Cloud point extraction and simultaneous spectrophotometric determination of V(V), Co(II) and Cu(II) ions in water samples by 5-Br-PADAP using partial least squares regression

In this work, a new method has been proposed to simultaneously determine V(V), Co(II) and Cu(II) ions from aqueous solution by spectrophotometry after cloud point extraction using partial least squares regression (PLS). The metal ions in 10 ml of aqueous solution (containing 0.2 M sodium acetate buffer solution, pH 3.5) were formed complexes with 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol (5-Br-PADAP). Then, Triton X-114 (2 %, v/v) was added to the solution. By increasing the temperature of the solution up to 55 °C, a phase separation occurred. After centrifugation at 3,000 rpm for 10 min, the surfactant-rich phase was dissolved and diluted to 0.5 mL with ethanol. The metal ions were then determined using spectrophotometry. At these optimal extraction and operating conditions, linearity was obeyed in the range 7–300, 3–100 and 15–700 ng mL^?1 of V(V), Co(II) and Cu(II), with the detection limit of 2.2, 1.0 and 4.5 ng mL^?1, respectively. The relative predictive error for the simultaneous determination of 15 test samples of different concentrations of V(V), Co(II) and Cu(II) was 3.28, 3.64 and 4.04 %, respectively. The root mean square error of prediction for applying the PLS method to 15 synthetic samples in the linear ranges of these metal ions was 3.4, 1.6 and 18.1 ng mL^?1. The interference effect of some anions and cations was also tested. The proposed method has been applied successfully to the simultaneous determination of V(V), Co(II) and Cu(II) ions in real matrix samples with the recoveries of 96.75–104.80 %.     

Application of Multivariate Calibration Methods for the Simultaneous Multiwavelength Spectrophotometric Determination of Fe(II), Cu(II), Zn(II), and Mn(II) in Mixtures

Abstract

A sensitive method for the simultaneous spectrophotometric determination of Fe(II), Cu(II), Zn(II), and Mn(II) in mixtures has been developed with the aid of multivariate calibration methods, such as classical least squares (CLS), principal component regression (PCR) and partial least squares (PLS). The method is based on the spectral differences of the analytes in their complexation reaction with 4‐(2‐pyridylazo)‐resorcinol (PAR) and the use of full spectra with wavelengths in the range of 300–600 nm. It was found that both the spectral positive and negative bands obtained against the PAR blank, are proportional to the concentration for each metal complex. The obtained linear calibration concentration ranges are 0.025–0.6, 0.05–0.8, 0.025–0.8, and 0.05–0.8 µg ml^?1 for Fe(II), Cu(II), Zn(II), and Mn(II), respectively, and the LODs for the four metal ions were found to be approximately 1–3×10^?2 µg ml^?1. The proposed method was applied to a verification set of synthetic mixtures of these four metal ions, with models built in three different wavelength ranges, i.e., 300–450, 450–600, and 300–600 nm, corresponding to the positive, negative bands and their combinations, respectively. It was shown that the PLS model for the 300–600 nm range gave the best results (RPE_T=6.9% and average recovery ～100%; cf. PCR: RPE_T=9.5% and average Recovery ～110%). This method was also successfully applied for the determination of the four metal ions in pharmaceutical preparations, chicken feedstuff, and water samples.     

Synthesis and application of a novel magnetic nanosorbent for determination of trace Cd(II), Ni(II), Pb(II), and Zn(II) in environmental samples

In this work for the first time, Fe₃O₄@SiO₂ core–shell nanoparticles functionalized with isatin groups as a magnetic nanosorbent was applied for the simultaneous extraction of trace amounts of cadmium(II), nickel(II), lead(II), and zinc(II). The characterization of this nanosorbent was studied using Fourier transform infrared spectroscopy, scanning electron microscopy, energy-dispersive X-ray spectrometry, X-ray diffraction, vibrating sample magnetometer and thermogravimetric analysis. The effect of several factors such as pH, amount of sorbent, extraction time, type and volume of the eluent, sample volume, sorption capacity, and potentially interfering ions was investigated. In the selected conditions, it was observed that the limits of detection were 0.11 ng mL^?1 for Cd(II), 0.28 ng mL^?1 for Ni(II), 0.47 ng mL^?1 for Pb(II), and 0.21 ng mL^?1 for Zn(II), and the maximum sorption capacity of this suggested magnetic nanosorbent was 120, 112, 100, and 100 mg g^?1 for Cd(II), Ni(II), Pb(II), and Zn(II), respectively. Also, the precision of the method (RSD%) for ten replicate measurements was found 2.5, 2.5, 2.8, and 3.1%, for Cd(II), Ni(II), Pb(II), and Zn(II) ions, respectively. Finally, the suggested procedure was applied for determination of cadmium(II), nickel(II), lead(II), and zinc(II) at trace levels in different water and agricultural products with satisfactory results.     

