环空流道液流失速水击特性及其成因的研究

环空流道与圆管的结构差异,使得其失速水击特性及其成因亦有不同。为了对其进行分析研究,利用PIV对套管环空和圆管流水击流场进行拍摄,并通过Tecplot显示流场,提取轴向速度和径向速度、等速度线等参数加以分析;同时采用高精度智能动态压力传感器采集了套管环空内、外壁及内管内壁压力,对环空中水击特性进行了进一步研究。结论是:水击发生时环空断面外壁面水击压力大于内壁面水击压力;同初速情况下环空液流水击压力大于圆管流水击压力;环空中水击压力衰减速度快于圆管中;涡流是水击压力衰减以及速度变化的主要因素;水击压力振荡变化主要是压力涡流引起的断面能量的相互转化形成的。     

Stereo PIV measurement of a finite, flapping rigid plate in hovering condition

Qualitative and quantitative flow visualizations were performed on a flapping rigid plate to establish a quantitative method for flow observation and evaluation of the force in the near field of a flapping wing. Flow visualization was performed qualitatively with dye visualization and quantitatively with velocity measurements using stereo particle image velocimetry (PIV) on three planes near the tip of the plate along its chord and oriented normally. By ensemble averaging the velocity fields of the same phase angles, they represent a portion of the volume near the tip. Measurements were conducted with two flapping frequencies to compare the flow structure. The second invariant of the deformation tensor visualized the leading edge and mid-chord vortices around the plate appearing due to flow separation behind the plate while other vortical structures were visualized by streamlines. These structures appear to be related to the dynamics of the leading edge vortex. Force analysis by integrating the phase-averaged velocity field within a chosen control volume showed increases in the maxima of the magnitudes of the non-dimensional unsteady force terms on the edge of the plate at the angles after the end of each stroke. The non-dimensional phase-averaged momentum flux was similar for both flapping frequencies.     

Three-dimensional vortex formation on a heaving low-aspect-ratio wing: Computations and experiments

This paper addresses by means of high-resolution numerical simulations and experimental quantitative imaging the three-dimensional unsteady separation process induced by large-amplitude heaving oscillations of a low-aspect-ratio wing under low-Reynolds-number conditions. Computed results are found to be in good agreement with experimental flow visualizations and PIV measurements on selected cross-flow planes. The complex unsteady three-dimensional flow structure generated during dynamic stall of the low-aspect-ratio wing is elucidated. The process is characterized by the generation of a leading-edge vortex system which is pinned at the front corners of the plate and which exhibits intense transverse flow toward the wing centerline during its initial stages of development. This vortex detaches from the corners and evolves into an newly found arch-type structure. The legs of the arch vortex move along the surface toward the wing centerline and reconnect forming a ring-like structure which is shed as the next plunging cycle begins. Vortex breakdown, total collapse and reformation of the wing tip vortices are also observed at various stages of the heaving motion. At the relatively high value of reduced frequency considered, these basic flow elements of the complex three-dimensional dynamic stall process are found to persist over a range of Reynolds numbers.     

An engineering approach to blade designs for low to medium pressure rise rotor-only axial fans

Low to medium pressure rise axial fan equipment of the arbitrary vortex flow rotor-only type is widely used in industrial and commercial applications, with many of the installations and rotor designs being far from optimum. Complex computational methods exist for analyzing flows in, for example, high-speed axial flow compressors with multistage blade rows; however, the designers and manufacturers of low-speed, general-purpose axial flow fan equipment have been reluctant to embrace this technology. A simpler yet reliable design technique is presented that allows this category of ducted axial fan rotors, in the presence of swirl-free inlet flow, to be designed to achieve a specified duty with sufficient accuracy for engineering purposes. Practical blade design recommendations and limits, similar to those that exist for free vortex flow axial rotors, have been established for the arbitrary vortex flow rotor-only case.

