Preparation of a novel Ni/Co-based alloy gradient coating on surface of the crystallizer copper alloy by laser

A high wear-resistant gradient coating made of Ni/Co-based alloys on the surface of a Cu alloy substrate was synthesized using a YAG laser induced in situ reaction method. The coating consists of three layers: the first is a Ni-based alloy layer, the second and third are Co-based alloy layers. The microhardness increases gradually from 98 HV in the Cu alloy substrate to the highest level of 876 HV in the third layer. The main phase of the Co-based alloy layer is CoCr₂(Ni,O)₄, coexisting with the Fe₁₃Mo₂B₅, Cr(Co(Mo, and FeCr_0.29Ni_0.16C_0.06 phases. Wear tests indicate that the gradient coating has good bond strength and wear properties with a wear coefficient of 0.31 (0.50 for the Cu alloy substrate). Also, the wear loss of the coating is only 0.01 g after it has been abraded for 60 min, which is only one fifth of that of the Cu alloy of the crystallizer. Wear tests of the gradient coating reveal good adhesive friction and wear properties when sliding against steel under dry conditions. This novel technique may have good application to make an advanced coating on the surface of the Cu alloy crystallizer in a continuous casting process.     

Microstructure and wear properties of TiCN/Ti coatings on titanium alloy by laser cladding

Titanium carbide nitride (TiCN) reinforced Ti coating was fabricated on the surface of Ti–6Al–4V alloy by laser cladding method. Microstructure and wear properties at the surface of the coating in atmosphere were investigated. Three zones can be distinguished of the coating: the clad zone (CZ), the heat affected zone (HAZ) and the substrate. The clad zone is composed of TiCN dendrites, TiO₂ and Ti. A metallurgical bonding between the coating and the substrate was obtained. The microhardness and wear resistance of the TiCN/Ti coating are significantly improved. The average hardness of the coating is about 3 to 6 times of that of the substrate. The friction coefficients of the substrate and the coating are 0.48 and 0.34 respectively. The friction coefficient of the Ti–6Al–4V substrate was insensitive to the normal load, while that of the cladded TiCN/Ti coating was very sensitive to the normal load. The wear mass losses of the cladded samples are much lower than that of the substrate whatever the normal load is.     

Study on Fe-Al-Si in situ composite coating fabricated by laser cladding

Fe-Al-Si in situ composite coating was fabricated on the surface of ASTM A283Gr.D steel by laser cladding with the preplaced powder. The influence of powder composition, laser power and scanning speed on microstructure, microhardness and wear resistance were investigated in this paper. The results show that Fe-Al-Si in situ composite coating with the good metallurgical bond mainly consists of Fe, SiO₂ and Al₂Fe₃Si₄ intermetallic compound. With the increase of laser power and scanning speed, the grain size of coating gets the minimum value. With the increase of laser power and scanning speed, microhardness and wear resistance both get the peak vaule, and their value are three times and 3.5 times those of substrate, respectively. The optimum parameters are followed as: the ratio of the preplaced composite powder: 8:1:1, laser power: 1600 W and scanning speed: 400 mm/min.     

Broad-beam laser cladding of Al-Cu alloy coating on AZ91HP magnesium alloy

The resistance to wear and corrosion of AZ91HP Mg alloy was improved by laser cladding Al-Cu alloy. It was found that the clad layer was characterized by AlCu₄ and Mg₁₇Al₁₂ grains embedded in a AlMg matrix. The bonding zone exhibited a white-light planar crystal band with thickness of 10-13 μm. The heat-affected zone formed a eutectic structure due to the Mg diffusion. The microhardness and wear resistance of the coating were improved due to the formation of the hard phases AlCu₄ and Mg₁₇Al₁₂. Owing to the formation of dense Al₂O₃ oxide film, the coating exhibited better corrosion resistance in 3.5 wt.% NaCl solution.     

