Tensile mechanical properties of basalt fiber reinforced polymer composite under varying strain rates and temperatures

High-strength woven fabrics and polymers are ideal materials for use in structural and aerospace systems. It is very important to characterize their mechanical properties under extreme conditions such as varying temperatures, impact and ballistic loadings. In this present work, the effects of strain rate and temperature on the tensile properties of basalt fiber reinforced polymer (BFRP) were investigated. These composites were fabricated using vacuum assisted resin infusion (VARI). Dynamic tensile tests of BFRP coupons were conducted at strain rates ranging from 19 to 133 s⁻¹ using a servo-hydraulic high-rate testing system. Additionally, effect of temperature ranging from −25 to 100 °C was studied at the strain rate of 19 s⁻¹. The failure behaviors of BFRP were recorded by a Phantom v7.3 high speed camera and analyzed using digital image correlation (DIC). The results showed that tensile strength, toughness and maximum strain increased 45.5%, 17.3% and 12.9%, respectively, as strain rate increased from 19 to 133 s⁻¹. Moreover, tensile strength was independent of varying temperature up to 50 °C but decreased at 100 °C, which may be caused by the softening of epoxy matrix and weakening of interfaces between fibers and matrix when the glass transition temperature was exceeded.     

A simple method of electrochemical lithium intercalation within graphite from a propylene carbonate-based solution

Electrochemical lithium intercalation within graphite from 1 mol dm^− 3 solution of LiClO₄ in propylene carbonate (PC) was investigated at 25 and − 15 °C. Lithium ions were intercalated into and de-intercalated from graphite reversibly at − 15 °C despite the use of pure PC as the solvent. However, ceaseless solvent decomposition and intense exfoliation of graphene layers occurred at 25 °C. The results of the Raman spectroscopic analysis indicated that the interaction between PC molecules and lithium ions became weaker at − 15 °C by chemical exchange effects, which suggested that the thermodynamic stability of the solvated lithium ions was an important factor that determined the formation of a solid electrolyte interface (SEI) in PC-based solutions. Charge–discharge analysis revealed that the nature of the SEI formed at − 15 °C in 1 mol dm^− 3 of LiClO₄ in PC was significantly different from that formed at 25 °C in 1 mol dm^− 3 of LiClO₄ in PC containing vinylene carbonate, 3.27 mol kg^− 1 of LiClO₄ in PC, and 1 mol dm^− 3 of LiClO₄ in ethylene carbonate.     

Experimental low temperature water content in gaseous methane,liquid ethane,and liquid propane in equilibrium with hydrate at cryogenic conditions

In low temperature gas processing, the presence of water can result in the formation of gas hydrate plugs. To avoid this problem, it is important to know the water solubility in natural gas components in equilibrium with gas hydrate. In this study experimental measurements of water content in gaseous methane in equilibrium with hydrate at 3.45 MPa (500 psia) and 6.90 MPa (1000 psia) and temperatures ranging from −3.2 °C (26.2 °F) to −80 °C (−112 °F) are presented. Similar measurements are presented for liquid ethane at 3.45 MPa (500 psia) and temperatures from −2.2 °C (28.0 °F) to −70 °C (−94 °F), and for liquid propane at 0.86 MPa (125 psia) and temperatures down to −60 °C (−76 °F), respectively.In measuring the water content, a Panametrics moisture sensor (calibrated to 1 ppb water content in nitrogen) has been used in flowing streams of the hydrocarbon-rich phases that are saturated with water. The results obtained with the Panametrics hygrometer show good agreement (normally better than ±4%) with previous measurements, which were obtained by a gas chromatographic technique for methane, ethane, and propane at temperatures ranging from −2.0 °C (28.4 °F) to −30 °C (−22 °F), which are within the hydrate region.     

