Determination of cyclophosphamide and ifosfamide in sewage effluent by stable isotope-dilution liquid chromatography-tandem mass spectrometry

A reliable and specific method was developed for the determination of the cytotoxic drugs cyclophosphamide and ifosfamide in sewage effluent. The most successful combination was found to be Strata-X solid-phase extraction followed by Florisil^® clean-up with analysis by liquid chromatography–tandem mass spectrometry. Quantification by internal standardisation was achieved using custom synthesised d4-cyclophophosphamide. The mass spectrometer was operated in highly selective reaction monitoring (HSRM) mode, which significantly reduced matrix noise and improved sensitivity. Although it suffered from some ionisation suppression, electrospray ionisation (ESI) was found to give an order of magnitude better sensitivity in terms of limit of detection than atmospheric pressure chemical ionisation (APCI). Using final effluent from two different sewage treatment plants, the method was validated following official European guidelines and shown to be a high performance tool for routine analysis at the sub-nanogram per litre level. Depending on the matrix, the limit of detection for cyclophosphamide was between 0.03 ng/L and 0.12 ng/L and for ifosfamide between 0.05 ng/L and 0.09 ng/L. For cyclophosphamide the accuracy and precision, tested at 1.7 ng/L, were 98–109% and ≤13%, CV respectively. For ifosfamide the accuracy and precision, tested at 1.1 ng/L, were 98–113% and ≤15% CV, respectively. Depending on the sample matrix the absolute recovery of the internal standard was between 57% and 70%. The method was tested by analysis of spot samples taken from the final effluent discharges of two sewage treatment plants; the first using a conventional trickling filter treatment process and second employing activated sludge followed by ultra violet treatment. Cyclophosphamide was detected at 0.19 ng/L at the first plant and at the second detected at 3.7 ng/L and 3.5 ng/L, before and after the UV treatment process; ifosfamide was not detectable at either plant.     

Determination of endogenous and exogenous estrogens in effluents from sewage treatment plants at the ng/L-level

An analytical method for the determination of the major endogenous and exogenous estrogenic steriods in effluent water samples of sewage treatment plants (STPs) with a LOQ down to 1 ng/L and below has been developed. The exogenous estrogen 17α-ethynylestradiol, frequently used as estrogenic component in oral contraceptives, and the endogenous estrogen 17β-estradiol show the highest estrogenic potential, therefore they were part of our target compounds. In addition, the content of the synthetic gestagen levonorgestrel, also often administered in oral contraceptives, was determined. A solid-phase extraction system for high volume sampling of water up to 25 L was implemented. Two types of adsorbent, Amberlite XAD 2 and a mixture of LiChrolut EN/Bondesil C-18, respectively, were tested for their extraction efficiency of these polar analytes. Recovery rates with LiChrolut EN/¶Bondesil C-18 ranged up to 94 %, whereas sampling on XAD 2 led only to poor recoveries below 40 %. After a liquid chromatographic clean-up step on silicagel the steroids were converted into their trimethylsilyl-ethers by the reaction with MSTFA/TMSI (N-methyl-N-trimethylsilyl-2,2,2-trifluoroacetamide, trimethylsilyliodide) and were then determined by HRGC/MS in the selected ion mode. A limit of quantification over the whole procedure of at least 1 ng/L was reached for all analytes. In several effluent samples the input of estrogens by the STP of the cities Ulm and New Ulm into the river Danube was characterised. The concentrations commonly found ranged from 1 ng/L up to 13 ng/L, depending on the respective steroid.     

Sonic spray ionization applied to liquid chromatography/mass spectrometry analysis of endocrine-disrupting chemicals in environmental water samples

