周向超声导波在薄壁管道中的传播研究

本文研究了薄壁管道内周向导波的传播及其频散特性，并且通过对比薄壁板与薄壁管道内的导波，找出了一个比较简便研究周向导波的方法。并通过实验验证了周向导波的频散现象以及激励模态与斜探头楔型角的关系，并且认定在管道中可以激励出单一的周向导波模态。     

周向导波在空心圆柱体中传播的数值模拟研究

在石油、化工、食品和城市供水等行业,由于腐蚀等原因而引起泄漏事故,造成巨大的经济损失和资源浪费.因此,能够预先检测到管道缺陷避免事故发生显得十分重要.基于弹性动力学理论,利用Matlab编程实现周向导波在空心圆柱体中传播的数值模拟.利用特征函数展开法计算出周向导波的频散曲线及0.6MHz和1MHz各个模态的时域波形图并据此分析激励方式同周向导波传播的关系,频率为1MHz或0.6MHz时,1和2模态在空心圆柱壳中传播的周向导波中处于主导地位:各模态的径向或周向位移幅度会受到激励入射角的影响而变化并且周向导波的位移幅度随着激励入射角的增加而增加:得到特定频率下,周向导波各模态径向、周向位移的变化关系.本文结果为进一步利用实验方法研究周向导波在空心圆柱体中传播特性和缺陷检测奠定了基础.     

磁场对电磁弹性板中Lamb波频散特性的影响

研究了静态磁场下电磁弹性结构中Lamb波的传播行为.在确定静态磁场下电磁弹性板中耦合初始广义应力(弹性应力、电位移和磁感应强度的基础上,推导了含初始广义应力时板中Lamb波传播的运动方程,并由此获得了对称模态和反对称模态时的频散方程.以由BaTiO3-CoFe2O4材料构成的电磁弹性板模型作为数值算例,绘制了Lamb波传播的对称模态和反对称模态频散曲线.计算结果表明磁场对Lamb波的频散特性有一定的影响.     

基于Lamb波频散特性的薄板声发射源定位方法研究

声发射源时差定位方法中波速的确定是定位准确的关键问题,根据模态声发射理论,声发射信号在薄板内的传播过程中具有频散现象和多模态特性.不同频率不同模态的声波其传播速度不同.基于Lamb波频散特性和声发射检测技术,采取时频联合分析方法对铝薄板中声波模式进行识别;利用低频段频散不明显的扩展波的波速和同一频率同一模态波到达两传感器的时间差来实现声发射源的准确定位;通过铝薄板中AE源定位实验表明,采用S0模式,即扩展波的波速进行定位计算,可以比较准确地确定声发射源的位置,而且理论值与实际值相差很小.     

弱界面压电／压磁层状结构中的SH波

研究了弱界面压电层/压磁半空间结构中SH波的频散特性, 界面性能由 ``弹簧'模型表征, 压电层的表面考虑电学短路和电学开路两种边界条件. 推导了显函形式的 频散方程, 并结合算例分析了界面性能和电学边界条件对SH波传播特性的影响. 数值结果表 明: 弱界面降低了SH波传播的相速度; 对于短路电边界条件, 弱界面可以使一阶模态的相速 度小于B-G表面波的速度; 对于开路电边界条件, 一阶模态的相速度总是大于剪切体波的波 速.     

