Preparation and characterization of flaky FeSiAl composite magnetic powder core coated with MnZn ferrite

The flattening of FeSiAl soft magnetic powder was achieved by ball milling process, and MnZn/FeSiAl composite magnetic powder core was prepared by press molding. The effect of different coating amount of MnZn ferrite on the soft magnetic properties of FeSiAl was studied. At the same time, the optimal stress-relieving annealing temperature of the composite magnetic powder core is revealed. The results showed that the addition of MnZn ferrite affected the magnetic properties such as saturation magnetization (Ms), initial permeability (μi) and power loss (Pcm) of FeSiAl soft magnetic. With the increase of MnZn ferrite addition content, the saturation magnetization of composites decreased gradually, and the magnetic permeability increased first and then decreased, and the loss decreased first and then increased. When the addition content of MnZn ferrite was 5%, the permeability reached the maximum, which was 28.1% higher than that of the pure FeSiAl magnetic powder core under the same conditions. At the same time, the loss was the lowest, which was 13.3% lower than the pure FeSiAl powder core under the same conditions. When the annealing temperature is around 650 °C, the magnetic powder core has the largest magnetic permeability and the lowest loss.     

Effect of Fe/Sr mole ratios on the formation and magnetic properties of SrFe12O19 microtubules prepared by sol-gel method

The sol was obtained by sol-gel method. Then, the sol was dripped onto the absorbent cotton template. The gel was obtained after the evaporation of water. Strontium ferrite microtubules were prepared after carrying out calcination process at different temperatures. The phase, morphology and particle diameter and the magnetic properties of samples were studied by X-ray diffraction (XRD), scanning electron microscopy (SEM) and vibrating sample magnetometer (VSM), respectively. The effects of Fe³⁺/Sr²⁺ mole ratio and calcination temperature on the crystal structure, morphology and magnetic properties of ferrite microtubules were studied. The external diameters of obtained SrFe₁₂O₁₉ microtubules were found to range between 8 and 13 μm; the wall thicknesses ranged between 1 and 2 μm. When the Fe³⁺/Sr²⁺ mole ratio and the calcination temperature were 11.5 and 850 °C, respectively, the coercivity, saturation magnetization and remanent magnetization for the samples were 7115.1 Oe, 70.1 and 42.4 emu/g, respectively. The mechanism of the formation and variation in magnetic properties of the microtubules were explained.     

Heat treatment effects on microstructure and magnetic properties of Mn-Zn ferrite powders

Mn-Zn ferrite powders (Mn_0.5Zn_0.5Fe₂O₄) were prepared by the nitrate-citrate auto-combustion method and subsequently annealed in air or argon. The effects of heat treatment temperature on crystalline phases formation, microstructure and magnetic properties of Mn-Zn ferrite were investigated by X-ray diffraction, thermogravimetric and differential thermal analysis, scanning electron microscopy and vibrating sample magnetometer. Ferrites decomposed to Fe₂O₃ and Mn₂O₃ after annealing above 550 °C in air, and had poor magnetic properties. However, Fe₂O₃ and Mn₂O₃ were dissolved after ferrites annealing above 1100 °C. Moreover, the 1200 °C annealed sample showed pure ferrite phase, larger saturation magnetization (M_s=48.15 emu g⁻¹) and lower coercivity (H_c=51 Oe) compared with the auto-combusted ferrite powder (M_s=44.32 emu g⁻¹, H_c=70 Oe). The 600 °C air annealed sample had the largest saturation magnetization (M_s=56.37 emu g⁻¹) and the lowest coercivity (H_c=32 Oe) due to the presence of pure ferrite spinel phase, its microstructure and crystalline size.     

Dielectric and magnetic properties of low-temperature fired NiCuZn-BaTiO3 composites

The composition effects on the dielectric and magnetic properties of NiCuZn-BaTiO₃ composites fired at low temperature were investigated. The coexistence of perovskite BaTiO₃ and spinel ferrite phases in the composites were observed; no significant chemical reactions occurred between BaTiO₃ and NiCuZn ceramics during sintering. The nanosized BaTiO₃ powders favored a decrease in grain size. The saturation magnetization, remanent magnetization and real permeability continuously decreased with increasing BaTiO₃ content. And the real permittivity continuously increased with the BaTiO₃ content. The Q-factor (quality factor) exhibited relatively high values with 20-30 wt% BaTiO₃. All composite materials exhibited a low dielectric loss below 100 MHz. Synthetically considerations, the composites with 20-30 wt% BaTiO₃ could obtain relatively high real permeability and real permittivity values, and the magnetic and dielectric losses were relatively low, so they were the best candidates to produce LC-integrated chip elements.     