A sonic spray ionization liquid chromatography/mass spectrometry (LC/SSI-MS) procedure combined with off-line solid-phase extraction was optimized for the analysis of 20 endocrine-disrupting chemicals (EDCs) in water samples. Method development included a comparison of the novel sonic spray ionization (SSI) with more traditional ion sources, i.e. pneumatically assisted electrospray ionization (ESI) and atmospheric pressure chemical ionization (APCI). It was demonstrated that SSI and ESI spectra were very similar, but were more prone to the formation of solvent cluster ions as compared with APCI spectra. This phenomenon was most prominent for SSI and resulted in an increased chemical background in full-scan mass spectra. However, this chemical noise did not affect the overall sensitivity of SSI and ESI. After optimization of LC and MS parameters, the LC/SSI-MS method was validated. Recoveries ranged from 76.3 up to 113.4% for all compounds. Limits of detection (LOD) and quantitation (LOQ) were established between 3.0 and 11.5 ng/L and 9.9 and 38.0 ng/L, respectively. Within-day (n = 5) and between-day (n = 5) reproducibility were investigated at three levels and ranged from 3.3-16.5% and 7.6-19.2%, respectively. Eight-point calibration curves were established and showed linearity for all compounds (r(2) > 0.987) over a linear dynamic range of 10-10 000 ng/L.     

Determination of antibiotics such as macrolides,ionophores and tiamulin in liquid manure by HPLC–MS/MS

A method for the analysis of several macrolide and ionophore antibiotics as well as tiamulin in liquid manure was developed. Reversed-phase liquid chromatography and atmospheric pressure chemical ionisation (APCI) tandem mass spectrometry was used for detection.High-performance liquid chromatographic (HPLC) separation of the antibiotics was achieved in 35 min. The analytes were extracted with ethyl acetate and the extracts were cleaned up by solid-phase extraction on a diol SPE cartridge. Recovery experiments with spiked liquid manure concentrations varying from 6 to 2,000 microg kg(-1) gave constant recovery rates. The recovery rates for the macrolides erythromycin, roxithromycin and oleandomycin were 75-94%, that for the ionophore salinomycin was 119%, while that for the pleuromutilin tiamulin was 123%, when using a macrolide internal standard. The relative standard deviation was found to be 15-36% and the limits of detection were 0.4-11.0 micro g kg(-1).The maximum concentrations found in manure samples were 43 micro g kg(-1) for tiamulin and 11 micro g kg(-1) for salinomycin.     

固相萃取液相色谱-质谱/质谱联用测定河水中大环内酯类抗生素

应用固相萃取（SPE）及LC—MS／MS技术,建立了水中痕量大环内酯类抗生素即红霉素、脱水红霉素、罗红霉素的分析方法,优化了固相萃取、液相色谱-质谱／质谱等相关条件。水样经HLB固相萃取柱富集净化,以多反应检测方式（MRM）对待测物进行定性和定量分析。3种抗生素在10-2000ng／L范围内具有良好的线性。其定量下限为5ng／L（S／N〉10）。加标纯水和实际水样的回收率在71％-111％之间,相对标准偏差（RSD）在3．7％-8．6％之间。该方法灵敏度高、选择性好、准确度高,适合实际水样中痕量大环内酯类药物的检测。使用该方法测得珠江广州河段某水样中红霉素、脱水红霉素和罗红霉素质量浓度分别为164、291和134ng／L。     

LC-MS/MS profiling for detection of endogenous steroids and prostaglandins in tissue samples

Roles of steroid hormones, and compounds that can influence their levels in cells, are of increasing interest in e.g. cancer research, partly because resistance to hormone therapies often complicates treatment. To elucidate the processes involved, the hormones and related compounds need to be accurately measured. Reversed-phase liquid chromatography with dynamic multiple reaction monitoring mass spectrometric detection in electrospray mode is capable of providing such measurements. Therefore, LC-MS/MS was developed for sensitive, selective analysis of 11 steroid hormones, cholesterol and two prostaglandins. The effects of the tissue matrix, and solid-phase extraction (SPE) sample clean-up, on the LC-MS/MS signals of the hormones were also investigated. The results show that the developed LC-MS/MS method, following SPE clean-up to reduce matrix interference, can detect selected steroids in extracts of mouse tissues. The method provides linear measurements of the steroids at concentrations up to few ng/μL, and limits of detection in the range 0.03-0.2 pg/μL (for some compounds lower than those of previously reported methods).     

