Magnetic and microwave absorption properties of BaFe12−x (Mn0.5Cu0.5Zr)x/2O19 synthesized by sol–gel processing

BaFe_12−x (Mn_0.5Cu_0.5Zr)_x/2O₁₉ hexaferrites with x=1, 2 and 3 were prepared by sol–gel process. The ferrite powders possess hexagonal shape and are well separated from one another. The powders of these ferrites were mixed with polyvinylchloride (PVC) plasticizer to be converted into a microwave absorbing composite ferrite with a thickness of 1.8 mm. X-ray diffractometer (XRD), scanning electron microscope (SEM), ac susceptometer, vibrating sample magnetometer and vector network analyzer were used to analyze its structure, electromagnetic and microwave absorption properties. The results showed that magnetoplumbite structures for all samples were formed. The sample with higher magnetic susceptibility and coercivity exhibits a larger microwave absorbing ability. Also the present investigation demonstrates that a microwave absorber using BaFe_12−x(Mn_0.5Cu_0.5Zr)_x/2O₁₉ (x=2 and 3)/PVC with a matching thickness of 1.8 mm can be fabricated for applications over 15 GHz, with reflection loss more than −25 dB for specific frequencies, by controlling the molar ratio of the substituted ions.     

Influence of Cr content on structure and magnetic properties of Fe-Si-Al-Cr powders

As a kind of soft magnetic metallic material, flaky FeSiAl powders have been studied and used widely. Transition metal chromium can improve the magnetic properties of FeSiAl. This article prepared Fe₈₅Si_9.5-xAl_5.5Cr_x (x=0, 2, 4, 6 wt%) alloys powders by adding chromium to replace silicon in alloys. The morphology and microstructure of alloys powders were studied, electromagnetic parameters were measured and microwave absorption properties in the frequency range from 0.5 to 18 GHz were analyzed. With the increase of Cr content, α-Fe (Al, Si) superlattice phases appeared in alloys powders, and then disappeared. Excessive Cr precipitated from the alloys when its content reaches 6 wt%. The minimum reflection loss (-20 dB) among the four powders was 2 wt% Cr content at the frequency of 11.5 GHz. The peaks of reflection loss shifted to the low frequency range with increase in Cr content.     

Structural and magnetic properties of sol-gel Co2xNi0.5−x Zn0.5−xFe2O4 thin films

Nanocrystalline Co_2xNi_0.5−xZn_0.5−xFe₂O₄ (x=0−0.5) thin films have been synthesized with various grain sizes by a sol-gel method on polycrystalline silicon substrates. The morphology as well as magnetic and microwave absorption properties of the films calcined at 1073 K were studied using X-ray diffraction, scanning electron microscopy, X-ray photoelectron spectroscopy, and vibrating sample magnetometry. All films were uniform without microcracks. The Co content in the Co-Ni-Zn films resulted in a grain size ranging from 15 to 32 nm while it ranged from 33 to 49 nm in the corresponding powders. Saturation and remnant magnetization increased with increase in grain size, while coercivity demonstrated a drop due to multidomain behavior of crystallites for a given value of x. Saturation magnetization increased and remnant magnetization had a maximum as a function of grain size independent of x. In turn, coercivity increased with x independent of grain size. Complex permittivity of the Co-Ni-Zn ferrite films was measured in the frequency range 2-15 GHz. The highest hysteretic heating rate in the temperature range 315-355 K was observed in CoFe₂O₄. The maximum absorption band shifted from 13 to 11 GHz as cobalt content increased from x=0.1 to 0.2.     

Electromagnetic properties and microwave absorbing characteristics of doped barium hexaferrite

M-type barium hexaferrite BaFe_12−x(Mn_0.5Cu_0.5Ti)_x/2O₁₉ (x varying from 0 to 3 in steps of 1) have been synthesized by the usual ceramic sintering method. The ferrite powders possess hexagonal shape and are well separated from one another. The powder of these ferrites were mixed with polyvinylchloride plasticizer to be converted in to a microwave absorbing composite. X-ray diffraction (XRD), scanning electron microscope (SEM), ac susceptometer, vibrating sample magnetometer, and vector network analyzer were used to analyze its structure, electromagnetic and microwave absorption properties. The results showed that, the magnetoplumbite structures for all the samples have been formed. The sample having higher magnetic susceptibility and coercivity exhibits a larger microwave absorbing ability. Also, the present investigation demonstrates that microwave absorber using BaFe_12−x (Mn_0.5Cu_0.5Ti)_x/2O₁₉ (x=2$x=2$ and 3)/polyvinylchloride can be fabricated for the applications over 15 GHz, with reflection loss more than −25 dB for specific frequencies, by controlling the molar ratio of the substituted ions.     

