L10-ordered high coercivity (FePt)Ag-C granular thin films for perpendicular recording

We report (FePt)Ag-C granular thin films for potential applications to ultrahigh density perpendicular recording media, that were processed by co-sputtering FePt, Ag, and C targets on MgO underlayer deposited on thermally oxidized Si substrates. (FePt)_1−xAg_x-yvol%C (0<x<0.2, 0<y<50) films were fabricated on oxidized silicon substrates with a 10 nm MgO interlayer at 450^oC. We found that the Ag additions improved the L1₀ ordering and the granular structure of the FePt-C films with the perpendicular coercivity ranging from 26 to 37 kOe for the particle size of 5-8 nm. The (FePt)_0.9Ag_0.1-50vol%C film showed the optimal magnetic properties as well as an appropriate granular morphology for recording media, i.e., average grain size of D_av=6.1 nm with the standard deviation of 1.8 nm.     

Effect of Cr100−xTix (x = 0-19 at.%) alloy underlayers on the high coercivity of FePt thin film below the substrate temperature of 250 °C

The effect of Cr_100−xTi_x underlayer on orderd-L1₀ FePt films was investigated. A low-temperature ordering of FePt films could be attained through changing the Ti content of Cr_100−xTi_x underlayer. The ordering temperature of the 30 nm FePt film grown on 20 nm Cr₉₀Ti₁₀ underlayer was reduced to 250 °C which is practical manufacture process temperature. An in-plane coercivity was very high to 6000 Oe and a ratio of remnant magnetization (M_r) to saturation magnetization (M_s) was as large as 0.85. This result indicates that the coercivity obtained at 250 °C by the effect of CrTi underlayer is significantly higher than those obtained at 250-275 °C by the effect of underlayers in other conventional studies. The prominent improvement of the magnetic properties of ordered FePt thin films at low temperature of 250 °C could be understood with considering the strain-induced ordering phase transformation associated with lattice mismatch between Cr underlayer and FePt magnetic layer due to an addition of Ti content.     

Characteristics of Ni films deposited on SiO2/Si(1 0 0) and MgO(0 0 1) by direct current magnetron sputtering system with the oblique target

280 nm-thick Ni films were deposited on SiO₂/Si(1 0 0) and MgO(0 0 1) substrates at 300 K, 513 K and 663 K by a direct current magnetron sputtering system with the oblique target. The films deposited at 300 K mainly have a [1 1 0] crystalline orientation in the film growth direction. The [1 1 0]-orientation weakens and the [1 1 1]- and [1 0 0]-orientations enhance with increasing deposition temperature. The lattice constant of the Ni films is smaller than that of the Ni bulk, except for the film grown on MgO(0 0 1) at 663 K. Furthermore, as the deposition temperature increases, the lattice constant of the films grown on the SiO₂/Si(1 0 0) decreases whereas that of the films grown on the MgO(0 0 1) increases. The films deposited at 300 K and 513 K grow with columnar grains perpendicular to the substrate. For the films deposited at 663 K, however, the columnar grain structure is destroyed, i.e., an about 50 nm-thick layer consisting of granular grains is formed at the interface between the film and the substrate and then large grains grow on the layer. The Ni films deposited at 300 K consist of thin columnar grains and have many voids at the grain boundaries. The grains become thick and the voids decrease with increasing deposition temperature. The resistivity of the film decreases and the saturation magnetization increases with increasing deposition temperature.     