MFM studies of magnetic domain patterns in bulk barium ferrite (BaFe12O19) single crystals

Magnetic domain patterns in bulk barium ferrite (BaFe₁₂O₁₉; BaM) single crystals on the basal plane and the prism plane were measured and studied by magnetic force microscopy (MFM). The surface domain pattern is in the form of flowers or star on the basal plane and long elongated spikes or stripe domains on the prism plane. The change in domain structure with applied field (H_app) and the thickness (T) dependence on domain width (δ) was observed. The domain width decreased from 32 to 9 μm for the crystals of 800-100 μm thicknesses, respectively.     

Correlation between site preference and magnetic properties of substituted strontium ferrite thin films

SrFe_12−x(Sn_0.5Zn_0.5)_xO₁₉ thin films with x=0−5 were synthesized by a sol-gel method on thermally oxidized silicon wafer (Si/SiO₂). The site preference and magnetic properties of Zn-Sn substituted strontium ferrite thin films were studied using ⁵⁷Fe Mössbauer spectroscopy and magnetic measurements. Mössbauer spectra displayed that the Zn-Sn ions preferentially occupy the 2b and 4f₂ sites. The preference for these sites is responsible for the anomalous increase in the magnetization at high Zn-Sn substitutions. X-ray diffraction (XRD) patterns and field emission scanning electron microscope (FE-SEM) micrographs demonstrated that single phase c-axis hexagonal ferrite films with rather narrow grain size distribution were obtained. Vibrating sample magnetometer (VSM) was employed to probe magnetic properties of samples. The maximum saturation of magnetization and coercivity at perpendicular direction were 265 emu/g and 6.3 kOe, respectively. It was found that the complex susceptibility has linear variation with static magnetic field.     

Study of magnetic properties and magnetoelectric effect in (x) Ni0.5Zn0.5Fe2O4+(1−x)PZT composites

Magnetoelectric (ME) composites consisting of ferrite phase (x) Ni_0.5Zn_0.5Fe₂O₄+ferroelectric phase (1−x)Pb Zr_0.8Ti_0.2O₃ (Lead Zirconate Titanate—PZT) in which x (mol%) varies between 0 and 1 (0.0≤x≤1.0) was synthesized by double sintering ceramic method. The presence of constituent phases of ferrite, ferroelectric and their composites was confirmed by X-ray diffraction studies. The hysteresis measurement was used to study magnetic properties such as saturation magnetization (M_S) and magnetic moment (μ_B). The existence of single domain (SD) particle in the ferrite phase and mixed (SD+MD) particle in the composites was studied from AC susceptibility measurements. ME voltage coefficient for each mol% of ferrite phase was measured as a function of applied DC magnetic field and at the same time influence of magnetic field on ME response and resistivity of composites was studied. The maximum ME voltage coefficient of 0.84 mV/cm Oe was observed for 15% of ferrite phase and 85% of ferroelectric phase in the composites.     

Magnetic reversal mechanism in strong perpendicular magnetic anisotropic CoPt/AlN multilayer film

Magnetic reversal mechanism of the Sub/AlN5 nm/[CoPt2 nm/AlN5 nm]₅ nano multilayer film, which shows strong perpendicular magnetic anisotropy (K_u=6.7×10⁶ erg/cm³), has been studied. The angle-dependent magnetic hysteresis loops of this highly perpendicular anisotropic CoPt/AlN multilayer film were measured in the present work, applying a magnetic field along different angles φ with respect to the film normal. It demonstrates that the magnetic reversal of the CoPt ultrathin layers in the CoPt/AlN multilayer film is occurred by the reversible magnetization rotation and the irreversible displacement of domain walls. The φ-dependent part of coercive field is resulted from the internal stress according to the Kondorsky and Kersten model. The φ-independent part of coercive field implies some random and isotropy pinning centers (e.g., vacancies, dislocations, grain boundaries) in the ultrathin CoPt layers. Our work is useful for coercivity control of metal/ceramics layered structures, in particular the perpendicular magnetic tunneling junctions.     

