Efficiency of succinylated-olive stone biosorbent on the removal of cadmium ions from aqueous solutions

Chemical functionalization of olive stone wastes with succinate linkers can potentially improve the performance of wastewater treatment technologies via enhanced adsorption and high affinity of the covalently attached succinate groups for heavy metals. In this study, a novel reusable adsorbent material based on agricultural waste has been synthesized by esterifying the lignocellulosic matrix of olive stones with succinic anhydride in toluene under basic conditions. Characterization of the as-prepared material by FTIR and solid-state MAS ¹³C NMR spectroscopies and TGA confirmed that the heterogeneous esterification has proceeded very efficiently to yield the succinylated-olive stone (S–OS). Subsequent alkaline treatment of S–OS with saturated NaHCO₃ aqueous solution led to the resulting sodic material (NaS–OS), which was subjected to batch experiments in order to evaluate its cadmium-removing efficiency from aqueous solutions at realistic concentrations of cadmium found in industrial effluents. The results obtained from the sorption characteristics have revealed that NaS–OS material is highly effective in removing cadmium from aqueous solutions, with a maximum uptake capacity of 200 mg g⁻¹ (1.78 mmol g⁻¹). The Langmuir isotherm model was found to fit adequately the equilibrium isotherm data. Cadmium adsorption occurs rapidly and the adsorption mechanism is a chemical sorption via ionic exchange between the adsorbate and adsorbent. Thermodynamic parameters were also evaluated from the effect of temperature studies. Regenerability of NaS–OS material was ascertained by quantitative desorption of cadmium with 1 M aqueous NaCl and the reusability of the matrix after five repeated cycles led to nearly no attenuation in its performance (less than 2% in the sorption capacity), indicating that repeated use of NaS–OS is quite feasible. Compared to other low-cost adsorbents utilized for the removal of Cd(II) from water/wastewater, NaS–OS shows higher sorption capacity. These results have important implications for the design of low-cost adsorbents based on agricultural wastes.     

Effective removal of 4-Aminophenol from aqueous environment by pea (Pisum sativum) shells activated with sulfuric acid: Characterization,isotherm, kinetics and thermodynamics

The threat of phenol contamination in aquatic ecosystems is significant for the health of the earth's water systems as well as all humans on it. The present study was conducted to synthesize a cost-effective adsorbent (pea shells activated with sulfuric acid, PSASA) from agriculture waste (pea shells) and its use for effective removal of toxic 4-Aminophenol (4-AP). Newly designed PSASA exhibited significant adsorption of 4-AP which was confirmed by SEM, FT-IR, and XRD analysis. Surface topography confirmed high unevenness of the PSASA surface and the macroporous feature of the PSASA was confirmed by BET analysis. . Multiple testing was done to see how various factors affected adsorption such as adsorbent dose, temperature, pH, PZC, the effect of KCl and urea addition and the effect of the initial concentration of 4-AP. A drop in adsorption uptake of 4-AP was observed as the temperature increases from 25 °C to 45 °C. Maximum adsorption uptake (q_m) was found to be 106.11 mg/g at an optimum pH of 7.0 and 25 °C. Among various adsorption isotherm models tested, Langmuir Isotherm gave the best explanation with high R² values of experimental data. The pseudo-first-order model was found to explain the kinetics of adsorption well. The thermodynamic finding confirms the adsorption process was physical and exothermic. The adsorption of 4-AP was primarily governed by electrostatic interaction, hydrogen-bonding and π-π exchange mechanism. Because of the positive outcomes of the present research, we can use the PSASA as a cost-effective adsorbent for removing phenolic compounds.     