4-Hydroxy-3,5-pyridinedicarboxylic Acids: Synthesis,Complexation Properties Towards Fe(III), Al(III), Cu(II), Zn(II), Human Serum Albumin,and Cellular Toxicity

4-hydroxy-3,5-pyridinedicarboxylic acid (DQ58) and 4-hydroxy-1-methyl-3,5-pyridinedicarboxylic acid (DQ71508) have been synthesized, and their Fe(III), Al(III), Cu(II), and Zn(II) coordination properties have been studied by potentiometry, UV–Vis spectroscopy (in the case of Fe(III), Al(III), Cu(II)), ¹H-NMR (for Al(III)) and EPR (for Cu(II)). The thermodynamic results were used to model the extent of the toxic metal ions decorporation (Fe(III) or Al(III)) in the presence of the essential metal ions (Cu(II) or Zn(II)). DQ58 and DQ71508 were demonstrated to interact with human serum albumin (HSA), which is assumed to be the main serum transporter of the chelators, and binding constants have been obtained by ultrafiltration. IC₅₀ values of 5.185 × 10^?3 and 1.033 × 10^?3 mol·L^?1 were collected after 24 and 48 h of treatment with DQ71508 towards human embryonic kidney HEK-293 cells, demonstrating the relatively low cytotoxicity of this compound. According to these results, both DQ58 and DQ71508 seem to be potential candidates for Fe chelation therapy, and DQ58 is a better Fe(III) chelator than DQ71508.     

Amberlite XAD-7 impregnated with Xylenol Orange: a chelating collector for preconcentration of Cd(II), Co(II), Cu(II), Ni(II), Zn(II) and Fe(III) ions prior to their determination by flame AAS

A new chelating resin, Xylenol Orange coated Amberlite XAD-7, was prepared and used for preconcentration of Cd(II), Co(II), Cu(II), Fe(III), Ni(II) and Zn(II) prior to their determination by flame atomic absorption spectrophotometry. The optimum pH values for quantitative sorption of Cd(II), Co(II), Cu(II), Fe(III), Ni(II) and Zn(II) are 4.5–5.0, 4.5, 4.0–5.0, 4.0, 5.0 and 5.0–7.0, respectively, and their desorptions by 2 mol L^–1 HCl are instantaneous. The sorption capacity of the resin has been found to be 2.0, 2.6, 1.6, 1.6, 2.6 and 1.8 mg g^–1 of resin for Cd, Co, Cu, Fe, Ni and Zn, respectively. The tolerance limits of electrolytes, NaCl, NaF, NaI, NaNO₃, Na₂SO₄ and of cations, Mg²⁺ and Ca²⁺ in the sorption of the six metal ions are reported. The preconcentration factor was between 50 and 200. The t_1/2 values for sorption are found to be 5.3, 2.9, 3.2, 3.3, 2.5 and 2.6 min for the six metals, respectively. The recoveries are between 96.0 and 100.0% for the different metals at preconcentration limits between 10 to 40 ng mL^–1. The preconcentration method has been applied to determine the six metal ions in river water samples after destroying the organic matter (if present in very large amount) with concentrated nitric acid (RSD ≤ 8%, except for Cd for which it is upto 12.6%) and cobalt content of vitamin tablets with RSD of ～ 3.0%.     

Silica gel surface modified with sulfanilamide for selective solid-phase extraction of Cu(II), Zn(II) and Ni(II)

A new chelating matrix has been prepared by immobilising sulfanilamide (SA) on silica gel (SG) surface modified with 3-chloropropyltrimethoxysilane as a sorbent for the solid-phase extraction (SPE) Cu(II), Zn(II) and Ni(II). The determination of metal ions in aqueous solutions was carried out by inductively coupled plasma optical emission spectrometry (ICP-OES). Experimental conditions for effective sorption of trace levels of Cu(II), Zn(II) and Ni(II) were optimised with respect to different experimental parameters using the batch and column procedures. The presence of common coexisting ions does not affect the sorption capacities. The maximum sorption capacity of the sorbent at optimum conditions was found to be 34.91, 19.07 and 23.62 mg g^?1 for Cu(II), Zn(II) and Ni(II), respectively. The detection limit of the method defined by IUPAC was found to be 1.60, 0.50 and 0.61 µg L^?1 for Cu(II), Zn(II) and Ni(II), respectively. The relative standard deviation (RSD) of the method under optimum conditions was 4.0% (n = 8). The method was applied to the recovery of Cu(II), Zn(II) and Ni(II) from the certified reference material (GBW 08301, river sediment) and to the simultaneous determination of these cations in different water samples with satisfactory results.     

