EPR study of Mn-implanted single crystal plates of TiO2 rutile

Single crystals of Mn-implanted TiO₂ rutile have been investigated by electron paramagnetic resonance (EPR) technique at room temperature. We have observed an EPR signal on Mn⁴⁺ ions (S=) in the manganese-implanted single crystal TiO₂ plates. Besides, weaker EPR signals due to Fe³⁺(S=, L=0) and Cr³⁺(S=) ions have also been observed. Characteristic six-line splitting of the manganese EPR lines due to hyper-fine interaction with ⁵⁵Mn nuclei (spin I=) has also been observed. Analysis of the EPR spectra shows that the manganese, iron and chromium ions substitute for Ti⁴⁺ ions in the TiO₂ rutile host. Two structurally equivalent groups of the centers have been observed in the EPR spectra in correspondence with two octahedral positions of the Ti ions in the rutile structure. Spin Hamiltonian parameters for the crystal field of orthorhombic symmetry on the Mn⁴⁺, Fe³⁺ and Cr³⁺ centers have been obtained as result of computer modelling.     

From anodic TiO2 nanotubes to hexagonally ordered TiO2 nanocolumns

We report on the formation of hexagonally ordered TiO₂ nanocolumnar layers by electrochemical oxidation in a fluoride containing electrolyte, using self-organizing nanotube formation conditions at elevated potentials and low temperatures. The influence of the substrate temperature on the nanocolumn morphology and composition is investigated and characterized by FE-SEM and EDX. The origin of these nanocolumns can be attributed to a thickening of the inner tube wall of the double wall structure of self-organized TiO₂ nanotubes. Furthermore, a transition from nanocolumnar to nanotubular structure can be established by changing the applied voltage or applying a post-immersion treatment.     

钴离子注入对二氧化钛晶体的结构和光学性能的影响

采用离子注入法制备了钴离子掺杂的金红石相TiO₂样品;离子注入能量、注量分别为40 keV(1×10¹⁶cm^-2),80 keV(5×10¹⁵,1×10¹⁶,5×10¹⁶,1×10¹⁷cm^-2),120 keV(1×10¹⁶cm^-2). 通过XRD,XPS和UV-Vis等手段对掺杂前后样品的结构和光学性能进行了表征,分析了掺杂元素在金红石TiO₂中的存在形式. XRD测试表明随着注入能量的增加晶体的损伤程度增加. UV-Vis测试表明掺杂后所有样品在可见光区的吸收增强; 并且随着注量的增加,注量为5×10¹⁵cm^-2到5×10¹⁶cm^-2范围内注入样品的光学带隙逐渐变小. 关键词： 钴 二氧化钛 离子注入 掺杂     

特定位点上CO2与(TiO2)n团簇相互作用的第一性原理研究

本文基于密度泛函理论系统地研究了(TiO₂)_n团簇上二氧化碳(CO₂)的吸附和活化性质. 计算结果表明,CO₂更倾向于吸附在(TiO₂)_n团簇的桥氧原子上,形成“化学吸附”碳酸盐络合物. 而CO更倾向于吸附到末端Ti-O的Ti原子上. 发现计算得到的碳酸盐振动频率值与实验获得的结果非常吻合,这表明配合物中CO₂的几何构型与其线性型相比,有微小的弯转. 通过对电子结构、电荷密度、电离势、HOMO-LUMO以及态密度的分析,证实了CO₂与团簇之间的电荷转移以及相互作用. 从预测的能量分布图来看,(TiO₂)_n团簇上的CO₂活化与结构密切有关,相比于块体的TiO₂,CO₂在团簇结构上更易于吸附和活化.     

The enhanced photocatalytic activity of CdS/TiO2 nanocomposites by controlling CdS dispersion on TiO2 nanotubes

CdS/TiO₂ nanocomposites were prepared via a simple wet chemical method, and characterized through X-ray diffraction (XRD) and transmission electron microscopy (TEM). Their ability to degrade Acid Rhodamine B was investigated under visible light irradiation. The results indicate that CdS/TiO₂ nanocomposite with a mass ratio of 4:1(TiO₂:CdS) showed high photocatalytic activity and the CdS loaded on TiO₂ nanotube surface exhibited a hexagonal phase. The dispersion of CdS on TiO₂ nanotube surface had an important effect on the degradation efficiency of pollutant, which provides a strategy for practical industry application.     

