共查询到20条相似文献,搜索用时 0 毫秒
1.
Hyunsook Jung Hae Wan Lee 《International journal of environmental analytical chemistry》2015,95(6):569-579
In this paper, we demonstrate a robust, analytical method for the study of the initial evaporation rates of distilled sulphur mustard (HD) in concrete at various drop sizes and temperatures. We used a 5-cm wind tunnel and thermal desorption (TD) in connection with gas chromatograph and mass spectrometry detection (GC/MSD). Drops of neat HD, ranging in sizes of 1, 3, 6 and 9 µL, were applied to small concrete coupons. The temperatures were either 18°C, 25°C, 35°C or 50°C. The drop of HD rapidly spread in concrete upon its release. The initial evaporation rates of the drop of HD were analysed by TD in conjunction with GC/MSD. The results showed that the initial evaporation rates increased while HD spread over the surface of concrete, then decreased as the contamination was over. We also found that the initial evaporation rates of the drop of HD in concrete are linearly proportional to drop size and temperature. In particular, drop size or spreading factor has a more pronounced effect on the initial evaporation rates of the drop of HD in concrete than temperature. 相似文献
2.
Yidong Zhang Zhenwei Dong Lei Zhao Huijuan Guan 《Surface and interface analysis : SIA》2022,54(6):600-606
ZnO film-based ultraviolet (UV) detector was fabricated by photoassisted peak force tunnel atomic force (PFTUNA) on fluorine tin oxide (FTO) substrate. The PFTUNA current in dark and in UV light was ~0.1 and 2.0 nA, respectively. The UV sensitivity (photocurrent/dark current) is more than 20. The response time and the recovery time are ~0.12 and 0.32 s, respectively. The UV sensing mechanism is that the holes will transport to the ZnO surface to capture the adsorbed oxygen ions to weaken the depletion layer under UV illumination. The PFTUNA current between the tip and the ZnO film is consistent with the Richardson–Schottky (RS) thermionic emission model. 相似文献
3.
Kaiçar Ammous Bruno Allard Hatem Garrab Anis Ammous 《Journal of Thermal Analysis and Calorimetry》2007,90(1):307-314
In this paper, a measurement technique of losses in the switching cell, based on calorimetric technique is presented. A special
calorimeter was designed to be able to access the heat generated by an operating converter. Power component losses are studied
according to the cyclic ratio and to operating frequency and an extraction method of the different terms of these losses,
using calorimetric measurements, is presented.
An accurate expression of the switching losses in the power semiconductors devices is proposed. 相似文献
4.
O. A. F. Al-Dayel S. A. Al-Kahtani 《Journal of Radioanalytical and Nuclear Chemistry》2002,252(3):605-609
Wheat is one of the most grown crops in Saudi Arabia. It is grown in various regions of the country. Accurate knowledge of the elemental concentrations in wheat and its products (bran and flour) is of great importance from a nutritional point of view. Wheat samples were obtained from the Al-Qusim region, 300 km northwest of Riyadh, and analyzed. Up to 50 elements (Al, Sb, As, Ba, Br, Cd, Ca, Cs, Cl, Cr, Co, Cu, Ga, Au, Hf, In, I, Ir, Fe, Mg, Mn, Hg, Mo, Ni, K, Rb, Sc, Se, Ag, Na, Sr, Ta, Te, Th, Sn, Ti, W, U, V, Zn, Zr, Ce, Dy, Eu, La, Lu, Nd, Sm, Tb and Yb) were determined in the wheat products. It was observed that the elemental content of bran was much higher than that of white flour. 相似文献
5.
S. Boumsellek S. H. Alajajian A. Chutjian 《Journal of the American Society for Mass Spectrometry》1992,3(3):243-247
First results of a beam-beam, single-collision study of negative-ion mass spectra produced by attachment of zero-energy electrons to the molecules of the explosives RDX, PETN, and TNT are presented. The technique used is reversal electron attachment detection (READ) wherein the zero-energy electrons are produced by focusing an intense electron beam into a shaped electrostatic field which reverses the trajectory of electrons. The target beam is introduced at the reversal point, and attachment occurs because the electrons have essentially zero longitudinal and radial velocity. The READ technique is used to obtain the “signature” of molecular ion formation and/or fragmentation for each explosive. Present data are compared with results from atmospheric-pressure ionization and negative-ion chemical ionization methods. 相似文献
6.
7.
8.
A fast and specific method for the detection of collagenase by electrophoresis is described. The method avoids inclusion of the substrate in the resolving gel and can detect nanogram levels of the enzyme. 相似文献
9.