The technique employs a straightforward engineering approach to arbitrary vortex flow axial fan rotor design, and the equation set can be solved by using relatively simple numerical methods. Estimates of pressure rise and shaft power characteristics for a proposed fan/rotor design can be computed and the design loop iterated until an acceptable set of blade parameters is identified. It is also possible to analyze the performance of an existing axial fan installation as a prelude to the design of a more efficient and effective replacement rotor.

Experimental data used in validating the design and analysis techniques are also presented. These data include comprehensive Cobra pressure probe surveys of local flow parameters downstream of three different low boss ratio, low solidity, arbitrary vortex flow rotors (all with circular arc camber line type blades) as well as fan performance characteristics for one of the experimental rotors configured as a direct-exhaust fan unit. Installation-dependent factors such as direct-exhaust losses and tip clearance effects are also examined. The analytical technique is shown to provide acceptable estimates of fan/rotor pressure rise performance and shaft power characteristics over a moderately wide range of blade angles and operating conditions.     

Visualization of compressible vortex rings using the background-oriented schlieren method

In this article, we attempt to validate flow visualization using the high-speed background-oriented schlieren (HiBOS) method, which is the BOS technique combined with a high-speed video camera as the recording device in the experiment. The method has been applied to shock-induced flow near the open end of a shock tube. Three incident shock Mach numbers were examined so that the BOS measurements could be compared with results given in the literature of particle-image velocimetry (PIV) measurements. Using the HiBOS technique, we were able to clearly view developing, compressible vortex rings and diffracted shock waves discharged from the open end of the shock tube. From the BOS images, we extracted the history of the propagation velocity, the diameter of the vortex ring, and the diameter of the vortex core, all of which agree with the corresponding PIV values reported in the literature.     

PIV measurement of internal flow characteristics of very low specific speed semi-open impeller

Detailed particle-image velocimetry (PIV) measurements of flow fields inside semi-open impellers have been performed to understand better the internal flow patterns that are responsible for the unique performance of these centrifugal pumps operated in the range of very low specific speed. Two impellers, one equipped with six radial blades (impeller A) and the other with four conventional backward-swept blades (impeller B), are tested in a centrifugal pump designed to be operated at a non-dimensional specific speed of n_s=0.24. Complex flow patterns captured by PIV are discussed in conjunction with the overall pump performance measured separately. It is revealed that impeller A achieves higher effective head than impeller B even though the flow patterns in impeller A are more complex, exhibiting secondary flows and reverse flows in the impeller passage. It is shown that both the localized strong outward flow at the pressure side of each blade outlet and the strong outward through-flow along the suction side of each blade are responsible for the better head performance of impeller A.     

Investigation of the flow in a circular cavity using stereo and tomographic particle image velocimetry

The turbulent flow over a circular cavity with an aspect ratio of D/H = 2 is investigated by multi-planar stereoscopic particle image velocimetry and with tomographic particle image velocimetry (PIV). The main aim of the study is the flow topology and the turbulent structure of the asymmetrical flow pattern that forms inside the cavity at these specific conditions. The flow field is measured in the vertical symmetry plane to describe the overall recirculation pattern in the cavity and the turbulent shear layer developing from the separation point. In this specific regime the shear layer fluctuations are recognized as those caused by instabilities together with the effect of the incoming boundary layer turbulence. Additional observations performed at several wall-parallel planes at different height inside the cavity allow to further evaluate the secondary flow circulation generated by this asymmetric regime. The observed flow pattern consists of a steady vortex, occupying the entire cavity volume and placed diagonally inside the cavity such to entrain the external flow from one side, capture it into a circulatory motion and eject it from the opposite side of the cavity. The spatial distribution of the turbulent fluctuations also reveals the same structure. The tomographic PIV measurement returns a visual inspection to the instantaneous three-dimensional structure of the turbulent fluctuations, which at the investigated height exhibit a low level of coherence with slightly elongated vortices in the recirculating flow inside the cavity.     