Rapid removal of anionic organic dye from contaminated water using a poly(3-aminobenzoic acid/graphene oxide/cobalt ferrite) nanocomposite low-cost adsorbent via adsorption techniques

This research study aims to remove hazardous anionic azo dyes (Congo red (CR)) from aqueous solutions via a simple adsorption method using a poly(3-aminobenzoic acid/graphene oxide/cobalt ferrite) nanocomposite (P3ABA/GO/CoFe₂O₄) as a novel and low-cost nanoadsorbent, as synthesized by a simple and straightforward polymerization method. Typically, 3-aminobenzoic acid (3ABA), as monomer, was chemically polymerized with graphene oxide (GO) and cobalt ferrite (CoFe₂O₄) in an aqueous acidic medium containing an ammonium persulfate initiator. The adsorbent P3ABA/GO/CoFe₂O₄ nanocomposite was characterized using various techniques such as Fourier transform infrared spectroscopy, X-ray diffraction, thermogravimetric analysis, transmission electron microscopy, scanning electron microscopy, energy-dispersive analysis by X-ray and Brunauer–Emmett–Teller, vibrating sample magnetometer, and zeta potential techniques. These techniques confirmed the interaction between the poly(3-aminobenzoic acid) with GO and CoFe₂O₄ due to the presence of π-π interactions, hydrogen bonding, and electrostatic forces. Herein, the removal efficiency of dye from aqueous solution by the adsorbent was studied according to several parameters such as the pH of the solution, dye concentration, dosage of adsorbent, contact time, and temperature. The adsorption of the dye was fitted using a Langmuir model (R² between 0.9980 and 0.9995) at different temperatures, and a kinetic model that was pseudo-second order (R² = between 0.9993 and 0.9929) at various initial concentrations of CR dye. In addition, the data revealed that the P3ABA/GO/CoFe₂O₄ nanocomposite exhibited a high adsorption capacity (153.92 mg/g) and removal for CR dye (98 %) at pH 5. Thermodynamic results showed the adsorption process was an endothermic and spontaneous reaction. It was found that, in terms of reusability, the P3ABA/GO/CoFe₂O₄ adsorbent can be used for up to six cycles. In this study, P3ABA/GO/CoFe₂O₄ nanocomposites were found to be low cost, and have an excellent removal capability and fast adsorption rate for CR from wastewater via a simple adsorption method. Moreover, this adsorbent nanocomposite could be simply separated from the resultant solution and recycled.     

Adsorption of cesium on domestic bentonites

Bentonite is a natural clay and one of the most promising candidates for use as a buffer material in the geological disposal systems for spent nuclear fuel and high-level nuclear waste. It is intended to isolate metal canisters with highly radioactive waste products from the surrounding rocks because of its ability to retard the movement of radionuclides by adsorption. Slovak Republic avails of many significant deposits of bentonites. Adsorption of Cs on five Slovak bentonites of deposits (Jelšovy potok, Kopernica, Lieskovec, Lastovce and Dolná Ves) has been studied with the use of batch technique. In the case of Dolná Ves deposit, the mixed-layer illite–smectite has been identified as the main clay component. Natural and irradiated samples, in two different kinds of grain size: 45 and 250 μm have been used in the experiments. The adsorptions of Cs on bentonite under various experimental conditions, such as contact time, adsorbent and adsorbate concentrations have been studied. The Cation Exchange Capacity values for particular deposits drop in the following order: Jelšovy potok > Kopernica > Lieskovec > Lastovce > Dolná Ves. Bentonites irradiated samples with 390 kGy have shown higher specific surface and higher values of the adsorption capacity. Distribution coefficients have been determined for bentonite-cesium solution system as a function of contact time and adsorbate and adsorbent concentration. The data have been interpreted in terms of Langmuir isotherm. The uptake of Cs has been rapid and the adsorption of cesium has increased with increasing metal concentrations. The adsorption percentage has decreased with increasing of metal concentrations. Adsorption of Cs has been suppressed by presence of Ca²⁺ more than Na⁺ cation. Sorption experiments carried out show that the most suitable materials intended for use as barriers surrounding a canister of spent nuclear fuel are bentonites of the Jelšovy potok and Kopernica deposits.     

