Annealing behavior of gel‐spun polyethylene fibers at temperatures lower than needed for significant shrinkage

The annealing at 373 K of ultrastrong, gel‐spun polyethylene (PE) has been studied. At this temperature, the fibers show no significant shrinkage. Still, a significant decrease in the mechanical properties is observed. The fibers have been analyzed with differential scanning calorimetry (DSC), temperature‐modulated differential scanning calorimetry (TMDSC), atomic force microscopy (AFM), and small‐angle X‐ray scattering (SAXS). During the annealing, the glass transition of the intermediate phase is exceeded, as shown by DSC. When split for structure analysis by AFM, the annealed fibers undergo plastic deformation around the base fibrils instead of brittle fracture. The quasi‐isothermal TMDSC experiments are compared to the minor structural changes seen with SAXS and AFM. The loss of performance of the PE fibers at 373 K is suggested to be caused by the oriented intermediate phase, and not by major changes in the structure or morphology. The overall metastable, semicrystalline structure is shown by TMDSC to posses local regions that can melt reversibly. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 403–417, 2003     

Matching Cure Characteristics of Automotive Rubber Compound and Polyurethane Coating

The present investigation focuses on matching cure characteristics of EPDM rubber compound and polyurethane (PU) coating using temperature modulated and pressure differential scanning calorimetry (TMDSC, PDSC). TMDSC provides a detailed and better understanding of the curing process of model rubber system as well as complex automotive rubber compounds. The low level of unsaturation present in EPDM, results in the small heat of vulcanization (2–5 J g^–1), which is difficult to accurately measure using conventional differential scanning calorimetry (DSC). Thus, curing of highly filled EPDM compound was investigated using TMDSC. The kinetics of PU curing was monitored using pressure DSC (PDSC), and heat of curing was determined as 4.2 J g^–1 at 10°C min^–1 heating rate. It is found that complex automotive compounds and the PU coating are curing simultaneously. This revised version was published online in July 2006 with corrections to the Cover Date.     

Temperature‐modulated differential scanning calorimetry studies on the origin of double melting peaks in isothermally melt‐crystallized poly(L‐lactic acid)

In this work, the melting behaviors of nonisothermally and isothermally melt‐crystallized poly(L ‐lactic acid) (PLLA) from the melt were investigated with differential scanning calorimetry (DSC) and temperature‐modulated differential scanning calorimetry (TMDSC). The isothermal melt crystallizations of PLLA at a temperature in the range of 100–110 °C for 120 min or at 110 °C for a time in the range of 10–180 min appeared to exhibit double melting peaks in the DSC heating curves of 10 °C/min. TMDSC analysis revealed that the melting–recrystallization mechanism dominated the formation of the double melting peaks in PLLA samples following melt crystallizations at 110 °C for a shorter time (≤30 min) or at a lower temperature (100, 103, or 105 °C) for 120 min, whereas the double lamellar thickness model dominated the formation of the double melting peaks in those PLLA samples crystallized at a higher temperature (108 or 110 °C) for 120 min or at 110 °C for a longer time (≥45 min). © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 466–474, 2007     

Analysis of the complex thermal behavior of poly(L‐lactic acid) film. I. Samples crystallized from the glassy state

The melting behavior of poly(L ‐lactic acid) film crystallized from the glassy state, either isothermally or nonisothermally, was studied by wide angle X‐ray diffraction (WAXD), small angle X‐ray scattering (SAXS), differential scanning calorimetry (DSC), and temperature‐modulated differential scanning calorimetry (TMDSC). Up to three crystallization and two melting peaks were observed. It was concluded that these effects could largely be accounted for on the basis of a “melt‐recrystallization” mechanism. When molecular weight is low, two melting endotherms are readily observed. But, without TMDSC, the double melting phenomena of high molecular weight PLLA is often masked by an exotherm just prior to the final melting, as metastable crystals undergo melt‐recrystallization during heating in the DSC. The appearance of a double cold‐crystallization peak during the DSC heating scan of amorphous PLLA film is the net effect of cold crystallization and melt‐recrystallization of metastable crystals formed during the initial cold crystallization. Samples cold‐crystallized at 80 and 90 °C did not exhibit a long period, although substantial crystallinity developed. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3200–3214, 2006     

Melting and crystallization of poly(butylene terephthalate) by temperature‐modulated and superfast calorimetry

