Effect of Mg doping on morphology,photocatalytic activity and related biological properties of Zn1−xMgxO nanoparticles

The objective of this study is to synthesize ZnO and Mg doped ZnO (Zn_1−xMg_xO) nanoparticles via the sol-gel method, and characterize their structures and to investigate their biological properties such as antibacterial activity and hemolytic potential.Nanoparticles (NPs) were synthesized by the sol-gel method using zinc acetate dihydrate (Zn(CH₃COO)₂.2H₂O) and magnesium acetate tetrahydrate (Mg(CH₃COO)₂.4H₂O) as precursors. Methanol and monoethanolamine were used as solvent and sol stabilizer, respectively. Structural and morphological characterizations of Zn_1−xMg_xO nanoparticles were studied by using XRD and SEM-EDX, respectively. Photocatalytic activities of ZnO and selected Mg-doped ZnO (Zn_1−xMg_xO) nanoparticles were investigated by degradation of methylene blue (MeB). Results indicated that Mg doping (both 10% and 30%) to the ZnO nanoparticles enhanced the photocatalytic activity and a little amount of Zn0.90 Mg0.10 O photocatalyst (1.0 mg/mL) degraded MeB with 99% efficiency after 24 h of irradiation under ambient visible light. Antibacterial activity of nanoparticles versus Escherichia coli ( E. coli ) was determined by the standard plate count method. Hemolytic activities of the NPs were studied by hemolysis tests using human erythrocytes. XRD data proved that the average particle size of nanoparticles was around 30 nm. Moreover, the XRD results indicatedthat the patterns of Mg doped ZnO nanoparticles related to ZnO hexagonal wurtzite structure had no secondary phase for x ≤ 0.2 concentration. For 0 ≤ x ≤ 0.02, NPs showed a concentration dependent antibacterial activity against E. coli . While Zn_0.90Mg_0.10 O totally inhibited the growth of E. coli , upper and lower dopant concentrations did not show antibacterial activity.     

Modification in structural,optical, morphological,and electrical properties of zinc oxide (ZnO) nanoparticles (NPs) by metal (Ni,Co) dopants for electronic device applications

In the present work, Zinc Oxide (ZnO) nanoparticles (NPs) were synthesized by the chemical co-precipitation method using Zinc Chloride as the initial chemical, while Nickel and Cobalt chloride as dopants. Phase identification of metal (Ni, Co) doped Zinc Oxide nanoparticles (NPs) was observed using x-ray diffraction (XRD). The small lattice distortion or phase changes appeared due to shifting of diffraction angles peaks towards larger angle in ZnO are corresponded to metal (Ni, Co) dopant. The average crystallite size appears to decrement in NP size from 7.67 nm to 6.52 nm and 5.35 nm to 5.17 nm with increasing 5 % to 80 % of metal (Ni, Co) dopant respectively. The optical characteristics, including the absorption spectra of the prepared sample were observed through UV–Vis spectroscopy, Meanwhile SEM confirmed the observation of composition change in specimen with metal (Ni, Co) dopant concentration. The bandgap value was also found decrement 5.23 eV to 5.05 eV with increment of metal (Ni, Co) dopant concentration. The functional groups were measured by Fourier transformation infrared spectroscopy (FTIR). FTIR peaks found the metal (Ni, Co) doped ZnO with the vibration mode of (Zn²⁺ –O^2?) ions due to the increment of dopant concentrations. Furthermore, electrical results show the ohmic behavior of prepared samples. These findings indicate the possibility of tuning optical, structural and electrical properties of metal (Ni, Co) doped ZnO with various dopant concentrations of Nickel and will have great potential to find application in optoelectronic devices.     

Structure,surface analysis and bioactivity of Mn doped zinc oxide nanoparticles

Undoped zinc oxide nanoparticles and Mn (5 atomic % & 10 atomic %) doped zinc oxide nanoparticles were prepared by soft chemical method. Antibacterial, antioxidant and anticancer activities in breast cancer cell line MDAMB231 of prepared nanoparticles were investigated. The nanoparticles were characterized using XRD, SEM, EDAX, UV–Vis, FT-IR, and room temperature PL Analysis. Antimicrobial activity was tested against both gram positive and gram negative human pathogens. The antioxidant potential of prepared nanoparticles was estimated using Phosphomolybdate and DPPH assay. The MTT assay was used for cytotoxicity evaluation of prepared nanoparticles against breast cancer cell line MDAMB231. XRD patterns confirmed the nanoparticles were crystallized hexagonal wurtzite structure with an average size of 38.95 ?nm. The absorption wavelength was observed at 361 ?nm in UV–Vis spectrum of Mn (10 atomic %) doped ZnO nanoparticles. The Mn (5 atomic %) doped ZnO nanoparticles exhibited significant antibacterial activity against the gram negative bacteria Escherichia coli, Klebsiella pneumonia at all concentrations. Undoped zinc oxide nanoparticles and Mn doped zinc oxide nanoparticles were effective against the breast cancer cell line MDAMB231.     