Assessment of thermally aged XLPE insulation material under extreme operating temperatures

The degradation of cross-linked polyethylene (XLPE) insulation material is critical for the safe operation of cables. While there are extensive studies on the thermo-oxidative ageing of XLPE at or below 130 °C, the maximum overload conductor operating temperature, the short circuit temperature can rise above 150 °C, and the ageing patterns at these situations have not been fully understood. Here, chemical, crystalline structure, cross-linking density as well as the mechanical properties were characterized. The results demonstrate the importance of antioxidants in the high temperature situation. Before antioxidants are completely consumed, most of the mechanical and physicochemical properties remain stable. While antioxidant is depleted, the thermo-oxidative degradation is detrimental to the structure and properties of the insulation. The activation energy is around 160 kJ/mol for the thermo-oxidative ageing, from which the lifetime allowed before serious destruction of the insulation at different shortage or overload temperatures can be calculated.     

Tensile properties of semi-crystalline thermoplastic polymers: Effects of temperature and strain rates

This work deals with the study of temperature and time dependency of tensile properties of a PA 12-based polymer. The range of variation of parameters in experiments was linked to in-service conditions of components manufactured with this material (temperature interval from ?25 °C to 50 °C and average strain-rate magnitudes from 0.00028 s^?1 to 9.4 s^?1). For tests with different temperatures and low speed, an electro-mechanical machine, Zwick Z250, equipped with an incremental extensometer was used. To study the effect of strain rate at medium speeds, a servo-hydraulic system, Schenk PC63M, equipped with a strain-gauge extensometer was used, while at high speeds a servo-hydraulic machine, Instron VHS 160/20, equipped with a high-speed camera for strain evaluation by digital image correlation was employed. The changes of the rate of deformation with strain as well as elastic modulus variation with strain were studied. An increase in the elastic modulus and yield strength was observed with a drop in temperature and an increase in the strain-rate, temperature having a stronger influence on the variation of mechanical properties. The collected data was assembled in an elasto-plastic material model for finite-element simulations capable of rendering temperature- and strain-rate-dependency. The model was implemented in the commercial software Abaqus, yielding accurate results for all tests.     

Temperature and variable strain rate sensitivity in recycled HDPE

The recycling of post-consumer plastics and their utilization as raw materials to develop value-added products has become an important goal worldwide. The present work is concerned with the thermo-mechanical analysis of recycled high-density polyethylene (HDPE) under uniaxial tensile loading. The main focus is to propose a one-dimensional phenomenological model able to describe the influence of temperature and strain rate on the mechanical behavior. Tensile tests were performed over a wide range of temperatures (from 25°C to 100°C). Each experiment was performed under controlled strain rate varying from 7.25 × 10⁻⁵ s⁻¹ to 7.25 × 10⁻³ s⁻¹ in steps. It is shown that only one tensile test performed at three different temperatures is necessary to fully identify experimentally all material parameters that arise in the theory. Thus, with this experimental procedure, the number of tests used to evaluate the mechanical properties of recycled HDPE is significantly reduced. The experiments are compared with the model predictions and show good agreement.     

Kinetics of Lime Pretreatment of Sugarcane Bagasse to Enhance Enzymatic Hydrolysis

The objective of this work was to determine the optimum conditions of sugarcane bagasse pretreatment with lime to increase the enzymatic hydrolysis of the polysaccharide component and to study the delignification kinetics. The first stage was an evaluation of the influence of temperature, reaction time, and lime concentration in the pretreatment performance measured as glucose release after hydrolysis using a 2³ central composite design and response surface methodology. The maximum glucose yield was 228.45 mg/g raw biomass, corresponding to 409.9 mg/g raw biomass of total reducing sugars, with the pretreatment performed at 90°C, for 90 h, and with a lime loading of 0.4 g/g dry biomass. The enzymes loading was 5.0 FPU/dry pretreated biomass of cellulase and 1.0 CBU/dry pretreated biomass of β-glucosidase. Kinetic data of the pretreatment were evaluated at different temperatures (60°C, 70°C, 80°C, and 90°C), and a kinetic model for bagasse delignification with lime as a function of temperature was determined. Bagasse composition (cellulose, hemicellulose, and lignin) was measured, and the study has shown that 50% of the original material was solubilized, lignin and hemicellulose were selectively removed, but cellulose was not affected by lime pretreatment in mild temperatures (60–90°C). The delignification was highly dependent on temperature and duration of pretreatment.     

