Poly(3-hexylthiophene)/gold nanoparticle nanocomposites: relationship between morphology and electrical conductivity

The morphology and electrical properties of gold nanoparticles (AuNP) layer vacuum-deposited onto spin-cast thin films of poly(3-hexylthiophene), P3HT, were studied. The electrical conductivity was measured during temperature cycling and related to the morphology of the same composite structures, which was monitored by transmission electron microscopy (TEM) and extra-high resolution scanning electron microscopy (XHR SEM). Comparison to the analogous polystyrene/AuNP layers was made to distinguish the role of the polymer support on the morphology and electrical properties of the nanoparticles assembly. Gold deposited in a very thin layer formed a nanoparticles-like island structure with the morphology depending on the effective thickness of the deposited layer and on its subsequent thermal treatment. A stabilizing effect of the thiophene–gold interaction on the nanoparticles morphology was observed.     

Gold nanoparticle enhanced charge transfer in thin film assemblies of porphyrin-fullerene dyads

Photoinduced vectorial electron transfer in a molecularly organized porphyrin-fullerene (PF) dyad film is enhanced by the interlayer charge transfer from the porphyrin moiety of the dyad to an octanethiol protected (dcore approximately 2 nm) gold nanoparticle (AuNP) film. By using the time-resolved Maxwell displacement charge (TRMDC) method, the charge separation distance was found to increase by 5 times in a multilayer film structure where the gold nanoparticles face the porphyrin moiety of the dyad, that is, AuNP|PF, compared to the case of the PF layer alone. Films were assembled by the Langmuir-Blodgett (LB) method using octadecylamine (ODA) as the matrix compound. Atomic force microscopy (AFM) images of the monolayers revealed that AuNPs are arranged into continuous, islandlike structures and PF dyads form clusters. The porphyrin reference layer was assembled with the AuNP layer to gain insight on the interaction mechanism between porphyrin and gold nanoparticles. Interlayer electron transfer was also observed between the AuNPs and porphyrin reference, but the efficiency is lower than that in the AuNP|PF film. Fluorescence emission of the reference porphyrin is slightly quenched, and fluorescence decay becomes faster in the presence of AuNPs. The proposed mechanism for the electron transfer in the AuNP|PF film is thus the primary electron transfer from the porphyrin to the fullerene followed by a secondary hole transfer from the porphyrin to the AuNPs, resulting in an increased charge separation distance and enhanced photovoltage.     

Design and photophysical properties of zinc(II) porphyrin-containing dendrons linked to a central artificial special pair

The click chemistry synthesis and photophysical properties, notably photo-induced energy and electron transfers between the central core and the peripheral chromophores of a series of artificial special pair-dendron systems (dendron = G1, G2, G3; Gx = zinc(II) tetra-meso-arylporphyrin-containing polyimides) built upon a central core of dimethylxanthenebis(metal(II) porphyrin) (metal = zinc, copper), are reported. The dendrons act as singlet and triplet energy acceptors or donors, depending on the dendrimeric systems. The presence of the paramagnetic d(9) copper(II) in the dendrimers promotes singlet-triplet energy transfer from the zinc(II) tetra-meso-arylporphyrin to the bis(copper(II) porphyrin) unit and slow triplet-triplet energy transfer from the central bis(copper(II) porphyrin) fragment to the peripheral zinc(II) tetra-meso-arylporphyrin. If bis(zinc(II) porphyrin) is the central core, evidence for chain folding is observed; this is unambiguously demonstrated by the presence of triplet-triplet energy transfer in the heterobimetallic systems, a process that can only occur at short distances.     

Electrochemical behaviors of novel electroactive Au nanoparticles protected by self-assembled monolayers

There has been substantial recent interest in studying monolayer-protected gold clusters (MPCs) owing to their diverse applications. The present work is an electrochemical study of novel gold nanoparticles covered with a monolayer of mercapto-dodecanol ended chloro-dicyano-quinone (HS-C12O-CDQ), which was adsorbed on the electrode (CDQ-MPCs film). Our findings reveal a redox behavior for CDQ-MPCs film similar to the solution electrochemistry of dichloro-dicyano-quinone. Furthermore, a diffusion-like mechanism was found for electron transfer, which may have occurred due to proton diffusion towards or outwards the electrode through the film casted. Chronoamperometry confirmed diffusion behavior of the ET process. Finally, EIS was used to find the rate constant of ET process for the redox reaction that occurred and the contribution of MPCs in total interfacial capacitance.     