Structural and magnetic properties of NiZn ferrite films with high saturation magnetization deposited by magnetron sputtering

NiZn ferrite films with well-defined spinel crystal structure were in situ fabricated by radio frequency magnetron sputtering at room temperature. The microstructures and static magnetic properties of the films’ dependence on the partial pressure ratio of argon to oxygen gas were investigated. Scanning electron microscope images indicated that all the films consisted of particles nanocrystalline in nature and the sizes increase as the ratio increases in the range of 10-25 nm. A large saturation magnetization (237.2 emu/cm³) and a minimum of coercivity (68 Oe) were obtained when the ferrite film was deposited in the ratio of 4:1. The complex permeability values (μ = μ′−iμ″) of the film were measured at frequency up to 5 GHz. It was shown that the film exhibited a large real part of permeability μ′ of 18 and a very high resonance frequency f_r of 1.2 GHz. The results suggested that the NiZn ferrite film as-deposited in the ratio of 4:1 may be promised as magnetic medium in the application of integrated circuits operating at microwave frequencies.     

Synthesis and characterization of hard magnetic composites—Hollow microsphere/titania/barium ferrite

Hard magnetic composites—hollow microsphere (core)/titania (intermediate layer)/barium ferrite (magnetic shell) (M/T/B) were prepared by wet-chemical method. Barium ferrite nanoparticles were directly coated on the rutile titania-coated hollow microsphere forming light hard magnetic composites using sol-gel technique. The prepared composites were characterized with FESEM, EDS, XRD and vibrating sample magnetometry. The composites are composed of barium ferrite, hematite, titania and mullite. For the samples with 40 wt.% barium ferrite, its specific saturation magnetization with titania is increased to 17.88 emu/g in comparison with 9.6 emu/g without titania. The function of titania in the composites is also discussed.     

Mechanical alloyed Ho doping in CoFe2O4 spinel ferrite and understanding of magnetic nanodomains

We doped Ho³⁺ in CoFe_1.95Ho_0.05O₄ spinel ferrite by mechanical alloying and subsequent annealing at different temperatures (600-1200 °C). We understood the structural and magnetic properties of the samples using X-ray diffraction, SEM, Thermal analysis (TGA and DTA), and VSM measurement. The samples have shown structural stabilization within cubic spinel phase for the annealing temperature (T_AN)≥800 °C. Thermal activated grain growth kinetics has been accompanied with the substantial decrease in lattice strain. The gain size dependent magnetism is evident from the variation of magnetic moment, remanent magnetization and coercivity of the material. The paramagnetic to ferrimagnetic transition temperature T_C (∼805 K) seems to be grain size independent in the present material. The magnetic nanograins, either single domain/pseudo-single domain (50-64 nm) or multi-domain (above 64 nm) regime, showed superparamagnetic blocking below T_m, which is below T_C (805 K) and also well above the room temperature.     

The synthesis and the magnetic properties of Gd-doped FexCo1−x/CoyFe3−yO4 micro-octahedrons composites

Gd³⁺-substituted micro-octahedron composites (Fe_xCo_1−x/Co_yGd_zFe_3−y−zO₄) in which the Fe-Co alloy has either a bcc or fcc structure and the oxide is a spinel phase were fabricated by the hydrothermal method. The X-ray diffraction (XRD) patterns indicate that the as-synthesized Gd³⁺-substituted micro-octahedron composites are well crystallized. Scanning electron microscopy (SEM) images show that the final product consists of larger numbers of micro-octahedrons with the size ranging from 1.3 to 5 μm, and the size of products are increased with increasing the concentration of KOH. The effect of the Co²⁺/Fe²⁺ ratio (0?Co²⁺/Fe²⁺?1) and substitution Fe³⁺ ions by Gd³⁺ ions on structure, magnetic properties of the micro-octahedrons composites were investigated, and a possible growth mechanism is suggested to explain the formation of micro-octahedrons composites. The magnetic properties of the structure show the maximal saturation magnetization (107 emu/g) and the maximal coercivity (1192 Oe) detected by a vibrating sample magnetometer.     

