基于5-氨基邻甲酚的膦配体的合成及在乙烯齐聚中的应用

以5-氨基邻甲酚与二苯基氯化膦为原料,通过取代反应合成了一种含有PNP和P—O结构的膦配体并确定了其结构.通过与Cr(acac)_3原位生成以及与Cr Cl3(THF)_3预制的方法制成配合物作为主催化剂,以甲基铝氧烷(MAO)为助催化剂,形成催化体系用于催化乙烯齐聚反应,考察了溶剂种类、反应温度、反应压力及Al/Cr摩尔比对该催化剂的活性和选择性的影响,并与原位生成的邻位和对位氨基酚类膦配体催化体系催化乙烯齐聚反应效果进行了对比.试验结果表明,以环己烷为溶剂,MAO为助催化剂,当反应温度为50℃、反应压力为2.5 MPa、Al/Cr摩尔比为700的条件下,该催化剂的活性最高达5.91×10~6 g/(mol·Cr·h),液相产物中1-辛烯选择性高达72.94%,1-己烯和1-辛烯总的选择性为82.11%.     

一种后过渡金属催化剂催化乙烯低聚动力学研究

设计并合成了一种新型的后过渡金属铁络合物 { [(2 ArNC(Me) ) 2 C5H3N]FeCl2 } (Ar =2 ,4 C6 H4(CH3) 2 ) ,研究了该络合物 甲基铝氧烷 (MAO)催化乙烯低聚 ,讨论了低聚反应温度、Al Fe摩尔比、催化剂浓度、反应压力等对催化剂活性及反应速率的影响 .本催化剂的最大特点是活性高 (在 30℃ ,3 0MPa时活性可达 4 2 6× 10 8goligomer·molFe·h- 1 )、初速度大 ,动力学曲线为衰减型 .     

新型树枝状桥联镍配合物的合成及催化烯烃齐聚性能

合成了一种N,N-二齿配位的新型树枝状桥联吡啶亚胺配体及其镍配合物,利用元素分析、傅里叶变换红外光谱(FTIR)和电喷雾电离质谱(ESI-MS)对其结构进行了表征.以二氯乙基铝(Et Al Cl2)为助催化剂,考察了树枝状桥联镍配合物催化乙烯齐聚和1-戊烯齐聚的聚合条件对产物分布的影响.结果表明,当聚合时间为60 min,聚合压力为0.5 MPa,Al/Ni摩尔比为150时,乙烯齐聚产物中C10~C14的选择性最高,达到93%,催化活性为0.99×106g/(mol Ni·h);当聚合时间为60 min,Al/Ni摩尔比为300时,1-戊烯齐聚产物中C20的选择性最高为70.5%,催化活性为2.47×105g/(mol Ni·h).该树枝状桥联镍配合物对乙烯齐聚反应和1-戊烯齐聚反应均具有良好的催化活性和较高碳数的齐聚产物选择性.     

费-托合成Fe1-xO基熔铁催化剂的研究

 采用高温熔融法制备了用于费-托合成的Fe1-xO基熔铁催化剂,考察了其在n(H2)/n(CO)=2,温度573 K,压力1.4 MPa和空速为12?600 h-1下的催化性能. 结果表明,与Fe3O4基熔铁催化剂相比,Fe1-xO基熔铁催化剂具有较高的催化F-T合成反应的活性、较低的WGS反应选择性和较强的加氢能力. XRD结果表明,经F-T反应后的熔铁催化剂存在Fe5C2和Fe3O4两种物相,但Fe1-xO基熔铁催化剂中Fe5C2的晶粒尺寸小于Fe3O4基熔铁催化剂中Fe5C2的晶粒尺寸.     

过渡金属乙烯齐聚与聚合催化剂研究进展

综述了近年来过渡金属配合物催化乙烯齐聚与聚合的最新进展;介绍了乙烯齐聚或聚合的反应时间、反应温度、乙烯压力、助催化剂用量等反应条件及配体上不同取代基对前过渡金属(铬,锆,钛,钒)和后过渡金属(铁,钴,镍,铜)配合物的催化活性和齐聚或聚合产物的影响;分别以钛和镍配合物催化剂为例,介绍了前过渡金属和后过渡金属催化乙烯齐聚或聚合的机理。     