An evaluation of the non-boiling evaporation technique for the preconcentration of Pb, Cd, Cu, Zn at the pg g?1 level in water samples is presented. Various improvements were made to allow efficient control of contamination problems at these extremely low concentrations. They include the choice of FEP Teflon for the evaporation containers and the use of sophisticated cleaning, ageing and pre-conditionning procedures. Detailed calibration graphs were obtained down to the sub-pg g?1 level by processing ultra-low concentration standards. This technique was then applied to the determination of these four metals in snow samples collected in Greenland and Antarctica. 相似文献
10.
T. W. Ng 《Journal of Polymer Science.Polymer Physics》1997,35(6):937-943
Experimental patterns obtained using the small-angle light scattering technique for thin-film polymer studies are fraught with speckles arising from the effect of interspherulitic interference. The presence of speckles hampers efforts in characterizing the spherulitic structure. Using a divergent beam increases the number of scattering sites and results in a reduction of the degree of speckling. Nevertheless, this decimates the ability of analyzing the pattern at low-scattering angles. Employing an expanded collimated beam produces the same effect but necessitates the use of specially designed optical components. This article outlines a novel technique that involves simple vibration of the polymer sample. Experimental results confirm its efficacy in reducing speckles without limiting the ability for analysis at low-scattering angles. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35 : 937–943, 1997 相似文献
11.
In this study, the suitability of a flow-through quartz crystal microbalance system for the detection of the adhesion of rMSCs and 3T3-L1 fibroblasts on different surfaces is demonstrated. Frequency shifts for rMSCs of -6.7 mHz x cell(-1) and -2.0 mHz x cell(-1) for 3T3-L1 cells could be detected on non-modified gold sensors, revealing that the frequency shift per cell is comparable to that of a static setup. Modifying the sensor surface with SAMs of thioalkylated omega-amine-terminated PEG derivatives led to cell-adhesion-resistant surfaces. Total frequency shifts of only -20 +/- 7 Hz showed that protein adsorption was also significantly reduced. Attaching 35 pmol x mm(-2) of the GRGDS cell adhesion motif to the SAMs induced specific cell adhesion due to RGD-integrin interactions; the resonance frequency dropped by 3.4 mHz x cell(-1). Furthermore, the kinetics of cell detachment could be determined. The corresponding processes were completed after 10 min for trypsin, and not before 90 min with GRGDS. Moreover, the detectability of cell adhesion was shown to increase after the addition of manganese cations. The total decrease in the resonance frequency was almost 80 Hz in the presence of Mn(2+) (6.4 mHz x cell(-1)). [image: see text] Staining the cytoskeleton of the rMSCs shows that the GRGDS-modified surfaces are almost completely covered with well-spread cells. 相似文献
12.
Three Egyptian monazite samples from the beach black sand at Abou Khashba near Rosetta, submitted by the laboratories of the
nuclear materials authority of Egypt were analyzed for elemental contents, using Prompt gamma ray neutron activation analysis
(PGNAA) as an effective analysis technique especially for rare earth elements. An integrated system for PGNAA, located at
hot Lab. Center, has proven useful for the analytical purpose using 252Cf neutron source with neutron flux of 6.16E7 n/cm2 s, that system has been designed and calibrated for PGNAA. Sensitivity curves using different standard concentration values
of artificial liquid standards samples at different concentrations ranging from 1,000 to 5,000 mg/L in case of Sm and Gd,
while from 100 to 1,000 mg/L for Eu, have been constructed. The average concentration values for Gd, Sm and Eu in the samples
under investigation was at 1.46E4 ± 0.21, 6.683E4 ± 0.14 and 440 ± 0.18 ppm, respectively. A comparative study of the obtained
results and the results of ICP-Ms was given. 相似文献
13.
Simultaneous determination of cefoxitin,cefuroxime, cephalexin and cephaloridine in plasma using HPLC and a column-switching technique 总被引:1,自引:0,他引:1
Summary A new high performance liquid chromatographic method was developed using a column-switching technique for the simultaneous determination of cephalexin, cefuroxime, cefoxitin and cephaloridine in plasma. The plasma samples were injected onto a precolumn packed with Corasil RP C18 (37–50 m) after simple dilution with an internal standard solution in 0.01 M acetate buffer (pH 3.5). Polar plasma components were washed out using 0.01 M acetate buffer (pH 3.5). After valve switching, the concentrated drugs were desorbed in back-flush mode and separated on a Partisil ODS-3 column using acetonitrile in 0.02 M acetate buffer (pH 4.3) (1585, v/v) as the mobile phase. The method showed excellent precision with good sensitivity and speed with a detection limit of 0.5 g/ml. The total analysis time per sample was less than 25 min, and the mean coefficients of variation for intra- and inter-assay were both less than 4.9 %.This method has been successfully applied to plasma from rats after subcutaneous injection of cefuroxime. 相似文献
14.