Impact of environmental conditions on the sorption behavior of Pb(II) onto attapulgite

This paper examined the application of attapulgite as an adsorbent for the removal of Pb(II) from heavy metal-contaminated water under various conditions. The sorption results indicated that the sorption of Pb(II) on attapulgite was strongly dependent on ionic strength at pH < 7.0. Outer-sphere surface complexation or ion exchange may be the main sorption mechanism of Pb(II) on attapulgite at low pH values. No drastic difference of Pb(II) sorption was observed at pH 7.0–10.0, and the sorption at pH > 10.0 was mainly dominated by inner-sphere surface complexation. The sorption of Pb(II) on attapulgite was affected by foreign ions in solution at pH < 7.0, and was not affected by foreign ions at pH > 7.0. The thermodynamic parameters (ΔH°, ΔS° and ΔG°) were evaluated from the temperature-dependent sorption isotherms, and the results indicated that the sorption process of Pb(II) on attapulgite was spontaneous and endothermic in nature.     

Kinetics study of selective removal of lead(II) in an aqueous solution containing lead(II), copper(II) and cadmium(II) across bulk liquid membrane

Transport of Pb(II) ion from equimolar aqueous solutions of Pb(II), Cu(II) and Cd(II) as well as from aqueous solutions containing only Pb(II) source phase (C_metal = 1.0 × 10^?4 mol L^?1) through bulk liquid membranes containing crown ether and oleic acid as carrier has been investigated. The initial fluxes of transported metal ions depend on the hydrophile–lipophile balance (HLB) and molar volumes (Vx) of crown ethers. The initial fluxes of Pb(II), Cu(II), and Cd(II) decrease with increase of HLB value for azacrown ether, i.e., tetraaza-14-crown-4 (A₄14C4), L1 > benzo-15-crown-5 (B15C5), L2 > 4′-Aminobenzo-15C5, L3 > nitrobenzo-15-crown-5 (NB15C5), L4. The selectivity of the metal ions showed the following separation factors (SF): SF_Pb–Cu = 2.15, SF_Cu–Cd = 2.10, SF_Pb–Cd = 4.52. The highest transport recovery for Pb(II) was observed for L1 (99.3 %).     

Fullerene-based anodic stripping voltammetry for simultaneous determination of Hg(II), Cu(II), Pb(II) and Cd(II) in foodstuff

Various carbon nanomaterials for use in anodic stripping voltammetric analysis of Hg(II), Cu(II), Pb(II) and Cd(II) are screened. Graphene, carbon nanotubes, carbon nanofibers and fullerene (C₆₀), dispersed in chitosan (Chit) aqueous solution, are used to modify a glassy carbon electrode (GCE). The fullerene-chitosan modified GCE (C₆₀-Chit/GCE) displays superior performance in terms of simultaneous determination of the above ions. The electrodes and materials are characterized by electrochemical impedance spectroscopy, cyclic voltammetry, scanning electron microscopy, Raman spectroscopy, X-ray diffraction and X-ray photoelectron spectroscopy. The excellent performance of C₆₀-Chit/GCE is attributed to the good electrical conductivity, large surface area, strong adsorption affinity and unique crystalline structure of C₆₀. Using differential pulse anodic stripping voltammetry, the assay has the following features for Hg(II), Cu(II), Pb(II) and Cd(II), respectively: (a) Peak voltages of +0.14, ?0.11, ?0.58 and???0.82 V (vs SCE); (b) linear ranges extending from 0.01–6.0 μM, 0.05–6.0 μM, 0.005–6.0 μM and 0.5–9.0 μM; and (c), detection limits (3σ method) of 3 nM (0.6 ppb), 14 nM (0.9 ppb), 1 nM (0.2 ppb) and 21 nM (2.4 ppb). Moreover, the modified GCE is well reproducible and suitable for long-term usage. The method was successfully applied to the simultaneous determination of these ions in spiked foodstuff.