Time-resolved particle imaging velocimetry for the investigation of rotating stall in a radial pump

The operating range of turbomachines is limited in terms of the low flow rate by instabilities appearing in flow-leading parts of the machinery resulting in the creation of vortices. If the flow is further throttled, stall cells can start to propagate in the impeller at a fraction of the rotor speed. This article presents an investigation of rotating stall at different flow rates in a radial pump using time-resolved particle imaging velocimetry (PIV). This technique was used to investigate the flow field at the same position in every channel of the impeller during several revolutions. Frequency analysis was applied to the measured velocities to calculate the angular speed of the rotating stall in the impeller. The interest of time-resolved PIV to understand rotating stall is demonstrated, as it allows measurement of transient, irregularly appearing flow fields.     

Application of particle image velocimetry to a transonic centrifugal compressor

As part of an ongoing research project the performance and internal flow field of a high-pressure ratio centrifugal compressor is being investigated. Based on previous, primarily, point-wise laser-optical measurements the compressor was redesigned and resulted in an improved impeller and diffuser with a single-stage pressure ratio of 6:1 at 50,000 rpm. Current research activities involve the use of particle image velocimetry (PIV) to analyze and further improve the understanding of the complex flow phenomena inside the vaned diffuser given the capability of PIV of capturing spatial structures. The study includes phase-resolved measurements of the flow inside a diffuser vane passage with respect to the impeller blade position. Both, instantaneous and phase-averaged velocity fields are presented. The flow field results obtained by PIV are to be used for future validation of the related CFD calculations, which in turn are expected to lead to further improvements in compressor performance. In addition, the potential of stereo PIV for this type of turbomachinery application could be successfully demonstrated.     

Scanning PIV measurements of a laminar separation bubble

Scanning PIV is applied to a laminar separation bubble to investigate the spanwise structure and dynamics of the roll-up of vortices within the bubble. The laminar flow separation with turbulent reattachment is studied on the suction side of an airfoil SD7003 at Reynolds numbers of 20,000–60,000. The flow is recorded with a CMOS high-speed camera in successive light-sheet planes over a time span of 1–2 s to resolve the temporal evolution of the flow in the different planes. The results show the quasi-periodic development of large vortex-rolls at the downstream end of the separation bubble, which have a convex structure and an extension of 10–20% chord length in the spanwise direction. These vortices possess an irregular spanwise pattern. The evolution process of an exemplary vortex structure is shown in detail starting from small disturbances within the separation bubble transforming into a compact vortex at the downstream end of the separation bubble. As the vortex grows in size and strength it reaches a critical state that leads to an abrupt burst of the vortex with a large ejection of fluid into the mean flow.     

Three-dimensional temporally resolved measurements of turbulence–flame interactions using orthogonal-plane cinema-stereoscopic PIV

A new orthogonal-plane cinema-stereoscopic particle image velocimetry (OPCS-PIV) diagnostic has been used to measure the dynamics of three-dimensional turbulence–flame interactions. The diagnostic employed two orthogonal PIV planes, with one aligned perpendicular and one aligned parallel to the streamwise flow direction. In the plane normal to the flow, temporally resolved slices of the nine-component velocity gradient tensor were determined using Taylor’s hypothesis. Volumetric reconstruction of the 3D turbulence was performed using these slices. The PIV plane parallel to the streamwise flow direction was then used to measure the evolution of the turbulence; the path and strength of 3D turbulent structures as they interacted with the flame were determined from their image in this second plane. Structures of both vorticity and strain-rate magnitude were extracted from the flow. The geometry of these structures agreed well with predictions from direct numerical simulations. The interaction of turbulent structures with the flame also was observed. In three dimensions, these interactions had complex geometries that could not be reflected in either planar measurements or simple flame–vortex configurations.     