Nanocomposite L10 FePt–SiNx and FePt–SiNx–C films with large coercivity and small grain size on a TiN intermediate layer

FePt–SiN_x–C films with high coercivity, (001) texture and small grain size were obtained by co-sputtering FePt, Si₃N₄ and C on TiN/CrRu/glass substrate at 380 °C. Without C doping, FePt–SiN_x films with good perpendicular anisotropy and a single layer structure were obtained. However, the grain size was still too large and the grain isolation was poor. When C was doped into the FePt–SiN_x films, the out-of-plane coercivity increased due to the decrease of the exchange coupling. In addition, the grain size of the FePt films decreased, and well-separated FePt grains with uniform size were formed. The microstructure of [FePt–SiN_x 40 vol%]−20 vol% C films changed from a single layer structure to a multiple layer structure when the FePt thickness was increased from 4 to 10 nm. By optimizing the sputtering process, the [FePt (4 nm)–SiN_x 40 vol%]−20 vol% C (001) film with coercivity higher than 21.5 kOe, a single layer structure, and small average FePt grain size of 5.6 nm was obtained, which makes it suitable for ultrahigh density perpendicular recording.     

Magnetic viscosity effects in epitaxial L10 FePt thin films and exchange spring Fe–FePt bilayers

We have studied the thermal stability of L1₀ FePt thin films and Fe–FePt exchange-spring (ES) bilayers grown on (1 0 0) MgO by RF sputtering. The viscosity curves showed both for FePt films and bilayers a clear logarithmic decay of magnetization. Moreover, it was possible to evaluate the viscosity coefficient S for different applied reverse fields and the activation volumes at the coercivity. The latter values were then related to structural, magnetic and morphological measurements performed on the samples.     

Elaboration of (1 1 1)-oriented La-doped PZT thin films on platinized silicon substrates

PLZT thin films with different thickness were deposited in situ on platinum coated silicon substrates using a multi-target sputtering system. The purpose was to grow (1 1 1)-textured PLZT films on Pt (1 1 1). To this aim, the role of some key parameters on both crystalline quality and electrical properties was investigated. An ultra-thin TiO₂ seeding layer was deposited, prior to PLZT, which strongly affected the crystallographic orientation of the films. The relation between temperature deposition and film crystallinity is analysed. TEM observations show the presence of some very small grains of Zr_0.9La_0.1O_1.95 at the film bottom interface. In the range of thickness investigated, the plot of the inverse capacitance as a function of the film thickness split up into two different curves, each with a linear shape, which however allows determination of a single value of interface capacitance. Above a thickness of 400-500 nm a saturation of the dielectric properties seems to be reached.     

Low-temperature ordering of L10 FePt phase in FePt thin film with AgCu underlayer

FePt (20 nm) films with AgCu (20 nm) underlayer were prepared on thermally oxidized Si (0 0 1) substrates at room temperature by using dc magnetron sputtering, and the films annealed at different temperature to examine the disorder–order transformation of the FePt films. It is found that the ordered L1₀ FePt phase can form at low annealing temperature. Even after annealing at 300 °C, the in-plane coercivity of 5.2 kOe can be obtained in the film. With increase in annealing temperature, both the ordering degree and coercivity of the films increase. The low-temperature ordering of the films may result from the dynamic stress produced by phase separation in AgCu underlayer and Cu diffusion into FePt phase during annealing.     

Microstructure and magnetic properties of FePt:Ag nanocomposite films on SiO2/Si(1 0 0)

FePt:Ag nanocomposite films were prepared by pulsed filtered vacuum arc deposition system and subsequent rapid thermal annealing on SiO₂/Si(1 0 0) substrates. The microstructure and magnetic properties were investigated. A strong dependence of coercivity and ordering of the face-central tetragonal structure on both Ag concentration and annealing temperature was observed. With Ag concentration of 22% in atomic ratio, the coercivity got to 6.0 kOe with a grain size of 6.7 nm when annealing temperature was 400 °C.     

Scanning tunnelling microscopy studies of growth morphology in highly epitaxial c-axis oriented Pt thin film on (0 0 1) SrTiO3

A noble metal Pt thin film was successfully grown on (0 0 1) SrTiO₃ substrate by using a DC-sputtering technique. The surface morphology and growth features of the as-grown Pt films were investigated by scanning tunnelling microscopy. Growth conditions, such as pre-sputtering, deposition ambience, and oxygen ratio are found to greatly affect the orientation, the crystallinity, and the epitaxial behavior of Pt films on (0 0 1) SrTiO₃. Single-crystalline Pt films have been achieved by introducing a few percentage oxygen into the sputtering ambient. The in-plane-relationship of the c-axis oriented Pt thin films on (0 0 1) SrTiO₃ was determined to be (0 0 1)_Pt∥(0 0 1)_SrTiO3 and [0 0 1]_Pt∥[0 0 1]_SrTiO3. Oxygen in the sputtering ambient was found to be a key factor to achieve the epitaxial Pt films.     