Single-Step Hydrothermal Synthesis of Biochar from H3PO4-Activated Lettuce Waste for Efficient Adsorption of Cd(II) in Aqueous Solution

Developing an ideal and cheap adsorbent for adsorbing heavy metals from aqueous solution has been urgently need. In this study, a novel, effective and low-cost method was developed to prepare the biochar from lettuce waste with H₃PO₄ as an acidic activation agent at a low-temperature (circa 200 °C) hydrothermal carbonization process. A batch adsorption experiment demonstrated that the biochar reaches the adsorption equilibrium within 30 min, and the optimal adsorption capacity of Cd(II) is 195.8 mg∙g⁻¹ at solution pH 6.0, which is significantly improved from circa 20.5 mg∙g⁻¹ of the original biochar without activator. The fitting results of the prepared biochar adsorption data conform to the pseudo-second-order kinetic model (PSO) and the Sips isotherm model, and the Cd(II) adsorption is a spontaneous and exothermic process. The hypothetical adsorption mechanism is mainly composed of ion exchange, electrostatic attraction, and surface complexation. This work offers a novel and low-temperature strategy to produce cheap and promising carbon-based adsorbents from organic vegetation wastes for removing heavy metals in aquatic environment efficiently.     

Adsorption of La(III) onto GMZ bentonite: effect of contact time,bentonite content,pH value and ionic strength

Bentonite has been studied extensively because of its strong adsorption capacity. A local Na-bentonite named GMZ bentonite, collected from Gaomiaozi County (Inner Mongolia, China), was selected as the first choice of buffer/backfill material for the high-level radioactive waste repository in China. In this research, the adsorption of La (ΙΙΙ) onto GMZ bentonite was performed as a function of contact time, pH, solid content and metal ion concentrations by using the batch experiments. The results indicate that the adsorption of La (III) on GMZ bentonite achieves equilibration quickly and the kinetic adsorption follows the pseudo-second-order model; the adsorption of La (III) on the adsorbent is strongly dependent on pH and solid content, the adsorption process follows Langmuir isotherm. The equilibrium batch experiment data demonstrate that GMZ bentonite is effective adsorbent for the removal of La (III) from aqueous solution with the maximum adsorption capacity of 26.8 mg g⁻¹ under the given experimental conditions.     

Facile synthesis of mesoporous magnesium oxide–graphene oxide composite for efficient and highly selective adsorption of hazardous anionic dyes

Mesoporous magnesium oxide–graphene oxide composite (MGC) has been synthesized using a facile post-immobilization method by mixing pre-synthesized magnesium oxide (MgO) with graphene oxide (GO). MgO used for fabrication of the composite has been synthesized using an environment-friendly method involving gelatin as a template. XRD, Raman and EDX analyses have confirmed the presence of MgO and GO in the composite. FTIR and SEM analyses of synthesized MGC have further elucidated the surface functionalities and morphology, respectively. Using N₂ adsorption–desorption isotherm, BET surface area of MGC has been calculated to be 55.9 m² g^?1 and BJH analysis confirmed the mesoporous nature of MGC. The application of synthesized MGC as a selective adsorbent for various toxic anionic dyes has been explored. Batch adsorption studies have been carried out to investigate the influence of different adsorption parameters on the adsorption of two anionic dyes: indigo carmine (IC) and orange G (OG). The maximum adsorption capacities exhibited by MGC for IC and OG are 252.4 and 24.5 mg g^?1, respectively. Plausible mechanism of dye adsorption has been explained in detail using FTIR analysis. In a mixture of cationic and anionic dyes, MGC selectively adsorbs anionic dyes with high separation factors, while in binary mixtures of anionic dyes, both dyes are adsorbed efficiently. Thus, MGC has been shown to be a potential adsorbent for the selective removal of anionic dyes from wastewater.

     

Nitrate removal from aqueous solution using watermelon rind derived biochar-supported ZrO2 nanomaterial: Synthesis,characterization, and mechanism