40Cr钢表面激光熔覆层的磨损性能

 为研究模具钢熔覆层的磨损性能,采用铁基粉在40Cr钢表面进行激光熔覆,以激光熔覆层为上试样,GCr15钢珠为下试样,采用HT－500磨损试验机进行摩擦磨损试验,并与40Cr基体的磨损性能相对比。利用表面形貌仪测量磨痕深度和宽度。研究结果表明：载荷小于250 g时,相同载荷下基体的摩擦系数大。载荷小于300 g时,随磨损时间延长,熔覆层、基体的摩擦系数都随着载荷增加而减小。当载荷为300 g时,基体的摩擦系数在0.563～0.589之间变化,平均值为0.576,且随时间逐渐升高,耐磨性变差;熔覆层的磨擦系数在0.431～0.457之间变化,平均摩擦系数为0.444,磨痕深度和宽度分别是0.65 mm和1.096 μm,且随时间逐渐下降,表现了良好的耐磨性能。当载荷增加到500 g时,平均摩擦系数和磨痕深度比300 g时分别增加了75％和47倍,且摩擦系数逐渐升高,磨损性能下降。     

碳化钨对激光熔覆高熵合金的影响

为了获得高性能的涂层材料,采用激光熔覆的方法,在Q235钢基体上制备了FeSiCrCoMo高熵合金涂层, 并研究了WC对高熵合金涂层的组织和性能的影响。通过金相、X射线衍射、扫描电镜、硬度计、磨损试验机分别研究了添加WC前后涂层的微观形貌、相结构、硬度及磨损性能。结果表明：高熵合金FeSiCrCoMo涂层组织为粗大枝状晶,主要由BCC相和金属间化合物构成,添加WC后,涂层中形成了致密细小的胞状晶,同时BCC相增多,金属间化合物明显减少;添加WC后涂层的硬度明显增强,平均硬度提升了23%,涂层表面平均硬度达到了687 HV0.2;WC的添加使得涂层的摩擦系数减小,磨损率减小,耐磨性能提高。     

Microstructure and properties of 6FeNiCoSiCrAlTi high-entropy alloy coating prepared by laser cladding

The content of each constituent element in the newly developed high-entropy alloys (HEAs) is always restricted in equimolar or near-equimolar ratio in order to avoid the formation of complex brittle phases during the solidification process. In this study, a 6FeNiCoSiCrAlTi high-entropy alloy coating with simple BCC solid solution phase has been prepared by laser cladding on a low carbon steel substrate. The microstructure, hardness and magnetic properties have been investigated. The experimental results show that the tendency of component segregation in the conventional solidification microstructure of multi-component alloy is effectively relieved. The microstructure of the coating is mainly composed of equiaxed polygonal grains, discontinuous interdendritic segregation and nano-precipitates. EBSD observation confirms that the polygonal grains and interdendritic segregation have similar BCC structure with lots of low angle grain boundaries at the interface. The microhardness of the coating reaches 780 HV_0.5, which is much higher than most of the HEAs prepared by other methods. In addition, the coating shows excellent soft magnetic properties.     

Composition design and laser cladding of Ni-Zr-Al alloy coating on the magnesium surface

The cluster line criterion was used for optimized design of a Ni-Zr-Al alloy used as coating on the AZ91HP magnesium alloy by laser cladding. Results show that the coating mainly consists of an amorphous, two ternary intermetallic phases with Ni₁₀Zr₇ and Ni₂₁Zr₈ type structures resulting in high hardness, good wear resistance and corrosion resistance. The interface between the clad layer and the substrate has good metallurgical bond.     