Understanding the magnetic ground state of rare-earth intermetallic compound Ce4Sb3: Magnetization and neutron diffraction studies

Magnetization and neutron diffraction studies have been performed on Ce₄Sb₃ compound (cubic Th₃P₄-type, space group I4¯3d, no. 220). Magnetization of Ce₄Sb₃ reveals a ferromagnetic transition at ∼5 K, the temperature below which the zero-field-cooled and field-cooled magnetization bifurcate in low applied fields. However, a saturation magnetization (M_S) value of only ∼0.93μ_B/Ce³⁺ is observed at 1.8 K, suggesting possible presence of crystal field effects and a paramagnetic/antiferromagnetic Ce³⁺ moment. Magnetocaloric effect in this compound has been computed using the magnetization vs. field data obtained in the vicinity of the magnetic transition, and a maximum magnetic entropy change, −ΔS_M, of ∼8.9 J/kg/K is obtained at 5 K for a field change of 5 T. Inverse magnetocaloric effect occurs at ∼2 K in 5 T indicating the presence of antiferromagnetic component. This has been further confirmed by the neutron diffraction study that evidences commensurate antiferromagnetic ordering at 2 K in zero magnetic field. A magnetic moment of ∼1.24μ_B/Ce³⁺ is obtained at 2 K and the magnetic moments are directed along Z-axis.     

Optical sensing characteristics of the photonic crystal fiber filled with magnetic fluid

A novel photonic crystal fiber sensing theory filled with magnetic fluid is proposed based on the change of the MF refractive index under varied magnetic field. The magnetically induced tuning of the magnetic fluid filled PCF propagation properties were investigated by the full-vector finite element method with a perfectly matched layer. Theoretical calculations show that both the effective refractive index and the effective mode area increase vs. the increased magnetic field, and the PCF filled MF with larger d/Λ is more sensitive to magnetic field. When the wavelength λ = 1550 nm, the duty ratio d/Λ = 0.9, d/Λ = 0.6, the effective refractive indexes increase respectively from 1.598279 to 1.617572, from 1.61948 to 1.632484, and the effective mode areas increase respectively from 3.561115 μm² to 7.052360 μm², from 6.167494 μm² to 37.221998 μm² as the magnetic field changes from 25 Oe to 175 Oe. This scheme provides theoretical foundation to use magnetic field to control light in photonic crystal fiber and also offers a potential method for magnetic field sensing based on the TIR-PCF.     

Microstructure and magnetic properties of Sn-substituted MnZn ferrites

Sn-substituted MnZn ferrites were prepared by conventional oxide ceramic process. The influences of Sn substitution on microstructure and magnetic properties of MnZn ferrites were investigated. The results indicated that with increase of Sn substitute concentration, the diffraction peaks shifted slightly towards the lower angles and the lattice parameter (a) increased. And at room temperature, the bulk density (d_m), initial permeability (μ_i), saturation magnetic induction (B_s) and electrical resistivity (ρ) of Sn-substituted MnZn ferrites all increased initially and then decreased with the further increase of Sn substitute concentration, while the power losses decreased first and then increased subsequently. Meanwhile, the temperature of secondary maximum peak of μ_i-T curve and the minimum losses moved to lower temperature while the Sn substitute concentration increased. When the content of Sn substitution was 0.3 mol%, at room temperature, the initial permeability, saturation magnetic induction, density and electrical resistivity reached their maxima, while the hysteresis loss (P_h), eddy current loss (P_e) and total losses (P_cv) achieved their minima. The P_h∼T and μ_i-T curves varied contrarily, and due to the contribution of extra eddy current loss (P_e,exc) that was proportional to P_h, the P_e-T curve did not agree with its classical expression. Finally, MnZn ferrite substituted with 0.3 mol% SnO₂ shows the highest initial permeability (3894) and lowest losses (303 kW/m³) at room temperature.     