Stereoscopic multi-planar PIV measurements of in-cylinder tumbling flow

The non-reacting flow field within the combustion chamber of a motored direct-injection spark-ignition engine with tumble intake port is measured. The three-dimensionality of the flow necessitates the measurement of all three velocity components via stereoscopic particle-image velocimetry in multiple planes. Phase-locked stereoscopic PIV is applied at 15 crank angles during the intake and compression strokes, showing the temporal evolution of the flow field. The flow fields are obtained within a set of 14 axial planes, covering nearly the complete cylinder volume. The stereoscopic PIV setup applied to engine in-cylinder flow and the arising problems and solutions are discussed in detail. The three-dimensional flow field is reconstructed and analyzed using vortex criteria. The tumble vortex is the dominant flow structure, and this vortex varies significantly regarding shape, strength, and position throughout the two strokes. The tumble vortex center moves clockwise through the combustion chamber. At first, the tumble has a c-shape which turns into an almost straight tube at the end of the compression. Small-scale structures are analyzed by the distribution of the turbulent kinetic energy. It is evident that the symmetry plane only represents the 3D flow field after 100 CAD. For earlier crank angles, both kinetic energy (KE) and turbulent kinetic energy (TKE) in the combustion chamber are well below the KE and TKE in the symmetry plane. This should be taken into account when the injection and breakup of the three-dimensional fuel jet are studied. The mean kinetic energy is conserved until late compression by the tumble motion. This conservation ensures through the excited air motion an enhancement of the initial air-fuel mixture which is of interest for direct-injection gasoline engines.     

Flows around rotating disks with and without rim-shroud gap

Experimental and numerical approaches have been used to study the effect of the radial rim-shroud gap on the flow structures found around a rotating disk in a finite cylindrical casing. When the radius of the disk and the inner radius of the casing are comparable and there is no radial gap, instabilities bring spiral rolls with a positive front angle in the Bödewadt layer on the end wall of the stationary casing. When the disk radius is smaller than the inner radius of the casing, vortex flows appear within the radial gap between the disk rim and the side wall of the casing. If the disk is thin, but not too thin, disturbances generated by these vortex flows proceed inward and the spiral rolls with a negative front angle appear in the Bödewadt layer. In the case of a thick disk, wavy Taylor vortex-like flow appears in the radial gap. The disturbances formed by the vortex flow do not well propagate into the inner region, and a flow pattern of bead-like vortices or a chain of vortices consisting of a series of small vortices are found around the disk in the visualized figure parallel to the disk.     

Structure of Tip Leakage Flow in a Forward-Swept Axial-Flow Fan

An experimental analysis using three-dimensional laser Dopplervelocimetery (LDV) measurements and computational analysis usingthe Reynolds stress model of the commercial code, FLUENT, wereconducted to give a clear understanding on the structure of thetip leakage flow in a forward-swept axial-flow fan operating atthe peak efficiency condition, and to emphasize the necessity ofusing an anisotropic turbulence model for the accurate predictionof the tip leakage vortex. The rolling-up of the tip leakage flowwas initiated near the position of the maximum static pressuredifference, which was located at approximately 12% axial tipchord downstream from the leading edge of the blade, and developedalong the centerline of the pressure trough on the casing. Areverse flow between the blade tip and the casing due to the tipleakage vortex acted as a blockage on the through-flow. As aresult, high momentum flux was observed below the tip leakagevortex. As the tip leakage vortex proceeded to the aft part of theblade passage, the strength of the tip leakage vortex decreaseddue to the strong interaction with the through-flow and the casingboundary layer, and the diffusion of the tip leakage vortex byhigh turbulence. Through the comparative study of turbulencemodels, it was clearly shown that an anisotropic turbulence model,e.g., Reynolds stress model, should be used to predict reasonablyan anisotropic nature of the turbulent flow fields inside the tipleakage vortex. In comparison with LDV measurement data, thecomputed results predicted the complex viscous flow patternsinside the tip region in a reliable level.     