齐聚苯胺修饰的三联吡啶铁配合物的合成及其光谱和电化学性质

合成了一系列齐聚苯胺修饰的三联吡啶铁配合物,研究了齐聚苯胺链长、不同取代基等对配合物光谱性质和氧化还原性质的影响。 结果表明,相对于配合物[Fe(TPY)₂]²⁺(TPY:三联吡啶),供电子齐聚苯胺单元的引入,使得修饰基团与配合物中心核[Fe(TPY)₂]²⁺之间形成了强的D-A体系,导致配合物¹MLCT吸收波长显著红移至594 nm,且摩尔吸光系数增加近5倍。 配合物同时具有基于金属中心、三联吡啶配体和齐聚苯胺单元的多个氧化还原过程,强拉电子取代基使齐聚苯胺单元氧化还原峰简并且峰电势明显正移,而正丁基取代基对氧化还原峰电势的影响较小。     

双核水杨醛亚胺铁系催化剂的合成及对乙烯齐聚催化性能的研究

以1.0代(1.0G)树枝状大分子、水杨醛和FeCl_2·4H_2O为原料,依次经过希夫碱反应和络合反应合成了一种双核水杨醛亚胺铁系催化剂。FT-IR、1 H NMR、UV和MS证实合成产物的结构与理论结构相符。以甲基铝氧烷(MAO)为助催化剂,考察了溶剂种类、反应温度、反应压力、Al/Fe摩尔比及金属活性中心种类对催化体系催化乙烯齐聚性能的影响。结果表明,当以甲苯为溶剂,聚合时间为30min,反应温度为15℃、反应压力为0.5MPa、Al/Fe摩尔比为1000时,该双核水杨醛亚胺铁系催化剂的活性可达1.14×10~5g/(mol Fe·h),齐聚产物中C_4及C_6烯烃含量高达90%以上。     

CO_2加氢活性与担载铁催化剂表面Fe-O键强度的关系

采用浸渍 -还原法 ,制备了 Al2 O3、 Ti O2 、 Zr O2 担载铁催化剂 ,并在温度 6 2 3K、压力 1.5 MPa、空速80 0～ 10 0 0 h- 1、原料气组成 CO2 /H2 为 1∶ 2等实验条件下 ,考察了不同还原温度的催化剂在 CO2 加氢制低碳(C2 ～ C5 )烃中的反应活性 .结果表明 ,以 CO2 转化率计 ,各催化剂均存在最佳还原温度 (Fe/Al2 O3:873K;Fe/Ti O2 :773K;Fe/Zr O2 :72 3K) .将此温度与催化剂表面 Fe- O键强度相关联 ,发现在相同条件下 ,与载体 M-O键长有关的 Fe- O键越强 ,催化剂越容易被还原 ,最佳还原温度越低 ,反应活性越好 .     

CO加氢制备低碳烯烃Fe基和Co基催化剂研究进展

CO加氢制备低碳烯烃是非石油路线获得烯烃的重要反应,其反应路线有直接法和间接法.直接法制备低碳烯烃具有反应路线短、能源利用率高、经济高效等优势.综述了近年来Fe基催化剂、 Co基催化剂在CO直接制备低碳烯烃中的研究进展.分析认为:费托合成过程产物选择性遵循Anderson-Schulz-Flory(ASF)分布规律,助剂和载体的使用一定程度提高Fe基、 Co基催化剂的低碳烯烃选择性.     

新型链行走烯烃聚合催化剂的合成及其催化活性

以二氯化镍为原料制得配合物(DME)Ni Cl2(1);以2,6-二异丙基苯胺和丁二酮为原料,经缩合反应制得α-二亚胺配体(2);1与2经络合反应合成了一种用于乙烯齐聚制备超支化聚乙烯的新型链行走催化剂(3),其结构经IR,XRD和元素分析表征。以乙烯齐聚为探针反应,考察了助催化剂,反应温度和反应时间对3催化活性的影响。结果表明:在较优反应条件[Al Et30.14 mol,n(Al)∶n(Ni)=600,于20℃反应0.5 h]下,3催化活性为2.5×106g PE·(mol·Ni·h·MPa)-1。齐聚产物为支化聚乙烯,部分支链中碳原子数大于4。     

Prospects and crucial problems in oligomerization and polymerization with iron and cobalt complex catalysts

<正>The discovery of highly active 2,6-bis(imino)pyridyl iron and cobalt complexes provided a milestone of latetransition metal catalysts for ethylene oligomerization and polymerization with being currently investigated for the scale-up process.The crucial problems are remaining in the catalytic systems:the catalytic systems targeting ethylene polymerization produce more oligomers at elevated reaction temperatures,however,there is a recognizable amount of high-molecular-weight polyethylene remained in the modified catalytic system for the oligomerization process.Beyond the modification of bis(imino)pyridyl metal complexes,several alternative procatalysts' models have been developed in our group.This review highlighted the achievements in exploring new iron and cobalt complexes with tridentate NNN ligands as procatalysts for ethylene oligomerization and polymerization.     