激光熔覆FeCrNiMnMoxB0.5高熵合金涂层组织与耐蚀性能

为了获得性能优异的涂层材料,采用激光熔覆的方法在Q235钢基体上制备了不同Mo含量的FeCrNiMnMoB0.5系高熵合金涂层,着重探究Mo对高熵合金组织与性能的影响。通过金相、X射线衍射、扫描电镜、硬度计、电化学工作站分别研究了高熵合金涂层的显微组织、相结构、显微硬度及耐蚀性能。结果表明：FeCrNiMnMoB0.5系高熵合金组织为树枝晶,主要由fcc相和少量金属间化合物构成。当添加少量Mo时,涂层的硬度较低,为290 HV,随着Mo的增加,晶格畸变加剧,出现少量金属化合物,涂层硬度最大增加到658 HV。在模拟饱和盐水泥浆溶液中FeCrNiMnMo0.4B0.5表现出较好的耐腐蚀性。     

Microstructure and osteoblast response of gradient bioceramic coating on titanium alloy fabricated by laser cladding

To construct a bioactive interface between metal implant and the surrounding bone tissue, the gradient calcium phosphate bioceramic coating on titanium alloy (Ti-6Al-4V) was designed and fabricated by laser cladding. The results demonstrated that the gradient bioceramic coating was metallurgically bonded to the titanium alloy substrate. The appearance of hydroxyapatite and β-tricalcium phosphate indicated that the bioactive phases were synthesized on the surface of coating. The microhardness gradually decreased from the coating to substrate, which could help stress relaxation between coating and bone tissue. Furthermore, the methyl thiazolyl tetrazolium (MTT) assay of cell proliferation revealed that the laser-cladded bioceramic coating had more favorable osteoblast response compared with the surface of untreated titanium alloy substrate.     

H13钢激光熔覆Co基涂层组织及热疲劳性能

针对热作模具用H13钢工况下易产生热疲劳失效的问题,采用Nd:YAG激光器在H13钢表面制备Co基合金涂层。利用光学显微镜、扫描电镜、能谱仪和X射线衍射仪,对涂层组织、合金元素分布及物相组成进行检测。利用显微硬度计和热震实验法,测试热疲劳对Co基合金涂层和淬火回火态H13钢硬度影响。结果表明,Co基合金涂层从底部到表层,依次为平面晶、胞状晶、树枝晶和等轴晶。Co基合金涂层物相主要由-Co和M23C6相组成,热疲劳后涂层表面形成M2O3和M3O4(M=Fe,Co,Cr)氧化物。Co基合金涂层硬度最高可达706HV0.2且呈梯度降低;热循环1000次后,Co基合金涂层表面硬度降低24.4%,H13钢表面硬度降低37.7%,Co基合金涂层硬度下降幅度低于H13钢。热循环1000次后,Co基合金涂层表面未发现明显热裂纹,H13钢表面形成大量网状热裂纹。Co基合金涂层中,Cr元素形成致密Cr2O3氧化膜使其热疲劳性能优于H13钢。     

激光熔覆TiC-Ni复合涂层的摩擦磨损性能和磨损机制研究

利用光学显微镜和扫描电镜观察了钛合金表面TiC-Ni激光熔覆层的宏观形貌和微观组织,测试了激光熔覆层的硬度、摩擦系数和磨损量。利用SEM观察了磨损的表面形貌和磨屑的形貌,分析了激光熔覆层的磨损机制。结果表明:激光熔覆层组织致密,无气孔和裂纹,硬度为基材的3倍;激光熔覆层的摩擦系数随环境压力的降低而提高,磨损量随环境压力的降低、法向载荷的增加而增加;低载时为轻微的磨粒磨损,高载时为严重的剥层磨损。     

Stress evaluation of laser cladding coating with critically refracted longitudinal wave based on cross correlation function

Research on stress evaluation of laser cladding coating with critically refracted longitudinal wave was introduced in this paper. Two critically refracted longitudinal wave transducers with 5 MHz frequency, spacing between which was constant, were employed as signal emitter and receiver. Based on acoustoelastic equation deduction, relationship between the difference in time of flight and tensile stress is obtained. Combing with cross correlation theory, the difference in time of flight between stressed and unstressed critically refracted longitudinal signals was calculated. Results show that stress evaluation is affected by layer interface and anisotropic microstructure of laser cladding coating, precision of stress evaluation of laser cladding coating increases as step length increases until it attains one cycle. In addition, influence of waveform distortion caused by microstructure of laser cladding coating on stress evaluation is discussed. At last, verification test is carried out and the experimental result is well consistent with theoretical result.     