Recently, biochar has attracted tremendous research interest for environmental applications. In this study, biochar-derived watermelon rind (WM) was produced via optimal pyrolysis at 500 °C for 2 h, and then improved the adsorption capacity by Zirconium oxide nanoparticles (ZrO₂ NPs). The WM@ZrO₂ was characterized using X-ray diffraction (XRD), Scanning electron microscopic - Energy-dispersive X-ray spectroscopy (SEM-EDS), and Fourier transform infrared (FTIR). The adsorptive capacities of synthesized ZrO₂ NPs were investigated for nitrate as a function of pH, adsorbent dosage, contact time, initial adsorbate concentration, and pyrolysis temperature in the batch experiment. The results showed that a Langmuir isotherm and a pseudo-second-order kinetics model were the best-fit for experimental nitrate data in its non-linear form as correlation coefficients (R²) were 0.985 and 0.998, respectively. The maximum adsorption capacity for the Langmuir isotherm model was 15.196 mg g^?1. The proposed mechanism, including electrostatic attraction and ligand exchange, played a dominant role in nitrate adsorption. After testing with the real domestic wastewater, the removal of nitrate for WM@ZrO₂ was achieved at 78 %, which was equivalent to the adsorption capacity of 8.1 mg g^?1 of adsorbent. Overall, the WM@ZrO₂ is proposed as a promising, effective, and environmentally friendly adsorbent in removing nitrate from an aqueous solution.     

Preconcentration of trace nickel lons from aqueous solutions by using a new and low cost chelating polystyrene adsorbent

A simple and reliable method has been developed using chelating polymeric adsorbent (PSAHSB) to preconcentration of trace amount of Ni(II) ions from aqueous solutions under static loading conditions, and their determination by Ultraviolet and visible (UV–Vis) absorption spectroscopy. The influences of some analytical adsorption parameters, such as pH, temperature and contact time, the ionization constants of chelating groups in the adsorbent and desorption process were investigated. Maximum adsorption ≥98% was achieved at pH 3–7 after 20 min of contact time and the relative standard-deviation values were ≤5%. Adsorbed metal ions have been desorbed with 10 mL of 2 M HCl acid with the detection limit of 0.0157 μg m⁻¹. The Langmuir and Freundlich isotherm equations were used to describe adsorption behavior of the system at different temperatures. Kinetic and thermodynamic behavior of the adsorbent for Ni(II) ion preconcentration was also studied. The possible adsorption mechanism of Ni (II) ions onto modified adsorbent is also discussed. This method was applied efficiently to remove Ni (II) ions from environmental water samples.     

Optimization of cadmium adsorption from aqueous solutions by functionalized graphene and the reversible magnetic recovery of the adsorbent using response surface methodology

Novel functionalized graphene adsorbent was prepared and characterized using different techniques. The prepared adsorbent was applied for the removal of cadmium ions from aqueous solution. A response surface methodology was used to evaluate the simple and combined effects of the various parameters, including adsorbent dosage, pH, and initial concentration. Under the optimal conditions, the cadmium removal performance of 70% was achieved. A good agreement between experimental and predicted data in this study was observed. The experimental results revealed of cadmium adsorption with high linearity follow Langmuir isotherm model with maximum adsorption capacity of 502 mg g^?1, and the adsorption data fitted well into pseudo‐second order model. Thermodynamic studies showed that adsorption process has exothermic and spontaneous nature. The recommended optimum conditions are: cadmium concentration of 970 mg L^?1, adsorbent dosage of 1 g L^?1, pH of 6.18, and T = 25 °C. The magnetic recovery of the adsorbent was performed using a magnetic surfactant to form a noncovalent magnetic functionalized graphene. After magnetic recovery of the adsorbent both components (adsorbent and magnetic surfactant) were recycled by tuning the surface charges through changing the pH of the solution. Desorption behavior studied using HNO₃ solution indicated that the adsorbent had the potential for reusability.     

Removal of 226Ra from aqueous media and its thermodynamics and kinetics

The composite adsorbent prepared by mixing of polyacrylonitrile and clinoptilolite was used for investigating the adsorption behaviour of ²²⁶Ra in column system. The effective parameters like initial activity concentration, pH of the solution, contact time and temperature for adsorption behaviour of ²²⁶Ra were studied. Adsorption efficiency of ²²⁶Ra on composite adsorbent from aqueous solution was determined to 98.73 ± 0.59 % at pH 5.0 and 30 °C in a short time. The isotherm models were studied to evaluated adsorption characteristics of ²²⁶Ra onto composite adsorbent. The thermodynamic parameters were showing that the processes for ²²⁶Ra were exothermic. Adsorption kinetics of the radium is also studied.

