Quadrupole field in hairpin-type cathode gun and mechanism of axial-astigmatism production

Mechanism of axial astigmatism production in the hairpin-type cathode gun was investigated by numerical calculation. The electrostatic potential in the gun was first decomposed into the axially symmetric and quadrupole components, and then the trajectory behavior was investigated by the generalized trajectory method. The axial astigmatism of the hairpin-type cathode gun was found to depend strongly on the Wehnelt voltage; it is small as long as the Wehnelt voltage is close to cutoff condition but starts to increase rapidly when the drive voltage exceeds a certain threshold. The reason for a negligible axial astigmatism at or close to the cutoff lies in the mutual dependence of the tip electric field intensity and the quadrupole field strength near the cathode. The tip quadrupole field strength is given by the product of the tip field intensity and the difference in the cathode curvature in the two orthogonal cross sections. A negligible axial astigmatism of the hairpin-type cathode gun in usual operations is due to a small quadrupole field close to the cutoff condition where the tip field is weak.     

Experimental and theoretical investigations into the electronic structure of CF2Br2 by electron momentum spectroscopy

The binding energy spectra and electron momentum density distributions for the valence orbitals of CF₂Br₂ have been obtained by using electron momentum spectroscopy (EMS) at an impact energy of 1200 eV plus binding energy. The measured electron momentum profiles are compared with Hartree–Fock (HF) and density functional theory (DFT) calculations with different-sized basis sets. In general, the DFT-B3LYP calculation using the large basis sets of 6-311++G** and aug-cc-pVTZ fairly describe the experimental results. Moreover, the controversial orderings of the outer valence orbitals have been reassigned. The pole strength of the main ionization transition from the inner valence orbital of 1b₂ is determined.     

Intense laser field effects on the electron Raman scattering in a strained InGaN/GaN quantum well

The differential cross-section for an intersubband electron Raman scattering process in a strained InGaN/GaN quantum well in the presence of an intense laser field is studied. In the effective-mass approximation, the electronic structure is calculated by taking into account the effects of spontaneous and piezoelectric polarization fields on the confinement potential. Effects of laser field strength, indium composition and the well width on the differential cross-section of the strained quantum well are investigated. Results show that the position and the magnitude of the peaks of emission spectra considerably depend on the laser field strength as well as structural parameters.     

重复频率强流电子束的产生和传输实验研究

 电子束真空二极管重复频率运行时,它将表现出与单次运行时不同的特点。在电子束产生过程中,屏蔽半径应尽可能地小,且击穿延时时间较短,故选择石墨作为阴极材料。实验结果表明：在重复频率运行时,当环型阴极环厚较薄时,阴极的发射电流密度较大,因此对阴极的加热效应也加强,等离子体的膨胀速度加快,从而使得二极管阻抗减小,最后几次输出的电子束的电流较大,而电压减小;当重复频率较高时,由于加热效应使得阴极等离子体膨胀速度加快,最后几个脉冲阴极发射能力增强,波形重复性变差;当引导磁场强度增大时,阴极等离子体受到较大的磁场力约束,横向膨胀速度减慢,从而使得电子发射面积减小,总发射电流减小,二极管的阻抗增大。最后取引导磁场为1.5 T,阴极环厚为1 mm,得到重复频率100 Hz、束压827 kV、束流8.22 kA、脉冲波形之间重复性很好的均匀电子束输出。     

Quantum transport in carbon nanoscrolls

The transport properties of carbon nanoscrolls in a uniform electric field are investigated by using the Landauer-Buttiker formula. The energy dispersions depend sensitively on the geometry and the field strength. The bandgaps may become zero and exhibit the semiconductor-metal transitions. Variations in the electronic structures with the geometry or the field strength are reflected in the conductance. The conductance exhibits a stepwise behavior, caused by the discrete number of quantized channels contributing to transport. The shoulders of the conductance are stretched out as temperature rises.     

һ�ּ򵥵ĻԹ�ŵ����������Ϸ���

以碰撞为能量交换机制,按局部热力学平衡近似处理低气压等离子体,并考虑辉光放电二极之间的电位分布,得到了电子密度与气体压力的关系和电子温度与电场强度的关系。提出了一种利用压强、电压和电流就获得电子温度和密度的诊断方法。用Langmuir探针方法验证了获得的结果。     

Electron transport through asymmetric DNA molecules

We investigate quantum mechanical electron transport along the long axis of the DNA molecule using an effective tight-binding model. The overall contour plot of transmission, the current-voltage characteristics, and the differential conductance are examined for the variation of backbone onsite energy, the energy-dependent hopping strength, and the contact coupling between the leads and the DNA molecule. It is shown that as backbone asymmetry increases, the merging and collapse of the two mini-bands take place and an extra resonance peak in the transmission appears. In addition, we present the modulation of voltage threshold in the current-voltage curves and a double-peak structure in the differential conductance due to the disappearance of the merged mini-band. Finally, in the Coulomb blockade regime of asymmetric contact coupling, a distinct and under-unity resonance in the transmission appears due to the interference effects between the DNA molecular bands and the electronic structure of the leads at the DNA-lead interface.     