Zn- and Cu-substituted Co2Y hexagonal ferrites: Sintering behavior and permeability

Y-type polycrystalline hexagonal ferrites Ba₂Co_2−x−yZn_xCu_yFe₁₂O₂₂ with 0≤x≤2 and 0≤y≤0.8 were prepared by the mixed-oxide route. Single phase Y-type ferrite powders were obtained after calcinations at 1000 °C. Samples sintered at 1200 °C show a permeability that increases with the substitution of Zn for Co and display maximum permeability of μ′=35 at 1 MHz for x=1.6 and y=0.4. A resonance frequency f_r=500 MHz is observed for Zn-rich ferrites with y=0 and 0.4. The saturation magnetization increases with substitution of Zn for Co. Addition of Bi₂O₃ shifts the temperature of maximum shrinkage down to T≤950 °C. Moreover, an increase of the Cu-concentration further lowers the sintering temperature to T≤900 °C, enabling co-firing of the ferrites with Ag metallization for multilayer technologies. However, low-temperature firing reduces the permeability to μ′=10 and the resonance frequency is shifted to 1 GHz. Thus substituted hexagonal Y-type ferrites can be used as soft magnetic materials for multilayer inductors for high frequency applications.     

Influence of manganese substitution and annealing temperature on the formation,microstructure and magnetic properties of Mn–Zn ferrites

The effects of annealing temperature and manganese substitution on the formation, microstructure and magnetic properties of Mn_xZn_1−xFe₂O₄ (with x varying from 0.3 to 0.9) through a solid-state method have been investigated. The correlation of the microstructure and the grain size with the magnetic properties of Mn–Zn ferrite powders was also reported. X-ray diffraction (XRD), a scanning electron microscope (SEM) and a vibrating sample magnetometer (VSM) were utilized in order to study the effect of variation of manganese substitution and its impact on crystal structure, crystalline size, microstructure and magnetic properties of the ferrite powders formed. The XRD analysis showed that pure single phases of Mn–Zn ferrites were obtained by increasing the annealing temperature to 1200–1300 °C. Increasing the annealing temperature to ?1300 °C led to abnormal grain growth with inter-granular pores and this led to a decrease in the saturation magnetization. Moreover, an increase in the Mn²⁺ ion substitution up to x=0.8 increased the lattice parameter of the formed powders due to the high ionic radii of the Mn²⁺ ion. Mn–Zn ferrites phases were formed and the positions of peaks were shifted by substituting manganese. The average crystalline size was increased by increasing the annealing temperature and decreased by increasing the substitution by manganese up to 0.8. The average crystalline size was in the range 95–137.3 nm. The saturation magnetization of the Mn–Zn-substituted ferrite powders increased continuously with an increase in the Mn concentration up to 0.8 at annealing temperatures of 1200–1300 °C. Further increase of Mn substitution up to 0.9 led to a decrease of saturation magnetization. The saturation magnetization increased from 17.3 emu/g for the Mn_0.3Zn_0.7Fe₂O₄ phase particles produced to 59.08 emu/g for Mn_0.8Mn_0.2Fe₂O₄ particles.     

Electromagnetic properties of samarium-substituted NiCuZn ferrite prepared by auto-combustion method

Ni_0.25Cu_0.2Zn_0.55Sm_xFe_2−xO₄ ferrite with x=0.00, 0.025, 0.05 and 0.075 compositions were synthesized through the nitrate-citrate auto-combustion method. These powders were calcined, compacted and sintered at 900 °C for 4 h. Effect of Sm substitution on phase composition, microstructure and relative density were studied. Permeability, magnetic loss and AC resistivity were measured in the frequency range of 1 kHz-10 MHz. Permeability and AC resistivity were found to increase and loss decreased with Sm substitution up to x=0.05. Saturation magnetization also increased up to that substitution limit. Observed variations in electromagnetic properties have been explained.     