Combustion synthesis of calcium doped ZnO nanoparticles for the photocatalytic degradation of methylene blue dye

ZnO nanoparticles are one of the prominent photocatalysts for environmental applications due to its high redox ability, nontoxic and higher stability. This report explains the synthesis of ZnO nanoparticles by a simple solution combustion method using zinc nitrate hexahydrate as an oxidizing agent and incense stick powder as fuel at 400 °C. Several techniques were adopted for the characterization of the obtained product. X-ray diffraction (XRD) pattern shows that a lower concentration of fuel gives pure ZnO and a higher concentration of fuel results in calcium doped ZnO with a cubic phase having a crystallite size of 32–28 nm. UV–vis spectrum shows that as the fuel concentration increases, band gap decreases and reaches to 3.33 eV for 3 g of fuel. Spongy networks with many pores wereobserved in the scanning electron microscope (SEM) and transmission electron microscope (TEM) images showed the average particle size of Ca doped ZnO NPs is about 20 nm. Pure and Ca doped ZnO nanoparticles were examined for photocatalytic degradation of methylene blue (MB) dye under UV light irradiation. The results prove that Ca doped ZnO nanoparticles show good photocatalytic activity.     

Electrical,optical and photocatalytic properties of Ti-loaded ZnO/ZnO and Ti-loaded ZnO nanospheres

Ti-loaded ZnO and Ti-loaded ZnO/ZnO nanoparticles have been synthesized by sol–gel method and analyzed for photocatalyst application. The phase confirmation was analyzed by powder XRD and surface morphology with HR-SEM and EDAX spectrum. The particle size measured using HR-TEM and SAED pattern confirms the crystalline nature of Ti-loaded ZnO and Ti-loaded ZnO/ZnO nanoparticles. The optical properties were studied with UV–visible diffuse reflectance spectra. The DRS of Ti-loaded ZnO/ZnO nanoparticles are similar to those of pristine ZnO nanoparticles. The KM plots show both the synthesized Ti-loaded ZnO/ZnO and Ti-loaded ZnO exhibit in UV-A region. The electric properties are studied with impedance analyzer, and the results show the charge-transfer resistance of Ti-loaded ZnO/ZnO is larger than that of Ti-loaded ZnO nanoparticles. The photocatalytic activity was studied with methylene blue dye and phenol degradation by Ti-loaded ZnO/ZnO, Ti-loaded ZnO, TiO₂ and ZnO nanoparticles. The photocatalytic activity of Ti-loaded ZnO/ZnO nanospheres is slightly higher than that of other nanoparticles, which shows that they have excellent application as photocatalyst.     

Co doped ZnO nanowires as visible light photocatalysts

High aspect ratio cobalt doped ZnO nanowires showing strong photocatalytic activity and moderate ferromagnetic behaviour were successfully synthesized using a solvothermal method and characterized by scanning electron microscopy (SEM), X-ray powder diffraction (XRD), X-ray photoelectron spectroscopy (XPS), X-ray absorption spectroscopy (XAS), vibrating sample magnetometry (VSM) and UV–visible absorption spectroscopy. The photocatalytic activities evaluated for visible light driven degradation of an aqueous methylene orange (MO) solution were higher than for Co doped ZnO nanoparticles at the same doping level and synthesized by the same synthesis route. The rate constant for MO visible light photocatalytic degradation was 1.9·10⁻³ min⁻¹ in case of nanoparticles and 4.2·10⁻³ min⁻¹ in case of nanowires. We observe strongly enhanced visible light photocatalytic activity for moderate Co doping levels, with an optimum at a composition of Zn_0.95Co_0.05O. The enhanced photocatalytic activities of Co doped ZnO nanowires were attributed to the combined effects of enhanced visible light absorption at the Co sites in ZnO nanowires, and improved separation efficiency of photogenerated charge carriers at optimal Co doping.     