Identification and characterization of impurities in an insecticide,bifenthrin technical

The HPLC‐DAD and GC/MS methods were successfully used for the identification and characterization of the impurities in an agrochemical insecticide, bifenthrin technical. Three impurities ranging from 0.175%–0.541% were detected by the HPLC‐DAD method. The LC/MS technique with ESI or APCI source failed to detect the impurities detected by HPLC‐DAD, due to lack of ionization in ESI or APCI. The three impurities were enriched by prep‐HPLC, and then their structures were elucidated based on the GC/EIMS and CIMS data. The EI mass spectra of bifenthrin and its impurities displayed molecular ion and provided structure indicative fragment ions; the CIMS data further confirmed their molecular weight. The identity of the impurity 1 was further confirmed by the synthesis of the authentic sample followed by NMR and GC/MS data.     

Detecting aristolochic acids in herbal remedies by liquid chromatography/serial mass spectrometry

Targeted liquid chromatography/serial mass spectrometry (LC/MS/MS) analysis, using a quadrupole ion-trap mass spectrometer, permitted the detection of aristolochic acids I and II in crude 70% methanol extracts of multi-component herbal remedies without any clean-up or concentration stages. The best ionisation characteristics were obtained using atmospheric pressure chemical ionisation (APCI) and by including ammonium ions in the mobile phase. Limits of detection for aristolochic acids were influenced by the level of interference created by other components in the sample matrix. They were determined to be between 250 pg and 2.5 ng on-column within a matrix containing compounds extracted from 2 mg of herbal remedy. With a herbal remedy that only permitted the higher limit of detection, this sensitivity was sufficient to detect the aristolochic acids extracted from 0.1% dry weight of Aristolochia manshuriensis included in the preparation.     

Comparison of multiple API techniques for the simultaneous detection of microconstituents in water by on‐line SPE‐LC‐MS/MS

This study described a fully automated method using on‐line solid phase extraction of large volume injections coupled with high performance liquid chromatography (HPLC) and tandem mass spectrometry (MS/MS) to simultaneously detect a group of recalcitrant microconstituents (pharmaceuticals and personal care products, steroid hormones and sterols) in aqueous matrices. Samples (1 mL to 20 mL) were loaded to the preconcentration column at 1 mL/min, and the column was washed with 1000 μL of 25% methanol in LC/MS water to remove polar and ionic interferences before LC‐MS/MS analysis. Three different atmospheric pressure ionization (API) techniques, including photoionization (APPI) with four different dopants (acetone, anisole, chlorobenzene and toluene), heated electrospray ionization (HESI) and atmospheric pressure chemical ionization (APCI), were evaluated on the basis of method detection limits (MDLs) and recoveries from different aqueous matrixes. Results indicated that APPI with toluene as dopant was the most sensitive ionization method for the majority of the analytes. When using 5 mL of sample, MDLs for pharmaceuticals and personal care products, including carbamazepine, DEET, caffeine, naproxen, acetaminophen and primidone, were between 0.3 ng/L and 15 ng/L. MDLs of hormones, including testosterone, equilenin, progesterone, equilin, 17β‐estradiol, 17α‐ethynylestradiol, estrone, androsterone, mestranol and estriol, were between 1.2 ng/L and 37 ng/L. The combination of APPI with dopant allowed the detection of two difficult to ionize fecal related sterols, such as coprostan‐3‐ol and coprostan‐3‐one with MDLs of 5.4 ng/L and 11 ng/L, respectively. Calculated MDLs are more than adequate for analysis of wastewater using 1 to 5 mL sample size and for surface waters using up to 20 mL sample size. Copyright © 2012 John Wiley & Sons, Ltd.     

Electrospray and atmospheric pressure chemical ionization tandem mass spectrometric behavior of eight anabolic steroid glucuronides