Synthesis, structure and optical properties of Eu/TiO2 nanocrystals at room temperature

The nanocrystal samples of titanium dioxide doped with europium ion (Eu³⁺/TiO₂ nanocrystal) are synthesized by the sol-gel method with hydrothermal treatment. The Eu³⁺ contents (molar ratio) in the samples are 0, 0.5%, 1%, 2%, 3% and 4%. The X-ray diffraction, UV-Vis spectroscopy data and scanning electron microscope image show that crystallite size is reduced by the doping of Eu³⁺ into TiO₂. Comparing the Raman spectra of TiO₂ with Eu³⁺/TiO₂ (molar ratio Eu³⁺/TiO₂=1%, 2% and 4%) nanocrystals at different annealing temperatures indicates that the anatase-to-rutile phase transformation temperatures of Eu³⁺/TiO₂ nanocrystals are higher than that of TiO₂. This is due to the formation of Eu-O-Ti bonds on the surface of the TiO₂ crystallite, as characterized by the X-ray photoelectron spectroscopy. The photoluminescence spectra of TiO₂ in Eu³⁺/TiO₂ nanocrystals are interpreted by the surface self-trapped and defect-trapped exciton relaxation. The photoluminescence of Eu³⁺ in Eu³⁺/TiO₂ nanocrystals has the strongest emission intensity at 2% of Eu³⁺ concentration.     

Preparation and characterization of amine-functionalized SiO2/TiO2 films for formaldehyde degradation

This paper investigated the gaseous formaldehyde degradation by the amine-functionalized SiO₂/TiO₂ photocatalytic films for improving indoor air quality. The films were synthesized via the co-condensation reaction of methyltrimethoxysilane (MTMOS) and 3-aminopropyltrimethoxysilane (APTMS). The physicochemical properties of prepared photocatalysts were characterized with N₂ adsorption/desorption isotherms measurement, X-ray diffraction (XRD) and Fourier Transform Infrared spectroscopy (FT/IR). The effect of amine-functional groups and the ratio of MTMOS/APTMS precursors on the formaldehyde adsorption and photocatalytic degradation were investigated. The results showed that the formaldehyde adsorption and photocatalytic degradation of the APTMS-functionalized SiO₂/TiO₂ film was higher than that of SiO₂/TiO₂ film due to the surface adsorption on amine sites and the relatively high of the specific surface area of the APTMS-functionalized SiO₂/TiO₂ film (15 times higher than SiO₂/TiO₂). The enhancement of the formaldehyde degradation of the film can be attributed to the synergetic effect of adsorption and subsequent photocatalytic decomposition. The repeatability of photocatalytic film was also tested and the degradation efficiency was 91.0% of initial efficiency after seven cycles.     

Photoelectrocatalytic degradation of organic contaminants at Bi2O3/TiO2 nanotube array electrode

In the current work, TiO₂ nanotube array was prepared via electrochemical anode method. Then the Bi₂O₃ nanoparticles were deposited onto the TiO₂ nanotube array via dip-coating method from an amorphous complex precursor. The crystal structures were characterized via X-ray diffraction analysis. Their surface textures were observed via electron-scanning microscope. The prepared composite array electrode exhibited high photoelectrocatalytic activities towards degrading organic contaminants under visible light irradiation. High photoelectrocatalytic activities were also exhibited under UV light irradiation. The catalytic mechanism was discussed based on the analysis of electrochemical and degradation kinetics results. It is suggested a P (Bi₂O₃)-N (TiO₂) junction was formed to increase the catalytic activates. The stability of the electrode materials was confirmed finally.     

N掺杂锐钛矿TiO2电子结构的第一性原理研究

为了研究N掺杂对锐钛矿型TiO₂电子结构的影响，进而揭示N掺杂导致锐钛矿型TiO₂的禁带宽度变小的机理，对N掺杂TiO₂进行了基于密度泛函理论的第一性原理研究. 通过对能带、态密度及电子分布密度图的分析，发现在N掺杂后，N原子与Ti原子在导带区，发生了强烈的相互关联作用，致使Ti原子3d轨道上的电子向N原子2p轨道发生移动，使得导带降低了，从而使得TiO₂导带的禁带宽度变小.理论预测可以发生红移现象，与实验结果对比分析，理论与实验基本相符. 关键词： N掺杂 2')" href="#">锐钛矿型TiO₂ 电子结构     