Open image in new window

Graphical abstract Compared with graphene, carbon nanotubes and carbon nanofibers, an electrode modified with fullerene in chitosan electrode displays superior performance for the simultaneous anodic stripping voltammetric detection of Hg(II), Cu(II), Pb(II) and Cd(II).

     

Using xanthated Lagenaria vulgaris shell biosorbent for removal of Pb(II) ions from wastewater

Chemically modified Lagenaria vulgaris shell was applied as a new sorbent for the removal of lead (II) ions from aqueous solution in a batch process mode. The influence of contact time, initial concentration of lead (II) ions, initial pH value, biosorbent dosage, particle size and stirring speed on the removal efficiency was evaluated. Biosorbent characterization was performed by Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX). Four kinetic models (pseudo-first order, pseudo-second order, Elovich model and Intraparticle diffusion model) were used to determine the kinetic parameters. The experimental results were fitted to the Langmuir, Freundlich, Dubinin–Radushkevich and Temkin models of isotherm. Pseudo-second order kinetic model and Langmuir isotherm model best fitted the experimental data. Sorption process is obtained to be fast and equilibrium was attained within 40 min of contact time. The maximum sorption capacity was 33.21 mg g^?1. Biosorption was highly pH-dependent where optimum pH was found to be 5. The results of FTIR and SEM analysis showed the presence of new sulfur functional groups. This study indicated that xanthated Lagenaria vulgaris shell could be used as an effective and low-cost biosorbent for the removal of lead (II) ions from aqueous solution.     

Removal of Trace Contaminants from Water Using New Chelating Resins

Abstract

The modification of cross‐linked polyacrylamide (CPAAm) and incorporation of methyl thiourea (MeTU) or phenyl thiourea (PhTU) group were utilized in the preparation of two new chelating resins CPAAm‐EDA‐MeTU (resin I) and CPAAM‐EDA‐PhTU (resin II), [EDA=ethylenediamine]. The prepared resins were characterized by elemental analysis and IR spectroscopy. The sorption behaviors of Cd(II), Pb(II), and Zn(II) ions on the prepared resins were studied and the optimum sorption conditions for the tested metal ions were determined. The optimum pH value for the sorption of Cd(II) and Zn(II) ions on both resins I and II was ranged between 7–8. The prepared new resins show very little affinity towards Pb(II) ion. The maximum experimental sorption capacities of resin I towards Cd(II) and Zn(II) ions were 3.2 and 0.6 mmol g^?1, respectively, and that of resin II were and 0.6 mmol g^?1 in the same prescribed order. Langmuir and Freundlich isotherm constants and correlation coefficients for the present system were calculated and compared. The thermodynamic parameters (ΔG°, ΔH°, and ΔS°) for cadmium and zinc sorption on the prepared resins were also determined from the temperature dependence.     

Water hyacinth modified carbon paste electrode for simultaneous electrochemical stripping analysis of Cd (II) and Pb (II)

In this study, we demonstrated a highly sensitive electrochemical sensor for the simultaneous detection of Pb (II) and Cd (II) in aqueous solution using carbon paste electrode modified with Eichhornia crassipes powder by square wave anodic stripping voltammetry. The effect of modifier composition, pH, preconcentration time, reduction potential and time, and type of supporting electrolyte on the determination of metal ions were investigated. Pre-concentration on the modified surface was performed at open circuit. The modified electrode exhibited well-defined and separate stripping peaks for Pb (II) and Cd (II). Under optimum experimental conditions, a linear range for both metal ions was from 10 to 5000 μg L^?1 with the detection limits of 4.9 μg L^?1, 2.1 μg L^?1 for Cd(II) and Pb (II), respectively. The modified electrode was found to be sensitive and selective when applied to determine trace amounts of Cd (II) and Pb (II) in natural water samples.     

Polyethyleneimine Methylenephosphonic Acid for the Solid-Phase Sorption of Lead(II)

Abstract

In the first part of this work, polyethyleneimine methylenephosphonic acid (PEIMPA) was used as an effective sorbent for solid-phase extraction of Pb(II) ions from an aqueous solution. Conditions for effective sorption are optimized with respect to different experimental parameters in a batch process. The results showed that the amount of extraction decreases with solution pH in the range between 3.5 and 5.8. The sorption capacity is 609 mg·g^?1. The second part of the study focuses on the recovery of Pb(II) from a synthesized binary solution of Pb(II)–Zn(II) and from real Zn(II)-electrolyzed wastewaters. The presence of Cd(II), Co(II), Cu(II), Fe(III), Ni(II), and Zn(II) in large concentrations has a significantly negative effect on extraction properties.     