Copper phthalocyanine films deposited by liquid-liquid interface recrystallization technique (LLIRCT)

The simple recrystallization process is innovatively used to obtain the nanoparticles of copper phthalocyanine by a simple method. Liquid-liquid interface recrystallization technique (LLIRCT) has been employed successfully to produce small sized copper phthalocyanine nanoparticles with diameter between 3-5 nm. The TEM-SAED studies revealed the formation of 3-5 nm sized with beta-phase dominated mixture of alpha and beta copper phthalocyanine nanoparticles. The XRD, SEM, and the UV-vis studies were further carried out to confirm the formation of copper phthalocyanine thin films. The cyclic voltametry (CV) studies conclude that redox reaction is totally reversible one electron transfer process. The process is attributed to Cu(II)/Cu(I) redox reaction.     

Long Distance Electron Transfer Across >100 nm Thick Au Nanoparticle/Polyion Films to a Surface Redox Protein

Glutathione‐decorated 5 nm gold nanoparticles (AuNPs) and oppositely charged poly(allylamine hydrochloride) (PAH) were assembled into {PAH/AuNP}_n films fabricated layer‐by‐layer (LbL) on pyrolytic graphite (PG) electrodes. These AuNP/polyion films utilized the AuNPs as electron hopping relays to achieve direct electron transfer between underlying electrodes and redox proteins on the outer film surface across unprecedented distances >100 nm for the first time. As film thickness increased, voltammetric peak currents for surface myoglobin (Mb) on these films decreased but the electron transfer rate was relatively constant, consistent with a AuNP‐mediated electron hopping mechanism.     

Direct electron transfer of copper–zinc superoxide dismutase (SOD) on crystallographically oriented Au nanoparticles

The direct electron transfer (ET) of copper–zinc superoxide dismutase (SOD) has been realized, for the first time, at Au nanoparticles electrodeposited onto GC (nano-Au/GC) electrodes. Electrodeposition of Au nanoparticles in the presence of some additive (typically cysteine) resulted in the fabrication of Au nanoparticles with a high roughness morphology (enriched in the Au(1 0 0) orientation) and thus providing a favorable adsorption orientation of SOD (key–lock interaction) suitable for a facilitated direct ET without the use of mediators or so-called ET promoters. The redox reaction of the SOD confined on the nano-Au/GC electrode was found to have a formal potential of +0.02 V vs. Ag/AgCl/KCl(sat). Whereas, round-shape spherical plumbs of Au nanoparticles were electrodeposited in the presence of iodide ions (as additive) which lack for the favorable rough surface and consequently the suitable interaction with the SOD is missing and hence the ET is not realized at this surface.     

Symmetric and asymmetric adsorption of pH-responsive gold nanoparticles onto microgel particles and dispersion characterisation

The interaction between carboxylic acid-stabilised gold nanoparticles (AuNP) and pH-responsive microgels is shown. The microgel particles are a copolymer of N-[3-(dimethylamino)propyl]methacrylamide (DMAPMA) and N-isopropylacrylamide (NIPAM). The microgel properties are presented by their hydrodynamic diameter and electrophoretic mobility in response to pH. These microgel particles are pH-responsive under neutral conditions decreasing in diameter beyond pH 7. The dispersion characteristics of AuNP adsorbed onto the microgel network are shown with respect to adsorbed amount and the pH-responsive properties of the AuNP. This data is presented between pH 3 and 6 where the microgel properties remain constant. Asymmetric adsorption of AuNP onto poly(DMAPMA-co-NIPAM) microgels is achieved by adsorption of nanoparticles, from the aqueous phase, onto microgel-stabilised oil-in-water emulsions. These asymmetrically modified microgels display very different dispersion behaviour, in response to pH, due to their dipolar nature.     

