Experimental investigation and metallographic characterization of fiber laser beam welding of Ti-6Al-4V alloy using response surface method

In the present study, experimental investigations of fiber-laser-beam-welding of 5 mm thick Ti-6Al-4V alloy are carried out based on statistical design of experiments. The relationship between the process parameters such as welding power, welding speed, and defocused position of the laser beam with the output responses such as width of the fusion zone, size of the heat affected zone, and fusion zone area are established in terms of regression models. Also, the most significant process parameters and their optimum ranges are identified and their percentage contributions on output responses are calculated. It is observed that welding power and speed plays the major role for full penetration welding. Also, welding power shows direct effect whereas welding speed shows the inverse effect on the output responses. The bead geometry is influenced by the defocused position of the laser beam due to the change in power density on the workpiece surface. However, overall fusion zone area is unaffected. Mechanical characterization of the welded samples such as microstructural analysis, hardness, and tensile tests are conducted. It is noticed that the hardness value of the FZ is higher than the HAZ and BM zone due to the difference in cooling rate during welding which promotes the formation of α′ martensitic phase in the FZ. Also, an average hardness value in the FZ is compared for two different defocusing positions (i.e. 1 and 2 mm). It is found that hardness value is higher for 1 mm defocused position than 2 mm due the decrement in grain size below a critical range at 2 mm defocused position. The ultimate tensile strength and % elongation of the welded samples are degraded as compared to BM which can be further improved by post heat treatment.     

CO2 laser gas assisted nitriding of Ti-6Al-4V alloy

Laser gas assisted nitriding of Ti-6Al-4V alloy is carried out and nitride compounds formed and their concentration in the surface vicinity are examined. SEM, XRD and XPS are accommodated to examine the nitride layer characteristics. Microhardness across the nitride layer is measured. Temperature field and nitrogen distribution due to laser irradiation pulse is predicted. It is found that the nitride layer appears like golden color; however, it becomes dark gold color once the laser power irradiation is increased. The δ-TiN and ?-TiN are dominant phases in the surface vicinity. The needle like dendrite structure replace with the feathery like structure in the surface region due to high nitrogen concentration. No porous or microcracks are observed in the nitrided layer, except at high power irradiation, in this case, elongated cracks are observed in the surface region where the nitrogen concentration is considerably high.     

Ti-6Al-4V合金中片层组织形成的相场模拟

Ti-6Al-4V是典型的α+β钛合金,不同热处理制度和热加工工艺下可得到形貌各异的微观组织,从而表现出不同的力学性能,深刻理解合金中微观组织的形成机制有助于合金的进一步优化和改造.采用相场方法模拟Ti-6Al-4V合金中片层组织的形成及演化,以热力学数据库和动力学数据库为输入,通过计算定量预测β晶界上已存在初生α相时合金组织随时间的演化.结果表明,在一定条件下,随着时间的延长晶界α向β晶内生长形成片层组织,片状α簇的形貌与界面能各向异性密切相关;晶界取向对片层生长有重要作用,垂直于晶界生长时产生最密集的片层,随倾斜角增大片层加厚且生长缓慢;此外,热处理温度显著改变片层组织形貌,温度越高,片层尖端生长速度越慢,片层间距越大. 关键词： Ti-6Al-4V 相场模拟 片层组织     

Investigation of Ti-6Al-4V alloy acoustic softening

High power ultrasonic vibration is widely used for improving manufacturing processes such as machining and metal forming. High frequency mechanical vibration affects material properties and friction forces in contacting surfaces. Flow stress reduction under superimposed ultrasonic vibration is called as acoustic softening. The amount of this parameter should be determined for ultrasonic assisted metal forming processes. For determination of this parameter for workhorse Ti-6Al-4V alloy, experimental setup was designed and fabricated. Then tensile test under longitudinal ultrasonic vibration was performed for different ultrasonic powers. Results show that ultrasonic vibration has considerable effect on plastic behavior of the alloy and decreases flow stress. Also, increasing ultrasonic power leads to higher acoustic softening. Yield stress reduction up to 9.52%, ultimate stress reduction up to 4.55% and elongation up to 13% were obtained at 340 W ultrasonic power. After applying ultrasonic vibrations and its termination, hardness of specimens were measured in which increase up to 9% was observed.     