Structural and magnetic properties of evaporated Fe thin films on Si(1 1 1), Si(1 0 0) and glass substrates

We present experimental results on the structural and magnetic properties of series of Fe thin films evaporated onto Si(1 1 1), Si(1 0 0) and glass substrates. The Fe thickness, t, ranges from 6 to110 nm. X-ray diffraction (XRD) and atomic force microscopy (AFM) have been used to study the structure and surface morphology of these films. The magnetic properties were investigated by means of the Brillouin light scattering (BLS) and magnetic force microscopy (MFM) techniques. The Fe films grow with (1 1 0) texture; as t increases, this (1 1 0) texture becomes weaker for Fe/Si, while for Fe/glass, the texture changes from (1 1 0) to (2 1 1). Grains are larger in Fe/Si than in Fe/glass. The effective magnetization, 4πM_eff, inferred from BLS was found to be lower than the 4πM_S bulk value. Stress induced anisotropy might be in part responsible for this difference. MFM images reveal stripe domain structure for the 110 nm thick Fe/Si(1 0 0) only.     

Amorphous Ni-Al underlayer-accelerated L10 ordering transition of FePt thin films

In the present study, we succeeded in accelerating the L1₀ ordering transition of FePt thin films by employing amorphous Ni-Al as underlayers. The coercivity H_c = 5 kOe and ordering parameter S = 0.67 of FePt thin films deposited on a Ni-Al underlayer with a thickness of ∼5 nm after 380 °C annealing for 30 min are significantly higher than those H_c = 0.4 kOe and S = 0.35 of the films without the Ni-Al underlayer. The L1₀ ordering process of and the coercivity of FePt thin films can be significantly tuned by varying the thickness of the Ni-Al underlayer.     

Effect of annealing temperature and annealing atmosphere on the structure and optical properties of ZnO thin films on sapphire (0 0 0 1) substrates by magnetron sputtering

ZnO thin films were epitaxially grown on sapphire (0 0 0 1) substrates by radio frequency magnetron sputtering. ZnO thin films were then annealed at different temperatures in air and in various atmospheres at 800 °C, respectively. The effect of the annealing temperature and annealing atmosphere on the structure and optical properties of ZnO thin films are investigated by X-ray diffraction (XRD), atomic force microscopy (AFM), photoluminescence (PL). A strong (0 0 2) diffraction peak of all ZnO thin films shows a polycrystalline hexagonal wurtzite structure and high preferential c-axis orientation. XRD and AFM results reveal that the better structural quality, relatively smaller tensile stress, smooth, uniform of ZnO thin films were obtained when annealed at 800 °C in N₂. Room temperature PL spectrum can be divided into the UV emission and the Visible broad band emission. The UV emission can be attributed to the near band edge emission (NBE) and the Visible broad band emission can be ascribed to the deep level emissions (DLE). By analyzing our experimental results, we recommend that the deep-level emission correspond to oxygen vacancy (V_O) and interstitial oxygen (O_i). The biggest ratio of the PL intensity of UV emission to that of visible emission (I_NBE/I_DLE) is observed from ZnO thin films annealed at 800 °C in N₂. Therefore, we suggest that annealing temperature of 800 °C and annealing atmosphere of N₂ are the most suitable annealing conditions for obtaining high quality ZnO thin films with good luminescence performance.     