Sol-gel preparation and characterization of Co/TiO<Subscript>2</Subscript> nanoparticles: Application to the degradation of methyl orange

Cobalt doped titania nanoparticles were synthesized by sol-gel method using titanium(IV) isopropoxide and cobalt nitrate as precursors. X-Ray diffraction (XRD) results showed that titania and Co/TiO₂ nanoparticles only include anatase phase. The framework substitution of Co in TiO₂ nanoparticles was established by XRD, scanning electron microscopy equipped with energy dispersive X-ray microanalysis (SEM-EDX) and Fourier transform infrared (FT-IR) techniques. Transmission electron microscopy (TEM) images confirmed the nanocrystalline nature of Co/TiO₂. The increase of cobalt doping enhanced “red-shift” in the UV-Vis absorption spectra. The dopant suppresses the growth of TiO₂ grains, agglomerates them and shifts the band absorption of TiO₂ from ultraviolet (UV) to visible region. The photocatalytic activity of samples was tested for degradation of methyl orange (MO) solutions. Although the photocatalytic activity of undoped TiO₂ was found to be higher than that of Co/TiO₂ under UV irradiation, the presence of 0.5% Co dopant in TiO₂ resulted in a catalyst with the highest activity under visible irradiation.     

Synthesis of Mg-Doped TiO2 nanoparticles under different conditions and its photocatalytic activity

In this study, TiO(2)- and Mg-doped TiO(2) nanoparticles with different dopant contents were prepared by sol-gel method. The prepared photocatalysts were characterized with X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Brunauer-Emmett-Teller (BET) and diffuse reflectance spectroscopy (DRS) techniques. The results of BET analysis indicated a pore diameter of 8 nm and surface area of 48.5 m(2) g(-1). XRD patterns of pure and doped TiO(2) nanoparticles at 450 °C revealed that all phases are anatase. The particle size obtained from TEM was less than 20 nm. The band gap energy of Mg-doped TiO(2) nanoparticles was lower than that of TiO(2) . The photocatalytic activity of the pure and doped nanoparticles has been compared in the removal of C.I. Acid Red 27 (AR27). The photocatalytic activity of Mg-doped (0.2 mol%) TiO(2) for the degradation of AR27 was higher than that of bare TiO(2) nanoparticles. Results of total organic carbon analysis and changes in the AR27 UV-Vis peaks indicated 99% mineralization and extinguishing of all peaks in UV and visible regions is possible with Mg-doped TiO(2) nanoparticles. Removal efficiency of AR27 was sensitive to the parameters such as catalyst dose, pollutant concentration and light intensity.     

Magnesium doped ZnO nanoparticles embedded ZnO nanorod hybrid electrodes for dye sensitized solar cells

We report a novel type of Mg doped ZnO nanoparticles (ZMP) embedded on hydrothermally grown ZnO nanorod (ZR) based photoanode dye sensitized solar cells. The crystallinity, composition and morphology of the photoanodes were characterized by using X-ray diffraction analysis, X-ray photoelectron spectroscopy and scanning electron microscopy. The amount of dye absorbed in the photoanode was observed using UV visible spectral analysis. The improved internal resistance and charge-transfer kinetics of the fabricated cells were analyzed using electrochemical impedance spectroscopy. The ZMP embedded electrode of low thickness (~2.5 μm) gained an enhanced short-circuit current density of 8.56 mA/cm², open-circuit photo voltage of 0.71 V, fill factor of 0.51, and overall conversion efficiency of 2.91 % under 1 sun illumination. This shows high conversion efficiency and performance than that of ZnO nanorod (η ~ 0.22 %) and bare ZnO nanoparticles (ZP) embedded ZnO nanorod (η ~ 1.04 %) based cells. The presence of Mg ions in the ZnO nanoparticle hinders the interfacial recombination of the photo-excited electrons with the electrolyte and also shows better dye absorption than that of ZR. These factors can significantly enhance solar-cell performance and increase the efficiency of the ZMP based dye sensitized solar cells.     