Quantitative temperature‐modulated differential scanning calorimetry (TMDSC) and superfast thin‐film chip calorimetry (SFCC) are applied to poly(butylene terephthalate)s (PBT) of different thermal histories. The data are compared with those of earlier measured heat capacities of semicrystalline PBT by adiabatic calorimetry and standard DSC. The solid and liquid heat capacities, which were linked to the vibrational and conformational molecular motion, serve as references for the quantitative analyses. Using TMDSC, the thermodynamic and kinetic responses are separated between glass and melting temperature. The changes in crystallinity are evaluated, along with the mobile–amorphous and rigid–amorphous fractions with glass transitions centered at 314 and 375 K. The SFCC showed a surprising bimodal change in crystallization rates with temperature, which stretches down to 300 K. The earlier reported thermal activity at about 248 K was followed by SFCC and TMDSC and could be shown to be an irreversible endotherm and is not caused by a glass transition and rigid–amorphous fraction, as assumed earlier. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1364–1377, 2006     

示差扫描量热法进展及其在高分子表征中的应用

示差扫描量热法(DSC)是表征材料热性能和热反应的一种高效研究工具,具有操作简便、应用广泛、测量值物理意义明确等优点.近年来DSC技术的发展大大拓展了高分子材料表征的测试范围,促进了对高分子物理转变的热力学和动力学的深入研究.温度调制示差扫描量热法(TMDSC)是DSC在20世纪90年代的标志性进展,它在传统DSC的线性升温速率的基础之上引入了调制速率,从而可将总热流信号分解为可逆信号和不可逆信号两部分,并能测量准等温过程的可逆热容.闪速示差扫描量热法(FSC)是DSC技术近年来的创新性发展,它采用体积微小的氮化硅薄膜芯片传感器替代传统DSC的坩埚作为试样容器和控温系统,实现了超快速的升降温扫描速率以及微米尺度上的样品测试,使得对于高分子在扫描过程中的结构重组机制的分析以及对实际的生产加工条件的直接模拟成为可能.本文从热分析基础出发,依次对传统DSC、TMDSC和FSC进行了介绍,内容覆盖其发展历史、方法原理、操作技巧及其在高分子表征中的应用举例,最后对DSC未来的发展和应用进行了展望.本文希望通过综述DSC原理、实验技巧和应用进展,帮助读者加深对DSC这一常用表征技术的理解,进一步拓展DSC表征高分子材料的应用.     

Reversible and irreversible heat capacity of poly(trimethylene terephthalate) analyzed by temperature‐modulated differential scanning calorimetry

The heat capacity of poly(trimethylene terephthalate) (PTT) has been analyzed using temperature‐modulated differential scanning calorimetry (TMDSC) and compared with results obtained earlier from adiabatic calorimetry and standard differential scanning calorimetry (DSC). Using quasi‐isothermal TMDSC, the apparent reversing and nonreversing heat capacities were determined from 220 to 540 K, including glass and melting transitions. Truly reversible and time‐dependent irreversible heat effects were separated. The extrapolated vibrational heat capacity of the solid and the total heat capacity of the liquid served as baselines for the analysis. As one approaches the melting region from lower temperature, semicrystalline PTT shows a reversing heat capacity, which is larger than that of the liquid, an observation that is common also for other polymers. This higher heat capacity is interpreted as a reversible surface or bulk melting and crystallization, which does not need to undergo molecular nucleation. Additional time‐dependent, reversing contributions, dominating at temperatures even closer to the melting peak, are linked to reorganization and recrystallization (annealing), while the major melting is fully irreversible (nonreversing contribution). © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 622–631, 2000     

Glass transition investigated by a combined protocol using thermostimulated depolarization currents and differential scanning calorimetry

Relaxation times of bisphenol A polycarbonate around the glass transition temperature are estimated using the combination of differential scanning calorimetry (DSC) and thermostimulated depolarization currents (TSDC). These measurements are performed using samples with different thermal histories below and above the vitrification transformation. This protocol enables the extension of the range of equilibrium relaxation times measured by dielectric spectroscopy. By this mean we may recalculate the values of the Kauzmann temperature and fragility index.     