Surface characteristics of self-assembled microporous Ti-6Al-4V compacts fabricated by electro-discharge-sintering in air

A single electro-discharge-sintering (EDS) pulse (1.0 kJ/0.7 g), from a 300 (F capacitor, was applied to atomized spherical Ti-6Al-4V powder in air to produce microporous compact. A solid core surrounded by a porous layer was self-assembled by a discharge in the middle of the compact. X-ray photoelectron spectroscopy was used to study the surface characteristics of the compact material. C, N, O and Ti were the main constituents, with smaller amounts of Al and V. The surface was lightly oxidized and was primarily in the form of TiO₂. A lightly etched EDS sample showed the surface form of metallic Ti, indicating that EDS breaks down the oxide film of the as-received Ti-6Al-4V powder during the discharge process. The EDS Ti-6Al-4V compact surface also contained small amounts of TiN in addition to TiO₂, resulting in the reaction between nitrogen in air and the Ti substrate in times as short as 125 μs.     

Assessment of precipitates of aged Ti-6Al-4V alloy by ultrasonic attenuation

Abstract

Ti-6Al-4V alloy with different microstructures was investigated by means of ultrasonic attenuation measurements. Widmanstätten and equiaxed microstructures were obtaining by heat treating a Ti-6Al-4V alloy. These two microstructures were over-aged at 545 °C at different ageing times. In order to find out the factors affecting the variation in the ultrasonic attenuation, the heat-treated samples were examined by optical microscopy and scanning electron microscopy. Based on the theory of ultrasonic attenuation in a solid media, the mechanisms of ultrasonic attenuation in the Ti-6Al-4V alloy with different microstructures were analysed. It was found that in both cases with Widmanstätten and equiaxed microstructures, the ultrasonic attenuation increased with frequency. After ageing, the ultrasonic attenuation was mainly attributed to the scattering loss which included the stochastic and the Rayleigh scattering due to the precipitation of Ti₃Al particles homogeneously distributed in the α phase. Data analysis presented in the study showed that ultrasonic attenuation yields more accurate area fractions of precipitates predictions when a polynomial fit is performed.     

Hydrogen peroxide treatment on Ti-6Al-4V alloy: A promising surface modification technique for orthopaedic application

Ti-6Al-4V alloy was treated with various concentrations (5 wt.%, 15 wt.% and 25 wt.%) of hydrogen peroxide (H₂O₂) and then heat treated to produce an anatase titania layer. The surface modified substrates were immersed in simulated body fluid (SBF) solution for the growth of an apatite layer on the surface and the formed apatite layer was characterized using various surface characterization techniques. The results revealed that titania layer with anatase nature was observed for all H₂O₂ treated Ti-6Al-4V alloy, irrespective of the H₂O₂ concentrations. Ti-6Al-4V alloy treated with 15 wt.% and 25 wt.% of H₂O₂ induced apatite formation, however 5 wt.% of H₂O₂ treated Ti-6Al-4V failed to form apatite layer on the surface. The electrochemical behaviour of H₂O₂ treated specimens in SBF solution was studied using potentiodynamic polarization and electrochemical impedance spectroscopy. Ti-6Al-4V alloy treated with 25 wt.% of H₂O₂ solution exhibited low current density and high charge transfer resistance values compared to specimens treated with other concentrations of H₂O₂ and untreated Ti-6Al-4V alloy.     

Grain refining of Ti-6Al-4V alloy fabricated by laser and wire additive manufacturing assisted with ultrasonic vibration

The formation of the coarse columnar crystal structure of Ti-6Al-4V alloy in the process of additive manufacturing greatly reduces the mechanical performance of the additive manufactured parts, which hinders the applications of additive manufacturing techniques in the engineering fields. In order to refine the microstructure of the materials using the high intensity ultrasonic via the acoustic cavitation and acoustic flow effect in the process of metal solidification, an ultrasonic vibration technique was developed to a synchronous couple in the process of Laser and Wire Additive Manufacturing (LWAM) in this work. It is found that the introduction of high-intensity ultrasound effectively interrupts the epitaxial growth tendency of prior-β crystal and weakens the texture strength of prior-β crystal. The microstructure of Ti-6Al-4V alloy converts to fine columnar crystals from typical coarse columnar crystals. The simulation results confirm that the acoustic cavitation effect applied to the molten pool created by the high-intensity ultrasound is the key factor that affects the crystal characteristics.     

Fabrication of Zr and Zr-N surface alloying layers and hardness improvement of Ti-6Al-4V alloy by plasma surface alloying technique

Titanium alloys are very attractive materials because they have high specific strength, excellent corrosion and erosion resistance in many active environments. However, their low hardness values and poor tribological properties require improvement of their surface properties. The present study is concerned with the fabrication of Zr and Zr-N alloying layers in the surfaces of Ti-6Al-4V substrates by plasma surface alloying technique. The microstructure, chemical composition and hardness of the surface alloying layers were analyzed to understand the mechanisms of surface alloying and hardness improvement. The Zr and Zr-N surface alloying layers formed were homogeneous and compact, in which the surface alloying elements all displayed gradient distributions. The Zr and Zr-N surface alloying layers all enhanced the surface hardness of Ti-6Al-4V alloy. Zr-N surface alloying resulted in greater improvement in hardness and the maximum microhardness of (1.37 ± 0.04) × 10³ HK was obtained at the subsurface, which was much higher than that of the untreated Ti-6Al-4V alloy. The Zr-N surface alloying layer consisted of an outer nitride layer and an inner diffusion zone of Zr and N, and its very high hardness owed to the formation of the nitride layer. The mechanism of hardness improvement of Zr surface alloyed Ti-6Al-4V alloy was solid solution strengthening.     