Structural and magnetic properties of MnxCo1−xFe2O4 ferrite nanoparticles

We report on the structural and magnetic properties of nanoparticles of Mn_xCo_1−xFe₂O₄ (x=0.1, 0.5) ferrites produced by the glycothermal reaction. From the analysis of XRD spectra and TEM micrographs, particle sizes of the samples have been found to be about 8 nm (for x=0.1) and 13 nm (for x=0.5). The samples were characterized by DC magnetization in the temperature range 5-380 K and in magnetic fields of up to 40 kOe using a SQUID magnetometer. Mössbauer spectroscopy results show that the sample with higher Mn content has enhanced hyperfine fields after thermal annealing at 700 °C. There is a corresponding small reduction in hyperfine fields for the sample with lower Mn content. The variations of saturation magnetization, remnant magnetization and coercive fields as functions of temperature are also presented. Our results show evidence of superparamagnetic behaviour associated with the nanosized particles. Particle sizes appear to be critical in explaining the observed properties.     

Electromagnetic properties of manganese-zinc ferrite with lithium substitution

Polycrystalline manganese-zinc ferrite with lithium substitution of composition Li_0.5xMn_0.4Zn_0.6−xFe_2+0.5xO₄ (0.0≤x≤0.4) was prepared by the usual ceramic method. X-ray diffraction analysis confirmed that the samples have a spinel structure and are of single phase for some values of Li content. Lithium doping considerably modifies saturation magnetization since its value increases from 57.5 emu/g for x=0.0 to 82.9 emu/g for x=0.4. Lithium inclusion increases the real permeability (over 1 MHz) while the natural resonance frequency shifts to lower values as the fraction of Li increases. These ferrites show good electromagnetic properties as absorbers in the microwave range of 1 MHz - 1 GHz.     

The effect of multi-step milling and annealing treatments on microstructure and magnetic properties of nanostructured Fe-Si powders

Nanostructured Fe_1−xSi_x (x=0.05, 0.1, 0.15 and 0.2) powders are prepared by different multi-step milling and annealing treatments. The microstructure and magnetic properties are investigated for all alloys. The minimum crystallite size of as-annealed powders (∼40 nm) is found to be larger than in as-milled ones (∼15 nm). It is found that microstrains of 2- and 4-step processes are close to those of the as-received powders. The lattice parameter decreased ∼0.5% and 0.9% for the powders that experienced milling and annealing at the last step, respectively. The Fe₈₀Si₂₀ powders prepared by 1- and 4-step treatments show the maximum (40-125 Oe) and minimum (20-26 Oe) coercivity, respectively. With increase in milling time, mass magnetization increased for all processes. This can be ascribed to diminution in magneto-crystalline anisotropy due to grain refinement. The maximum mass magnetization (160-199 Am²/kg) is achieved for the 4-step process.     

Effects of In-substitution on the structure and magnetic properties of multi-doped YIG ferrites with low saturation magnetizations

Multi-doped YIG ferrites {Y_1.7Gd_0.5Ca_0.8}[Fe_2−xIn_x](Fe_2.15V_0.4Mn_0.05Al_0.4)O₁₂ (x=0, 0.3, 0.6, 0.7, 0.8 and 0.9) with low saturation magnetizations (4πM_s=400-600 G at 298 K) were prepared by a conventional ceramic technology and the effects of In³⁺-substitution on their structures and magnetic properties were systematically investigated using XRD, SEM and VSM. It has been found that as-synthesized powders and sintered ferrites showed a single-phase of garnet structure with a cell parameter (a) that increased linearly with increase in In³⁺ concentration from x=0 up to 0.9. Apparent relative densities of sintered samples were all over 98%, but no remarkable influences of In³⁺-substitution were observed by SEM on the refinement of crystal grains and the enhancement of sintering of ferrites. In addition, the Curie temperature T_c decreased almost linearly as In³⁺concentration increased, while the corresponding saturation magnetization at room temperature presented a variation characterized by a gradual increase first and then a rapid plunge. On the basis of quantitative analysis of XRD data and the theory on super-exchange interactions, it has been established that the incorporated In³⁺ ions via doping were exclusively located at the sites with octahedral coordinations in the crystal structure and the aforementioned magnetic properties can be simply attributed to weakening super-exchange interactions between neighboring magnetic ions through oxygen ions due to the “dilution effect” of added non-magnetic In³⁺ ions.     