Lamb波理论及层合板冲击损伤的实验研究

从理论上分析了板中Lamb波信号的传播特性,并给出Lamb波在板中传播的频散方程。理论分析及实验均表明,Lamb波的频散特性与复合材料结构损伤有着直接的联系,而且最低阶的对称和反对称Lamb波模态对层合板的损伤比较敏感,但应用Lamb波的频散效应监测结构的损伤在检测技术上还难以实现。根据板中导波形成Lamb波的共振原理,板中应力波的幅频特性很大程度上反映了Lamb波的谐振特征。因此,利用压电元件的压电阻抗谱分析应力波的各阶模态频率及振幅对结构损伤的变化,能够反映材料内部损伤与Lamb波的频散特性。文中针对表面粘贴压电元件的层合板智能结构,建立了包含Lamb波谐振模式的压电阻抗计算模型。冲击损伤试件的实验表明,由于结构损伤的出现压电阻抗谱中的模态频率及其阻抗幅值等特征信息将发生变化。因此,引入应力波损伤因子可以对结构冲击损伤的存在和程度进行初步评价。该方法基于结构的机-电动态阻抗特性,不受结构的几何形状限制,测试用的压电元件成本低,方法简单可行,有望在智能结构的健康诊断方面获得应用。     

正交各向异性板中非主轴方向的Lamb波

基于线性三维弹性理论,采用勒让德正交多项式展开法,推导了波沿正交各向异性材料非主轴方向传播时的Lamb波耦合波动方程,并对耦合波动方程进行了数值求解.为验证该方法的适用性和正确性,首先将此方法应用于各向同性材料,并与已知的数据结果进行了比较;然后以单向纤维增强复合材料为例,计算了耦合Lamb波沿不同的非主轴方向传播时的相速度频散曲线,并分别研究了传播方向改变时低阶模态Lamb波和高阶模态Lamb波频散特性的变化.最后,针对潜在用于各向异性复合材料结构健康监测的耦合Lamb波低阶模态,给出了其在不同传播方向时的相速度分布和群速度分布.同时,结合低阶模态Lamb波的位移分布特性和材料的各向异性特点,阐释了S0模态对波的传播方向变化最为敏感的原因.     

非理想界面弹性层/压电柱结构中SH波的传播特性

研究了各向同性弹性层与压电柱之间非理想连接时沿周向传播的SH波的频散特性.弹性层表面力学自由;弹性层与压电柱之间应力连续、位移间断.通过求解控制方程,将问题的解用Bessel函数表示,利用界面条件和边界条件得到频散方程,然后对其进行数值求解,分析了界面性态、材料常数和几何尺寸对SH波传播特性的影响.     

管内流体对单壁碳纳米管中弯曲波频散的影响

由于其管状结构,碳纳米管在纳机械系统中可望被用作输流管道.采用连续介质力学方法,研究管内有流体存在时碳纳米管中弯曲波的传播和频散.建立流体存在时考虑二阶应变梯度的非局部弹性Timoshenko梁方程.流体的存在,使相速度最低的解支相速度降低.当流速较低时,流速对碳纳米管中弯曲波传播的影响不大.当流速较高时,相速度最低的一支随流速增加相速度降低.当流速非常高时,该解支会消失.但流体的存在对其他解支影响不大.随着波数的升高,非局部弹性所描述的微结构对碳纳米管中弯曲波传播的影响越来越明显.     

基于谱元法考虑层间接触状态的Rayleigh波频散特征正演计算

为了提升Rayleigh波应用于成层土基勘探的精细化水平,本文基于谱元法原理,通过Goodman模型和Matsui层间滑移系数建立了可考虑层间不同接触状态的Rayleigh波理论频散方程。针对典型土基成层结构,运用谱元法和快速矢量传递解析法对比计算了层间完全连续状态下土基的Rayleigh波多阶模态频散曲线,结果显示谱元法计算结果与解析法相应结果之间的平均相对误差在0.3%以下,具有较高的计算精度。在此基础上,通过改变层间接触状态和敏感性分析,揭示了层间接触状态对Rayleigh波基阶频散特征的影响。最后,结合速度-应力有限差分数值计算,验证了谱元法计算层间不同接触状态下R波频散特征的可靠性。     

GUIDED CIRCUMFERENTIAL WAVES IN DOUBLE-WALLED CARBON NANOTUBES

A model of guided circumferential waves propagating in double-walled carbon nan- otubes is built by the theory of wave propagation in continuum mechanics,while the van der Waals force between the inner and outer nanotube has been taken into account in the model.The dispersion curves of the guided circumferential wave propagation are studied,and some dispersion characteristics are illustrated by comparing with those of single-walled carbon nanotubes.It is found that in double-walled carbon nanotubes,the guided circumferential waves will propagate in more dispersive ways.More interactions between neighboring wave modes may take place.In particular,it has been found that a couple of wave modes may disappear at a certain frequency and that,while a couple of wave modes disappear,another new couple of wave modes are excited at the same wave number.     