Corallocarpus epigaeus mediated synthesis of ZnO/CuO integrated ZrO2 nanoparticles for enhanced in-vitro antibacterial,antifungal and antidiabetic activities

Zirconia based nanocomposites have attracted much research attention in recent years due to their exceptional biomedicinal activities. Rhizome extracts of Corallocarpus epigaeus based ZrO₂/CuO–ZnO nanocomposite were green synthesized in a facile synthesis strategy. The nanocomposites were examined with XRD technique for their structural information and FT-IR technique for surface functional group analysis. Electron microscopic images aided to elucidate the CuO and ZnO nanoparticles decorated ZrO₂ nanostructures. UV–vis absorption spectroscopic studies of the nanocomposite revealed the characteristic UV absorption of ZrO₂ and enhanced visible region absorption for the incorporated nanoparticles. Antibacterial and antifungal studies indicated enhanced activity of nanocomposites over the pristine zirconia nanoparticles. ZrO₂/CuO–ZnO nanocomposite had exhibited about 75% of α-amylase inhibition activity, whereas pristine ZrO₂ nanoparticles had exhibited only 57% suggesting the worthwhile application in the antidiabetic activity of the nanocomposite.     

Co掺杂ZnO纳米棒的水热法制备及其光致发光性能

以Zn(NO3)2·6H2O 和Co(NO3)2·6H2O为原料, 通过水热法在较低温度下制备了纯ZnO和Co掺杂的ZnO(ZnO:Co)纳米棒. 利用XRD、EDS、TEM和HRTEM对样品进行了表征, 结合光致发光(PL)谱研究了样品的PL性能. 结果表明, 水热法制备纯ZnO和ZnO:Co纳米棒均具有较好的结晶度. Co2+是以替代的形式进入ZnO晶格, 掺入量为2%(原子分数)左右. 纯的ZnO纳米棒平均直径约为20 nm, 平均长度约为180 nm; 掺杂样品的平均直径值约为15 nm, 平均长度约为200 nm左右; Co掺杂轻微地影响ZnO纳米棒的生长. 另外, Co掺杂能够调整ZnO纳米棒的能带结构、提高表面态含量, 进而使得ZnO:Co纳米棒的紫外发光峰位红移, 可见光发光能力增强.     

Enhancement of optical conductivity in the ultra-violet region of Cs doped ZnO sol gel thin films

Nano crystalline cesium (Cs) doped ZnO thin films were deposited on glass substrate by sol gel spin coating method with 1–3 mol.% doping concentration and different annealing temperatures. The deposited films were characterized by X-ray diffraction (XRD), Hall Effect, Photoluminescence (PL) and UV–Visible studies. XRD measurements reveal that all the samples abound in the wurtzite structure with polycrystalline nature. An increase in crystalline size from 19.60 to 44.54 nm is observed with the increase of doping concentration. Electrical conductivity of Cs doped ZnO films were observed from Hall effect measurements and the maximum carrier concentration obtained is 7.35 × 10¹⁸ cm^?3. The near band emission (384 nm) peak intensity increases with the increase of Cs doping concentration and a maximum intensity 55,280 was observed for CZ3 film from PL spectrum. Also a low energy near infrared (NIR) emission peak centered at 1.62 eV appears for the Cs doped ZnO films. The average transmission of CZ film is 88 % and the absorption edge is red shifted with the increase of Cs doping concentration and also the optical conductivity increases in the UV region.     

Enhanced photocatalytic activity of ZnO nanoparticles by surface modification with KF using thermal shock method

ZnO nanoparticles were modified with KF using thermal shock method at various temperatures in order to improve the photocatalytic activity of ZnO under both UVA and visible light irradiation. The influences of KF-modification on the crystal structure, morphology, UV–visible absorption, specific surface area as well as surface structure of ZnO were respectively characterized by XRD, FE-SEM, UV–Visible diffuse reflectance, N₂ adsorption and XPS spectroscopy. The photocatalytic activity was evaluated via the degradation of methylene blue under UVA irradiation. According to the results, the thermal shock process with KF did not modify the structure, the particle size and the optical properties of ZnO nanoparticles but successfully increase their UVA and visible light induced photocatalytic activity. This enhancement of activity may be attributed to the increase of surface hydroxyl groups and zinc vacancies of modified ZnO samples.     