Multimodal coupling of optical transitions and plasmonic oscillations in rhodamine B modified gold nanoparticles

The optical properties of a photoluminescent dye rhodamine B (RhB) interacting with gold nanoparticles (AuNP) have been investigated using plasmonic absorbance, fluorescence, and resonance elastic light scattering (RELS) spectroscopy. We have found that these interactions result in a multimodal coupling that influence optical transitions in RhB. In absorbance measurements, we have observed for the first time the coupling resulting in strong screening of RhB π-π* transitions, likely caused by a contact adsorption of RhB on a conductive surface of AuNP. The nanoparticles quench also very efficiently the RhB fluorescence. We have determined that the static quenching mechanism with a non-F?rster fluorescence resonance energy transfer (FRET) from RhB molecules to AuNP is involved. The Stern-Volmer dependence F(0)/F = f(Q) shows an upward deviation from linearity, attributed to the ultra-high quenching efficiency of AuNP leading to the new extended Stern-Volmer model. A sharp RELS peak of RhB alone (λ(max) = 566 nm) has been observed for the first time and attributed to the resonance fluorescence and enhanced scattering. This peak is completely quenched in the presence of AuNP(22nm). Our quantum mechanical calculations confirm that the distance between AuNP surface and conjugated π-electron system in RhB is well within the range of plasmonic fields extending from AuNP. The optical transition coupling to plasmonic oscillations and the efficient energy transfer due to the interactions of fluorescent dyes with nanoparticles are important for biophysical studies of life processes and applications in nanomedicine.     

Formation of gold nanoparticles using amine reducing agents

We report on the use of amines as reducing agents in the formation of gold nanoparticles. We can predict whether the amines will function as reducing agents in this reaction based on their redox properties. The kinetics of AuNP formation can be understood in terms of Marcus electron transfer theory, where the slower reactions proceed in the inverted region owing to the difference between the Au reduction potential and the amine oxidation potential. For a certain number of the amine reducing agents, following reduction of HAuCl4, a subsequent reaction of the amine radical cation with other reducing agent molecules in solution can form poly(amine)s. These findings point collectively to the utility of amines as reducing agents in AuNP formation and provide information on the conditions under which these reactions will proceed.     

具有温度响应壳层的金纳米粒子的制备

利用可逆-加成断裂链转移聚合得到全亲水性的嵌段共聚物(PEO-b-PNIPAM), 通过"grafting to"使其接枝到金纳米粒子表面. 通过透射电子显微镜、 紫外-可见吸收光谱、 能谱分析及动态光散射研究了杂化的金纳米粒子的壳层结构及温度响应行为. 实验结果表明, 得到核壳结构的金纳米粒子, 同时其壳层具有温度响应行为. 随着温度的升高, 其流体力学半径略有减小. 在整个升温过程中, 由于外层PEO链段的抑制作用, 没有发生粒子间的聚集.     

Effect of Gold Nanoparticles on the Structure and Electron‐Transfer Characteristics of Glucose Oxidase Redox Polyelectrolyte‐Surfactant Complexes

Efficient electrical communication between redox proteins and electrodes is a critical issue in the operation and development of amperometric biosensors. The present study explores the advantages of a nanostructured redox‐active polyelectrolyte–surfactant complex containing [Os(bpy)₂Clpy]²⁺ (bpy=2,2′‐bipyridine, py= pyridine) as the redox centers and gold nanoparticles (AuNPs) as nanodomains for boosting the electron‐transfer propagation throughout the assembled film in the presence of glucose oxidase (GOx). Film structure was characterized by grazing‐incidence small‐angle X‐ray scattering (GISAXS) and atomic force microscopy (AFM), GOx incorporation was followed by surface plasmon resonance (SPR) and quartz‐crystal microbalance with dissipation (QCM‐D), whereas Raman spectroelectrochemistry and electrochemical studies confirmed the ability of the entrapped gold nanoparticles to enhance the electron‐transfer processes between the enzyme and the electrode surface. Our results show that nanocomposite films exhibit five‐fold increase in current response to glucose compared with analogous supramolecular AuNP‐free films. The introduction of colloidal gold promotes drastic mesostructural changes in the film, which in turn leads to a rigid, amorphous interfacial architecture where nanoparticles, redox centers, and GOx remain in close proximity, thus improving the electron‐transfer process.     