     

Separation of no-carrier-added <Superscript>107,109</Superscript>Cd from proton induced silver target: classical chemistry still relevant

The classical chemistry like precipitation technique is relevant even in modern days trans-disciplinary research from the view point of green chemistry. A definite demand of no-carrier-added (nca) cadmium tracers, namely, ^107,109Cd, has been realized for diverse applications. Development of efficient separation technique is therefore important to address the purity of the tracers for various applications. No-carrier-added ^107,109Cd radionuclides were produced by bombarding natural silver target matrix with 13 MeV protons, which gave ~15 MBq/μA h yield for nca ¹⁰⁷Cd. The nca cadmium radionuclides were separated from the natural silver target matrix by precipitating Ag as AgCl. The developed method is an example wherein green chemistry is used in trans-disciplinary research. The method is also simple, fast, cost effective and environmentally benign.     

Synthesis of PS/RB-Cs and its use in the treatment of water polluted with heavy metals

Polystyrene waste are non-biodegradable materials that causes harm to the environment. Red brick waste resulting from demolition and reconstruction are an obstacle to its disposal. To solve this problem and meet modern sustainability standards, this study utilized polystyrene (PS) foam and red brick construction waste to prepare composite materials (PS/RB-Cs) as a new efficient adsorbent. The PS/RB-Cs composite as an adsorbent was characterized using a UV–Vis Spectrophotometer, Energy Dispersive X-ray Spectroscopy (EDX), Scanning Electron Microscope (SEM), and transmission electron microscopy (TEM), which showed a clear spectrum shift after using PS/RB-Cs as an adsorbent. The PS/RB-Cs was characterized by a porous structure with higher surface area and high stability. The efficiency of the PS/RB-Cs in treating water contaminated with heavy metals such as cobalt and nickel was verified under different initial concentrations, temperatures, doses, pH, and contact times. The experimental q_e values were consistent with the q_e calculated values and were approximately 8 mg/g. The adsorption isotherm models showed that the adsorption results fit the Langmuir, Freundlich and Flory-Huggins isotherm models and that the process was favorable. By applying pseudo-first-order (PFO) and pseudo-second-order (PSO) kinetic models, the adsorption process was found to follow PSO. The findings of this research validated that the composite material that was prepared serves as a potent adsorbent for the treatment of water that has been polluted by heavy metals.     

Laterite clay-based geopolymer as a potential adsorbent for the heavy metals removal from aqueous solutions

This study is focused on the investigation of low iron lateritic clay-based geopolymer as a potential adsorbent for the higher uptake of Ni(II) and Co(II) ions from aqueous solutions. BET analysis revealed that the sieved geopolymer sample (SGS) was characterized by 17.441 m²/g of surface area, 0.005 cm³/g of pore volume, and 13.549 Å of pore diameter. SEM investigation confirmed the presence of pores and cavities onto the surface of SGS. XRD analysis showed that the geopolymer is semi-crystalline in nature. It was found that the adsorption ability of SGS remained 520 mg/g for Ni(II) ions and 500 mg/g for Co(II) ions when 0.5 M solutions were stirred with SGS for 60 min. The temperature and pH of the solution were maintained at 60 °C and 7.0, respectively. The adsorption data of both heavy metal (HM) ions fitted best in the pseudo-second-order kinetic model. The low activation energy value i.e. 2.507 kJ/mol for Ni(II) ions and 2.286 kJ/mol for Co(II) ions confirmed adsorption is physisorption. Adsorption data were tested with Langmuir and Freundlich models, the data showed comparatively better fitting in the Freundlich model. The greater value of monolayer adsorption capacity (Xm) for Ni(II) ions was found 1.77 × 10⁻² mol/g while for Co(II) ions it remained 1.69 × 10⁻² mol/g confirming the better interaction of metal ions with the adsorbent surface. Negative values of ΔG° confirmed the spontaneity of the process while the positive value of ΔS° showed the randomness of adsorbate particles. The positive value of ΔH° showed that the adsorption process remained endothermic for both HM ions. The experimental results confirmed the ability of laterite clay-based geopolymer for better removal of HM ions and hence can be employed for the wastewater treatment processes at low-cost adsorbent.     