Electron transport of a quantum wire with spatially periodic spin–orbit coupling

Electron transport properties of an ideal one-dimensional (1D) quantum wire are studied including spatially periodic Rashba spin–orbit coupling (SOC) and Dresselhaus SOC. By comparing with the previous work [S.J. Gong, Z.Q. Yang, J. Phys. Condens. Matter 19 (2007) 446209], two transmission gaps appear in the transmission probability of electrons and their widths are also broadened dramatically. Moreover, it is found that their widths are sensitive not only to the strength of SOCs but also to the length ratio of SOCs segment and non-SOCs segment. In addition, a ‘circle-type’ transmission behavior has been found by tuning the strength of SOCs continuously. Our results may extend the previous work and provide an more effective method to manipulate the current in nanoelectric devices.     

一种简单的辉光放电等离子体诊断方法

以碰撞为能量交换机制,按局部热力学平衡近似处理低气压等离子体,并考虑辉光放电二极之间的电位分布,得到了电子密度与气体压力的关系和电子温度与电场强度的关系。提出了一种利用压强、电压和电流就获得电子温度和密度的诊断方法。用Langmuir探针方法验证了获得的结果。     

Temperature dependence of the electric field gradient in GaN measured with the PAC-probe 181Hf

A radial inhomogeneous magnetic field produced by counter-propagating currents in anti-Helmholtz configuration coils has been superimposed to a Penning trap. The confinement properties of electrons in such a trap have been studied experimentally. Without the radial B-field we find a number of operating conditions where instabilities occur, arising from higher order contributions to the quadrupolar trapping field. When we apply the radial field the trap properties remain essentially unchanged until the strength of this field at the boundary of the electron cloud is of the same order as the homogeneous Penning field. Then a sudden breakdown in the confinement appears. The experiments have been performed in low magnetic fields. The equations of motions of the trapped particles can be cast in a dimensionless form and our results can be considered as independent of the field strength. Contribution was presented at the TCP06, Vancouver Island, 2006.     

Filamentation of a rotating electron beam in a magnetized plasma

Filamentation of a nonrelativistic rotating electron beam in a magnetized plasma is investigated by solving the kinetic equation and finding its dielectric permitivity. The period and the establishment time of the filamentation structure and threshold for instability development are obtained. It will be shown that only when the external magnetic field strength becomes smaller than a characteristic value, filamentation appears.     

合肥光源储存环聚焦模型标定

 描述了利用轨道响应矩阵拟合技术标定合肥光源储存环聚焦模型的过程及实验结果。通过响应矩阵分析,得到了合肥光源储存环弯铁边缘聚焦强度约为0.1 mrad/A,场积分为0.62~0.63,考虑了四极铁聚焦强度的修正系数的影响,发现了原四极铁磁测数据中较大的系统偏差,分析结果和备用磁铁的磁场测量数据吻合良好。在此基础上建立的合肥光源储存环理论模型可以准确地描述实际储存环线性光学特性。     

HIRFL-CSR实验环电子冷却装置磁场测量

 在HIRFL-CSR实验环电子冷却装置上采用了独立的高精度螺线管串联产生纵向磁场的设计,获得很高的冷却段磁场平行度。使用霍尔片测量磁场的分布,使用磁针测磁方法测量冷却段磁场的磁轴偏角,并根据测量及计算结果对单个线圈磁轴进行微调。测量及调试结果表明,在施加电流为额定电流的一半时,冷却段磁感应强度为0.078 T,剩余磁场小于2×10^-4 T,磁场不平行度小于1×10^-4,达到了预期的设计目标。     

Optical fiber cables using V-grooved cylindrical units: High performance cables

Some practical and theoretical aspects of a V-grooved cylindrical cable (high performance optical fiber cable) are now being developed in several countries. Design of cables is important, because bendings may cause distortions. In order to limit micro-bending losses in an optical fiber cable, it is possible to modify parameters relating to the fiber or the cable. Some of the possibilities are: to decrease the core diameter in order to decrease the attenuation coefficient; to increase the diameter of the cladding so as to increase the tension above which micro-bendings occur; to increase the continuous bending radius due to cabling; to decrease the effects of roughness (μ); to integrate the effects of roughness as much as possible by decreasing the Young modulus of the coating and of the cable material and by increasing the cladding thickness; and to suppress the tension T of the fiber in the cable. The cabling element is made of a V-grooved cylindrical core, in which the fiber with an outside diameter d_e (outside diameter or primary coating) are laid without tension, with a slight excess length. The slots with a depth h are helical or alternated helical, providing the possibility of additional excess length, and the fiber can be “cabled” directly without stresses. A central strength member with a diameter Dp reinforces the cylindrical rod, ensuring the mechanical and thermal qualities.     