Correlation study among oxygen permeability,molecular mobility,and amorphous structure change of poly(ethylene‐vinylalcohol copolymers) by moisture

Oxygen permeability and the free‐volume hole size (cavity size) of ethylene‐vinylalcohol copolymers (EVOH) indicate abnormal humidity dependence, that is, they have minimum values in the range of around 20–40% RH, not showing a monotonic increase with humidity. To clarify this abnormal phenomenon, we investigated its molecular mobility and amorphous structure change by means of solid‐state NMR and temperature‐modulated differential scanning calorimetry (TMDSC). The glass transition temperature (T_g) decreased with humidity. Specimens stored at 15–60% RH showed large enthalpy relaxation, and it was found that the amorphous structure became more compact and the molecular conformation became more stable by ageing within this range of humidity. Under these conditions, solid‐state NMR measurement showed a component with intermediate relaxation time in the amorphous region. The results obtained by TMDSC and solid‐state NMR showed a reduction in molecular mobility by densifying in the amorphous region under the condition of 15–60% RH. The fact that the oxygen permeability and the cavity size of EVOH indicate minimum values at low humidity are attributed to the reduction in molecular mobility by enthalpy relaxation. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1181–1191, 2009     

Control of thermal cross‐linking reactions and the degree of crystallinity of syndiotactic 1,2‐polybutadiene

Thermal stability, crystallization, morphological development, subsequently melting, and crystallinity control of a syndiotactic 1,2‐polybutadiene sample were carefully carried out by thermogravimetry (TGA), polarized optical microscopy (POM), differential scanning calorimetry (DSC), temperature‐modulated differential scanning calorimetry (TMDSC), and wide‐angle X‐ray diffraction (WAXD), respectively. The experiments indicate that thermal cross‐linking reaction rates under nitrogen protection and in air are different for this polymer at temperature above 155 °C. Under nitrogen protection, the thermal cross‐linking reaction rate is delayed and the mechanism of melt crystallization obtained from the DSC results is in good accordance with that from POM observation. TMDSC results indicate that melting–recrystallization–melting model is more proper to explain the double melting events of this sample. At the same time, the evolution of the degree of crystallinity as the function of the time was investigated by WAXD profiles for the samples firstly crystallized at 145 °C for 1 h and then kept at 163 °C mediated between the temperatures of the double peaks. It shows that as prolonging the annealing time at 163 °C thermal cross‐linking reactions possibly occur, leading to gradual reduction of the apparent crystallite sizes, evaluated by Scherrer equation and the degree of crystallinity. The changing sequence of the relative intensity of the stronger four diffraction peaks with time due to thermal cross‐linking reactions is (111)/(201) > (210) > (010) > (200)/(110). © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2885–2897, 2005     

Dynamical properties of ethylene glycol and glucose studied by temperature-modulated differential scanning calorimetry and Brillouin scattering

The fragility of ethylene glycol and glucose aqueous solution systems has been investigated by temperature-modulated differential scanning calorimetry (TMDSC). The frequency and temperature dependences of complex specific heat have been observed in the vicinity of a glass-transition temperature T _g . It is shown that the value of the fragility index m can be determined from the temperature dependence of the α-relaxation times observed by TMDSC. We have also studied the elastic properties of these aqueous solutions by micro-Brillouin scattering, and determined these relaxation times of elastic properties in the gigahertz range.     

Step-scan TMDSC and high rate DSC study of the multiple melting behavior of poly(1,3-propylene terephthalate)

The multiple melting behavior of poly(1,3-propylene terephthalate) (PPT) samples after isothermal crystallization from the melt was studied. The step-scan temperature-modulated differential scanning calorimetry (TMDSC) and high rate DSC were used to investigate this behavior in conjunction with standard DSC, wide-angle X-ray diffraction (WAXD) and polarizing light microscopy (PLM). The effect of PPT average molecular weight on the melting was also examined. In general multiple endotherms after isothermal crystallization of PPT were attributed to a continuous crystal perfection process during the subsequent heating scan via melting-recrystallization-remelting. Multiple melting behavior was more pronounced for the low molecular weight PPT. Step-scan TMDSC showed that extensive recrystallization occurs in PPT samples, especially after rapid isothermal crystallization. In fact two recrystallization exothermic peaks were observed. High rate DSC revealed the initial morphology generated during the isothermal step and showed that the low and middle peaks are associated with melting of primary crystals while the high temperature peak should be attributed to melting of recrystallized material.     