Effect of ZnO nanoparticles doping on structural,dielectric and interfacial behavior of polyoxyethylene (20) sorbitan/ethylene glycol lyotropic phases

ABSTRACT

We are reporting on the interaction of zinc oxide (ZnO) nanoparticles (NPs) with the lyotropic phase comprises of Polyoxyethylene (20) sorbitan monolaurate and protic solvent ethylene glycol. The concentration of the NPs has been varying from 0.05 to 0.5 wt%. Multiwall lamellar and inverse phases have been observed at lower and higher concentration of ZnO NPs doping. Interestingly, the organization of ZnO NPs on the periphery and inside the periphery of ring-like structures has been observed at lower and higher concentration of the dopant, respectively. Such organization of the NPs can be explained considering interfacial interaction amid host and dopant and may also attribute to the adsorption mechanisms of surfactant. Effects of NPs doping on the dielectric dynamics has also been examined. About 32.6% decrease in the dielectric permittivity has been noticed at higher NPs doping. Such decrement in permittivity could be a result of the screening of the ZnO NPs dipole moment by the adsorption of surfactant molecules on their surface. Relaxation and optical parameters of the non-doped and doped mixtures have also been discussed.     

Improved efficiency of dye-sensitized solar cells by design of a proper double layer photoanode electrodes composed of Cr-doped TiO2 transparent and light scattering layers

A new strategy for enhancing the efficiency of TiO₂ dye-sensitized solar cells (DSSCs) by design of a new double layer film doped with Cr ions, with various morphologies, is reported. X-ray diffraction and field emission scanning electron microscope (FE-SEM) analyses revealed that the synthesized nanoparticles had uniform and nanometer grains with different phase compositions and average crystallite size in the range of 10–12 nm depending upon Cr atomic percentage. UV–vis absorption showed that Cr introduction enhanced the visible light absorption of TiO₂ nanoparticles by shifting the absorption onset to visible light region. Furthermore, the band gap energy of nanoparticles decreased with an increase in dopant concentration due to reduction of particle size. It was found that, 3 at.% Cr-doped TiO₂ DSSC in the form of a double-layer film composed of TiO₂ nanoparticles, as the under-layer, and mixtures of nano- and micro-particles with weight ratio of 80:20, as the over-layer, (i.e., CT3/NM3 solar cell) had the highest power conversion efficiency of 7.02 %, short current density of 17.32 mA/cm² and open circuit voltage of 674 mV. This can be related to achievement of a balance among the electron injection, light scattering effect and dye sensitization parameters. Optimization of light scattering effect of photoanode electrode led to improve the photovoltaic performance of CT3/NM3 double-layer solar cell and was demonstrated by diffuse reflectance spectroscopy. The presented strategy would open up new insight into fabrication of low-cost TiO₂ DSSCs with high power conversion efficiency.     

Experimental and Theoretical Study of Enhanced Photocatalytic Activity of Mg‐Doped ZnO NPs and ZnO/rGO Nanocomposites

A systematic experimental and theoretical study of the origin of the enhanced photocatalytic performance of Mg‐doped ZnO nanoparticles (NPs) and Mg‐doped ZnO/reduced graphene oxide (rGO) nanocomposites has been performed. In addition to Mg, Cd was chosen as a doping material for the bandgap engineering of ZnO NPs, and its effects were compared with that of Mg in the photocatalytic performance of ZnO nanostructures. The experimental results revealed that Mg, as a doping material, recognizably ameliorates the photocatalytic performance of ZnO NPs and ZnO/graphene nanocomposites. Transmission electron microscopy (TEM) images showed that the Mg‐doped and Cd‐doped ZnO NPs had the same size. The optical properties of the samples indicated that Cd narrowed the bandgap, whereas Mg widened the bandgap of the ZnO NPs and the oxygen vacancy concentration was similar for both samples. Based on the experimental results, the narrowing of the bandgap, the particle size, and the oxygen vacancy did not enhance the photocatalytic performance. However, Brunauer–Emmett–Teller (BET) and Barret–Joyner–Halenda (BJH) models showed that Mg caused increased textural properties of the samples, whereas rGO played an opposite role. A theoretical study, conducted by using DFT methods, showed that the improvement in the photocatalytic performance of Mg‐doped ZnO NPs was due to a higher electron transfer from the Mg‐doped ZnO NPs to the dye molecules compared with pristine ZnO and Cd‐doped ZnO NPs. Moreover, according to the experimental results, along with Mg, graphene also played an important role in the photocatalytic performance of ZnO.     