Magnetoresistance of magnetite thin films grown by pulsed laser deposition on GaAs(1 0 0) and Al2O3(0 0 0 1)

Magnetotransport properties of magnetite thin films deposited on gallium arsenide and sapphire substrates at growth temperatures between 473 and 673 K are presented. The films were grown by UV pulsed laser ablation in reactive atmospheres of O₂ and Ar, at working pressure of 8 × 10⁻² Pa. Film stoichiometry was determined in the range from Fe_2.95O₄ to Fe_2.97O₄. Randomly oriented polycrystalline thin films were grown on GaAs(1 0 0) while for the Al₂O₃(0 0 0 1) substrates the films developed a (1 1 1) preferred orientation. Interfacial Fe³⁺ diffusion was found for both substrates affecting the magnetic behaviour. The temperature dependence of the resistance and magnetoresistance of the films were measured for fields up to 6 T. Negative magnetoresistance values of ∼5% at room temperature and ∼10% at 90 K were obtained for the as-deposited magnetite films either on GaAs(1 0 0) or Al₂O₃(0 0 0 1).     

Characterization of cubic phase MgZnO/Si(1 0 0) interfaces

The microstructural properties of the Mg_xZn_1−xO/Si(1 0 0) interface were investigated using transmission electron microscopy (TEM) and chemical states of the heterostructure were studied by high resolution X-ray photoelectron spectroscopy (XPS). By analyzing the valence band spectra of thin Mg_xZn_1−xO/Si(1 0 0) heterostructures, the valence band offset between such Mg_0.55Zn_0.45O and Si(1 0 0) was obtained to be 2.3 eV. Using the cubic ternary thin films as insulators, metal-insulator-semiconductor (MIS) capacitors have been fabricated. Leakage current density lower than 3 × 10⁻⁷ A/cm² is obtained under the electrical field of 600 kV/cm by current-voltage (I-V) measurement. Frenkel-Poole conduction mechanism is the main cause of current leakage under high electrical field.     

Surface morphology of epitaxial lattice-matched Ba0.7Sr0.3O on Si(0 0 1) and vicinal Si(0 0 1)-4°[1 1 0] substrates

Exploring ways for self-organized structuring of insulating thin films, we investigated the possibility to produce replicas of step trains, given by a vicinal Si(0 0 1)-4°[1 1 0] surface, in layers of crystalline and perfectly lattice-matched Ba_0.7Sr_0.3O. For this purpose, we carried out high-resolution spot profile analyses in low-energy electron diffraction (SPA-LEED) both on flat Si(0 0 1) and on Si(0 0 1)-4°[1 1 0]. Oxide layers were generated by evaporating the metals in oxygen ambient pressure with the sample at room temperature. Our G(S) analysis of these mixed oxide layers reveals a strong influence of local compositional fluctuations of Sr and Ba ions and their respective scattering phases, which appears as an unphysically large variation of layer distances. Nevertheless, we are able to show that quite smooth and closed oxide films are obtained with an rms roughness of about 1 ML. These Ba_0.7Sr_0.3O films directly follow the step train of Sr-modified vicinal Si surfaces that form (1 1 3) oriented facets after adsorption of a monolayer of Sr. This proves that self-organized structuring of insulating films can indeed be an effective method.     

FePt L10 ordering and grain growth using millisecond pulse laser processing

The structural and magnetic properties of ∼12 nm thick FePt thin films grown on Si substrates annealed using a 1064 nm wavelength laser with a 10 ms pulse have been examined. The A1 to L1₀ ordering phase transformation was confirmed by electron and X-ray diffraction. An order parameter near 50% and a maximum coercivity of 12 kOe were obtained with laser energy densities of 25-32 J/cm². Grain growth, quantified by dark field transmission electron microscopy, occurred during chemical ordering at the laser pulse widths studied.     