Simultaneous determination of cadmium(II), lead(II) and copper(II) by using a screen-printed electrode modified with mercury nano-droplets

We are presenting a strategy for the fabrication of disposable screen-printed electrodes modified with mercury nano-droplets and capable of sensing heavy metal ions. They were prepared by coating electrodes with a mixture of multi-walled carbon nanotubes and chitosan, this followed by adsorption of mercury. The resulting sensor was characterized by cyclic voltammetry and impedance spectroscopy. Also the effects caused by adsorption of mercury were investigated. It is shown that square wave anodic stripping voltammetry enables simultaneous determination of cadmium(II), lead(II) and copper(II), for which detection limits of 12, 23 and 20 nM, respectively, are found. Relative standard deviations for ten determinations at 0.6 µM concentrations of these ions are in the range of 3.0 to 5.7%. The applicability was tested by analyzing river water and showed recoveries between 94.1 and 104.6%, thus demonstrating its utility for in-field monitoring of these heavy metal ions.     

Effective ultrasound-assisted removal of heavy metal ions As(III), Hg(II), and Pb(II) from aqueous solution by new MgO/CuO and MgO/MnO<Subscript>2</Subscript> nanocomposites

A series of new (MgO) _x CuO and (MgO) _x MnO₂ nanocomposites were prepared and used as adsorbent for removal of As³⁺, Hg²⁺, and Pb²⁺ ions from aqueous solution with high capacity and detection limit. These nanocomposites were synthesized with different molar ratios by sonochemical method in alkaline solution using polyvinylpyrrolidone as a capping agent and were characterized by FTIR, AAS, UV–Vis spectroscopy, and TEM and SEM imaging. The maximum heavy metal ions adsorption was achieved for (MgO)_0.32CuO and (MgO)_2.9MnO₂ nanocomposites assisted by 3-min sonication using ultrasound. Adsorbent capacity of (MgO)_0.32CuO reached 500.0 mg/g and detection limit was 0.1 ppb for As³⁺. Also (MgO)_2.9MnO₂ nanocomposite adsorbed 457.1 mg/g of Hg²⁺ and 461.2 mg/g of Pb²⁺. Extremely low detection limits of 1.5 and 2.0 ppb were obtained for Hg(II) and Pb(II) ions, respectively, which are much lower than the WHO allowable limits. So, these nanocomposites should be excellent candidate for heavy metal removal with advantage of high capacity, high sensitivity, cost effectiveness and easy preparation.     

Flame atomic absorption spectrometric determination of Cd(II), Ni(II), Co(II) and Cu(II) in tea and water samples after simultaneous preconentration of dithizone loaded on naphthalene

A simultaneous preconcentration procedure for the determination of Cd(II), Ni(II), Co(II) and Cu(II) by atomic absorption spectrometry is described. The method is based on solid phase extraction of the metal ions on dithizone loaded on naphthalene in a mini-column, elution with nitric acid and determination by flame atomic absorption spectrometry. The sorption conditions including NaOH concentration, sample volume and the amount of dithizone were optimized in order to attain the highest sensitivity. The calibration graph was linear in the range of 0.5–75.0 ng ml^?1 for Cd(II), 1.0–150.0 ng ml^?1 for Ni(II), 1.0–150.0 ng ml^?1 for Co(II) and 1.0–125.0 ng ml^?1 for Cu(II) in the initial solution. The limit of detection based on 3S_b was 0.13, 0.32, 0.33 and 0.43 ng ml^?1 for Cd(II), Ni(II), Co(II) and Cu(II), respectively. The relative standard deviations (R.S.D) for ten replicate measurements of 20 ng ml^?1of Cd(II), 100 ng ml^?1 of Ni(II), Co(II) and 75 ng ml^?1 of Cu(II) were 3.46, 2.43, 2.45 and 3.26%, respectively. The method was applied to the determination of Cd(II), Ni(II), Co(II) and Cu(II) in black tea, tap and river water samples.     