Fabrication of nanoporous manganese by laser cladding and selective electrochemical de-alloying

Fabrication of nanoporous Cu-Mn alloy coatings was investigated by a two-step process involving high power laser cladding of a homogeneous Cu40Mn60 alloy coatings followed by selectively electrochemical de-alloying. Auger mapping results indicate that nanoporous manganese was obtained by selective electrochemical etching of the less active Cu component owing to the passivation of the more active manganese in potassium nitrate solution. The surface morphology of the porous Mn was a ribbon-like structure, different from interconnected bicontinuous nanopores that are usually obtained by de-alloying. The influence of de-alloying time, electric potential and temperature on the formation of nanoprosity is systematically investigated. Nanopore sizes can be tailored to be less than 100 nm. Under optimal etching conditions the nanopore size was below 25 nm. The surface area of the nanoporous manganese layer was enhanced by up to 990 times compared with that of a polished sample.     

Synthesis of Fe-based amorphous composite coatings with low purity materials by laser cladding

Amorphous composite coatings Fe₃₈Ni_30−XSi₁₆B₁₄V₂M_X (X = 0, 1, 2) (M contains Al, Ti, Mo, and C) were prepared with low purity of raw materials by laser cladding. X-ray diffraction and transmission electron microscopy results show that the coating have an amorphous structure with a few crystalline phase on it. The amorphous phase is the primary phase. The glass forming ability as well as the microhardness of the Fe-based alloy made from low purity raw materials can be much enhanced by adding small amount of multi-components. However, the elements addition has its optimal quantity. When X is equal to 1, the microstructure of the coating contains 97.93% amorphous phase and 2.07% crystalline phase on it. As a result, the microhardness of the coating reaches maximum. With further increasing of the additions, the amorphous phase in the coating lessens instead of augment and the crystalline phase begins to accumulate, which result in the decrease of the microhardness.     

Phase composition and tribological properties of Ti-Al coatings produced on pure Ti by laser cladding

Ti-Al coatings with ∼14.7, 18.1, 25.2 and 29.7 at.% Al contents were fabricated on pure Ti substrate by laser cladding. The laser cladding Ti-Al coatings were analyzed with X-ray diffraction (XRD), scanning electron microscope (SEM) and X-ray energy dispersive spectroscopy (EDS). It was found that with the increase of Al content, the diffraction peaks shifted gradually to higher 2θ values. The laser cladding Ti-Al coatings with 14.7 and 18.1 at.% Al were composed of α-Ti and α₂-Ti₃Al phases, while those with 25.2 and 29.7 at.% Al were composed of α₂-Ti₃Al phase. With the increase of Al content, the cross-sectional hardness increased, while the fracture toughness decreased. For the laser cladding Ti-Al coatings, when the Al content was ≤18.1 at.%, the wear mechanism was adhesive wear and abrasive wear; while when the Al content ≥25.2 at.%, the wear mechanism was adhesive wear, abrasive wear and microfracture. With the increase of Al content, the wear rate of laser cladding Ti-Al coatings decreased under 1 N normal load, while the wear rate firstly decreased and then increased under a normal load of 3 N. Due to its optimized combination of high hardness and high fracture toughness, the laser cladding Ti-Al coating with 18.1 at.% Al showed the best anti-wear properties at higher normal load.     