CoPt alloy grown on the WSe2(0 0 0 1) van der Waals surface

The structural and magnetic properties of 3-nm-thick CoPt alloys grown on WSe₂(0 0 0 1) at various temperature are investigated. Deposition at room temperature leads to the formation of a chemically disordered fcc CoPt alloy with [1 1 1] orientation. Growth at elevated temperatures induces L1₀ chemical order starting at 470 K accompanied with an increase in grain size and a change in grain morphology. As a consequence of the [1 1 1] growth direction, the CoPt grains can adopt one of the three possible variants of the L1₀ phase with tetragonal c-axis tilted from the normal to the film plane direction at 54°. The average long-range order parameter is found to be 0.35(±0.05) and does not change with the increase in the deposition temperature from 570 to 730 K. This behavior might be related to Se segregation towards the growing facets and surface disorder effects promoted by a high surface-to-volume ratio. Magnetic studies reveal a superparamagnetic behavior for the films grown at 570 and 730 K in agreement with the film morphology and degree of chemical order. The measurements at 10 K reveal the orientation of the easy axis of the magnetization lying basically in the film plane.     

Mössbauer spectroscopy and magnetic properties in thin films of FexNi100−x electroplated on silicon (1 0 0)

Fe_xNi_100−x thin films were produced by galvanostatic electrodeposition on Si (1 0 0), nominal thickness 2800 nm, and x ranging 7-20. The crystalline structure of the sample was determined by X-ray diffraction (XRD). The magnetic properties were investigated by vibration sample magnetometry (VSM) and room temperature ⁵⁷Fe Mössbauer spectroscopy. Conversion Electron Mössbauer spectroscopy (CEMS) in both film surfaces for the thick self-supported films showed that the magnetic moment direction is in the plane and conventional transmission (MS) that the directions are out of the plane films. The results were interpreted assuming a three-layer model where the external layer has in-plane magnetization and the internal one, out of plane magnetization.     

Study of Sm-doped ZnO samples sintered in a nitrogen atmosphere and deposited on n-Si(1 0 0) by evaporation technique

The samarium doping zinc oxide (Zn_1-xSm_xO) with (x=0.0, 0.04, 0.05 and 0.17) polycrystalline thin films have been deposited on n-Si(1 0 0) substrate using thermal evaporation technique. Ceramic targets for deposition were prepared by the standard solid-state reaction method and sintered in nitrogen atmospheres. X-ray diffraction and scanning electron microscopy analyses show that the bulk and films features reveal wurtzite crystal structure with a preferential (1 0 1) crystallographic orientation and grows as hexagonal shape grains. According to the results of the Hall effect measurements, all the films show p-type conductivity, possibly a result of nitrogen incorporation into the Sm-doped ZnO samples. Magnetic measurements show that ferromagnetic behavior depends on the Sm³⁺ concentration. For a film with lower Sm₂O₃ contents (x=0.04), a phenomenon of paramagnetism has been observed. While, with further increase of Sm³⁺ contents (x=0.05) the ferromagnetic behavior has been observed at room temperature. However, at higher doping content of Sm³⁺, the ferromagnetic behavior was suppressed. The decrease of ferromagnetism with increasing doping concentration demonstrates that ferromagnetism observed at room temperature is an intrinsic property of Zn_1-xSm_xO films.     

Role of crystal orientation on the magnetic properties of CoFe2O4 thin films grown on Si (1 0 0) and Al2O3 (0 0 0 1) substrates using pulsed laser deposition

We report the influence of crystal orientation on the magnetic properties of CoFe₂O₄ (CFO) thin films grown on single crystal Si (1 0 0) and c-cut sapphire (Al₂O₃) (0 0 0 1) substrates using pulsed laser deposition technique. The thickness was varied from 200 to 50 nm for CFO films grown on Si substrates, while it was fixed at 200 nm for CFO films grown on Al₂O₃ substrates. We observed that the 200 and 100 nm thick CFO-Si films grew in both (1 1 1) and (3 1 1) directions and displayed out-of-plane anisotropy, whereas the 50 nm thick CFO-Si film showed only an (1 1 1) orientation and an in-plane anisotropy. The 200 nm thick CFO film grown on an Al₂O₃ substrate was also found to show a complete (1 1 1) orientation and a strong in-plane anisotropy. These observations pointed to a definite relation between the crystalline orientation and the observed magnetic anisotropy in the CFO thin films.