A series of novel 2,6-bis(imino)pyridyl iron catalysts: synthesis, characterization and ethylene oligomerization

A series of novel 2,6-bis(imino)pyridyl iron complexes {2,6-(2-X-4-Y-5-ZC₆H₂NCCH₃)₂C₅H₃N}FeCl₂ (X = Cl, Y = CH₃, Z = H (2); X = Br, Y = CH₃, Z = H (3); X = F, Y = H, Z = CH₃ (4); X = Cl, Y = H, Z = CH₃ (5); X = Cl, Y = F (7)) have been synthesized and characterized with elemental analysis and IR. These iron coordinative complexes, activated with methylaluminoxane (MAO), lead to highly active ethylene oligomerization (>10⁷ g/mol Fe h) and the products are mostly linear α-olefins (>90%). The catalytic activities and product properties depend on the substituents on aryl rings and the reaction conditions. As reaction temperature increases, the catalytic activities decrease rapidly and more low-molar-mass products are produced. The product distributions are almost independent of the Al/Fe molar ratio, but the catalytic activities change in different trends when the ortho-substituents on the aryl rings are different. The other three complexes have also been synthesized for comparison to investigate the steric hindrance and electronic effect on the properties of complexes. The complex with adaptable steric hindrance and electronic properties exhibits the highest catalytic activities.     

THE INFLUENCE OF SUBSTITUENT ELECTRONIC EFFECT ON ETHYLENE OLIGOMERIZATION ACTIVITIES OF BIS(IMINO)PYRIDYL Fe(II) CATALYSTS: A COMBINED MOLECULAR MECHANICS AND CHARGE EQUILIBRATION METHOD

 Bis(imino)pyridyl Fe(II) complexes are important catalysts in ethylene oligomerization for preparing α-olefins. The metal net charge-activity relationship of bis(imino)pyridyl Fe(II) complexes was investigated by molecular mechanics (MM) and net charge equilibration (QEq) method with modified Dreiding force field. It was found that metal net charge was in reverse ratio to ethylene oligomerization activity. Electron-donor substituents with less steric hindrance to the central metal were favorable to Fe complex activity. Metal net charge-activity relationship could be used to assist the design of new Fe oligomerization catalysts with higher activity.     

一种新型双亚胺吡啶铁系催化剂的乙烯低聚研究

线性α 烯烃广泛地应用于洗涤剂、增塑剂、润滑油等精细化学品的合成以及作为共单体制备线性低密度聚乙烯 (ＬＬＤＰＥ) .目前工业上主要是应用ＳＨＯＰ法[1] 、Ｃｈｅｖｒｏｎ工艺和Ａｍｏｃｏ工艺[2 ] 通过乙烯低聚制备 .近些年发展起来的新型高活性后过渡金属乙烯低聚催化剂能够高选择性地制备线性α 烯烃[3 ,4] .Ｂｒｏｏｋｈａｒｔ等[4] 的研究表明 ,对于双亚胺吡啶铁系乙烯聚合催化剂而言 ,配体上苯基的邻位取代基位阻减小可以实现乙烯低聚 ,并具有高活性、高选择性以及理想的低聚产物分布 .本文的工作是从配体的空间位阻效应对催化剂…     

Iron-catalyzed intermolecular [2π+2π] cycloaddition

The bis(imino)pyridine iron dinitrogen compounds, ((iPr)PDI)Fe(N(2))(2) and [((Me)PDI)Fe(N(2))](2)(μ(2)-N(2)) ((R)PDI = 2,6-(2,6-R(2)-C(6)H(3)N═CMe)(2)C(5)H(3)N; R = (i)Pr, Me), promote the catalytic intermolecular [2π + 2π] cycloaddition of ethylene and butadiene to form vinylcyclobutane. Stoichiometric experiments resulted in isolation of a catalytically competent iron metallocycle intermediate, which was shown to undergo diene-induced C-C reductive elimination. Deuterium labeling experiments establish competitive cyclometalation of the bis(imino)pyridine aryl substituents during catalytic turnover.     