Measurement of coefficient of thermal expansion of films using digital image correlation method

Applications of the digital image correlation method (DIC) for the determination the coefficient of thermal expansion (CTE) of films is investigated in this paper. A heating chamber was designed for applying thermal load and DIC provides the full-field thermal deformation fields of the test film sample due to temperature changes. The average normal strains in the x and y direction from the region of interest are then extracted for the determination of CTE. The influence of unavoidable small rigid body rotation is discussed and a method to eliminate it to show the pure thermal expansion of the test film is demonstrated. For validation, the CTE of a pure copper sample is determined and compared with the textbook value, confirming the effectiveness and accuracy of the proposed technique. Finally, the CTE of Polyimide (PI) composite film in the temperature range of 20–140 °C is measured. The results reveal that the DIC is a practical and effective tool for full-field thermal deformation and CTE measurement of films.     

Thermal investigations associated with the behaviour patterns of resting workers of <Emphasis Type="Italic">Bombus atratus</Emphasis> (Hymenoptera: Apidae)

The Neotropical bumblebee Bombus (Fervidobombus) atratus Franklin is widely distributed in South America ranging from tropical and subtropical lowlands to high altitudes in the Andes. Thermal investigations of the Neotropical bumblebee Bombus atratus at rest were performed by means of thermometry. Most social insects are diurnal foragers. When they are inside their nests during the night, they carry out some tasks such as cleaning the nest, brood care or nest thermoregulation. However, forager bees generally pause at night in a sleep-like state. A bumblebee nest was transferred to a brood chamber which was maintained at approximately constant temperature (28 ± 1 °C) to prevent the workers from building the protecting involucrum so that one could mark them at birth. To provide a temperature gradient, two chambers were installed adjacent to the brood chamber, so that the workers had the chance to choose between 3 temperatures: the first one kept at 22 ± 1 °C, the second at 19 ± 1 °C and 28 ± 1 °C. The temperatures of the chambers were recorded continuously by a four channel data logger. Three categories of tasks performed by workers were registered in this investigation: warming brood (task 1), feeding brood (task 2) and foragers (task 3). During the experiment 357 workers were born and 252 (71%) of them showed sleep-like behaviour. The total sleep time in hours according to the work done by the workers was task 1 (240.6 h) > task 3 (236.0 h) > task 2 (227.3 h). The workers who performed tasks 1 and 2 preferred to sleep at the highest temperature (28 ± 1 °C) and the forager workers at 22 ± 1 °C.     

MIR imaging bundles of ordered silver halide polycrystalline fibres for thermal transmission and imaging

This study aims to experimentally examine the energy-saving potential by using R-134a filled separated two-phase thermosiphon loop (STPTL) for data center applications. A parametric study had been made to compare the energy consumption of two data center racks. Two fin-and-tube heat exchangers were attached to one of the racks to form two individual thermosiphon loops. The experiments were carried out subject to different operating conditions, including three ambient temperatures (20 °C, 23 °C, and 27 °C) and filling ratios ranging from 30 to 90% in association with heating loads ranging between 1.5 kW and 6 kW. Parametric influences regarding concentrated heat loading or uniform heat loading are studied. It was found that an appreciable energy-savings can be obtained at high filling ratios and a maximum of 49% energy-saving with the assistance of thermosiphon is observed. Accordingly, the rising of system pressure will result in noticeable savings. Relative to the uniform heat loading of the data rack, the thermosiphon shows even more energy-saving potential in concentrated heat loading. This phenomenon is more pronounced at a lower ambient temperature like 20 °C. On the other hand, there is no appreciable energy-saving for the thermosiphon between concentrated and uniform heating loads when the ambient temperature is high (27 °C). Furthermore, the influence of airflow rate was also investigated under various ambient temperatures with a 90% filling ratio and a heating load of 6 kW. The results revealed that the lower airflow rate in the thermosiphon yields comparatively better energy-saving than the higher flow rate. The study on the influence of using two STPTLs indicated that 15–23% energy-saving can be achieved at a 90% filling ratio and 6 kW heating load for all the studied ambient conditions if compared with testing each loop separately. Lower thermal resistance is seen at the higher filling ratios, ambient temperatures, and heating loads.