Microwave-assisted synthesis of water-soluble styrylpyridine dye-capped zinc oxide nanoparticles for antibacterial applications

ZnO nanoparticles were successfully synthesized using a microwave method, whose surface was modified with {4-[(E)-2-(furan-2-yl)ethenyl]pyridin-1-ium-1-yl}acetate as a capping agent (1 and 3%). Their structural properties were investigated using FTIR, XRD, SEM, EDS, and UV–visible spectroscopy. XRD confirmed the Wurtzite structure for all compounds, a size of 30.6 nm for uncapped and 22.9 nm for 3% dye-capped nanoparticles were calculated from Scherer's equation. Hexagonal wurtzite shape of nanoparticles can be clearly seen in the SEM images. The DFT calculations were carried out using quantum espresso. These dye-capped ZnO nanoparticles were proved to be potential antibacterial agents, the minimum concentrations of dye-capped ZnO nanoparticles that inhibit the growth of bacteria are 1.5 mg/mL for Escherichia coli and 0.78 mg/mL for Bacillus subtilis, which are much lower than those of uncapped ZnO. The bioactivity data suggest these organic–inorganic hybrid nanoparticles emerged as a new class of antibacterial agents.     

Facile fabrication of ZnO/N‐doped helical carbon nanotubes composites with enhanced photocatalytic activity toward organic pollutant degradation

Novel ZnO/N‐doped helical carbon nanotubes (ZnO/N‐HCNTs) composites were successfully synthesized via a facile chemical precipitation approach at room temperature. The sample was well characterized by X‐ray diffraction (XRD), energy dispersive X‐ray spectroscopy (EDS), transmission electron microscopy (TEM) and ultraviolet–visible diffuse reflectance spectroscopy (UV–vis DRS). The photocatalytic activity was evaluated in the degradation of methylene blue (MB) aqueous solution under UV light irradiation. It is found that ZnO nanoparticles were highly and uniformly anchored on the surface and inner tubes of the N‐HCNTs with size of about 5 nm, and significantly enhanced the photocatalytic activity compared to pure ZnO. The enhanced photocatalytic activity of ZnO/N‐HCNTs composites can be ascribed to the integrative synergistic effect of effective interfacial hybridization between N‐HCNTs and ZnO nanoparticles and the prolonged lifetime of photogenerated electron–hole pairs. Moreover, the ZnO/N‐HCNTs could be easily recycled without any obvious decrease in photocatalytic activity and could be promote their application in the area of environmental remediation.     

Consequence of doping mediated strain and the activation energy on the structural and optical properties of ZnO:Cr nanoparticles

We report on the sol-gel synthesis of Zn_1−xCr_xO (x=0.0, 0.05, 0.10, 0.15 and 0.20) nanoparticles. These nanoparticles were characterized by using thermogravimetry/differential scanning calorimetry (TG/DSC), X-ray diffraction (XRD), transmission electron microscopy (TEM), Raman and Photoluminescence (PL). Electronegativity of Cr ions (Cr³⁺) reduces the final decomposition temperature by 40 °C and activation energy of the reaction when Cr is doped into ZnO. Doping of higher Cr concentration (x≥0.10) into ZnO shows formation of secondary spinel (ZnCr₂O₄) phase along with the hexagonal (ZnO) and is revealed by XRD. Formation of secondary phase changes the activation energy of the reaction and thus the strain in ZnO lattice. In Raman spectra, additional Raman modes have been observed for Zn_1−xCr_xO nanoparticles, which can be assigned to the modes generated due to Cr doping. The Cr doping into ZnO is also supported by PL, in which vacancies are formed with Cr ion incorporation and emission band shifts towards higher wavelength.     

Enhancement of the photocatalytic activity of modified ZnO nanoparticles with manganese additive

ZnO nanoparticles were synthesized under mild hydrothermal conditions (T = 150 °C, P = autogenous, experimental duration = 18 h). Manganese was added as an additive to ZnO nanoparticles in different molar percentages. In situ surface-modification was successfully carried out for these manganese-added ZnO nanoparticles using n-butylamine as a surface modifier. The modified manganese-added ZnO nanoparticulates are hydrophilic in nature and are well dispersed in various solvents. The modified nanoparticles were characterized using powder XRD, FTIR, SEM, Zeta potential, and UV?CVis spectrophotometry. The characterization results indicated tailoring of the morphology and size of the nanoparticles, and changing the surface chemistry of the nanoparticles synthesized. The SEM results show that the surface modified manganese-added ZnO nanoparticles have a very thin layer of organic coverage around the inorganic nanoparticles, thus, giving rise to hybrid nanoparticles. The photodegradation of Brilliant Blue dye under sunlight showed the higher efficiency of the modified manganese-doped ZnO nanoparticles compared to the reagent-grade ZnO.