Improved separation and size characterization of gold nanoparticles through a novel capillary zone electrophoresis method using poly(sodium4‐styrenesulfonate) as stabiliser and a stepwise field strength gradient

A novel capillary zone electrophoresis (CZE) method was developed for an improved separation and size characterization of pristine gold nanoparticles (AuNP) using uncoated fused‐silica capillaries with UV‐Vis detection at 520 nm. To avoid colloid aggregation and/or adsorption during runs, poly(sodium 4‐styrenesulfonate) (PSS) was added (1%, w/v) in the running buffer (CAPS 10 mM, pH 11). This polyelectrolyte conferred an enhanced stabilization to AuNP, both steric and electrostatic, exalting at the same time their differences in electrophoretic mobility. Resolution was further and successfully improved through a stepwise field strength gradient by the application of 25 kV for the first 5 min and then 10 kV. Migration times varied linearly with particles diameters showing relative standard deviations better than 1% for daily experiments and 3% for interday experiments. A comparison with the size distribution obtained by transmission electron microscopy (TEM) allowed assessing that the electrophoretic profile can reasonably be considered as representative of the effective size heterogeneity of each colloid. Finally, the practical utility of the proposed method was demonstrated by measuring the core diameter of a gold colloid sample produced by chemical synthesis which was in good agreement with the value obtained by TEM measurements.     

A non-aqueous organometallic route to highly monodispersed copper nanoparticles using [Cu(OCH(Me)CH2NMe2)2

Good quality, highly monodispersed capped copper metal nanoparticles have been synthesised in a non-hydrolytic approach using thermal decomposition of the Cu(II) precursor [Cu(OCH(Me)CH2NMe2)2] in a hot coordinating solvent without further reducing agents; the copper nanoparticles have been characterised by optical spectroscopy (UV/VIS), electron microscopy (TEM), electron diffraction (SAED), and dynamic light scattering (DLS).     

Modeling and computations of the intramolecular electron transfer process in the two-heme protein cytochrome c(4)

The di-heme protein Pseudomonas stutzeri cytochrome c(4) (cyt c(4)) has emerged as a useful model for studying long-range protein electron transfer (ET). Recent experimental observations have shown a dramatically different pattern of intramolecular ET between the two heme groups in different local environments. Intramolecular ET in homogeneous solution is too slow (>10 s) to be detected but fast (ms-μs) intramolecular ET in an electrochemical environment has recently been achieved by controlling the molecular orientation of the protein assembled on a gold electrode surface. In this work we have performed computational modeling of the intramolecular ET process by a combination of density functional theory (DFT) and quantum mechanical charge transfer theory to disclose reasons for this difference. We first address the electronic structures of the model heme core with histidine and methionine axial ligands in both low- and high-spin states by structure-optimized DFT. The computations enable estimating the intramolecular reorganization energy of the ET process for different combinations of low- and high-spin heme couples. Environmental reorganization free energies, work terms ("gating") and driving force were determined using dielectric continuum models. We then calculated the electronic transmission coefficient of the intramolecular ET rate using perturbation theory combined with the electronic wave functions determined by the DFT calculations for different heme group orientations and Fe-Fe separations. The reactivity of low- and high-spin heme groups was notably different. The ET rate is exceedingly low for the crystallographic equilibrium orientation but increases by several orders of magnitude for thermally accessible non-equilibrium configurations. Deprotonation of the propionate carboxyl group was also found to enhance the ET rate significantly. The results are discussed in relation to the observed surface immobilization effect and support the notion of conformationally gated ET.     

Ligand Control over the Electronic Properties within the Metallic Core of Gold Nanoparticles

The behavior of electrons within the metallic core of gold nanoparticles (AuNPs) can be controlled by the nature of the surface chemistry of the AuNPs. Specifically, the conduction electron spin resonance (CESR) spectra of AuNPs of diameter 1.8–1.9 nm are sensitive to ligand exchange of hexanethiol for 4‐bromothiophenol on the surface of the nanoparticle. Chemisorption of the aromatic ligand leads to a shift in the metallic electron’s g‐factor toward the value expected for pure gold systems, suggesting an increase in metallic character for the electrons within the gold core. Analysis by UV/Vis absorption spectroscopy reveals a concomitant bathochromic shift of the surface plasmon resonance band of the AuNP, indicating that other electronic properties of AuNPs are also affected by the ligand exchange. In total, our results demonstrate that the chemical nature of the ligand controls the valence band structure of AuNPs.     