Mass spectrometric and tandem mass spectrometric behavior of eight anabolic steroid glucuronides were examined using electrospray (ESI) and atmospheric pressure chemical ionization (APCI) in negative and positive ion mode. The objective was to elucidate the most suitable ionization method to produce intense structure specific product ions and to examine the possibilities of distinguishing between isomeric steroid glucuronides. The analytes were glucuronide conjugates of testosterone (TG), epitestosterone (ETG), nandrolone (NG), androsterone (AG), 5alpha-estran-3alpha-ol-17-one (5alpha-NG), 5beta-estran-3alpha-ol-17-one (5beta-NG), 17alpha-methyl-5alpha-androstane-3alpha,17beta-diol (5alpha-MTG), and 17alpha-methyl-5beta-androstane-3alpha,17beta-diol (5beta-MTG), the last four being new compounds synthesized with enzyme-assisted method in our laboratory. High proton affinity of the 4-ene-3-one system in the steroid structure favored the formation of protonated molecule [M + H]+ in positive ion mode mass spectrometry (MS), whereas the steroid glucuronides with lower proton affinities were detected mainly as ammonium adducts [M + NH4]+. The only ion produced in negative ion mode mass spectrometry was a very intense and stable deprotonated molecule [M - H]- . Positive ion ESI and APCI MS/MS spectra showed abundant and structure specific product ions [M + H - Glu]+, [M + H - Glu - H2O]+, and [M + H - Glu - 2H2O]+ of protonated molecules and corresponding ions of the ammonium adduct ions. The ratio of the relative abundances of these ions and the stability of the precursor ion provided distinction of 5alpha-NG and 5beta-NG isomers and TG and ETG isomers. Corresponding diagnostic ions were only minor peaks in negative ion MS/MS spectra. It was shown that positive ion ESI MS/MS is the most promising method for further development of LC-MS methods for anabolic steroid glucuronides.     

Validated assay for the simultaneous quantification of total vincristine and actinomycin‐D concentrations in human EDTA plasma and of vincristine concentrations in human plasma ultrafiltrate by high‐performance liquid chromatography coupled with tandem mass spectrometry

A sensitive, specific and efficient high‐performance liquid chromatography/tandem mass spectrometry (HPLC/MS/MS) assay for the simultaneous determination of total vincristine and actinomycin‐D concentrations in human plasma and an assay for the determination of unbound vincristine are presented. Electrospray ionization (ESI), atmospheric pressure chemical ionization (APCI) and heated electrospray ionization (H‐ESI) were tested as ionization interfaces. For reasons of robustness ESI was chosen followed by tandem mass spectrometry (ESI‐MS/MS). For the plasma assay a 30 µL aliquot was protein precipitated with acetonitrile/methanol (50:50, v/v) containing the internal standard vinorelbine and 10 µL volumes were injected onto the HPLC system. To determine unbound vincristine, ultrafiltrate was produced from plasma using 30 kDa centrifugal filter units. The plasma ultrafiltrate was mixed with methanol (50:50, v/v), internal standard vinorelbine was added and 20 µL aliquots were injected onto the HPLC system. Separation was achieved on a 50 × 2.1 mm i.d. Xbridge C₁₈ column using 1 mM ammonium acetate/acetonitrile (30:70, v/v) adjusted to pH 10.5 with ammonia, run in a gradient with methanol at a flow rate of 0.4 mL/min. HPLC run time was 6 min. The assay quantifies in plasma vincristine from 0.25 to 100 ng/mL and actinomycin‐D from 0.5 to 250 ng/mL using plasma sample volumes of only 30 µL. Vincristine in plasma ultrafiltrate can be quantified from 1 to 100 ng/mL. Validation results demonstrate that vincristine and actinomycin‐D can be accurately and precisely quantified in human plasma and plasma ultrafiltrate with the presented methods. The assays are now in use to support clinical pharmacological studies in children treated with vincristine and actinomycin‐D. Copyright © 2009 John Wiley & Sons, Ltd.     

Ionisation in the absence of high voltage using supercritical fluid chromatography: a possible route to increased signal

Supercritical fluid chromatography (SFC) is fast becoming a technique of choice for the analysis of a wide range of compounds and has been found to be complementary to high-performance liquid chromatography (HPLC). The combination of SFC and mass spectrometry (MS) affords a very useful tool in the separation and analysis of compounds. In this study the ionisation of samples in the absence of an applied electrospray voltage has been observed when using SFC/MS, with some compounds showing increased sensitivity when all ionisation source high voltage (HV) is removed. In an attempt to understand the mechanism of ionisation, a series of test compounds were analysed using standard electrospray ionisation (ESI) and atmospheric pressure chemical ionisation (APCI) source configurations and also different API source designs. In both cases, data were acquired with the applied high voltage on (normal conditions) or with the high voltage off, i.e. no voltage spray (novo-spray). The standards were analysed with a range of pressure and modifier percentage conditions. To understand the nature of the ionisation process observed, this was compared with three established liquid-to-gas ionisation mechanisms. These were thermospray (TSP), charge residue model (CRM) of ESI and sonic spray ionisation (SSI). Experiments were undertaken in an attempt to explain this ionisation phenomenon and quantify any observed change in sensitivity. The most important point to note is that enhanced ionisation was observed under novo-spray conditions in a SFC/MS configuration, which in certain cases provides a lowering in the overall limit of detection (LOD).     