Adsorption of <Superscript>85</Superscript>Kr radioactive inert gas into hardening mixtures

Changes in volumetric activity of ⁸⁵Kr radioactive inert gas take place in the atmosphere: it has increased by around 50% during the past 15 years. The main source of such gas is the operation of nuclear power plants and spent nuclear fuel reprocessing plants. ⁸⁵Kr as an inert gas spreads throughout the entire atmosphere and its ionizing radiation may result in changes of atmospheric electric phenomena. Therefore it is necessary to control ⁸⁵Kr emission into the atmosphere. However, there is no effective method for this as inert gases, under normal conditions, can hardly be adsorbed in different adsorbents and stored in special containers for a long period of time. This paper tries to show the possibility of keeping ⁸⁵Kr longer within the adsorbent by changing its aggregate state: gas is adsorbed into liquid adsorbent and desorption takes place from solid adsorbent. For this purpose, an epoxy resin is used which, after adding a special hardener at room temperature, turns into a solid material with density of around 1.2 × 10³ kg m⁻³. As a result of sample blending with substances which contribute to better solubility of ⁸⁵Kr, diffusion coefficient of this gas (i.e. desorption speed) changes within the adsorbent in the solid state.     

Optimizing adsorptive removal of malachite green and methyl orange dyes from simulated wastewater by Mn‐doped CuO‐Nanoparticles loaded on activated carbon using CCD‐RSM: Mechanism,regeneration, isotherm,kinetic, and thermodynamic studies

In the present work, Mn‐doped CuO‐NPs‐AC was prepared by a simple method, characterized using various techniques such as FESEM, EDX, XRD, PSD, and pH_pzc and finally used for the adsorption of malachite green (MG) and methyl orange (MO) in a number of single and binary solutions. A series of adsorption experiments were conducted to investigate and optimize the influence of various factors (such as different pH, concentration of MG and MO, adsorbent mass, and sonication time) on the simultaneous adsorption of MG and MO using response surface methodology. Under optimal conditions of pH 10, adsorbent dose of 0.02 g, MG concentration of 30 mg L^?1, MO concentration of 30 mg L^?1, and sonication time of 4.5 min at room temperature, the maximum predicted adsorption was observed to be 100.0%, for both MG and MO, showing that there is a favorable harmony between the experimental data and model predictions. The adsorption isotherm of MO and MG by Mn‐doped CuO‐NPs‐AC could be well clarified by the Langmuir model with maximum adsorption capacity of 320.69 mg g^?1 and 290.11 mg g^?1 in the single solution and 233.02 mg g^?1 and 205.53 mg g^?1 in the binary solution by 0.005 g of adsorbent mass for MG and MO, respectively. Kinetic studies also revealed that both MG and MO adsorption were better defined by the pseudo‐second order model for both solutions. In addition, the thermodynamic constant studies disclosed that the adsorption of MG and MO was likely to be influenced by a physisorption mechanism. Eventually, the reusability of the Mn‐doped CuO‐NPs‐AC after six times showed a reduction in the adsorption percentage of MG and MO.     

Synthesis and performance evaluation of chitosan/zinc oxide nanocomposite as a highly efficient adsorbent in the removal of reactive red 198 from water

In this study, Chitosan and Chitosan-zinc oxide (ZnO) nanocomposite were prepared and applied as a low-cost adsorbent with high adsorption capacity for removing reactive red 198 (RR 198) dye from contaminated water. After preparation, it was characterized using FT-IR, XRD, and SEM. The effect of pH, temperature, time, adsorbent amount, and initial dye concentration were investigated in the removal efficiency of RR 198. The maximum adsorption capacity (q_m) obtained from the Langmuir equation was 172.41 mg/g in adsorbent dose of 0.1 g/L, pH: 4, temperature of 25°C, adsorption time of 40 min. The thermodynamic parameters demonstrated the spontaneous and endothermic nature of the adsorption process. Due to the high efficiency of chitosan/ZnO nanocomposite in removal of RR 198 from water and advantages such as high adsorption capacity, simple synthesis, and easy application, it can be used as an effective method in the removal of RR 198 from water.     