Investigation on properties of TiO2 thin films deposited at different oxygen pressures

TiO₂ thin films were prepared by electron beam evaporation at different oxygen partial pressures. The influences of oxygen partial pressure on optical, mechanical and structural properties of TiO₂ thin films were studied. The results showed that with the increase of oxygen partial pressure, the optical transmittance gradually increased, the transmittance edge gradually shifted to short wavelength, and the corresponding refractive index decreased. The residual stresses of all samples were tensile, and the value increased as oxygen partial pressure increasing, which corresponded to the evolutions of the packing densities. The structures of TiO₂ thin films all were amorphous because deposition particles did not possess enough energy to crystallize.     

萤石结构TiO2的电子结构和光学性质

利用第一性原理计算了立方相萤石TiO₂的晶胞参数,能带结构和电子态密度.结果显示萤石TiO₂属于间接带隙半导体材料,其间接禁带宽度(Γ→X)E_g为2.07eV,比常见的金红石和锐钛矿TiO₂的禁带宽度窄.为了更清楚地了解萤石的光学性质,利用Kramers-Kronig色散关系,分别对萤石和金红石TiO₂的复介电常数、吸收率等参数进行了计算,并将二者结果做了 关键词： 2')" href="#">萤石结构TiO₂ 密度泛函理论 能带结构 光学性质     

萤石结构TiO2的电子结构和光学性质

利用第一性原理计算了立方相萤石TiO₂的晶胞参数，能带结构和电子态密度.结果显示萤石TiO₂属于间接带隙半导体材料，其间接禁带宽度(Γ→X)E_g为2.07eV，比常见的金红石和锐钛矿TiO₂的禁带宽度窄.为了更清楚地了解萤石的光学性质，利用Kramers-Kronig色散关系，分别对萤石和金红石TiO₂的复介电常数、吸收率等参数进行了计算，并将二者结果做了     

Deposition of Au/TiO2 film by pulsed laser

Au nanoparticles, which were photoreduced by a Nd:YAG laser in HAuCl₄ solution containing TiO₂ colloid and accompanied by the TiO₂ particles, were deposited on the substrate surface. The film consisting of Au/TiO₂ particles was characterized by the absorption spectra, scanning electron microscopy (SEM) and X-ray diffraction (XRD) analysis. The adhesion between the film and substrate was evaluated by using adhesive tape test. It was found that the presence of TiO₂ dramatically enhanced the adhesion strength between the film and the substrate, as well as the deposition rate of film. The mechanism for the deposition of Au/TiO₂ film was also discussed.     

Synthesis and photocatalytic oxidation of different organic dyes by using Mn2O3/TiO2 solid solution and visible light

Mn₂O₃/TiO₂ solid solution was prepared from two different oxides, manganese oxide (from KMnO₄ and ethanol) and TiO₂, these samples were characterized by BET, XRD, EDAX, SEM, FT-IR, ESR, XPS and UV–vis absorption spectroscopy. Photocatalytic activities of Mn₂O₃/TiO₂ powder was investigated by photooxidation of different dyes like Rhodamine B, thymol blue, methyl orange and Bromocresol green under visible light (300-W Xe lamp; λ > 420 nm). The results show that the alloy of TiO₂ with 1 mol% of Mn₂O₃ (MNT1) exhibit photocatalytic activity 3–5 times higher than that of P25 TiO₂ for oxidation of various dyes (RB, TB, MO and BG). The average particle size and crystallite size of MNT1 were found to be 100 nm and 12 nm measured from SEM and XRD, respectively. The EPR spectra of the Mn₂O₃/TiO₂ samples is a sharp five-line Mn(III) component centered on g_eff = 1.99.     

Preparation and photo-induced superhydrophilicity of composite TiO2-SiO2-In2O3 thin film

In this work, TiO₂-SiO₂-In₂O₃ composite thin films on glass substrates were prepared by the sol-gel dip coating process. X-ray diffraction (XRD), X-ray fluorescence spectroscopy (XRF) and X-ray photoelectron spectroscopy (XPS) were used to evaluate the structural and chemical properties of the films. UV-vis spectrophotometer was used to measure the transmittance spectra of thin films. The water contact angle (WCA) of thin films during UV/vis irradiation and storage in a dark place was measured by a contact angle analyzer. The results indicated that fabrication of composite film has a significant effect on transmittance and superhydrophilicity of TiO₂ films.     