Analysis of polycyclic aromatic hydrocarbons by liquid chromatography/tandem mass spectrometry using atmospheric pressure chemical ionization or electrospray ionization with tropylium post-column derivatization

Polycyclic aromatic hydrocarbons (PAHs) with four to six rings are potent carcinogens. This study analyzed ten of the sixteen US EPA priority PAHs using reversed-phase liquid chromatography/tandem mass spectrometry (LC/MS/MS) in selected reaction monitoring mode with two ionization sources: positive atmospheric pressure chemical ionization (APCI+) or positive elecrtrospray ionization (ESI+) with tropylium post-column derivatization. Several factors were investigated, including mobile phases, stationary phases of columns and chromatographic temperature, to determine how optimal separation and sensitivity might be achieved. Methanol used as an organic mobile phase provided better sensitivities for most PAHs than acetonitrile, although some PAHs co-eluted. Acidic buffers did not increase analyte signals. Use of Restek Pinnacle II PAH columns (250 x 4.6 mm or 250 x 2.1 mm, 5 microm) with water/acetonitrile gradient at 27 degrees C made possible a good separation of the ten analytes. [M]+. were the best precursor ions in both APCI and ESI, although fluoranthene could not be detected in ESI mode when tropylium post-column derivatization was performed. [M-28]+ and [M-52]+ were the major product ions of PAHs after collision-induced dissociation, a result of neutral losses of C(2)H(4) and (C(2)H(2))(2), respectively. Chromatographic separation for PAH isomers was crucial because the mass spectra were so similar that even MS/MS could not distinguish them from each other. The recoveries of sample preparations of PAHs spiked onto air-sampling filters ranged between 77.5 and 106% with relative standard deviations between 1.1 and 15.9%. This method was validated by analyzing NIST SRM 1649a (urban dust), producing results comparable with the certified PAH concentrations. The detection limits using APCI and ESI interfaces, defined as three times the noise levels, ranged between 0.23 and 0.83 ng and between 0.16 and 0.84 ng of on-column injection, respectively.     

Rapid screening procedures for the hydrolysis products of chemical warfare agents using positive and negative ion liquid chromatography-mass spectrometry with atmospheric pressure chemical ionisation

Qualitative screening procedures have been developed for the rapid detection and identification of the hydrolysis products of chemical warfare agents in aqueous samples and extracts, using liquid chromatography-mass spectrometry with positive and negative atmospheric pressure chemical ionisation (APCI). Previously reported screening procedures, which used positive APCI or electrospray ionisation (ESI), were modified by using LC conditions that allowed acquisition of positive and negative ion mass spectra. APCI was generally found to be more robust than ESI, probably due to variable adduct ion formation with ESI, depending on the condition of the sample and the system. Negative APCI provided selective detection of acidic analytes and allowed facile differentiation of alkyl alkylphosphonic acids from isomeric dialkyl alkylphosphonates. The combination of positive and negative APCI, using a C18 column and water-methanol mobile phase modified with ammonium formate, provides a rapid screening procedure for chemical warfare agent degradation products, with limits of detectability in the range 10-100 ng/ml. In the case of proficiency test samples, where analyte concentrations are in the range 1-10 ppm, introduction of the sample by infusion may provide an even faster preliminary screening procedure.     