Heat treatment effects on microstructure and magnetic properties of Mn-Zn ferrite powders

Mn-Zn ferrite powders (Mn_0.5Zn_0.5Fe₂O₄) were prepared by the nitrate-citrate auto-combustion method and subsequently annealed in air or argon. The effects of heat treatment temperature on crystalline phases formation, microstructure and magnetic properties of Mn-Zn ferrite were investigated by X-ray diffraction, thermogravimetric and differential thermal analysis, scanning electron microscopy and vibrating sample magnetometer. Ferrites decomposed to Fe₂O₃ and Mn₂O₃ after annealing above 550 °C in air, and had poor magnetic properties. However, Fe₂O₃ and Mn₂O₃ were dissolved after ferrites annealing above 1100 °C. Moreover, the 1200 °C annealed sample showed pure ferrite phase, larger saturation magnetization (M_s=48.15 emu g⁻¹) and lower coercivity (H_c=51 Oe) compared with the auto-combusted ferrite powder (M_s=44.32 emu g⁻¹, H_c=70 Oe). The 600 °C air annealed sample had the largest saturation magnetization (M_s=56.37 emu g⁻¹) and the lowest coercivity (H_c=32 Oe) due to the presence of pure ferrite spinel phase, its microstructure and crystalline size.     

Preparation and magnetic properties of La-substituted Zn–Cu–Cr ferrites via a rheological phase reaction method

Nanocrystalline La-substituted Zn–Cu–Cr ferrites Zn_0.6Cu_0.4Cr_0.5La_xFe_1.5−xO₄ (x=0.00, 0.02, 0.04, 0.06) were prepared by a rheological phase reaction method. The obtained powders were characterized by X-ray diffractometer, transmission electron microscopy and vibrating sample magnetometer. Permeability of the samples was investigated using an impedance analyzer. The results indicated that ferrite samples had the single spinel phase at low La content. Lattice parameter increased with increasing La content, while particle size calculated from Scherrer's formula decreased with increasing La content in La-substituted ferrite samples. The magnetic properties of La-substituted ferrites were strongly affected by La content. The saturation magnetization decreased, while coercivity increased with increasing La content. The variation of real permeability with La content was investigated in the frequency range of 1 MHz–1 GHz.     

Synthesis and characterization of Sr(ZnZr)x Fe12−2xO19-PANI composites

Strontium zinc zirconium hexaferrites/polyaniline (Sr(ZnZr)_xFe_12−2xO₁₉-PANI, x=0, 0.5, 1.0) composites were synthesized by oxidative chemical polymerization of aniline in the presence of ammonium peroxydisulfate (APS). The structure and morphology of the product was characterized by FTIR, TGA and SEM. The particle size of the core material was found to be about 250-500 nm. After coating with polyaniline, the particle size of Sr(ZnZr)_0.5Fe₁₁O₁₉-PANI composites grew upto 0.5-1.0 μm. XRD of the ferrites indicated that the structure of the core materials is hexagonal, with lattice constants around 5.886-5.885 Å. It was found that the saturation magnetization (M_S) and coercivity (H_C) for Sr(ZnZr)_xFe_12−2xO₁₉-PANI composites decreased after polyaniline coating. The composite under applied magnetic field, exhibited ferromagnetic hysteretic loops with high saturation magnetization (M_S=18.9-3.8 emu/g) and coercivity (H_C=3850.0-583.91 Oe).     

Structure and properties of (AlCrMnMoNiZrB0.1)Nx coatings prepared by reactive DC sputtering

The microstructure and properties of AlCrMnMoNiZrB_0.1 nitride films prepared by reactive direct current sputtering at various N₂-to-Ar flow ratios (R_N) were investigated. The films had an amorphous structure at low R_N and a face-centered cubic structure at a high R_N. As the R_N increased, the decrease in clusters and defects resulted in a dense columnar structure and low surface roughness. The peak hardness and modulus of the nitride films were 10.3 and 180 GPa, respectively. The enhanced hardness is ascribed to the increased metal-nitrogen bonding, solid solution strengthening of several metallic nitrides, and lattice strain. The nitride films deposited at R_N = 0.2, 0.5, and 0.8 had friction coefficients of 0.16, 0.12 and 0.15, respectively. Wear-out failure occurred within 400 s when R_N = 0 and 1.0. Adhesive wear was the dominant wear mechanism.     