E. V. Ermakova M. V. Frontasyeva E. Steinnes 《Journal of Radioanalytical and Nuclear Chemistry》2004,259(1):51-58
For the first time the moss biomonitoring technique has been applied to air pollution monitoring in Central Russia (Tula region). INAA at the IBR-2 reactor has made it possible to determine the content of 33 elements in mosses collected at 83 sampling site. In addition to NAA, flame AAS (atomic absorption spectrometry) was applied to determine the content of Cd, Cu and Pb. Factor analysis was applied to determine possible sources of trace element deposition in Tula mosses. The geographical distribution of factor scores and some element distribution maps over the investigated territory are presented. 相似文献
15.
Photochemical efficiency of o-quinodimethane (3) ring closure at room temperature was determined by using a time-delayed, two-color photolysis technique. o-Quinodimethane (3) was generated by the photolysis of 1,2-bis[(phenylseleno)methyl]benzene (1) by a KrF (248 nm) laser pulse and thus-generated 3 was photolyzed by a subsequent XeCl (308 nm)/XeF (351 nm) laser pulse with varying delay time of 0 to 3 s. The time profile of 3 was monitored by the chemical analyses of benzocyclobutene (5) (a photochemical product of 3), which was formed by a one-photon process, and the spiro dimer of 3 (4) (a thermal product of 3) in the two-color photolysis experiments. The time profile of 3 followed a second-order decay kinetics. The photochemical efficiency was obtained by the analysis of the delay-time dependence of the product yields; those of the consumption of 3 and the conversion 3-->5 by a single pulse of the excimer laser were 81% and 5.7% for the XeCl laser, and 73% and 2.3% for the XeF laser. This difference was attributed to the different excited states involved in the photolysis. In contrast to the photolysis of 3 in argon or rigid organic matrixes, it was revealed that photochemical conversion 3-->5 was not the main path in the solutions, and intermolecular reactions predominated. 相似文献
16.
17.
S. Perutz E. J. Kramer J. Baney C.-Y. Hui C. Cohen 《Journal of Polymer Science.Polymer Physics》1998,36(12):2129-2139
The JKR technique was used to determine the source and nature of the adhesion hysteresis present in modified poly(dimethylsiloxane) (PDMS) networks. As controlled excess amounts of the tetrafunctional crosslinker were added to the networks, the adhesion hysteresis increased. It was found that by poisoning the catalyst with a thiol the hysteresis could be significantly lowered, and completely removed in some cases. We believe that the adhesion hysteresis in this system stems from a complexation between the excess crosslinker and the catalyst. We found that the work of adhesion in this case is a function of the unloading rate. The unloading rate dependence of this chemical adhesion hysteresis was attributed to the rate of bond dissociation. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 2129–2139, 1998 相似文献
18.
Interferences in the gas phase are very unlikely and have not yet been observed with the hydride AA technique. Gas/liquid interferences between the volatile hydride forming elements and the major and minor components of low-alloy steels can be eliminated by working in the presence of higher acid concentrations and/or in acid mixtures containing nitric acid. Conditions could be found that allow the interference-free determination of the hydride forming elements in low-alloy steels directly against acid standards with detection limits around or below 0.0002%. The influence of the valence state on the determination of antimony and arsenic was investigated. 相似文献
19.
20.
C.L. Chakrabarti C.C. Wan W.C. Li 《Spectrochimica Acta Part B: Atomic Spectroscopy》1980,35(9):547-560
This paper describes a simple and rapid method for direct determination of traces of Cu, Zn, Pb, Co, Fe and Cd in the NBS oyster tissue, SRM No. 1566, by graphite furnace atomic absorption spectrometry. The solid sampling technique has been used and this results in much higher relative sensitivity by avoiding large dilution factors involved in the sample dissolution technique. The solid sampling technique also greatly reduces or eliminates serious risk of introducing contamination and/or loss of analytes involved in sample dissolution. The organic matrix of the oyster tissue is burnt off and removed by using a well-defined selective volatilization technique. Loss of Cd during charring (pyrolysis) stage is prevented by forming a relatively thermally stable compound of cadmium by adding (NH42SO4 solution to the oyster tissue sample. Also, quantitative data are presented on the effectiveness of the platform technique in removing matrix interferences. The platform technique uses an anisotropic pyrolytic graphite platform which is inserted into a commercial graphite tube. 相似文献