Drive-based recording analyses at >800 Gfc/in using shingled recording

Since the introduction of perpendicular recording, conventional perpendicular scaling has enabled the hard disk drive industry to deliver products ranging from ∼130 to well over 500 Gb/in² in a little over 4 years. The incredible areal density growth spurt enabled by perpendicular recording is now endangered by an inability to effectively balance writeability with erasure effects at the system level. Shingled magnetic recording (SMR) offers an effective means to continue perpendicular areal density growth using conventional heads and tuned media designs. The use of specially designed edge-write head structures (also known as ‘corner writers’) should further increase the AD gain potential for shingled recording. In this paper, we will demonstrate the drive-based recording performance characteristics of a shingled recording system at areal densities in excess of 800 Gb/in² using a conventional head.Using a production drive base, developmental heads/media and a number of sophisticated analytical routines, we have studied the recording performance of a shingled magnetic recording subsystem. Our observations confirm excellent writeability in excess of 400 ktpi and a perpendicular system with acceptable noise balance, especially at extreme ID and OD skews where the benefits of SMR are quite pronounced. We believe that this demonstration illustrates that SMR is not only capable of productization, but is likely the path of least resistance toward production drive areal density closer to 1 Tb/in² and beyond.     

The potential of bit patterned media in shingled recording

Shingled recording on continuous and bit patterned media (BPM) is compared. From a recording viewpoint, continuous media have the advantage due to the lack of a need to synchronise writing with dot position. For BPM the write windows at 4 Tbit/in² are only a couple of nm across, requiring extremely tight manufacturing tolerances. In readback, BPM have the higher SNR over a wide range of areal densities due to the absence of transition noise and erase bands. Significant increases in areal density could be achieved using BPM, provided dot uniformity could be maintained.     

Review of perpendicular magnetic recording research at Fujitsu

Perpendicular magnetic recording (PMR) research and development (R&D) was carried out at Fujitsu for 32 years from 1978 to 2009, separated into three stages. We developed PMR for use in hard disk drives (HDDs). We sputtered Co-Cr alloy thin film onto a disk substrate and evaluated it using thin-film heads. Some interesting results were obtained at each stage. On the way we fabricated 1.8″ HDDs in 1992 and finally shipped the mass-produced PMR HDDs in 2006. Unfortunately, the HDD business at Fujitsu closed down. I would like to review the exceptional PMR research undertaken at Fujitsu.     

Effect of discrete track medium at high areal density

The degradation of SNR caused by the higher uniaxial crystalline anisotropy field (Hk) of medium and small write fields of narrower write width is one of the problems for achieving higher areal density. The SNR dependence on Hk of a medium with different write fields of head using the discrete track medium (DTM) is investigated by using micromagnetics simulation. As a result, the curves of SNR as a function of Hk have peak values. In DTM, the peak values of SNR are almost constant at any Hk of the medium and different write fields. Higher SNR is realized even at low Hk and small write field in DTM.     

The role of nucleation field of media in heat-assisted magnetic probe recording

We characterize a method of heat-assisted magnetic probe recording on perpendicular media. Heating source is field emission current from a scanning tunneling microscope (STM) tip. Recording media are three kinds of magnetic films, Co/Pt, CoNi/Pt, and Co/Pd multilayers with different nucleation fields. Pulses with amplitude of 5 V were applied between the STM tip and the recording medium. Experiments show that magnetic marks with an average size of 180 nm were formed on both Co/Pt and CoNi/Pt films whose nucleation fields are greater than their saturation magnetization. No marks were observed on the Co/Pd film whose nucleation field is smaller than its saturation magnetization. A model is built to simulate the dynamic process of domain formation in probe-based magnetic recording system. Simulation results agree with experiments and it explains the effect of the nucleation field of medium in perpendicular recording.     

Optimizing head/media electrical characterization in the presence of skew at high track density

The skew angle causes a discrepancy in determining the reader-to-writer offset (RWO) when using different periodical patterns in track profile tests. It also separates the peak overwrite (OW) from the peak high frequency amplitude HFA, (1 T periodical pattern) on corresponding track profiles. Furthermore, higher track density and larger skew angle exacerbate the skew effect and induce more RWO error, thus impacting the parametric performance optimization. Simulation studies are used to interpret the skew effect on the RWO determination and OW cross-track characteristics. Based on experimental investigations and simulation analyses, using the HFA, track profile for deriving the optimal RWO is proposed for spin-stand tests. Actual parametric characterization has proven that the optimal RWO minimized the skew effect and the RWO error, thus improving the parametric performance and reducing the test variation. The method is beneficial and necessary for the high track density characterization.     

Looking back at perpendicular magnetic recording R&D in NEC

This paper reports perpendicular magnetic recording (PMR) circumstances and the results based on the reference published by NEC. The PMR flexible disks using Co-Cr-Ta films were investigated. Pass wear durability of Co-Cr-Ta film strongly depends on the base film surface roughness and Young's modulus values of Co-Cr-Ta films. Pass wear durability, more than 10 million passes, was confirmed under a high temperature (60 °C) and a high humidity (80% RH) condition, as well as a low temperature (5 °C) condition. The read/write characteristics for double-layered PMR media were examined by using a combination of a single-pole-type (SPT) write head and a magnetoresistive (MR) read head, and a conventional merged ring type inductive (ID) write head/MR read head. By differential equalization of the reproduced voltage, the bit error rate less than 10⁻⁶ at 3 Gb/in.² was obtained for the SPT/MR head combination. The antenna effect for PMR realization was analyzed using the merged ring type ID/MR head. In order to increase the magnetic circuit resistance from the ID head pole to the soft underlayer, we developed the sendust (FeAlSi) soft underlayer with low magnetic permeability. We confirmed that the recorded signal has better stability under the ID/MR head-loaded condition than the SPT head-loaded condition. These results show that there are the head and media solutions to realize PMR. We had confidence that we could use the basic structure of the commercial ID/MR head for the PMR head.     

Measurement of radon and thoron concentration by using LR-115 type-II plastic track detectors in the environ of Brahmaputra Valley, Assam, India

Radon/thoron and their progeny concentrations were measured in different types of dwellings at different locations around industrial areas, cities and rural areas of Brahmaputra Valley of Assam by using LR-115 (type-II) plastic detector. Radon levels of different dwellings were analysed with reference to the nature of building materials, ventilation patterns and the types of underlying soil. The results were discussed under the light of exposure limits set by ICRP. The average concentrations of indoor radon and thoron varied from 39.5 to 215.2 Bqm⁻³ and 12.9 to 37.6 Bqm⁻³, respectively. The estimated inhalation dose due to radon, thoron and their daughter products in the study areas varied from 0.53 to 1.00 μSvh⁻¹.     

低密度聚乙烯热压成型过程中的空间电荷

借助开路热刺激放电(TSD)电流及原位实时电荷TSD和电荷等温衰减测量，研究了低密度聚乙烯(LDPE)在热压成型过程中所产生的空间电荷特性.结果表明具有良好室温稳定性的成型电荷被束缚在两类陷阱能级中：浅阱和深阱，其陷阱中心深度分别约为0.92eV和1.31eV.初步的分析进一步表明了它们应该分别位于试样的表层和体内，为近表面陷阱和体陷阱. 关键词： 低密度聚乙烯(LDPE) 热压成型 空间电荷 热刺激放电(TSD)