Role of vanadium content in ZnO thin films grown by pulsed laser deposition

Vanadium-doped ZnO films (Zn_1−xV_xO, where x = 0.02, 0.03, 0.05 and 0.07), were formed from ceramic targets on c-cut sapphire substrates using pulsed laser deposition at substrate temperature of 600 °C and oxygen pressure of 10 Pa. In order to clarify how the vanadium concentration influences the films’ properties, structural and magnetic investigations were performed. All films crystallised in wurtzite phase and presented a c-axis preferred orientation at low concentrations of vanadium. The results implied that the doping concentration and crystalline microstructure influence strongly the system's magnetic characteristics. Weak ferromagnetism was registered for the film with the lowest doping concentration (2 at.%), which exhibited a ferromagnetic behavior at Curie temperature higher than 300 K. Increasing the vanadium content in the film caused degradation of the magnetic ordering.     

Study on electro-magnetic properties of La substituted Ni–Cu–Zn ferrite synthesized by auto-combustion method

(Ni_0.25Cu_0.20Zn_0.55)La_xFe_2−xO₄ ferrite with x=0.00, 0.025, 0.050 and 0.075 compositions were synthesized through nitrate–citrate auto-combustion method. Crystalline spinel ferrite phase with about 16–19 nm crystallite size was present in the as-burnt ferrite powder. These powders were calcined, compacted and sintered at 950 °C for 4 h. Initial permeability, magnetic loss and AC resistivity of different compositions were measured in the frequency range from 10 Hz to 10 MHz. Saturation magnetization and hysteresis parameters were measured at room temperature with a maximum magnetic field of 10 kOe. Permeability and AC resistivity were found to increase and magnetic loss decreased with La substitution for Fe, up to x=0.025. Saturation magnetization and coercive field also increases up to that limit. The electromagnetic properties were found best in the ferrite composition of x=0.025, which would be better for more miniaturized multi layer chip inductor.     

Electromagnetic properties of lithium zinc ferrites doped with aluminum

We present the results of the effect of Al substitution on the magnetic and electrical properties of Li_0.2Zn_0.6Fe_2.2−xAl_xO₄ ferrites (0.0≤x≤0.5) prepared by the standard ceramic technique. The characterization has been performed using XRD, SEM, magnetic and dielectric response in frequency. XRD analysis confirms that the system exhibits polycrystalline single phase cubic spinel structure only for low dopant content. Doping decreases the dielectric loss tangent and the ferrite conductivity in more than two orders of magnitude in the whole analyzed frequency range. Attenuation has a maximum intensity (86 dB) near 90 MHz for x=0.4. The wider bandwidth at 20 dB (94.6 MHz) is for x=0.3.     

Crystallization and annealing effects of sputtered tin alloy films on electromagnetic interference shielding

Sn, Al and Cu not only possess electromagnetic interference (EMI) shield efficiency, but also have acceptable costs. In this study, sputtered Sn-Al thin films and Sn-Cu thin films were used to investigate the effect of the crystallization mechanism and film thickness on the electromagnetic interference (EMI) characteristics. The results show that Sn-xAl film increased the electromagnetic interference (EMI) shielding after annealing. For as-sputtered Sn-xCu films with higher Cu atomic concentration, the low frequency EMI shielding could not be improved. After annealing, the Sn-Cu thin film with lower Cu content possessed excellent EMI shielding at lower frequencies, but had an inverse tendency at higher frequencies. For both the Sn-xAl and Sn-xCu thin films after crystallization treatment, the sputtered films had higher electrical conductivity, however the EMI shielding was not enhanced significantly.     

Effect of magnesium substitution on dielectric and magnetic properties of Ni-Zn ferrite

The dielectric and magnetic properties of Mg incorporated Ni-Zn spinel ferrites have been investigated. Ni_0.5−xZn_0.5Mg_xFe₂O₄ ferrites have been prepared by sol-gel auto-combustion technique. The as prepared ferrites were annealed at 673, 873 and 1073 K. The X-ray diffraction studies reveal the spinel structure of annealed ferrites. The TEM results are in agreement with XRD results. FTIR study has also been carried out to get insight into the structure of these ferrites. The dielectric measurements show that the dielectric constant (ε′), dielectric loss (tan δ) and conductivity (σ_ac) increase on incorporation of Mg in the Ni-Zn ferrite. ε′, tan δ and σ_ac also show dependence on temperature, frequency of external applied electric field and microstructure of the samples. The magnetic moment measurements reveal that the saturation magnetization (M_s) increases and coercivity (H_c) decreases with the increase in concentration of Mg²⁺ ions. M_s and H_c also show dependence on the annealing temperature.