The thermal effect on axially compressed buckling of a double-walled carbon nanotube

The thermal effect on axially compressed buckling of a double-walled carbon nanotube is studied in this paper. The effects of temperature change, surrounding elastic medium and van der Waals forces between the inner and outer nanotubes are taken into account. Using continuum mechanics, an elastic double-shell model with thermal effect is presented for axially compressed buckling of a double-walled carbon nanotube embedded in an elastic matrix under thermal environment. Based on the model, an explicit formula for the critical axial stress is derived in terms of the buckling modes of the shell and the parameters that indicate the effects of temperature change, surrounding elastic medium and the van der Waals forces. Based on that, some simplified analysis is carried out to estimate the critical axial stress for axially compressed buckling of the double-walled carbon nanotube. Numerical results for the general case are obtained for the thermal effect on axially compressed buckling of a double-walled carbon nanotube. It is shown that the axial buckling load of double-walled carbon nanotube under thermal loads is dependent on the wave number of axially buckling modes. And a conclusion is drawn that at low and room temperature the critical axial stress for infinitesimal buckling of a double-walled carbon nanotube increase as the value of temperature change increases, while at high temperature the critical axial stress for infinitesimal buckling of a double-walled carbon nanotube decrease as the value of temperature change increases.     

Damage detection based on the propagation of longitudinal guided wave in a bimetal composite pipe

This paper investigates the damage detection based on the propagation of guided wave in bimetal composite pipes, which can identify damage locations in both axial and circumferential directions. The feasibility of the method is showed by numerical simulations using FEM code ANSYS. Mode analysis is used to evaluate the guided wave mode and its structure, which can provide the basis of the mode selection in measurements scheme. The guided wave propagation in a damaged pipe is computed by transient analysis. 16 nodes around the pipe wall, as probes, are used to record the guided wave signal. When Pseudo Margenau—Hill distribution (PMHD) for each signal is carried out, three types of modes could be found, which are led mode, excited mode and lag mode in sequences. Based on the results, the arrival time of the excited mode could be used to locate damage in axial direction, and the energy distribution around the pipe of lag mode is consistent with the damage in circumferential direction. The simulation illustrated the possibility of detecting damage location in both axial and circumferential directions based on longitudinal ultrasonic guided waves only.     

Torsional buckling of a double-walled carbon nanotube embedded in an elastic medium

The torsional buckling of a double-walled carbon nanotube embedded in an elastic medium is studied in this paper. The effects of surrounding elastic medium and van der Waals forces between the inner and outer nanotubes are taken into account. Using continuum mechanics, an elastic double-shell model is presented for the torsional buckling of a double-walled carbon nanotube. Based on the model, a condition is derived in terms of the buckling modes of the shell and the parameters describing the effect of van der Waals interaction and surrounding elastic medium. A simplified analysis is also carried out estimate the critical torque for torsional buckling of the double-walled carbon nanotube.     