Eclatement tourbillonnaire dans une cavité rotor–stator cylindrique

The rotating flow inside an enclosed cylindrical rotor–stator cavity is studied. Within a certain range of governing parameters, vortex breakdown phenomenon can arise along the axis. Very recent papers exhibiting some particular three-dimensional effects, have concentrated new interest on this topic. The study is carried out by a numerical resolution of the 3D Navier–Stokes equations, based on spectral approximations. Three-dimensional behaviours of the flow and in the structure of the associated vortex breakdown are numerically exhibited for the first time in a cavity of large axial aspect ratio.     

Vibrations of a cylinder in a uniform flow in the presence of a no-slip side-wall

A circular cylinder placed in a uniform flow, and that spans the entire length between two side walls, may experience either parallel or oblique vortex shedding depending on the end conditions. It was shown by Mittal and Sidharth (2014) that the spatio-temporal periodicity of the oblique vortex shedding results in constant-in-time force experienced by the cylinder. On the contrary, parallel vortex shedding leads to fluid force that fluctuates with time. The free vibrations of a circular cylinder, in the presence of a wall, are investigated. For comparison, computations with end walls, where a slip condition on velocity is specified, are also carried out. The Reynolds number, based on the diameter of the cylinder and free-stream speed of the flow, is Re=100. The initial condition for the free vibrations is the fully developed unsteady flow past a stationary cylinder with oblique shedding. It is found that as the amplitude of vibration of the cylinder builds up, the vortices shed from the cylinder align with its axis leading to parallel shedding. The response of the cylinder is associated with two branches: initial and lower. On the lower branch, the response of the cylinder is virtually identical from two- and three-dimensional computations. The flow as well as the response is different on the initial branch and outside the synchronization regime. Forced vibrations confirm the phenomena.     

Entrance effects in the channels of the parallel plate stack in oscillatory flow conditions

This paper considers an entrance flow into the channels formed by a stack of parallel plates, placed in an acoustic resonator that provides oscillatory flow forcing. Interesting complex flow phenomena around the extremity of the stack are observed, essentially due to the introduction of cross-sectional discontinuities: vortex formation and shedding during the fluid ejection from the channels and development of an entrance flow during the suction phase, when the fluid enters the channels from outside. It is the latter that is of particular interest in this study. Particle image velocimetry (PIV) is used to investigate the flow structures in the “entrance region”. Velocity profiles are measured as a function of phase angle within an oscillation period and the distance from the stack end into the channel. Using the data obtained, an “entrance length” defined by analogy with existing fluid mechanical definitions, is estimated. The experiments are supplemented by CFD calculations to improve the understanding of such entrance flows.     

Stereo particle image velocimetry applied to a vortex pipe flow

Stereo particle image velocimetry (PIV) has been employed to study a vortex generated via tangential injection of water in a 2.25 inch (57 mm) diameter pipe for Reynolds numbers ranging from 1,118 to 63,367. Methods of decreasing pipe-induced optical distortion and the PIV calibration technique are addressed. The mean velocity field analyses have shown spatial similarity and revealed four distinct flow regions starting from the central axis of rotation to the pipe wall in the vortex flows. Turbulence statistical data and vortex core location data suggest that velocity fluctuations are due to the axis of the in-line vortex distorting in the shape of a spiral.     

Conformal contour dynamics in bounded domains

A contour dynamics algorithm is presented for vortex patches in unbounded domains and in simply connected bounded domains. It is based on conformal mapping and spectral analysis. The inside and outside of a vortex patch are analytically mapped onto the inside and outside of the unit circles of two different complex planes. The flow field is determined by matching the inner and outer flows on the patch boundary. Following the Legras and Zeitlin conformal dynamics concept, the time evolution of the patch boundary is expressed by means of the time derivatives of the mapping functions. The presence of a bounding wall, which can be permeable and movable, is considered. The geometry and dynamics of the patch and the flow velocity on the bounding wall are represented by Fourier series; by assuming their coefficients as control parameters, the proposed formulation can be appealing for optimization and control purposes. Two numerical examples of the proposed technique are presented.