A study of common discovery dosing formulation components and their potential for causing time-dependent matrix effects in high-performance liquid chromatography tandem mass spectrometry assays

Hydroxyproyl-beta-cyclodextran (HPBCD), methyl cellulose (MC), Tween 80 and PEG400 are commonly used in dosing formulations in pharmacokinetic (PK) studies during the early drug discovery stage. A series of studies was designed to evaluate the potential matrix effects of these dosing vehicles when the samples are assayed by high-performance liquid chromatography combined with tandem mass spectrometry (HPLC/MS/MS). These dosing vehicles were dosed into the rats via either an intravenous (IV) or an oral route (PO) and plasma samples were collected for a 24-h post-dose period. Five test compounds with CLog P values ranging from 0.9 to 5.4 were spiked into the collected rat plasma. After protein precipitation, these samples were analyzed using a generic fast-gradient HPLC/MS/MS method. Three popular mass spectrometers (Thermo-Finnigan Quantum with ESI and APCI, AB-Sciex API 3000 with ESI and APCI, and Waters-Micromass Quattro Ultima with ESI) were used to test these plasma samples. Results indicated that there was no observed matrix effect for all five compounds when 20% HPBCD or 0.4% MC was used as the vehicle in either the IV or the PO route, respectively. In addition, 0.1% Tween 80 dosed either IV or PO caused significant ion suppression (50-80%, compared to results obtained from plasma samples free from vehicles) for compounds that eluted at the beginning of the chromatogram. Also, PEG400 when used in an oral formulation caused significant ion suppression (30-50%) for early eluting compounds. These matrix effects were not only ionization mode (ESI or APCI) dependent, but also source design (Thermo-Finnigan, AB-Sciex or Waters-Micromass) dependent. Overall, the APCI mode proved to be less vulnerable to matrix effects than the ESI mode. Some possible mechanisms of these matrix effects are proposed and simple strategies to avoid these matrix effects are discussed.     

Capillary column supercritical fluid chromatography-atmospheric pressure ionisation mass spectrometry interface performance of atmospheric pressure chemical ionisation and electrospray ionisation.

A supercritical fluid chromatography interface probe for atmospheric pressure ionisation mass spectrometry (API-MS) with the advantage of convenient switch between ionisation modes [atmospheric pressure chemical ionisation (APCI) and electrospray ionisation (ESI)] has recently been reported [P.J.R. Sj?berg, K.E. Markides, J. Chromatogr. A, 785 (1997) 101]. In order to obtain a stable ion signal and a low minimum detectable quantity, the design of the spray devise has to be optimised. For easy optimisation in the APCI mode, the corona needle was mounted directly on the interface probe. To compensate for the adiabatic cooling of the expanding mobile phase in the APCI mode, a heated region around the restrictor tip was used. In comparison, ESI required no additional heat, which might also prevent fragmentation for thermolabile compounds. As the mobile phase used was neat CO2, a low flow of make-up liquid was utilised in the ESI mode for transfer of the analytes from the expanding CO2 gas to the liquid phase before ionisation. The low make-up liquid flow in the ESI mode was sufficient for preventing the restrictor from becoming blocked. Factors that influence the ion signal intensity and stability have been studied. In APCI mode, corona needle position, nebuliser gas flow and gas additives were studied and in ESI mode, spray capillary assembly dimension and position, liquid flow-rate and composition were studied. The achievable detection limits were in the 50-0.1 pg (i.e., 290 fmol-140 amol) range. The detection limit in APCI mode was improved by a factor of about 20-25 compared to an earlier design [L.N. Tyrefors, R.X. Moulder, K.E. Markides, Anal. Chem. 65 (1993) 2835].     

UPLC–TOF–MS Method for Simultaneous Quantification of Steroid Hormones in Tissue Homogenates of Zebrafish with Solid-Phase Extraction

The quantification of steroid hormones of individual zebrafish (Danio rerio) provides perspective to understand endogenous hormone function. A UPLC–TOF–MS method was developed to provide a reproducible, sensitive, and efficient assay to determine the concentration of steroid hormones, including cortisol, testosterone, androstenedione, 11-deoxycortisol, 11-deoxycorticosterone, and 17-hydroxyprogesterone in whole-body homogenates of each zebrafish. Solid-phase extraction was used to sample matrix clean-up and acquired a recovery from 89.7% to 107.9%. The analytes were separated on an Aquity BEH C18 column using gradient elution. Mass spectrometric analysis was performed by single reaction monitoring (SRM) using positive electrospray ionization mode. The total running time was 6 min, which was greatly shortened compared with a previously reported method. The developed method exhibited excellent linearity for all the analytes, with regression coefficients higher than 0.99. The limit of detection varied between 0.1 and 0.5 ng/L and the limit of quantification was 0.5–1.7 ng/L for all analytes. The precision of the method was assessed on replicate measurements and was found to be in the ranges of 1.9 % to 6.6% and 4.3% to 8.6%, for intra- and inter-day analysis, respectively. This method was validated according to FDA guidance and applied to determine steroid hormone levels in the tissue homogenate of zebrafish acutely treated with caffeine and ethanol.     