Propagation of guided waves in pressure vessel

Pressure vessels usually operate under extremes of high/low temperatures and high pressures. Defect, such as crack and corrosion, can result in leakage or rupture failures, even catastrophic incidents. Guided wave-based structural health monitoring (SHM) technology is one of the most prominent options in non-destructive evaluation and testing (NDE/NDT) techniques. Propagation of guided waves in a typical pressure vessel is systematically investigated in this study for the application of guided wave-based SHM. Shape of the pressure vessel is a cylinder with two end caps. Because of geometric similarity, theory of guided wave propagation in the cylinderical structure is analyzed to study dispersive features of guided waves in the pressure vessel. Dispersion curves of three different types of guided wave modes, viz. the longitudinal, torsional and flexural modes, are calculated using theoretical method. Based on the analyses and experimental wave signals, central frequency and wave parameters of incident wave are optimized. Effect of contained liquid on propagation of guided waves, especially the L(0, 2) mode, in the pressure vessel is further investigated to minimize energy leakage of the wave to the contained liquid. The analytical method, finite element analysis (FEA) and experiments are applied to study propagation characteristics of guided waves in the pressure vessel, so as to demonstrate the feasibility of guided wave-based non-destructive evaluation and testing (NDE/NDT) for such kind of complex structures.     

厚壁管道周向导波检测技术实验研究

厚壁管道是火电机组四大管道系统的核心部件,将超声导波技术应用于厚壁管道的无损检测显得十分重要.首先确定厚壁管道检测的激励方式,优化选取适合厚壁管道检测的0.5MHz探头和楔形块角度为60°的斜探头组合.通过改变斜探头与外壁轴向缺陷之间周向距离,在一定范围内仍可检测到缺陷回波,且接收到的周向回波幅值变化不大,表明周向导波...     

厚壁管道周向超声导波缺陷检测研究

厚壁管道在特种承压设备领域中广泛使用,常规无损检测技术难以实现其快速有效地检测。本文采用数值模拟与实验相结合来研究周向导波快速检测厚壁管道的方法。首先,利用有限差分软件研究了不同角度激励下外径269mm、壁厚32mm的厚壁管道中周向导波的传播特性,优化了探头激励角度范围;然后分别制作了55°和45°的斜楔,并搭建了实验系统,研究了周向导波与厚壁管道壁厚方向不同位置缺陷的相互作用规律。研究结果表明,周向导波适用于厚壁管道快速检测。检测时需选择角度适中的探头。激发角度过小时,厚壁管中形成的周向导波模式较多,使得波包宽度较大,影响检测分辨率;而角度过大时,会使得盲区增大,导致靠近内壁区域缺陷漏检。本文的研究结论为厚壁管道缺陷周向导波的实际检测应用提供了指导。     

功能梯度圆柱板中的周向衰逝导波

与传播波模态不同,衰逝波模态波数为纯虚数或复数,它们随传播距离呈指数或阻尼式衰减.具有复波数的衰逝波对结构缺陷形状和尺寸的导波检测具有重要作用,但其求解却是非常困难的,通常要借助于各种迭代技术.论文提出一种计算求解衰逝波问题的改进的Legendre正交多项式方法,该方法可将复杂的变系数微分方程组计算转换为特征值求解问题,无需迭代便能计算得到包含实波数域、虚波数域和复波数域的完整的频散曲线.通过具体算例验证了提出方法的正确性.应用提出方法计算了不同梯度圆柱板中的衰逝导波,绘制了三维频散曲线,研究了不同径厚比和梯度场对衰逝导波频散的影响,分析了衰逝导波的位移和应力分布,讨论了衰逝导波的传播特性.     

Postbuckling prediction of double-walled carbon nanotubes under axial compression

An elastic double-shell model is presented for the buckling and postbuckling of a double-walled carbon nanotube subjected to axial compression. The analysis is based on a continuum mechanics model in which each tube of a double-walled carbon nanotube is described as an individual elastic shell and the interlayer friction is negligible between the inner and outer tubes. The governing equations are based on the Karman–Donnell-type nonlinear differential equations. The van der Waals interaction between the inner and outer nanotubes and the nonlinear prebuckling deformations of the shell are both taken into account. A boundary layer theory of shell buckling is extended to the case of double-walled carbon nanotubes under axial compression. A singular perturbation technique is employed to determine the buckling loads and postbuckling equilibrium paths. Numerical results reveal that the single-walled carbon nanotube and the double-walled carbon nanotube both have an unstable postbuckling behavior.