Our variations on iron and cobalt catalysts toward ethylene oligomerization and polymerization

Iron and cobalt complexes are a new family of catalysts for ethylene oligomerization and polymerization. The extensive researches on bis(imino)pyridyl metal complexes have been carried out with the aim of synthesizing their derivatives and finding suitable reaction parameters for the optimum activity. Beyond the modification works of bis(imino)pyridyl metal complexes, several alternative models with similar coordination sphere have been developed in our group. This review article describes our experiences in innovating new models of iron and cobalt complexes as catalysts for ethylene oligomerization and polymerization.     

Effects of hydrogen in ethylene polymerization and oligomerization with magnesium chloride‐supported bis(imino)pyridyl iron catalysts

The effects of hydrogen in ethylene polymerization and oligomerization with different bis(imino)pyridyl iron(II) complexes immobilized on supports of type MgCl₂/AlEt_n(OEt)_3–n have been investigated. Hydrogen has a significant activating effect on polymerization catalysts containing relatively bulky bis(imino)pyridyl ligands, but this is not the case in ethylene oligomerization with a catalyst containing relatively little steric bulk in the ligand. It was found that the presence of hydrogen in the latter system led to decreased activity and an overall increase rather than a decrease in product molecular weight, indicating deactivation of active species producing low molecular weight polymer and oligomer. Decreased formation of vinyl‐terminated oligomers in the presence of hydrogen can therefore contribute to the activating effect of hydrogen in ethylene polymerization with immobilized iron catalysts, if it is assumed that hydrogen activation is related to chain transfer after a 2,1‐insertion of a vinyl‐terminated oligomer into the growing polymer chain. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4054–4061, 2007     

Iron(III) complexes bearing 2-(benzimidazole)-6-(1-aryliminoethyl)pyridines: Synthesis, characterization and their catalytic behaviors towards ethylene oligomerization and polymerization

A series of iron(III) complexes ligated by 2-(benzimidazole)-6-(1-aryliminoethyl)pyridines was synthesized and examined by ¹H NMR, ESI-MS, IR spectroscopic, elemental analysis and X-ray photoelectron spectroscopy (XPS). Activated with methylaluminoxane (MAO), all ferric complexes exhibited good activities (up to 5.38 × 10⁶ g mol⁻¹(Fe) h⁻¹) of ethylene oligomerization and polymerization, and resultant oligomers and polyethylene waxes showed high α-olefin feature, meanwhile the distribution of oligomers mostly resembled Schulz-Flory rules. The various reaction parameters were investigated in detail, and the less bulky and electron-withdrawing substituents of ligands could enhance the catalytic activities of their ferric complexes. The observations explain the cause for unstable activities performed by stored iron(II) complexes.     

Transition metal complexes bearing 2,6-bis(imino)pyridyl:Synthesis, structure, ethylene polymerization/oligomerization studies

A series of new complexes {2,6-bis[1-((2-methyl-4-methoxyphenyl)imino)ethyl]pyri-dine}MCI2 [M=Fe(Ⅱ) (2), Co(Ⅱ) (3), Ni(Ⅱ) (4), Cu(Ⅱ) (5), Zn(Ⅱ) (6)] have been synthesized. At 25℃, using 500 equiv of methylaluminoxane (MAO), the activities of Fe(Ⅱ), Co(Ⅱ) catalysts can reach 4.02×106 g/mol-Fehatm for ethylene polymerization and 3.98×105 g/mol-Cohatm for ethylene oligomerization. The effects of polymerization conditions such as reaction temperature, Al/M molar ratio and time on the activity of catalyst have been explored.     

铁、钴催化剂乙烯聚合原位紫外-可见光谱研究

利用乙烯常压聚合原位紫外 可见 (UV Vis)光谱技术 ,对 3个铁、钴络合物作为催化剂前体的催化剂体系进行了研究 .3个铁、钴络合物分别为 2 ,6 双 [1 (2 ,6 二甲基苯基亚胺 )乙基 ]吡啶二氯化铁 (a)、2 ,6 双 [1 (2 ,4,6 三甲基苯基亚胺 )乙基 ]吡啶二氯化铁 (b)和 2 ,6 双 [1 (2 ,6 二异丙基苯基亚胺 )乙基 ]吡啶二氯化钴(c) .实验结果表明 ,MAO对络合物催化剂前体的活化作用是一个快速过程 ;在聚合条件下分别观察到 5 6 0、6 30和 5 80nm的活性峰 ,考察了它们在聚合过程中的生长和在加入无水乙醇逐步使催化剂中毒时活性峰的消失规律 .对催化剂活性物种的结构和聚合机理进行了探讨