SnO2/TiO2 mixed oxide particles synthesized in doped premixed H2/O2/Ar flames

SnO₂/TiO₂ mixed oxides with primary particle size ranging between 5 nm d_p 12 nm were synthesized by doping a H₂/O₂/Ar flame with Sn(CH₃)₄ and Ti(OC₃H₇)₄ co-currently. The effects of “flow coordinate,” concentration and flame configurations were investigated with respect to particle size and morphology of the generated mixed oxides. In situ characterization of the mixed oxides was performed using the particle mass spectrometer (PMS), while XRD, TEM, BET and UV–Vis were performed ex situ. Results obtained showed that primary particle size of mixed oxides can be controlled by varying experimental parameters. The mixed oxides have interesting properties compared to those of the pure oxides of TiO₂ and SnO₂, which were also synthesized in flames earlier. Band gap tuning opportunities are possible using mixed oxides.     

纤维状TiO2/Bi2O3光催化剂的制备及其光催化性能

以C₁₆H₃₆O₄Ti和Bi(NO₃)·5H₂O为原料,以棉花纤维为生物模板,合成了系列纤维状TiO₂/Bi₂O₃光催化剂．采用XRD、SEM、UV-Vis等测试技术对样品的相结构、形貌和吸光性能等进行了表征分析．结果表明,样品中的Bi₂O₃为单斜相和四方相共存的混晶,纤维长度达到毫米级,     

等离激元钼掺杂二氧化钛半导体的光催化固氮反应机理研究

近年来光催化固氮引起了广泛的关注,其代表了将N₂有效转化为NH₃的“绿色工业”的可持续发展路线,如何有效合理地设计这方面的光催化剂仍然是本领域地一个挑战. 本文提出了一种策略,即在高浓度掺杂的TiOsub>2中利用等离激元热电子来激活惰性Nsub>2分子. 成功合成的Mo掺杂TiOsub>2催化剂在常温常压条件下显示出高达134 μmol·g^-1·h^-1的NH₃催化效率,这与传统的等离激元贵金属所实现的催化效率相当. 通过超快光谱技术,发现该体系中的等离激元热电子激活了N₂分子,从而提高了TiO₂的催化活性. 本文为基于等离激元半导体的光催化固氮反应开辟了一条新的途径.     

Preparation and characterization of PES/TiO2 composite membranes

Polyethersulfone (PES)/TiO₂ composite membranes were prepared by phase inversion method with nano-TiO₂ as additive. The influence of TiO₂ on the morphologies and the performances of PES/TiO₂ membranes were investigated through the methods of SEM, XRD, TGA, contact angle goniometer, mechanical strength tests and filtration experiments. The results showed that the structure of membrane was not obviously affected by addition of TiO₂, and the performances such as hydrophilicity, thermal stability, mechanical strength and anti-fouling ability of membrane were enhanced through adding TiO₂ nanoparticles. At 0.5 wt.% TiO₂ content, the composite membrane has an excellent performance, however higher TiO₂ content (than 0.5 wt.%) resulted in defective pore structure of the membranes and decline of the performances, such as permeability and mechanical strength. TGA and mechanical strength analyses indicated good compatibility between polymers and TiO₂ nanoparticles.     

Effect of structure on the photocatalytic activity of Pt-doped TiO2 nanotubes

Highly ordered TiO₂ nanotubes with different tube length were fabricated by anodization using C₂H₂O₄·2H₂O containing 0.5 wt.% NH₄F (electrolyte A) and anhydrous dimethyl sulfoxide containing 1% HF (electrolyte B), respectively. Then cathodic reduction method was used to dope Pt in TiO₂ nanotubes in chloroplatinic acid. The results indicated that cathodic reduction could efficiently platinize TiO₂ nanotubes. Pt-doped TiO₂ nanotubes with the longer length had the higher photocatalytic activity for degrading methyl orange under UV and visible irradiation. The longer tube length has a positive effect on the photocatalytic activity of Pt-doped TiO₂ nanotubes. Besides, as the content of anatase further decreases, the photocatalytic activity drops gradually due to the reduction reaction in the surface area.