Investigation of the voltage and time effects on the formation of hydroxyapatite-containing titania prepared by plasma electrolytic oxidation on Ti-6Al-4V alloy and its corrosion behavior

Producing titania and hydroxyapatite (HA) bioceramic coating on titanium alloys increases corrosion resistance and biocompatibility of these alloys. Plasma electrolytic oxidation (PEO) is one of the effective techniques for producing this type of coating. This method produces coatings with enough thickness and appropriate adhesion. In this study, titania and HA were directly produced on Ti-6Al-4V by applying PEO process in a Ca- and P-containing electrolyte by changing voltage and time parameters. Morphology and cross section, chemical composition and elements of coatings were investigated by scanning electron microscope, X-ray diffraction and energy dispersive spectroscopy, respectively. Corrosion behavior of the samples was also examined by potentiodynamic polarization and electrochemical impedance spectroscopy. The results indicated that the formation of HA phase with titania needs a minimum voltage below which HA is not formed. By increasing the operation time, the amount of the formed HA increased. Also, the sample coated at 500 V and 15 min showed the best corrosion behavior in Ringer's solution.     

Effect of welding speed on butt joint quality of Ti–6Al–4V alloy welded using a high-power Nd:YAG laser

Annealed Ti–6Al–4V alloy sheets with 1 and 2 mm thickness are welded using a 4 kW Nd:YAG laser system. The effects of welding speed on surface morphology and shape, welding defects, microstructure, hardness and tensile properties are investigated. Weld joints without or with minor cracks, porosity and shape defects were obtained indicating that high-power Nd:YAG laser welding is a suitable method for Ti–6Al–4V alloy. The fusion zone consists mainly of acicular α′ martensite leading to an increase of approximately 20% in hardness compared with that in the base metal. The heat-affected zone consists of a mixture of α′ martensite and primary α phases. Significant gradients of microstructures and hardness are obtained over the narrow heat-affected zone. The laser welded joints have similar or slightly higher joint strength but there is a significant decrease in ductility. The loss of ductility is related to the presence of micropores and aluminum oxide inclusions.     

Effects of different binders on microstructure and phase composition of hydroxyapatite Nd-YAG laser clad coatings

The laser clad coating technique can help to produce metallurgical bonding with high bonding strength between the coating layer and the substrate, which has been gradually applied for hydroxyapatite (HA) coating on metallic substrates. In this study, HA powder is mixed with two different binders, namely water glass (WG) and polyvinyl alcohol (PVA), respectively, and is then clad on Ti-6Al-4V substrates using an Nd:YAG laser system under various processing conditions. The microstructure, chemical composition and hardness of the coating layer and transition layer of the various samples are then systematically explored. The experimental results show that the coating layers of the various samples all contain both cellular dendrites and rod-like piled structures, while the transition layers contain only cellular dendrites. For all samples, the coating layer consists mostly of CaTiO₃, Ca₂P₂O₇, CaO and HA phases, whereas the transition layer contains primarily CaTiO₃, Ca₂P₂O₇, Ti₃P, Ti and HA phases. In addition, the transition layer of the WG samples also contains SiO₂ and Si₂Ti phases. In all of the specimens, the transition layer has a higher average hardness than the substrate or coating layer. Moreover, the transition layer in the WG sample is harder than that in the PVA sample.     

Spectroscopic characterization of low-nickel copper welding with pulsed Nd:YAG laser

Effects of various operating parameters of 400 W pulsed Nd:YAG laser on welding of nickel-alloyed copper have been investigated. The induced plume spectra in case of using different assist gases and preheat temperatures have been analyzed and the effects of these key factors on melt features such as penetration depth, porosity and spattering have been attributed to the spectroscopic behavior of the plume. Moreover, the CuI electron temperature and its standard deviation as the spectroscopic responses of the plasma plume to various laser process parameters have been quantitatively evaluated at different average and peak powers and pulse energies. Also, the mentioned responses were utilized to justify the weld bead profile features, involving weld depth, width and their stabilities, at similar process parameters. The operating conditions of welding were optimized, regarding the results of spectroscopic observations and attributing them to the qualitative aspects of the melt pool.     