Dependence of microwave absorption properties on ferrite volume fraction in MnZn ferrite/rubber radar absorbing materials

We report the analysis of measurements of the complex magnetic permeability (μ_r) and dielectric permittivity (ε_r) spectra of a rubber radar absorbing material (RAM) with various MnZn ferrite volume fractions. The transmission/reflection measurements were carried out in a vector network analyzer. Optimum conditions for the maximum microwave absorption were determined by substituting the complex permeability and permittivity in the impedance matching equation. Both the MnZn ferrite content and the RAM thickness effects on the microwave absorption properties, in the frequency range of 2-18 GHz, were evaluated. The results show that the complex permeability and permittivity spectra of the RAM increase directly with the ferrite volume fraction. Reflection loss calculations by the impedance matching degree (reflection coefficient) show the dependence of this parameter on both thickness and composition of RAM.     

Resin-bonded permanent magnetic films with out-of-plane magnetization for MEMS applications

Resin-bonded permanent magnets with out-of-plain direction of magnetization and improved magnetic properties for magnetic MEMS actuator have been created. The material investigated consists of magnetically anisotropic strontium ferrite particles embedded into epoxy resin matrix upto a volume loading of 80%. Intrinsic coercivity H_ci of 6000 Oe (480 kA/m), residual magnetic flux density B_r up to 4000 G (0.4 T) and maximum energy product (BH)_max of 3.0 MG Oe (23.6 kJ/m³) have been attained due to magnetic-field-induced alignment of the ferrite particles during curing process.     

Preparation, magnetic and electromagnetic properties of polyaniline/strontium ferrite/multiwalled carbon nanotubes composite

Strontium ferrite particles were firstly prepared by sol-gel method and self-propagating synthesis, and then the polyaniline/strontium ferrite/multiwalled carbon nanotubes composites were synthesized through in situ polymerization approach. Structure, morphology and properties of the composite were characterized by various instruments. XRD analysis shows that the output of PANI increases with the increase of the content of MWCNTs, due to the large surface area of MWCNTs. Because of the coating of PANI, the outer diameter of MWCNTs increases from 10 nm to 20-40 nm. The electrical conductivity of the composites increases with the amount increase of MWCNTs and reaches 7.2196 S/cm in the presence of 2 g MWCNTs. The coercive force of the composites prepared with 2 g MWCNTs is 7457.17 Oe, which is much bigger than that of SrFe₁₂O₁₉ particles 6145.6 Oe, however, both the saturation magnetization and the remanent magnetization of the composite become much smaller than those of SrFe₁₂O₁₉ particles. The electromagnetic properties of the composite are excellent in the frequency range of 2-18 GHz, which mainly depend on the dielectric loss in the range of 2-9 GHz, and mainly on the magnetic loss in the range of 9-18 GHz.     

Magnetic spectra of Fe-based nanocrystalline wires with axial or transverse domains

The circular permeability μ′=μ′−jμ″ of two Fe-based soft magnetic wires with axial and transverse domains, has been determined from the measurements of impedance Z=R+jX as functions of frequency (f=10-10⁵ Hz) and AC current amplitude (I=0.1-100 mA). From the magnetic spectra of μ′−f and μ″−f for a few circular fields (H_φ=0.4, 1.2, 4, 12, 40 A/m), we found that the sample with axial domain structure exhibits a relaxational feature, while for the one with transverse domain resonance-like spectra were observed when the circular field H_φ≥4 A/m. These results have been discussed in terms of domain structure and circular magnetization processes.     

Investigations on structural and magnetic properties of cobalt ferrite/silica nanocomposites prepared by the coprecipitation method

Magnetic nanocomposites consisting of cobalt ferrite nanoparticles embedded in silica matrix were prepared by the coprecipitation method using metallic chlorides as precursors for ferrite. Subsequently composites were annealed at 100, 200 and 300 °C for 2 h. The samples were structurally characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and transmission electron microscopy (TEM). The magnetic properties were measured in the temperature range of 10-300 K using vibrating sample magnetometer (VSM). The effects of thermal treatment on structural and magnetic properties of nanocomposites were investigated. When the samples were annealed, CoFe₂O₄ nanocrystallites were observed in the SiO₂ matrix, whose size increases with increase in annealing temperature. The coercivity and saturation magnetization of nanocomposite (annealed at 300 °C for 2 h) are much higher than that of bulk cobalt ferrite. The realization of adjustable particle sizes and controllable magnetic properties makes the applicability of the CoFe₂O₄ nanocomposite more versatile.