     

Controlled nanosheet morphology of titanium carbide Ti3C2Tx MXene via drying methods and its electrochemical analysis

Journal of Solid State Electrochemistry - The different temperature drying processes were carried out at −60&nbsp;°C, 15&nbsp;°C, and 60&nbsp;°C to control the...     

Synthesis and properties of poly(isosorbide 2,5-furandicarboxylate-co-ε-caprolactone) copolyesters

Bio-based poly(isosorbide 2,5-furandicarboxylate-co-ε-caprolactone) (PIFCL) copolyesters were synthesized from 2,5-furandicarboxylic acid, isosorbide and ε-caprolactone. The obtained copolyesters were characterized by ¹H NMR, ¹³C NMR, intrinsic viscosity, GPC, DSC, TGA and tensile testing. The NMR characterization results confirmed the insertion of lactones units into poly(isosorbide 2,5-furandicarboxylate) (PIF) chains. All PIFCL copolyesters were amorphous with T_{D, 5%} higher than 300 °C. The glass transition temperatures of PIFCLs with FDCA molar ratio from 74% to 45% were within the range of 132.1 °C and 72.4 °C. Tensile testing revealed that introduction of ε-caprolactone into PIF chain imparted PIFCL with excellent mechanical performance, typically, PIFCL polyseter with FDCA molar ratio of 45% had a Young's modulus 858 ± 92 MPa, a tensile strength 44 ± 4 MPa and an elongation at break 480 ± 45%.     

Effect of working temperature on the interfacial behavior of overmolded hybrid fiber reinforced polypropylene composites

In the present study, the interfacial behavior of overmolded hybrid fiber reinforced polypropylene composites (hybrid composites) in the working temperature range from 23 °C to 90 °C was studied by experimental and constitutive methods. Monotonic and cycle loading-unloading single-lap-shear tests were employed to determine the interfacial properties of hybrid composites. The experimental results show that both interfacial shear strength and shear stiffness decrease with increasing working temperature. A regression function was adopted to evaluate the decaying degree of interfacial properties with increasing working temperature. The shear stress-displacement relationship under monotonic loading exhibits nonlinear behavior after an initial elastic region. The envelope lines of shear stress-displacement of hybrid composites under cyclic loading indicate that the nonlinearity in the curve is caused by the plastic deformation of polypropylene in the interphase region. A constitutive model was built to describe the nonlinear shear stress-displacement relation of hybrid composites at different working temperatures. A full suite of temperature-dependent plastic parameters in the model was obtained from cyclic loading-unloading tensile tests. The predicted shear stress–displacement curves agreed well with experimental results from different working temperatures. In addition, the failure mode of hybrid composites varied with working temperature.     

The electrochemical properties of thermophilic cytochrome P450 CYP119A2 at extremely high temperatures in poly(ethylene oxide)

The electrochemical measurements were carried out by using thermophilic cytochrome P450 CYP119A2 (P450st) modified with poly(ethylene oxide) (PEO) in PEO₂₀₀ as an electrochemical solvent. The PEO modified P450st gave clear reduction–oxidation peaks by cyclic voltammetry in oxygen-free PEO₂₀₀ up to 120 °C. The midpoint potential measured for the P450st was −120 mV vs. [Fe(CN)₆]⁴⁻/[Fe(CN)₆]³⁻ at 120 °C. The peak separation, ΔE, was 16 mV at 100 mV/s. The estimated electron transfer rate of PEO-P450st at 120 °C was 35.1 s⁻¹. The faster electron transfer reaction was achieved at higher temperatures. The electrochemical reduction of dioxygen was observed at 115 °C with the PEO-modified P450st system.     