Laser cladding of in situ TiB2/Fe composite coating on steel

To enhance the wear resistance of mechanical components, laser cladding has been applied to deposit in situ TiB₂/Fe composite coating on steel using ferrotitanium and ferroboron as the coating precursor. The phase constituents and microstructure of the composite coating were investigated using X-ray diffraction (XRD), scanning electron micrograph (SEM) and electron probe microanalysis (EPMA). Microhardness tester and block-on-ring wear tester were employed to measure the microhardness and dry-sliding wear resistance of the composite coating. Results show that defect-free composite coating with metallurgical joint to the steel substrate can be obtained. Phases presented in the coating consist of TiB₂ and α-Fe. TiB₂ particles which are formed in situ via nucleation-growth mechanism are distributed uniformly in the α-Fe matrix with blocky morphology. The microhardness and wear properties of the composite coating improved significantly in comparison to the as-received steel substrate due to the presence of the hard reinforcement TiB₂.     

A study of Ni-based WC composite coatings by laser induction hybrid rapid cladding with elliptical spot

Ni-based WC composite coatings by laser induction hybrid rapid cladding (LIHRC) with elliptical spot were investigated. Results indicate that the efficiency using the elliptical spot of 6 mm × 4 mm (the major and minor axis of laser beam are 6 mm and 4 mm, respectively, the major axis is parallel to the direction of laser scanning) is higher than that using the elliptical spot of 4 mm × 6 mm (the major axis is perpendicular to the direction of laser scanning). The precipitated carbides with the blocky and bar-like shape indicate that WC particles suffer from the heat damage of “the disintegration pattern + the growth pattern”, whichever elliptical spot is used at low laser scanning speed. However, at high laser scanning speed, the blocky carbides are only formed if the elliptical spot of 6 mm × 4 mm is adopted, showing that WC particles present the heat damage of “the disintegration pattern”, whereas the fine carbides are precipitated when the elliptical spot of 4 mm × 6 mm is used, showing that WC particles take on the heat damage of “the radiation pattern”. Especially, the efficiency of LIHRC is increased much four times higher than that of the general laser cladding and crack-free ceramic-metal coatings can be obtained.     

Toughening of Fe-based laser-clad alloy coating

An investigation is reported on crack-free laser clad Fe-based alloy by use of biaxial powder feeding shielded with argon gas. The microstructure and phase structure of the coating were studied, and mechanical properties were analyzed through hardness, tension strength and wear resistance of the coating. Microstructure analysis showed that there was retained austenite with spherical particles distributed therein in the interdendritic and nearby grain boundary regions. The mechanical test results showed that net-like distributed retained austenite in the interdendritic region had certain toughening effect through blunting crack-tip. Under wear condition of high sliding speed and high loading, the wear resistance of the coating with net-like retained austenite was much higher than that of the coating with some discontinuous carbide network or carbide blocks. The results showed that toughening of laser clad Fe-based alloy with high hardness over 850 HV could be achieved by modifying interdendritic phases from net-like carbide to net-like austenite with spherical particles.     

40Cr钢表面激光熔覆层的磨损性能

为研究模具钢熔覆层的磨损性能,采用铁基粉在40Cr钢表面进行激光熔覆,以激光熔覆层为上试样,GCr15钢珠为下试样,采用HT－500磨损试验机进行摩擦磨损试验,并与40Cr基体的磨损性能相对比。利用表面形貌仪测量磨痕深度和宽度。研究结果表明：载荷小于250 g时,相同载荷下基体的摩擦系数大。载荷小于300 g时,随磨损时间延长,熔覆层、基体的摩擦系数都随着载荷增加而减小。当载荷为300 g时,基体的摩擦系数在0.563～0.589之间变化,平均值为0.576,且随时间逐渐升高,耐磨性变差;熔覆层的磨擦系数在0.431～0.457之间变化,平均摩擦系数为0.444,磨痕深度和宽度分别是0.65 mm和1.096 μm,且随时间逐渐下降,表现了良好的耐磨性能。当载荷增加到500 g时,平均摩擦系数和磨痕深度比300 g时分别增加了75％和47倍,且摩擦系数逐渐升高,磨损性能下降。