ESI outcompetes other ion sources in LC/MS trace analysis

Choosing an appropriate ion source is a crucial step in liquid chromatography mass spectrometry (LC/MS) method development. In this paper, we compare four ion sources for LC/MS analysis of 40 pesticides in tomato and garlic matrices. We compare electrospray ionisation (ESI) source, thermally focused/heated electrospray (HESI), atmospheric pressure photoionisation (APPI) source with and without dopant, and multimode source in ESI mode, atmospheric pressure chemical ionisation (APCI) mode, and combined mode using both ESI and APCI, i.e. altogether seven different ionisation modes. The lowest limits of detection (LoDs) were obtained by ESI and HESI. Widest linear ranges were observed with the conventional ESI source without heated nebuliser gas. In comparison to HESI, ESI source was significantly less affected by matrix effect. APPI ranked second (after ESI) by not being influenced by matrix effect; therefore, it would be a good alternative to ESI if low LoDs are not required.

Graphical abstract

     

Comparison of reversed-phase liquid chromatography-mass spectrometry with electrospray and atmospheric pressure chemical ionization for analysis of dietary tocopherols

ESI and APCI ionization techniques in both negative and positive ion modes were evaluated for simultaneous LC-MS analysis of the four tocopherol homologues (alpha, beta, gamma and delta). The ESI and APCI ionization of tocopherols in positive ion mode was not efficient and proceeded via two competitive mechanisms, with the formation of protonated pseudo-molecular ions and molecular ions, which adversely influenced the repeatability of MS signal. Ionization in negative ion mode in both ESI and APCI was more efficient as it only produced target deprotonated pseudo-molecular ions. The APCI in negative ion mode showed larger linearity range, lower detection limits and was less sensitive to the differences in chemical structure of analytes and nature of applied solvents than negative ion ESI. Negative ion APCI was, therefore, chosen for the development of LC-MS method for simultaneous determination of the four tocopherols in foods. A baseline separation of the tocopherols was achieved on novel pentafluorophenyl silica-based column Fluophase PFP. The use of methanol-water (95:5, v/v) as a mobile phase was preferable to the use of acetonitrile-water due to considerable gain in MS signal. The limits of quantifications were 9 ng/mL for alpha-tocopherol, 8 ng/mL for beta- and gamma- and 7.5 ng/mL for delta-tocopherol when 2 microL was injected. This method was successfully applied to determination of tocopherols in sunflower oil and milk.     

Determination of hormones in human urine by ultra‐high‐performance liquid chromatography/triple‐quadrupole mass spectrometry

Steroid hormones play a critical role in maintaining the homeostasis of human metabolism. Urine as a noninvasive sample has been extensively used in clinical diagnosis for hormones homeostasis. In this study, the simultaneous characterization of fourteen hormones in urine was performed based on ultra‐high‐performance liquid chromatography/electrospray ionization tandem mass spectrometry (UPHLC/ESI(+)‐MS/MS) with multiple reaction monitoring in the positive ionization mode. The target hormones were cortisone, cortisol, 11‐deoxycortisol, aldosterone, corticosterone, 11‐deoxycorticosterone, progesterone, 17‐OH‐progesterone, pregnenolone, estrone, estradiol, estriol, testosterone and dehydreopiandrosterone. β‐Glucuronidase/sulfatase deconjugation and liquid–liquid extraction (LLE) were conducted for the determination of urinary hormones (free + conjugated forms). The limits of detection (LODs) ranged from 0.2 ng/mL (11‐deoxycortisol and testosterone) to 1 ng/mL (cortisone). The extraction recovery of the targeted compounds ranged from 87% to 127%, indicating sufficient extraction efficiency for the LLE process. Intraday precision was below 10% and the accuracy ranged from 84% to 122%. The profiling analysis of hormones in urine samples helps to understand the metabolic state of biological systems and can be employed as a diagnostic tool in diseases developed by endocrine‐disrupted systems.