Used a new aza-thia-macrocycle as a suitable carrier in potentiometric sensor of copper (II)

A new modified carbon paste electrode for determination of Cu²⁺ made in our laboratory that used a new synthesized macrocycle 7,16-diaza-1-thia-4,10,13,19-tetraoxa-6,17-dioxo-2,3;20,21-dinaphtho-cyclouneicosane as modifier. This sensor exhibits a good affinity toward copper (II) ions over a wide variety of other metal ions. The electrode exhibits a Nernstian slope of 30 (±0.5) mV per decade for copper (II) ions over a wide concentration range (1.0 × 10^?8–1.0 × 10^?2 mol L^?1), with a limit of detection of 7.0 × 10^?9 mol L^?1 (~0.45 ppb). It has a response time of 30 s and can be used for at least 3 months without any considerable divergence in responses. The potentiometric response of the electrode is independent of the pH of test solution in the pH range 3.5–7.5. Finally, it was successfully used as an indicator electrode for determination of copper (II) in real samples such as Karoun river and tap water.     

Sorption of Copper(II) and Silver(I) by Four Bacterial Exopolysaccharides

Metal remediation was studied by the sorption of analytical grade copper Cu(II) and silver Ag(I) by four exopolysaccharides (EPS) produced by marine bacteria. Colorimetric analysis showed that these EPS were composed of neutral sugars, uronic acids (>20 %), acetate, and sulfate (29 %). Metal sorption experiments were conducted in batch process. Results showed that the maximum sorption capacities calculated according to Langmuir model were 400 mg g^?1 EPS (6.29 mmol g^?1) and 333 mg g^?1 EPS (3.09 mmol g^?1) for Cu(II) and Ag(I), respectively. Optimum pH values of Ag(I) sorption were determined as 5.7. Experiment results also demonstrated the influence of initial silver concentration and EPS concentrations. Microanalyzing coupled with scanning electron microscopy demonstrated the presence of metal and morphological changes of the EPS by the sorption of metallic cations. The Fourier transform infrared spectroscopy analysis indicated possible functional groups (e.g., carboxyl, hydroxyl, and sulfate) of EPS involved in the metal sorption processes. These results showed that EPS from marine bacteria are very promising for copper and silver remediation. Further development in dynamic and continuous process at the industrial scale will be established next.     

Amorphous and ordered organosilicas functionalized with amine groups as sorbents of platinum (II) ions

Two groups of amine-functionalized organosilicas have been synthesized: amorphous polysiloxane xerogels (APX) and ordered mesoporous organosilicas (OMO) by co-condensation of tetraethoxysilane and appropriate alkoxysilanes: aminopropyltriethoxysilane and N-[3-(trimethoxysilyl)propyl]ethylenediamine. The obtained materials were characterized by sorption measurements, X-ray diffractometry, elemental analysis, transmission electron microscopy, and scanning electron microscopy. The OMO samples have well developed porous structure—the values of specific surface area are in the range 740–840 m²/g. While the APX samples are less porous having the corresponding values in the range 280–520 m²/g. The sizes of the ordered mesopores of OMO are in the range 5.9–6.5 nm while for the APX they are 2.9–12.1 nm indicating structural differences between both groups of the samples. All samples were tested as the sorbents of Pt(II) ions. The influence of various parameters such as pH, contact time, equilibrium concentration on Pt(II) adsorption ability onto prepared adsorbents was studied in detail. Additionally, the effect of chloride concentration on Pt(II) adsorption was investigated. The values of static sorption capacities were in the range of 32–102 mg_Pt(II)/g and 20–139 mg_Pt(II)/g for OMO and APX series, respectively.     

A magnetic metal-organic framework as a new sorbent for solid-phase extraction of copper(II), and its determination by electrothermal AAS

We report on the synthesis of Fe₃O₄-functionalized metal-organic framework (m-MOF) composite from Zn(II) and 2-aminoterephthalic acid by a hydrothermal reaction. The magnetic composite is iso-reticular and was characterized by FTIR, X-ray diffraction, SEM, magnetization, and TGA. The m-MOF was then applied as a sorbent for the solid-phase extraction of trace levels of copper ions with subsequent quantification by electrothermal AAS. The amount of sorbent applied, the pH of the sample solution, extraction time, eluent concentration and volume, and desorption time were optimized. Under the optimum conditions, the enrichment factor is 50, and the sorption capacity of the material is 2.4 mg g^?1. The calibration plot is linear over the 0.1 to 10 μg L^?1 Cu(II) concentration range, the relative standard deviation is 0.4 % at a level of 0.1 μg L^?1 (for n?=?10), and the detection limit is as low as 73 ng L^?1. We consider this magnetic MOF composite to be a promising and highly efficient material for the preconcentration of metal ions.