Thermal history and enthalpy relaxation of an interpenetrating network polymer with exceptionally broad relaxation time distribution

Differential scanning calorimetry (DSC) of an interpenetrating network polymer of composition 25% polyurethane–75% poly(methyl methacrylate) shows a slowly increasing heat capacity, instead of the usual glass transition endotherm, whose onset temperature is not clearly discernible. On aging of the polymer at several temperatures between 193 and 333 K, an endothermic peak is observed whose onset is in the vicinity of the respective temperature of aging. The area under these peaks increases with increasing aging time at a fixed temperature. The effects are attributed to a very broad distribution of relaxation times, which may be represented by either a sum of discrete structural relaxation times of local network arrangement or by a nonexponential relaxation function which is equivalent to a distribution of relaxation times. In either view the vitrified state of the polymer can be envisaged as containing local structures whose own T_gs extend over a wide range of temperature. Aging decreases the enthalpy and produces an endothermic region which resembles an increase in C_p on heating because of relaxation of that local structure. The interpretation is supported by simulation of DSC scans in which the distribution of relaxation times is assumed to be exceptionally broad and in which aging introduced at several temperatures over a wide range produces endothermic effects (or regions of DSC scans) qualitatively similar to those observed for the interpenetrating network polymer. © 1994 John Wiley & Sons, Inc.     

木糖醇玻璃焓松弛的量热分析

为了考察木糖醇的玻璃化转变和焓松弛行为,寻求碳链长度对线性多元醇玻璃化转变和焓松弛行为的影响,利用差示扫描量热(DSC)技术测定了不同降温速率下木糖醇在玻璃化转变温度(Tg)前后的比热容(Cp),通过曲线拟合获得了TNM(Tool-Narayanaswamy-Moynihan)模型参数,并和其他多元醇类已有研究结果进行对照.结果表明,尽管TNM模型可以很好地重现不同降温速率体系的实验比热容数据,但模型参数并不是材料常数,而是和热历史有关,不同的降温速率对应不同的模型参数.指前因子(A)、非线性参数(x)和非指数参数(β)均随着降温速率的增加而降低,松弛活化焓(△h*)的变化趋势刚好相反.几种线性多元醇玻璃化转变和TNM模型参数的对照表明,玻璃化转变温度,松弛活化焓和动力学脆度(m)都随着烷基碳链长度的增加而增加.虽然非线性参数、非指数参数随碳链长度的增加有降低的趋势,但木糖醇展现出反常变化的情形.     

Thermal analysis of protein–metallic ion systems

Advanced thermal analysis methods, such as temperature modulated DSC (differential scanning calorimetry) and quasi-isothermal TMDSC were used to analyze the protein–metallic ion interactions in silk fibroin proteins. The precise heat capacities were measured and theoretically predicted in this study. To remove bound water and simplify the system, a thermal cycling treatment through both standard DSC and TMDSC was used to detect the underlying heat capacity and reveal the phase transitions of the silk–metallic salts system. Results show that K⁺ metallic salts play the role of plasticizer in silk fibroin proteins, which reduces the glass transition (T_g) of the pure silk protein and negatively affects its structural thermal stability. On the other hand, Ca²⁺ metallic salts act as an anti-plasticizer, and increase the glass transition and the thermal stability of the silk protein structure. This indicates that the thermal analysis methods offer a new pathway to study protein–metallic ion systems, yielding very fruitful information for the study of protein structures in the future.     

Molar-mass dependence of apparent relaxation time in melting region of poly(oxytetramethylene)glycol

Melting behaviours of poly(oxytetramethylene)glycols (POTMGs) with different molar masses were investigated by temperature-modulated differential scanning calorimetry (TMDSC) and relaxation times within the melting range were estimated from the modulation-frequency dependence of phase angle δ. An Arrhenius plot of the relaxation times exhibited a plateau in the lower melting peak region of POTMGs with molar masses of 1400, 1000 and 650. This plot was compared with the standard DSC curve. The apparent activation energy was estimated from the relaxation time in the upper and lower sides of a melting temperature region: slight dependence on the molar mass was observed for the former region whereas the maximum value was obtained for a molar mass 1400 for the latter region.     

Influence of annealing and chain defects on the melting behaviour of poly(vinylidene fluoride)

The melting behaviour of poly(vinylidene fluoride) (PVDF) was investigated by differential scanning calorimetry (DSC) and small- and wide-angle X-ray scattering in order to study the influence of the chain defects content and of the temperature of annealing on the crystallization and melting behaviour.All the DSC scans show a double endotherm and the analysis of the data suggests that the low temperature endotherm is due to the melting of a population of thin lamellae, whose thickness increases during the annealing, but a high content of chain defects prevents the lamellar thickening and the main effect in this case is the crystallization of thin lamellae from a portion of polymer which did not crystallize during the quenching from the melt. Furthermore, the two melting endotherms, which are observed, can be partially ascribed to a melting-recrystallization process.Furthermore, stepwise isothermal cooling was performed in a differential scanning calorimeter followed by melting scans of fractionated PVDF samples to point out the possible presence of a series of endothermic peaks.