Laser surface micro-texturing of Ti-6Al-4V substrates for improved cell integration

Biological behaviour of an implant, such as osseointegration, depends on both the chemical composition and the morphology of the surface of the implant. This paper reports the surface modification of Ti-6Al-4V - which is widely used in implantation - by Nd:YAG (λ = 1064 nm, τ = 100 ns) laser irradiation in order to enhance biointegration. Surface parameters are evaluated in terms contact angle measurement and surface roughness. Biocompatibility of the samples is investigated in vitro by monitoring 2T3 osteoblast cell growth on the samples through MTT assay.     

Experimental study of a high power and high efficiency CW diode-side-pumped Nd:YAG laser

This paper reports on the characterization of a diode-side-pumped CW Nd:YAG laser. A side-pumped configuration with 9 laser diodes is used for the laser. Pump light is directly coupled into the Nd:YAG rod without focusing lenses and the pump light distribution in the Nd:YAG rod was calculated. A maximum output power of 150 W in multimode operation is obtained for a pumping power of 400 W. The optical–optical efficiency is 37%. Output power of the laser under different output couplers, resonator lengths and temperatures of the cooling water have been studied.     

Characterization of Ti6Al4V implant surface treated by Nd:YAG laser and emery paper for orthopaedic applications

A more noble and biocompatible Ti alloy was achieved at fluence of 140 J cm⁻² where the implant indicated a higher degree of hardness (825HV), higher corrosion resistance (−0.21 V) and highest hydrophilicity (i.e. θ_c = 37°) compared with 70° of the control sample. These values corresponded to 58 and 39 mN m⁻¹ of surface tension respectively. The laser treated samples at 140 J cm⁻² showed higher wettability characteristics than mechanically roughened surface. Cell growth and their spreading condition in a specific area were analyzed by SEM and Image J Program software. Clearly, more cells were attached (1.2 × 10⁵) to and spread (488 μm²) over the surface at 140 J cm⁻² than in any other condition. Pathologically, the treated samples indicated no sign of infection.     

Infrared thermography for monitoring heat generation in a linear friction welding process of Ti6Al4V alloy

The increasing use of titanium alloys in a wider range of applications requires the development of new techniques and processes capable to decrease production costs and manufacturing times. In this regard welding and other joining techniques play an important role. Today, solid state friction joining processes, such as friction stir welding, friction spot welding, inertia friction welding, continuous-drive friction welding and linear friction welding (LFW), represent promising methods for part manufacturing. They allow for joining at temperature essentially below the melting point of the base materials being joined, without the addition of filler metal.However, the knowledge of temperature is essential to understand and model the phenomena involved in metal welding. A global measured value represents only a clue of the heat generation during the process; while, a deep understanding of welding thermal aspects requires temperature field measurement. This paper is focused on the use of infrared thermography applied to the linear friction welding process of Ti6Al4V alloy. The attention is concentrated on thermal field that develops on the outer wall of the two parts to be joined (i.e. heat generated in the friction zone), and on the maximum temperature that characterizes the process before and after the flash formation.     

Oscillation conditions of cw simultaneous dual-wavelength Nd：YAG laser for transitions 4F3／2-4I9／2 and 4F3／2-4I11／2

The operating condition of a cw simultaneous dual-wavelength Nd:YAG laser for both {}^4F_{3/2}-{}^4I_{9/2} (quasi-three-level system) and {}^4F_{3/2}-{}^4I_{11/2}(four-level system) transitions is studied. According to this condition, the cw simultaneous dual-wavelength at 1.06μm and 946 nm in Nd:YAG crystal has been realized experimentally through an adaptive coating design of the cavity mirrors. A total power output of 2.5W of the dual-wavelength at 946nm and 1.06μm has been achieved with an optical conversion efficiency 14.3%. The experimental results are in good agreement with the theoretical analysis.     

A new proposal of high repetitive Nd:YAG laser power supply adopted the sequential charge and discharge circuit

The pulsed Nd:YAG laser is the most commonly used type of solid-state laser in many fields. In material processing, the power density control of a laser beam has been considered to be significant, which depends on the flashlamp current pulse width and pulse repetition rate.In this study, we have proposed a new method of sequential charge and discharge circuit (SCADC) to control the laser power density. The power supply of SCADC is composed of low frequency capacitors instead of very expensive high frequency capacitors. We could find the stability of laser output as well as the flashlamp current up to the pulse repetition rate of 150 pps. As increasing a repetition rate from 30 to 150 pps by the step of 30 pps, it is known that the laser outputs increased by 10 W.