Electron beam induced modifications in crystalline structure of polyvinylidene fluoride/nanoclay composites

PVDF/nanoclay nanocomposites were prepared via melt mixing method. The intercalated dispersion of the nanoclay in PVDF matrix was confirmed by XRD. According to FTIR, DSC and XRD results, the presence of nanoclay facilitated transition from α-to-β crystalline phase. Electron beam irradiation decreased the melting point of the nanocomposites. The decrease in melting point of the nanocomposites was about 11 °C at 500 kGy. The crystallinity of nanocomposites increased at an irradiation dose of 100 kGy and decreased at higher irradiation doses. The extent of crosslinking of the nanocomposites increased significantly with irradiation up to 300 kGy. The nanoclay intensified the increase in yield strength with irradiation doses up to 300 kGy. The combination of nanoclay and irradiation had a synergistic effect on the increase of yield strength.     

Unstable plasma characteristics in mirror field electron cyclotron resonance microwave ion source

Electron cyclotron plasma reactor are prone to instabilities in specific input power [3–7] region (150–450 watts). In this region power absorption by gas molecules in the cavity is very poor and enhanced input power gets reflected substantially without increasing ion density. There are abrupt changes in plasma characteristics when input power was decreased from maximum to minimum, it was observed that reflected power changed from <2% to ∼50%. Minimum two jumps in reflected power were noticed in this specific power region and these appear to be highly sensitive to three stub tuner position in the waveguide for this particular input power zone. Unstable plasma region of this source is found to be dependent upon the magnetic field strength. Some changes in reflected power are also noticed with pressure, flow and bias and they are random in nature.     

高压直流连续波光阴极注入器中电子束流发射度研究

 高平均功率自由电子激光研究中，电子束质量是关键。针对高平均功率自由电子激光目标参数，提出了直流高压连续波光阴极注入器，给出了注入器的束流动力学过程。为了降低输出束流横向发射度，采用特殊结构设计的静电加速腔，加速电压1MV，最大加速梯度10MV/m。用PARMELA程序进行了粒子动力学模拟，电子束束团电荷为0.5nC，束团长度10ps时，注入器输出束流归一化发射度均方根值为5.8mm·mrad。     

Time-dependent electron transport in HgTe/CdTe quantum wells

Based on the Floquet theory and Keldysh's nonequilibrium Green's function methods, we study the electron transport through the HgTe/CdTe quantum wells (QWs) irradiated by a monochromatic laser field. We find that when the laser field is applied, the edge states are split into a series of sidebands. When the Fermi level lies among these sidebands, the quantized plateau of the conductance is destroyed. Instead, the conductance versus the radiation frequency exhibits the successive oscillation peaks corresponding to the resonant tunneling through the sidebands of the edge states. The resonant interaction between the quasiparticles and the radiation field opens the gaps in the crossing region of the sidebands, which can be tuned by the radiation strength and frequency. This leads to the shift of the oscillation peaks in the conductance. We also show that the amplitudes of the oscillation peaks in the conductance are governed by the radiation strength and frequency.     

120 MW束流功率速调管电子枪设计

 速调管电子枪是速调管重要部件之一,它为速调管高频腔提供直流电子注。对国产50 MW速调管电子枪束流光学系统进行了模拟分析,并对电子枪陶瓷筒进行了重新设计和优化。为了在国产30 MW速调管的基础上设计50 MW速调管,采用进口钡钨电子枪阴极来减小蒸发和抑制打火,将电子注电压提高到320 kV,电流和导流系数分别为346 A和1.91 μp,以满足速调管功率提高的需要。设计出低电场强度（22.1 kV/mm）电子枪新结构,即在不影响电子枪内部束流稳定的前提下,将陶瓷筒设计成靠近阴极端半径较大而远离阴极端半径较小的形状,以避免高功率运行致使陶瓷筒的损坏。     

空气中激光烧蚀Cu产生等离子体发射光谱的研究

利用Q-开关Nd:YAG激光器产生的1.06 μm、10 ns的脉冲激光聚焦在空气中的Cu靶上,观测了激光诱导的Cu等离子体发射光谱.采用不同的激光能量,分析了波长范围为440 nm到540 nm的空间分辨发射光谱.在局部热力学平衡(LTE)条件近似下,根据谱线的相对强度,得到了等离子体电子温度约在104 K以上,给出了靶面附近电子温度的空间演化规律,并探讨了N(Ⅱ)500.52 nm谱线的谱线强度和半高全宽随激光能量的变化规律.