Coupled effect of ageing and temperature in the mechanical behaviour of a polyamide

The present work is concerned with the thermo-mechanical analysis of a particular aliphatic polyamide with long alkyl chains used in the internal sheath of flexible pipes. The main focus is to analyse the coupled influence of temperature and ageing on its mechanical behaviour and fracture. Fracture and tensile tests were performed over a wide range of temperature (from −5 °C to 90 °C) and of corrected inherent viscosity (between 1.0 dl/g and 1.8 dl/g). For higher values of the CIV, the material presents superplastic behaviour, but the behaviour tends to be brittle for lower values of the inherent viscosity and temperature. A general model is proposed for the uniaxial behaviour (valid for a wide range of temperature and inherent viscosity) and also for the fracture behaviour. Experiments are compared with the model predictions and show good agreement.     

Effect of cyclic loading on tensile properties of PC and PC/ABS

The effects of cyclic loading on tensile fracture properties of polycarbonate (PC) and the alloy of polycarbonate and acrylonitrile-butadiene-styrene (PC/ABS) are experimentally investigated in the paper. Two digital cameras are used to record simultaneously the tensile deformation of specimens and the large deformation and the necking process of these polymers are discussed. Two lateral contractions are not identical at the later tensile stages and the contraction ratios in each lateral direction are related with the tensile strains in axial direction on width and thickness surface. The curvature radiuses at the minimum section during necking process are shown. The volume increases during necking process and then decreases gradually. The yield stress and fracture stress of PC/ABS are lower than that of PC. The degradation of the fracture stress and fracture strain due to the application of cyclic loading is larger for PC than that for PC/ABS, and these can be used to explain qualitatively why PC has higher fatigue crack growth rate than PC/ABS.     

Tensile behavior of quasi-unidirectional glass fiber/polypropylene composites at room and elevated temperatures

In the present study, the tensile behavior of quasi-unidirectional glass fiber/polypropylene composites at room and elevated temperatures were investigated by both micro- and macromechanical test methods. In the micromechanical studies, a single fiber fragmentation test was employed for measuring the interfacial shear strength at fiber-polypropylene interface in the temperature range from 23 °C to 90 °C. The results show that interfacial shear strength decreases with increasing testing temperature. In the macromechanical studies, experimental results show that the elastic modulus of polypropylene and transverse elastic modulus of composites are sensitive to the testing temperature. The weakened fiber-polypropylene interface due to elevated temperatures led to the vanishing of “knee” in transverse tensile stress-strain curves. A function was proposed to evaluate the dependence of the elastic modulus of quasi-unidirectional glass fiber/polypropylene composites on the testing temperatures and tested against experimental data. Tensile failure mechanisms of composites were demonstrated to evolve with the testing temperature.     

Surface structures and electrochemical characteristics of surface-modified carbon anodes for lithium ion battery

Petroleum coke and those heat-treated at 1860 °C, 2100 °C, 2300 °C 2600 °C and 2800 °C (abbreviated as PC, PC1860, PC2100, PC2300, PC2600 and PC2800) were fluorinated by elemental fluorine of 3 × 10⁴ Pa at 200 °C and 300 °C for 2 min. Natural graphite powder samples with average particle sizes of 5 μm, 10 μm and 15 μm (abbreviated as NG5μm, NG10μm and NG15μm) were also fluorinated by ClF₃ of 3 × 10⁴ Pa at 200 °C and 300 °C for 2 min. Transmission electron microscopic (TEM) observation revealed that closed edge of PC2800 was destroyed and opened by surface fluorination, which increased the first coulombic efficiencies of PC2300, PC2600 and PC2800 by 12.1–18.2% at 60 mA/g and by 13.3–25.8% at 150 mA/g in 1 mol/dm³ LiClO₄–ethylene carbonate (EC)/diethyl carbonate (DEC) (1:1 in volume). Light fluorination of NG10μm and NG15μm increased the first coulombic efficiencies by 22.1–28.4% at 150 mA/g in 1 mol/dm³ LiClO₄–EC/DEC/PC (PC: propylene carbonate, 1:1:1 in volume).