收率在80.4%~105%之间,测定值的相对标准偏差(n=6)在2.4%~16%之间。     

气相色谱-串联质谱检测烟草中15种苯氧羧酸类除草剂残留

建立了气相色谱-串联质谱技术对烟草中15种苯氧羧酸类除草剂农药残留量的分析方法。样品采用乙腈提取、Carbon TPT固相萃取柱净化、三甲基硅烷化重氮甲烷衍生化,采用气相色谱-串联质谱对15种苯氧羧酸类除草剂进行测定,通过保留时间、选择离子及相对丰度定性,外标法定量。结果表明,15种苯氧羧酸类除草剂在20~1 000μg/L浓度范围内均呈良好线性关系,相关系数大于0.992,检出限为0.9~3.3μg/kg,定量下限为3.2~10.8μg/kg。在20,100,200μg/kg 3个加标水平下的平均回收率为71.5%~105.6%,相对标准偏差(RSD)为4.5%~14.9%。该方法简便、快速、灵敏,适用于烟草中15种苯氧羧酸类除草剂的同时检测。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.