纳米晶体自组装结构中非辐射能量传递过程的验证

以上转换纳米粒子NaYF₄：20% Yb,2% Er@NaYF₄（标记为UCNP）和金纳米粒子（AuNP）分别作为能量传递研究的给体和受体,研究在具有确定位置关系的组装结构中二者之间的非辐射能量传递是否存在。以UCNP和AuNP作为基本构建单元,采用气-液界面溶剂挥发法,得到了连续大面积规整排列的二维UCNP单层自组装膜。再通过层层组装得到UCNP+AuNP双层膜、UCNP+NaYF₄+AuNP三层膜。利用自行搭建的光谱成像系统对自组装结构进行了发光性质测试。对比3种膜结构的发光情况,发现UCNP+AuNP双层膜和UCNP+NaYF₄+AuNP三层膜的发光与UCNP单层膜减弱幅度相近,即在我们研究的体系中UCNP和AuNP之间不存在明显的非辐射能量传递过程。本研究提供了一种几何关系明确的组装体模型,并搭建了相应的微区发光性质测试设备,验证了在我们设计的自组装模型中并不存在UCNP与AuNP的非辐射能量传递。     

Polystyrene‐Core–Silica‐Shell Hybrid Particles Containing Gold and Magnetic Nanoparticles

Polystyrene‐core–silica‐shell hybrid particles were synthesized by combining the self‐assembly of nanoparticles and the polymer with a silica coating strategy. The core–shell hybrid particles are composed of gold‐nanoparticle‐decorated polystyrene (PS‐AuNP) colloids as the core and silica particles as the shell. PS‐AuNP colloids were generated by the self‐assembly of the PS‐grafted AuNPs. The silica coating improved the thermal stability and dispersibility of the AuNPs. By removing the “free” PS of the core, hollow particles with a hydrophobic cage having a AuNP corona and an inert silica shell were obtained. Also, Fe₃O₄ nanoparticles were encapsulated in the core, which resulted in magnetic core–shell hybrid particles by the same strategy. These particles have potential applications in biomolecular separation and high‐temperature catalysis and as nanoreactors.     

Spatially controlled SERS patterning using photoinduced disassembly of gelated gold nanoparticle aggregates

Controlling the assembly of the nanoparticles is important because the optical properties of noble metal nanoparticles, such as the surface plasmon resonance (SPR) and surface-enhanced Raman scattering (SERS), are critically dependent on interparticle distances. Among many approaches available, light-induced disassembly is particularly attractive because it enables spatial modification of the optical properties of nanoparticle assemblies. In this study, we prepare gold nanoparticle (AuNP) aggregates in a gel matrix. Irradiation of the gelated AuNP aggregates at 532 nm leads to the disassembly of the aggregates, changing the color (SPR) from dark blue to red and extinguishing the SERS signal along the irradiated pattern, which opens the possibility of facile fabrication of spatially controlled SERS-generating microstructures. The photoinduced disassembly of the AuNP aggregates in solution is also investigated using UV-vis spectroscopy and transmission electron microscopy.     

Photoinduced electron transfer between chlorophyll a and gold nanoparticles

Excited-state interactions between chlorophyll a (Chla) and gold nanoparticles have been studied. The emission intensity of Chla is quenched by gold nanoparticles. The dominant process for this quenching has been attributed to the process of photoinduced electron transfer from excited Chla to gold nanoparticles, although because of a small overlap between fluorescence of Chla and absorption of gold nanoparticles, the energy-transfer process cannot be ruled out. Photoinduced electron-transfer mechanism is supported by the electrochemical modulation of fluorescence of Chla. In absence of an applied bias, Chla cast on gold film, as a result of electron transfer, exhibits a very weak fluorescence. However, upon negatively charging the gold nanocore by external bias, an increase in fluorescence intensity is observed. The negatively charged gold nanoparticles create a barrier and suppress the electron-transfer process from excited Chla to gold nanoparticles, resulting in an increase in radiative process. Nanosecond laser flash experiments of Chla in the presence of gold nanoparticles and fullerene (C60) have demonstrated that Au nanoparticles, besides accepting electrons, can also mediate or shuttle electrons to another acceptor. Taking advantage of these properties of gold nanoparticles, a photoelectrochemical cell based on Chla and gold nanoparticles is constructed. A superior performance of this cell compared to that without the gold film is due to the beneficial role of gold nanoparticles in accepting and shuttling the photogenerated electrons in Chla to the collecting electrode, leading to an enhancement in charge separation efficiency.