Facial Synthesis of Adsorbent from Hemicelluloses for Cr(VI) Adsorption

It is challenging work to develop a low-cost, efficient, and environmentally friendly Cr(VI) adsorbent for waste water treatment. In this paper, we used hemicelluloses from chemical fiber factory waste as the raw material, and prepared two kinds of carbon materials by the green hydrothermal method as adsorbent for Cr(VI). The results showed that hemicelluloses hydrothermally treated with citric acid (HTC) presented spherical shapes, and hemicelluloses hydrothermally treated with ammonia solution (HTC-NH₂) provided spongy structures. The adsorption capacity of the samples can be obtained by the Langmuir model, and the adsorption kinetics could be described by the pseudo-second-order model at pH 1.0. The maximum adsorption capacity of HTC-NH₂ in the Langmuir model is 74.60 mg/g, much higher than that of HTC (61.25 mg/g). The green hydrothermal treatment of biomass with ammonia solution will provide a simple and feasible way to prepare adsorbent for Cr(VI) in waste water treatment.     

Dye and its removal from aqueous solution by adsorption: A review

In this review article the authors presented up to-date development on the application of adsorption in the removal of dyes from aqueous solution. This review article provides extensive literature information about dyes, its classification and toxicity, various treatment methods, and dye adsorption characteristics by various adsorbents. One of the objectives of this review article is to organise the scattered available information on various aspects on a wide range of potentially effective adsorbents in the removal of dyes. Therefore, an extensive list of various adsorbents such as natural materials, waste materials from industry, agricultural by-products, and biomass based activated carbon in the removal of various dyes has been compiled here. Dye bearing waste treatment by adsorption using low cost alternative adsorbent is a demanding area as it has double benefits i.e. water treatment and waste management. Further, activated carbon from biomass has the advantage of offering an effected low cost replacement for non-renewable coal based granular activated carbon provided that they have similar or better adsorption on efficiency. The effectiveness of various adsorbents under different physico-chemical process parameters and their comparative adsorption capacity towards dye adsorption has also been presented. This review paper also includes the affective adsorption factors of dye such as solution pH, initial dye concentration, adsorbent dosage, and temperature. The applicability of various adsorption kinetic models and isotherm models for dye removal by wide range of adsorbents is also reported here. Conclusions have been drawn from the literature reviewed and few suggestions for future research are proposed.     

Enhanced binding capacity of boronate affinity adsorbent via surface modification of silica by combination of atom transfer radical polymerization and chain-end functionalization for high-efficiency enrichment of cis-diol molecules

Boronate affinity materials have been widely used for specific separation and preconcentration of cis-diol molecules, but most do not have sufficient capacity due to limited binding sites on the material surface. In this work, we prepared a phenylboronic acid-functionalized adsorbent with a high binding capacity via the combination of surface-initiated atom transfer radical polymerization (SI-ATRP) and chain-end functionalization. With this method, the terminal chlorides of the polymer chains were used fully, and the proposed adsorbent contains dense boronic acid polymers chain with boronic acid on the chain end. Consequently, the proposed adsorbent possesses excellent selectivity and a high binding capacity of 513.6 μmol g⁻¹ for catechol and 736.8 μmol g⁻¹ for fructose, which are much higher than those of other reported adsorbents. The dispersed solid-phase extraction (dSPE) based on the prepared adsorbent was used for extraction of three cis-diol drugs (i.e., epinephrine, isoprenaline and caffeic acid isopropyl ester) from plasma; the eluates were analyzed by HPLC-UV. The reduced amount of adsorbent (i.e., 2.0 mg) could still eliminate interferences efficiently and yielded a recovery range of 85.6–101.1% with relative standard deviations ranging from 2.5 to 9.7% (n = 5). The results indicated that the proposed strategy could serve as a promising alternative to increase the density of surface functional groups on the adsorbent; thus, the prepared adsorbent has the potential to effectively enrich cis-diol substances in real samples.